| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
| |
Fix rts5227&5249 failed send buffer cmd after suspend,
PM_CTRL3 should reset before send any buffer cmd after suspend.
Otherwise, buffer cmd will failed, this will lead resume fail.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In some platforms, specially Thinkpad series, rts5249 won't be
initialized properly. So we need adjust some phy parameters to
improve the compatibility issue.
It is a little different between simulation and real chip. We have
no idea about which configuration is better before tape-out. We set
default settings according to simulation, but need to tune these
parameters after getting the real chip.
I can't explain every change in detail here. The below information is
just a rough description:
PHY_REG_REV: Disable internal clkreq_tx, enable rx_pwst
PHY_BPCR: No change, just turn the magic number to macro definitions
PHY_PCR: Change OOBS sensitivity, from 60mV to 90mV
PHY_RCR2: Control charge-pump current automatically
PHY_FLD4: Use TX cmu reference clock
PHY_RDR: Change RXDSEL from 30nF to 1.9nF
PHY_RCR1: Change the duration between adp_st and asserting cp_en from
0.32 us to 0.64us
PHY_FLD3: Adjust internal timers
PHY_TUNE: Fine tune the regulator12 output voltage
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The default phase can meet most cards' requirement, but it is not the
optimal one. In some extreme situation, the rx phase point produced by
the following tuning process will drift quite a distance.
Before tuning UHS card, this patch will set a more proper initial tx
phase point, which is calculated from statistic data, and can achieve
a much better tx signal quality.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
| |
Update copyright date, remove author address and add Roger Tseng.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
| |
Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
| |
These actions are individual for each reader model, so should be put in
extra_init_hw instead of rtsx_pci_init_hw.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
|
RTS5249 supports SD UHS-II interface.
In order to support SD UHS-IIļ¼the definitions of some internal
registers of RTS5249 have to be modified and are different from its
predecessors. So we need this patch to ensure RTS5249 can work, even
SD/MMC stack doesn't support UHS-II interface.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
