summaryrefslogtreecommitdiffstats
path: root/drivers/net/Kconfig (follow)
Commit message (Collapse)AuthorAgeFilesLines
* rcu: Make SRCU optional by using CONFIG_SRCUPranith Kumar2015-01-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | SRCU is not necessary to be compiled by default in all cases. For tinification efforts not compiling SRCU unless necessary is desirable. The current patch tries to make compiling SRCU optional by introducing a new Kconfig option CONFIG_SRCU which is selected when any of the components making use of SRCU are selected. If we do not select CONFIG_SRCU, srcu.o will not be compiled at all. text data bss dec hex filename 2007 0 0 2007 7d7 kernel/rcu/srcu.o Size of arch/powerpc/boot/zImage changes from text data bss dec hex filename 831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before 829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after so the savings are about ~2000 bytes. Signed-off-by: Pranith Kumar <bobby.prani@gmail.com> CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com> CC: Josh Triplett <josh@joshtriplett.org> CC: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
* ipvlan: ipvlan depends on INET and IPV6Mahesh Bandewar2014-11-301-0/+2
| | | | | | | | | This driver uses ip_out_local() and ip6_route_output() which are defined only if CONFIG_INET and CONFIG_IPV6 are enabled respectively. Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipvlan: Initial check-in of the IPVLAN driver.Mahesh Bandewar2014-11-241-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: macvtap and tun depend on INETBen Hutchings2014-10-311-0/+2
| | | | | | | | | | | | | | These drivers now call ipv6_proxy_select_ident(), which is defined only if CONFIG_INET is enabled. However, they have really depended on CONFIG_INET for as long as they have allowed sending GSO packets from userland. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: f43798c27684 ("tun: Allow GSO using virtio_net_hdr") Fixes: b9fb9ee07e67 ("macvtap: add GSO/csum offload support") Fixes: 5188cd44c55d ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets") Signed-off-by: David S. Miller <davem@davemloft.net>
* openvswitch: fix a compilation error when CONFIG_INET is not setW!Andy Zhou2014-10-071-1/+0
| | | | | | | | | | | | | | | | | | | | Fix a openvswitch compilation error when CONFIG_INET is not set: ===================================================== In file included from include/net/geneve.h:4:0, from net/openvswitch/flow_netlink.c:45: include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads': >> include/net/udp_tunnel.h:100:2: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration] >> return iptunnel_handle_offloads(skb, udp_csum, type); >> ^ >> >> include/net/udp_tunnel.h:100:2: warning: return makes pointer from integer without a cast >> >> cc1: some warnings being treated as errors ===================================================== Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Andy Zhou <azhou@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxlan: Call udp_sock_createTom Herbert2014-07-151-0/+1
| | | | | | | | In vxlan driver call common function udp_sock_create to create the listener UDP port. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netpoll: Remove dead packet receive code (CONFIG_NETPOLL_TRAP)Eric W. Biederman2014-03-171-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | The netpoll packet receive code only becomes active if the netpoll rx_skb_hook is implemented, and there is not a single implementation of the netpoll rx_skb_hook in the kernel. All of the out of tree implementations I have found all call netpoll_poll which was removed from the kernel in 2011, so this change should not add any additional breakage. There are problems with the netpoll packet receive code. __netpoll_rx does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq context. netpoll_neigh_reply leaks every skb it receives. Reception of packets does not work successfully on stacked devices (aka bonding, team, bridge, and vlans). Given that the netpoll packet receive code is buggy, there are no out of tree users that will be merged soon, and the code has not been used for in tree for a decade let's just remove it. Reverting this commit can server as a starting point for anyone who wants to resurrect netpoll packet reception support. Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fix macvtap type name in KconfigJan Luebbe2014-02-131-1/+1
| | | | | | | | The netlink kind (and iproute2 type option) is actually called 'macvtap', not 'macvlan'. Signed-off-by: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* virtio-net: fix build error when CONFIG_AVERAGE is not enabledMichael Dalton2014-01-181-0/+1
