summaryrefslogtreecommitdiffstats
path: root/drivers/net/bnx2.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* broadcom: Move the Broadcom driversJeff Kirsher2011-08-111-8607/+0
| | | | | | | | | | | | | Moves the drivers for Broadcom devices into drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile changes. CC: Eilon Greenstein <eilong@broadcom.com> CC: Michael Chan <mchan@broadcom.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Gary Zambrano <zambrano@broadcom.com> CC: "Maciej W. Rozycki" <macro@linux-mips.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* bnx2: Fix endian swapping on firmware version stringMichael Chan2011-07-211-3/+3
| | | | | | | | so that ethtool -i will display it correctly on big endian systems. Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Close device if tx_timeout reset failsMichael Chan2011-07-161-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on original patch and description from Flavio Leitner <fbl@redhat.com> When bnx2_reset_task() is called, it will stop, (re)initialize and start the interface to restore the working condition. The bnx2_init_nic() calls bnx2_reset_nic() which will reset the chip and then calls bnx2_free_skbs() to free all the skbs. The problem happens when bnx2_init_chip() fails because bnx2_reset_nic() will just return skipping the ring initializations at bnx2_init_all_rings(). Later, the reset task starts the interface again and the system crashes due a NULL pointer access (no skb in the ring). To fix it, we call dev_close() if bnx2_init_nic() fails. One minor wrinkle to deal with is the cancel_work_sync() call in bnx2_close() to cancel bnx2_reset_task(). The call will wait forever because it is trying to cancel itself and the workqueue will be stuck. Since bnx2_reset_task() holds the rtnl_lock() and checks for netif_running() before proceeding, there is no need to cancel bnx2_reset_task() in bnx2_close() even if bnx2_close() and bnx2_reset_task() are running concurrently. The rtnl_lock() serializes the 2 calls. We need to move the cancel_work_sync() call to bnx2_remove_one() to make sure it is canceled before freeing the netdev struct. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Read iSCSI config from shared memory during ->probe()Michael Chan2011-07-141-4/+9
| | | | | | | | | | | | The scratchpad location that we were reading from has not been initialized yet during ->probe(), so we were getting inaccurate information. Update version to 2.1.10. Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Add MCP dumpJeffrey Huang2011-07-141-13/+48
| | | | | | | | | to help debug issues related to management firmware. Signed-off-by: Jeffrey Huang <huangjw@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: remove unnecessary read of PCI_CAP_ID_EXPJon Mason2011-06-281-3/+2
| | | | | | | | | | | The PCIE capability offset is saved during PCI bus walking. It will remove an unnecessary search in the PCI configuration space if this value is referenced instead of reacquiring it. Also, pci_is_pcie is a better way of determining if the device is PCIE or not (as it uses the same saved PCIE capability offset). Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* cnic, bnx2: Check iSCSI support early in bnx2_init_one()Michael Chan2011-06-091-0/+7
| | | | | | | | | | | | | | | Based on earlier patch from Neil Horman <nhorman@tuxdriver.com> If iSCSI is not supported on a bnx2 device, bnx2_cnic_probe() will return NULL and the cnic device will not be visible to bnx2i. This will prevent bnx2i from registering and then unregistering during cnic_start() and cause the warning message: bnx2 0003:01:00.1: eth1: Failed waiting for ULP up call to complete Signed-off-by: Michael Chan <mchan@broadcom.com> Cc: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2011-05-051-0/+2
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/tg3.c