| | | | | | | | | | | | | | Commit ab7db91705e9 ("virtio-net: auto-tune mergeable rx buffer size for improved performance") introduced a virtio-net dependency on EWMA. The inclusion of EWMA is controlled by CONFIG_AVERAGE. Fix build error when CONFIG_AVERAGE is not enabled by adding select AVERAGE to virtio-net's Kconfig entry. Build failure reported using config make ARCH=s390 defconfig. Signed-off-by: Michael Dalton <mwdalton@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* packet: nlmon: virtual netlink monitoring device for packet socketsDaniel Borkmann2013-06-251-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, there is no good possibility to debug netlink traffic that is being exchanged between kernel and user space. Therefore, this patch implements a netlink virtual device, so that netlink messages will be made visible to PF_PACKET sockets. Once there was an approach with a similar idea [1], but it got forgotten somehow. I think it makes most sense to accept the "overhead" of an extra netlink net device over implementing the same functionality from PF_PACKET sockets once again into netlink sockets. We have BPF filters that can already be easily applied which even have netlink extensions, we have RX_RING zero-copy between kernel- and user space that can be reused, and much more features. So instead of re-implementing all of this, we simply pass the skb to a given PF_PACKET socket for further analysis. Another nice benefit that comes from that is that no code needs to be changed in user space packet analyzers (maybe adding a dissector, but not more), thus out of the box, we can already capture pcap files of netlink traffic to debug/troubleshoot netlink problems. Also thanks goes to Thomas Graf, Flavio Leitner, Jesper Dangaard Brouer. [1] http://marc.info/?l=linux-netdev&m=113813401516110 Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Move MII out from under NET_CORE and hide itBen Hutchings2013-06-201-7/+3
| | | | | | | | | | | | | All drivers that select MII also need to select NET_CORE because MII depends on it. This is a bit ridiculous because NET_CORE is just a menu option that doesn't enable any code by itself. There is also no need for it to be a visible option, since its users all select it. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* VXLAN: Fix vxlan stats handling.Pravin B Shelar2013-03-261-0/+1
| | | | | | | | | | | | | | | Fixes bug in VXLAN code where is iptunnel_xmit() called with NULL dev->tstats. This bug was introduced in commit 6aed0c8bf7d2f389b (tunnel: use iptunnel_xmit() again). Following patch fixes bug by setting dev->tstats. It uses ip_tunnel module code to share stats function. CC: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2013-02-261-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking fixes from David Miller: 1) ping_err() ICMP error handler looks at wrong ICMP header, from Li Wei. 2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet. 3) netif_set_xps_queue() forgets to drop mutex on errors, fix from Alexander Duyck. 4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix from Eric Dumazet. 5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the amount of TCP option space was not taken into account properly in this code path. Fix from yuchung Cheng. 6) MLX4 driver allocates device queues with the wrong size, from Kleber Sacilotto. 7) sock_diag can access past the end of the sock_diag_handlers[] array, from Mathias Krause. 8) vlan_set_encap_proto() makes incorrect assumptions about where skb->data points, rework the logic so that it works regardless of where skb->data happens to be. From Jesse Gross. 9) Fix gianfar build failure with NET_POLL enabled, from Paul Gortmaker. 10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from Pravin B Shelar. 11) bgmac driver does: int i; for (i = 0; ...; ...) { ... for (i = 0; ...; ...) { effectively corrupting the outer loop index, use a seperate variable for the inner loops. From Rafał Miłecki. 12) Fix suspend bugs in smsc95xx driver, from Ming Lei. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits) usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND usbnet: smsc95xx: fix broken runtime suspend usbnet: smsc95xx: fix suspend failure bgmac: fix indexing of 2nd level loops b43: Fix lockdep splat on module unload Revert "ip_gre: propogate target device GSO capability to the tunnel device" IP_GRE: Fix GRE_CSUM case. VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification. IP_GRE: Fix IP-Identification. net/pasemi: Fix missing coding style vmxnet3: fix ethtool ring buffer size setting vmxnet3: make local function static bnx2x: remove dead code and make local funcs static gianfar: fix compile fail for NET_POLL=y due to struct packing vlan: adjust vlan_set_encap_proto() for its callers sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg sock_diag: Fix out-of-bounds access to sock_diag_handlers[] vxlan: remove depends on CONFIG_EXPERIMENTAL mlx4_en: fix allocation of CPU affinity reverse-map mlx4_en: fix allocation of device tx_cq ...
| * vxlan: remove depends on CONFIG_EXPERIMENTALKees Cook2013-02-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | The CONFIG_EXPERIMENTAL config item has not carried much meaning for a while now and is almost always enabled by default. As agreed during the Linux kernel summit, remove it from any "depends on" lines in Kconfigs. Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge tag 'char-misc-3.9-rc1' of ↵Linus Torvalds2013-02-211-0/+4
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver patches from Greg Kroah-Hartman: "Here's the big char/misc driver patches for 3.9-rc1. Nothing major here, just lots of different driver updates (mei, hyperv, ipack, extcon, vmci, etc.). All of these have been in the linux-next tree for a while." * tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits) w1: w1_therm: Add force-pullup option for "broken" sensors w1: ds2482: Added 1-Wire pull-up support to the driver vme: add missing put_device() after device_register() fails extcon: max8997: Use workqueue to check cable state after completing boot of platform extcon: max8997: Set default UART/USB path on probe extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type extcon: max8997: Set default of ADC debounce time during initialization extcon: max8997: Remove duplicate code related to set H/W line path extcon: max8997: Move defined constant to header file extcon: max77693: Make max77693_extcon_cable static extcon: max8997: Remove unreachable code extcon: max8997: Make max8997_extcon_cable static extcon: max77693: Remove unnecessary goto statement to improve readability extcon: max77693: Convert to devm_input_allocate_device() extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style CREDITS: update email and address of Harald Hoyer extcon: arizona: Use MICDET for final microphone identification extcon: arizona: Always take the first HPDET reading as the final one extcon: arizona: Clear _trig_sts bits after jack detection extcon: arizona: Don't HPDET magic when headphones are enabled ...
| * | net: Add support for NTB virtual ethernet deviceJon Mason2013-01-181-0/+4
| |/ | | | | | | | | | | | | | | | | | | A virtual ethernet device that uses the NTB transport API to send/receive data. Signed-off-by: Jon Mason <jon.mason@intel.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* / drivers/net: remove depends on CONFIG_EXPERIMENTALKees Cook2013-01-111-5/+4
|/ | | | | | | | | | | | | | The CONFIG_EXPERIMENTAL config item has not carried much meaning for a while now and is almost always enabled by default. As agreed during the Linux kernel summit, remove it from any "depends on" lines in Kconfigs. CC: "David S. Miller" <davem@davemloft.net> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Paul Gortmaker <paul.gortmaker@windriver.com> CC: Mike Sterling <Mike.Sterling@microsoft.com> CC: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: David S. Miller <davem@davemloft.net>
* vxlan: Depend on CONFIG_INETDavid S. Miller2012-10-021-1/+1
| | | | | Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* vxlan: virtual extensible lanstephen hemminger2012-10-021-0/+13
| | | | | | | | | | | | | | | | This is an implementation of Virtual eXtensible Local Area Network as described in draft RFC: http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02 The driver integrates a Virtual Tunnel Endpoint (VTEP) functionality that learns MAC to IP address mapping. This implementation has not been tested only against the Linux userspace implementation using TAP, not against other vendor's equipment. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/ieee802154: move ieee802154 drivers to net folderalex.bluesman.smirnov@gmail.com2012-08-301-2/+2
| | | | | | | | | | | The IEEE 802.15.4 standard represents a networking protocol. I don't exactly know why drivers for this protocol are stored into the root 'driver' folder, but better will be to store them with other networking stuff. Currently there are only 3 drivers available for IEEE 802.15.4 stack, so lets do it now with the smallest overhead. Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tokenring: delete all remaining driver supportPaul Gortmaker2012-05-161-2/+0