| * bnx2: cancel timer on device removalNeil Horman2011-04-291-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This oops was recently reported to me: invalid opcode: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:01.0/0000:01:0d.0/0000:02:05.0/device CPU 1 Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4 shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mod [last unloaded: bnx2] Modules linked in: bnx2(+) sunrpc ipv6 dm_mirror dm_region_hash dm_log sg microcode serio_raw amd64_edac_mod edac_core edac_mce_amd k8temp i2c_piix4 shpchp ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase scsi_transport_sas radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mod [last unloaded: bnx2] Pid: 23900, comm: pidof Not tainted 2.6.32-130.el6.x86_64 #1 BladeCenter LS21 -[797251Z]- RIP: 0010:[<ffffffffa058b270>] [<ffffffffa058b270>] 0xffffffffa058b270 RSP: 0018:ffff880002083e48 EFLAGS: 00010246 RAX: ffff880002083e90 RBX: ffff88007ccd4000 RCX: 0000000000000000 RDX: 0000000000000100 RSI: dead000000200200 RDI: ffff8800007b8700 RBP: ffff880002083ed0 R08: ffff88000208db40 R09: 0000022d191d27c8 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800007b9bc8 R13: ffff880002083e90 R14: ffff8800007b8700 R15: ffffffffa058b270 FS: 00007fbb3bcf7700(0000) GS:ffff880002080000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000001664a98 CR3: 0000000060395000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process pidof (pid: 23900, threadinfo ffff8800007e8000, task ffff8800091c0040) Stack: ffffffff81079f77 ffffffff8109e010 ffff88007ccd5c20 ffff88007ccd5820 <0> ffff88007ccd5420 ffff8800007e9fd8 ffff8800007e9fd8 0000010000000000 <0> ffff88007ccd5020 ffff880002083e90 ffff880002083e90 ffffffff8102a00d Call Trace: <IRQ> [<ffffffff81079f77>] ? run_timer_softirq+0x197/0x340 [<ffffffff8109e010>] ? tick_sched_timer+0x0/0xc0 [<ffffffff8102a00d>] ? lapic_next_event+0x1d/0x30 [<ffffffff8106f737>] __do_softirq+0xb7/0x1e0 [<ffffffff81092cc0>] ? hrtimer_interrupt+0x140/0x250 [<ffffffff81185f90>] ? filldir+0x0/0xe0 [<ffffffff8100c2cc>] call_softirq+0x1c/0x30 [<ffffffff8100df05>] do_softirq+0x65/0xa0 [<ffffffff8106f525>] irq_exit+0x85/0x90 [<ffffffff814e3340>] smp_apic_timer_interrupt+0x70/0x9b [<ffffffff8100bc93>] apic_timer_interrupt+0x13/0x20 <EOI> [<ffffffff81211ba5>] ? selinux_file_permission+0x45/0x150 [<ffffffff81262a75>] ? _atomic_dec_and_lock+0x55/0x80 [<ffffffff812050c6>] security_file_permission+0x16/0x20 [<ffffffff811861c1>] vfs_readdir+0x71/0xe0 [<ffffffff81186399>] sys_getdents+0x89/0xf0 [<ffffffff8100b172>] system_call_fastpath+0x16/0x1b It occured during some stress testing, in which the reporter was repeatedly removing and modprobing the bnx2 module while doing various other random operations on the bnx2 registered net device. Noting that this error occured on a serdes based device, we noted that there were a few ethtool operations (most notably self_test and set_phys_id) that have execution paths that lead into bnx2_setup_serdes_phy. This function is notable because it executes a mod_timer call, which starts the bp->timer running. Currently bnx2 is setup to assume that this timer only nees to be stopped when bnx2_close or bnx2_suspend is called. Since the above ethtool operations are not gated on the net device having been opened however, that assumption is incorrect, and can lead to the timer still running after the module has been removed, leading to the oops above (as well as other simmilar oopses). Fix the problem by ensuring that the timer is stopped when pci_device_unregister is called. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Hushan Jia <hjia@redhat.com> CC: Michael Chan <mchan@broadcom.com> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ethtool: cosmetic: Use ethtool ethtool_cmd_speed APIDavid Decotigny2011-04-291-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This updates the network drivers so that they don't access the ethtool_cmd::speed field directly, but use ethtool_cmd_speed() instead. For most of the drivers, these changes are purely cosmetic and don't fix any problem, such as for those 1GbE/10GbE drivers that indirectly call their own ethtool get_settings()/mii_ethtool_gset(). The changes are meant to enforce code consistency and provide robustness with future larger throughputs, at the expense of a few CPU cycles for each ethtool operation. All drivers compiled with make allyesconfig ion x86_64 have been updated. Tested: make allyesconfig on x86_64 + e1000e/bnx2x work Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ethtool: Use full 32 bit speed range in ethtool's set_settingsDavid Decotigny2011-04-291-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | This makes sure the ethtool's set_settings() callback of network drivers don't ignore the 16 most significant bits when ethtool calls their set_settings(). All drivers compiled with make allyesconfig on x86_64 have been updated. Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ethtool: allow custom interval for physical identificationAllan, Bruce W2011-04-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When physical identification of an adapter is done by toggling the mechanism on and off through software utilizing the set_phys_id operation, it is done with a fixed duration for both on and off states. Some drivers may want to set a custom duration for the on/off intervals. This patch changes the API so the return code from the driver's entry point when it is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to cycle the on/off states, and updates the drivers that have already been converted to use the new set_phys_id and use the synchronous method for identifying an adapter. The physical identification frequency set in the updated drivers is based on how it was done prior to the introduction of set_phys_id. Compile tested only. Also fixes a compiler warning in sfc. v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE v3: fold patchset into single patch and cleanup per Ben's feedback Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Cc: Michael Chan <mchan@broadcom.com> Cc: Eilon Greenstein <eilong@broadcom.com> Cc: Divy Le Ray <divy@chelsio.com> Cc: Don Fry <pcnet32@frontier.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com> Cc: Steve Hodgson <shodgson@solarflare.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Matt Carlson <mcarlson@broadcom.com> Acked-by: Jon Mason <jdmason@kudzu.us> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: bnx2: convert to hw_featuresMichał Mirosław2011-04-111-81/+28
| | | | | | | | | | Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2: convert to set_phys_idstephen hemminger2011-04-061-29/+27
|/ | | | | | | | In this case, need to add element to device private to hold original led state. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers net: Fix declaration ordering in inline functions.Balaji G2011-03-291-1/+1
| | | | | | | The correct usage should be "static inline void" instead of "static void inline" Signed-off-by: G.Balaji <balajig81@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update firmware and versionMichael Chan2011-03-141-4/+4
| | | | | | | | | | | Update 5709 mips firmware to 6.2.1a to fix iSCSI performance regression. There was an unnecessary context read in the fast path affecting performance. Update bnx2 to 2.1.6. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: remove some rcu sparse warningsEric Dumazet2011-01-281-2/+4
| | | | | | | | | | Add missing __rcu annotations and helpers. minor : Fix some rcu_dereference() calls in macvtap Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2011-01-271-8/+9
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
| * bnx2: Eliminate AER error messages on systems not supporting itMichael Chan2011-01-261-8/+9
| | | | | | | | | | | | | | | | | | | | | | On PPC for example, AER is not supported and we see unnecessary AER error message without this patch: bnx2 0003:01:00.1: pci_cleanup_aer_uncorrect_error_status failed 0xfffffffb Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'master' of ↵David S. Miller2011-01-261-0/+4
|\| | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
| * bnx2: Always set ETH_FLAG_TXVLANMichael Chan2011-01-251-0/+4
| | | | | | | | | | | | | | | | | | TSO does not work if the VLAN tag is in the packet (non-accelerated). We may be able to remove this restriction in future firmware. Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: change netdev->features to u32Michał Mirosław2011-01-251-1/+1
|/ | | | | | | | | | | | | Quoting Ben Hutchings: we presumably won't be defining features that can only be enabled on 64-bit architectures. Occurences found by `grep -r` on net/, drivers/net, include/ [ Move features and vlan_features next to each other in struct netdev, as per Eric Dumazet's suggestion -DaveM ] Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update firmware and versionMichael Chan2010-12-311-4/+4
| | | | | | | | | | Update MIPS firmware to 6.2.1, with improved small packet performance in RSS mode, and iSCSI CID allocation bug fix on 5708. Update driver version to 2.0.21. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Free IRQ before freeing status block memoryMichael Chan2010-12-311-1/+12
| | | | | | | | | | | | | When changing ring size, we free all memory including status block memory. If we're in INTA mode and sharing IRQ, the IRQ handler can be called and it will reference the NULL status block pointer. Because of the lockless design of the IRQ handler, there is no simple way to synchronize and prevent this. So we avoid this problem by freeing the IRQ handler before freeing the status block memory. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch '20101221_static_const' of git://repo.or.cz/linux-2.6/trivial-modsDavid S. Miller2010-12-211-22/+24