| | | | | | | | | | | | | | | This represents the mass deletion of the of the tokenring support. It gets rid of: - the net/tr.c which the drivers depended on - the drivers/net component - the Kbuild infrastructure around it - any tokenring related CONFIG_ settings in any defconfigs - the tokenring headers in the include/linux dir - the firmware associated with the tokenring drivers. - any associated token ring documentation. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* dummy: documentation is staleAlan Cox2012-05-151-4/+1
| | | | | | | | | dummy0/1/2 names are always used and there are options to set multiple dummy devices. Remove the obsolete text Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42865 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'staging-next' of ↵Linus Torvalds2012-01-091-0/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging * 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (466 commits) net/hyperv: Add support for jumbo frame up to 64KB net/hyperv: Add NETVSP protocol version negotiation net/hyperv: Remove unnecessary kmap_atomic in netvsc driver staging/rtl8192e: Register against lib80211 staging/rtl8192e: Convert to lib80211_crypt_info staging/rtl8192e: Convert to lib80211_crypt_data and lib80211_crypt_ops staging/rtl8192e: Add lib80211.h to rtllib.h staging/mei: add watchdog device registration wrappers drm/omap: GEM, deal with cache staging: vt6656: int.c, int.h: Change return of function to void staging: usbip: removed unused definitions from header staging: usbip: removed dead code from receive function staging:iio: Drop {mark,unmark}_in_use callbacks staging:iio: Drop buffer mark_param_change callback staging:iio: Drop the unused buffer enable() and is_enabled() callbacks staging:iio: Drop buffer busy flag staging:iio: Make sure a device is only opened once at a time staging:iio: Disallow modifying buffer size when buffer is enabled staging:iio: Disallow changing scan elements in all buffered modes staging:iio: Use iio_buffer_enabled instead of open coding it ... Fix up conflict in drivers/staging/iio/adc/ad799x_core.c (removal of module_init due to using module_i2c_driver() helper, next to removal of MODULE_ALIAS due to using MODULE_DEVICE_TABLE instead).
| * staging: hv: move hv_netvsc out of staging areaHaiyang Zhang2011-11-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | hv_netvsc has been reviewed on netdev mailing list on 6/09/2011. All recommended changes have been made. We are requesting to move it out of staging area. Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: KY Srinivasan <kys@microsoft.com> Signed-off-by: Mike Sterling <Mike.Sterling@microsoft.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | dsa: Move switch drivers to new directory drivers/net/dsaBen Hutchings2011-11-291-0/+2
| | | | | | | | | | | | | | | | Support for specific hardware belongs under drivers/net/ not net/. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2011-11-211-0/+2
|\| | | | | | | | | | | | | | | | | | | | | | | The forcedeth changes had a conflict with the conversion over to atomic u64 statistics in net-next. The libertas cfg.c code had a conflict with the bss reference counting fix by John Linville in net-next. Conflicts: drivers/net/ethernet/nvidia/forcedeth.c drivers/net/wireless/libertas/cfg.c
| * net: drivers/net/hippi/Kconfig should be sourcedPaul Bolle2011-11-091-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit ff5a3b509e ("hippi: Move the HIPPI driver") moved the HIPPI driver into drivers/net/hippi. It didn't source drivers/net/hippi/Kconfig though, so it didn't make all necessary Kconfig changes. So let drivers/net/kconfig source HIPPI's Kconfig file. [ Fix syntax error at the end of HIPP's Kconfig file. -DaveM ] Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: introduce ethernet teaming deviceJiri Pirko2011-11-131-0/+2