|\
| * drivers/net/*.c: Use static constJoe Perches2010-12-211-22/+24
| | | | | | | | | | | | | | Using static const generally increases object text and decreases data size. It also generally decreases overall object size. Signed-off-by: Joe Perches <joe@perches.com>
* | bnx2: remove cancel_work_sync() from remove_oneTejun Heo2010-12-211-2/+0
|/ | | | | | | | | | Michael pointed out that bnx2_close() already cancels bp->reset_task and thus it is guaranteed to be idle when bnx2_remove_one() is called. Remove the unnecessary cancel_work_sync() in remove_one. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: don't use flush_scheduled_work()Tejun Heo2010-12-121-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | flush_scheduled_work() is on its way out. This patch contains simple conversions to replace flush_scheduled_work() usage with direct cancels and flushes. Directly cancel the used works on driver detach and flush them in other cases. The conversions are mostly straight forward and the only dangers are, * Forgetting to cancel/flush one or more used works. * Cancelling when a work should be flushed (ie. the work must be executed once scheduled whether the driver is detaching or not). I've gone over the changes multiple times but it would be much appreciated if you can review with the above points in mind. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Michael Chan <mchan@broadcom.com> Cc: Divy Le Ray <divy@chelsio.com> Cc: e1000-devel@lists.sourceforge.net Cc: Vasanthy Kolluri <vkolluri@cisco.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Andrew Gallatin <gallatin@myri.com> Cc: Francois Romieu <romieu@fr.zoreil.com> Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com> Cc: Matt Carlson <mcarlson@broadcom.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Cc: netdev@vger.kernel.org
* bnx2: Remove config access to non-standard registersMichael Chan2010-11-281-8/+8
| | | | | | | | | | | In KVM passthrough mode, the driver may not have config access to non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register access to setup mailbox swapping can be done using MMIO. Update version to 2.0.20. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Fix reset bug on 5709Eddie Wai2010-11-281-7/+22
| | | | | | | | | | The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be cleared and polling for pending DMAs to complete before chip reset. Without this step, we've seen NMIs during repeated resets of the chip. Signed-off-by: Eddie Wai <waie@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: use vzalloc()Eric Dumazet2010-11-281-7/+2
| | | | | | | | Use vzalloc() and vzalloc_node() in net drivers Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.Jesse Gross2010-10-221-1/+1
| | | | | | | | | Some cards don't support changing vlan offloading settings. Make Ethtool set_flags return -EINVAL in those cases. Reported-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update bnx2 to use new vlan accleration.Jesse Gross2010-10-211-69/+28
| | | | | | | | Make the bnx2 driver use the new vlan accleration model. Signed-off-by: Jesse Gross <jesse@nicira.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vlan: Don't check for vlan group before vlan_tx_tag_present.Jesse Gross2010-10-211-1/+1
| | | | | | | | | | | | | Many (but not all) drivers check to see whether there is a vlan group configured before using a tag stored in the skb. There's not much point in this check since it just throws away data that should only be present in the expected circumstances. However, it will soon be legal and expected to get a vlan tag when no vlan group is configured, so remove this check from all drivers to avoid dropping the tags. Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Enable AER on PCIE devices onlyMichael Chan2010-10-121-14/+22
| | | | | | | | | | | | To prevent unnecessary error message. pci_save_state() is also moved to the end of ->probe() so that all PCI config, including AER state, will be saved. Update version to 2.0.18. Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update firmware to 6.0.x.Michael Chan2010-10-121-40/+25
| | | | | | | | | | | - Improved flow control and simplified interface - Use hardware RSS indirection table instead of the slower firmware- based table - Lower latency interrupt on 5709 Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Use netif_set_real_num_{rx,tx}_queues()Ben Hutchings2010-09-281-3/+6
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: return operator cleanupEric Dumazet2010-09-271-10/+10
| | | | | | | | | Change "return (EXPR);" to "return EXPR;" return is not a function, parentheses are not required. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: avoid some skb->ip_summed initializationsEric Dumazet2010-09-031-1/+1
| | | | | | | | | | | | | | | | | | | | fresh skbs have ip_summed set to CHECKSUM_NONE (0) We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers. Introduce skb_checksum_none_assert() helper so that we keep this assertion documented in driver sources. Change most occurrences of : skb->ip_summed = CHECKSUM_NONE; by : skb_checksum_none_assert(skb); Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Add PCI Advanced Error Reporting support.John Feeney2010-08-231-10/+34
| | | | | | | Signed-off-by: John Feeney <jfeeney@redhat.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update version to 2.0.17.Michael Chan2010-07-201-2/+2
| | | | | Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Remove some unnecessary smp_mb() in tx fast path.Michael Chan2010-07-201-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | smp_mb() inside bnx2_tx_avail() is used twice in the normal bnx2_start_xmit() path (see illustration below). The full memory barrier is only necessary during race conditions with tx completion. We can speed up the tx path by replacing smp_mb() in bnx2_tx_avail() with a compiler barrier. The compiler barrier is to force the compiler to fetch the tx_prod and tx_cons from memory. In the race condition between bnx2_start_xmit() and bnx2_tx_int(), we have the following situation: bnx2_start_xmit() bnx2_tx_int() if (!bnx2_tx_avail()) BUG(); ... if (!bnx2_tx_avail()) netif_tx_stop_queue(); update_tx_index(); smp_mb(); smp_mb(); if (bnx2_tx_avail()) if (netif_tx_queue_stopped() && netif_tx_wake_queue(); bnx2_tx_avail()) With smp_mb() removed from bnx2_tx_avail(), we need to add smp_mb() to bnx2_start_xmit() as shown above to properly order netif_tx_stop_queue() and bnx2_tx_avail() to check the ring index. If it is not strictly ordered, the tx queue can be stopped forever. This improves performance by about 5% with 2 ports running bi-directional 64-byte packets. Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Call pci_enable_msix() with actual number of vectors.Michael Chan2010-07-201-4/+20
| | | | | | | | | | | | | | Based on original patch by Breno Leitão <leitao@linux.vnet.ibm.com>. Allocate the actual number of vectors and make use of fewer vectors if pci_enable_msix() returns > 0. We must allocate one additional vector for the cnic driver. Cc: Breno Leitão <leitao@linux.vnet.ibm.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Use proper counter for net_device_stats->multicast.Michael Chan2010-07-201-1/+1
| | | | | | | | | | | We were using the wrong tx multicast counter instead of the rx multicast counter. Reported-by: Peter Snellman <peter.snellman@cinnober.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Reviewed-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: use device model DMA APIStanislaw Gruszka2010-07-181-53/+58
| | | | | | | | | Use DMA API as PCI equivalents will be deprecated. This change also allow to allocate with GFP_KERNEL in some places. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: allocate with GFP_KERNEL flag on RX path initStanislaw Gruszka2010-07-181-8/+9
| | | | | | Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: 64 bit stats on all archesEric Dumazet2010-07-091-18/+7
| | | | | | | | | | Now core network is able to handle 64 bit netdevice stats on 32 bit arches, we can provide them for bnx2, since hardware maintains some 64 bit counters. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update version to 2.0.16.Michael Chan2010-07-041-2/+2
| | | | | Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Dump some config space registers during TX timeout.Michael Chan2010-07-041-3/+8
| | | | | | | | These config register values will be useful when the memory registers are returning 0xffffffff which has been reported. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Add support for skb->rxhash.Michael Chan2010-07-041-1/+14
| | | | | | | | Add skb->rxhash support for TCP packets only because the bnx2 RSS hash does not hash UDP ports. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-16 01:56:53 +0100