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces new network device called team. It supposes to be very fast, simple, userspace-driven alternative to existing bonding driver. Userspace library called libteam with couple of demo apps is available here: https://github.com/jpirko/libteam Note it's still in its dipers atm. team<->libteam use generic netlink for communication. That and rtnl suppose to be the only way to configure team device, no sysfs etc. Python binding of libteam was recently introduced. Daemon providing arpmon/miimon active-backup functionality will be introduced shortly. All what's necessary is already implemented in kernel team driver. v7->v8: - check ndo_ndo_vlan_rx_[add/kill]_vid functions before calling them. - use dev_kfree_skb_any() instead of dev_kfree_skb() v6->v7: - transmit and receive functions are not checked in hot paths. That also resolves memory leak on transmit when no port is present v5->v6: - changed couple of _rcu calls to non _rcu ones in non-readers v4->v5: - team_change_mtu() uses team->lock while travesing though port list - mac address changes are moved completely to jurisdiction of userspace daemon. This way the daemon can do FOM1, FOM2 and possibly other weird things with mac addresses. Only round-robin mode sets up all ports to bond's address then enslaved. - Extended Kconfig text v3->v4: - remove redundant synchronize_rcu from __team_change_mode() - revert "set and clear of mode_ops happens per pointer, not per byte" - extend comment of function __team_change_mode() v2->v3: - team_change_mtu() uses rcu version of list traversal to unwind - set and clear of mode_ops happens per pointer, not per byte - port hashlist changed to be embedded into team structure - error branch in team_port_enter() does cleanup now - fixed rtln->rtnl v1->v2: - modes are made as modules. Makes team more modular and extendable. - several commenters' nitpicks found on v1 were fixed - several other bugs were fixed. - note I ignored Eric's comment about roundrobin port selector as Eric's way may be easily implemented as another mode (mode "random") in future. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: Kconfig & Makefile cleanupJeff Kirsher2011-08-271-130/+137
| | | | | | | | | | | | | | The is does a general cleanup of the drivers/net/ Kconfig and Makefile. This patch create a "core" option and places all the networking core drivers into this option (default is yes for this option). In addition, it alphabitizes the Kconfig driver options. As a side cleanup, found that the arcnet, token ring, and PHY Kconfig options were a tri-state option and should have been a bool option. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* com20020_cs: Move the PCMCIA Arcnet driverJeff Kirsher2011-08-271-2/+0
| | | | | | | | | | | | Move the COM20020 PCMICA Arcnet driver into drivers/net/arcnet/ with the other Arcnet drivers. Made the necessary Kconfig and Makefile changes as well. Since this was the "last" PCMCIA driver in drivers/net/pcmcia/, this patch also cleans up the references to drivers/net/pcmcia. CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* slip: Move the SLIP driversJeff Kirsher2011-08-271-72/+2
| | | | | | | | | Move the Serial Line Internet Protocol (SLIP) drivers into drivers/net/slip/ and make the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Alan Cox <alan@linux.intel.com>
* plip: Move the PLIP driverJeff Kirsher2011-08-271-35/+2
| | | | | | | | | Move the Parallel Line Internet Protocol (PLIP) driver into drivers/net/plip/ and make the necessary Kconfig and Makefile changes. CC: Niibe Yutaka <gniibe@mri.co.jp> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Alan Cox <alan@linux.intel.com>
* hippi: Move the HIPPI driverJeff Kirsher2011-08-271-32/+0
| | | | | | | | | Move the HIPPI driver into drivers/net/hippi/ and make the necessary Kconfig and Makefile changes. CC: Jes Sorensen <jes@wildopensource.com> CC: Jes Sorensen <jes@trained-monkey.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* ppp: Move the PPP driversJeff Kirsher2011-08-271-168/+2
| | | | | | | | | | | | Move the PPP drivers into drivers/net/ppp/ and make the necessary Kconfig and Makefile changes. CC: Paul Mackerras <paulus@samba.org> CC: Frank Cusack <fcusack@fcusack.com> CC: Michal Ostrowski <mostrows@speakeasy.net> CC: Michal Ostrowski <mostrows@earthlink.net> CC: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* fddi: Move the FDDI driversJeff Kirsher2011-08-271-70/+2
| | | | | | | | | | Move the FDDI drivers into drivers/net/fddi/ and make the necessary Kconfig and Makefile changes. CC: "Maciej W. Rozycki" <macro@linux-mips.org> CC: Christoph Goos <cgoos@syskonnect.de> CC: <linux@syskonnect.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* net: Fix sungem_phy sharing.David S. Miller2011-08-161-0/+3
| | | | | | | | | | | Since sungem_phy is used by multiple, unrelated, drivers make it build as a real module under drivers/net. depmod will pick up the symbol dependency and make sure sungem_phy.ko gets loaded any time sungem.ko or spider_net.ko is loaded. Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: Kconfig and Makefile cleanupJeff Kirsher2011-08-131-116/+0
| | | | | | | | | | | | | | | After the move of the Ethernet drivers into drivers/net/ethernet/ there was some leftover cleanup to do in the Kconfig and Makefile. Removed the 10/100, 1000, and 10GbE Kconfig menus. Removed the out-dated pci-skeleton.c file which was used an example driver. With the current networking features and structure, the file is no longer a good example to use for driver creation. CC: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* tile: Move the Tilera driverJeff Kirsher2011-08-131-12/+0
| | | | | | | | | | Move the Tilera driver into drivers/net/ethernet/tile and make the necessary Kconfig and Makefile changes. Updated the Kconfig so that the options defualt to y if TILE kernel. CC: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* sh_eth: Move the Renesas SuperH driverJeff Kirsher2011-08-131-15/+0
| | | | | | | | Move the Renesas driver into drivers/net/ethernet/renesas/ and make the necessary Kconfig and Makefile changes. CC: Yoshihiro Shimoda <yoshihiro.shirmoda.uh@renesas.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* netx: Move the netx driverJeff Kirsher2011-08-131-10/+0
| | | | | | | | | Move the netx driver into drivers/net/ethernet/ and make the necessary Kconfig and Makefile changes. CC: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
* dm9000: Move the Davicom driverJeff Kirsher2011-08-131-28/+0
| | | | | | | | | | Move the Davicom driver into drivers/net/ethernet/davicom/ and make the necessary Kconfig and Makefile changes. CC: Ben Dooks <ben@simtec.co.uk> CC: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
* enc28j60: Move the Microchip driverJeff Kirsher2011-08-131-17/+0
| | | | | | | | Move the Microchip driver into drivers/net/ethernet/microchip/ and make the necessary Kconfig and Makefile changes. CC: Claudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* greth: Move the Aeroflex Gaisler driverJeff Kirsher2011-08-131-8/+0
| | | | | | | | Move the Aeroflex Gaisler driver into drivers/net/ethernet/aeroflex/ and make the necessary Kconfig and Makefile changes. CC: Kristoffer Glembo <kristoffer@gaisler.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* ethoc: Move the Avionic driverJeff Kirsher2011-08-131-10/+0
| | | | | | | | Move the Avionic driver into drivers/net/ethernet/ and make the necessary Kconfig and Makefile changes. CC: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* dnet: Move the Dave Ethernet driverJeff Kirsher2011-08-131-11/+0
| | | | | | | | Move the Dave Ethernet driver into drivers/net/ethernet/ and make the necessary Kconfig and Makefile changes. CC: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* hp100: Move the HP driverJeff Kirsher2011-08-131-11/+0
| | | | | | | | Move the HP driver into drivers/net/ethernet/hp/ and made the necessary Kconfig and Makefile changes. CC: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* starfire: Move the Adaptec driverJeff Kirsher2011-08-121-14/+0
| | | | | | | | Move the Adaptec driver into drivers/net/ethernet/adaptec/ and make the necessary Kconfig and Makefile changes. CC: Ion Badulescu <ionut@badula.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* forcedeth: Move the NVIDIA nForce driverJeff Kirsher2011-08-121-11/+0
| | | | | | | Move the nForce driver into drivers/net/ethernet/nvidia/ and make the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* fealnx: Move the Myson driverJeff Kirsher2011-08-121-9/+0
| | | | | | | | Move the Myson driver into drivers/net/ethernet/ and make the necessary Kconfig and Makefile changes. CC: Donald Becker <becker@scyld.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* r6040: Move the RDC driverJeff Kirsher2011-08-121-13/+0
| | | | | | | | Move the RDC driver into drivers/net/ethernet/rdc/ and make the necessary Kconfig and Makefile changes. CC: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>