summaryrefslogtreecommitdiffstats
path: root/drivers/net/bnx2x.h (follow)
Commit message (Collapse)AuthorAgeFilesLines
* bnx2x: Fix the maximal values of coalescing timeouts.Eilon Greenstein2009-07-061-0/+2
| | | | | | | | This patch properly defines the maximum values for rx/tx coalescing timeouts. Signed-off-by: Vlad Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Separated FW from the source.Vladislav Zolotarov2009-04-271-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | >From now on FW will be downloaded from the binary file using request_firmware. There will be different files for every supported chip. Currently 57710 (e1) and 57711 (e1h). File names have the following format: bnx2x-<chip version>-<FW version>.fw. ihex versions of current FW files are submitted in the next patch. Each binary file has a header in the following format: struct bnx2x_fw_file_section { __be32 len; __be32 offset; } struct bnx2x_fw_file_hdr { struct bnx2x_fw_file_section init_ops; struct bnx2x_fw_file_section init_ops_offsets; struct bnx2x_fw_file_section init_data; struct bnx2x_fw_file_section tsem_int_table_data; struct bnx2x_fw_file_section tsem_pram_data; struct bnx2x_fw_file_section usem_int_table_data; struct bnx2x_fw_file_section usem_pram_data; struct bnx2x_fw_file_section csem_int_table_data; struct bnx2x_fw_file_section csem_pram_data; struct bnx2x_fw_file_section xsem_int_table_data; struct bnx2x_fw_file_section xsem_pram_data; struct bnx2x_fw_file_section fw_version; } Each bnx2x_fw_file_section contains the length and the offset of the appropriate section in the binary file. Values are stored in the big endian format. Data types of arrays: init_data __be32 init_ops_offsets __be16 XXsem_pram_data u8 XXsem_int_table_data u8 init_ops struct raw_op { u8 op; __be24 offset; __be32 data; } fw_version u8 >From now boundaries of a specific initialization stage are stored in init_ops_offsets array instead of being defined by separate macroes. The index in init_ops_offsets is calculated by BLOCK_OPS_IDX macro: #define BLOCK_OPS_IDX(block, stage, end) \ (2*(((block)*STAGE_IDX_MAX) + (stage)) + (end)) Security: In addition to sanity check of array boundaries bnx2x will check a FW version. Additional checks might be added in the future. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-03-101-1/+1
|\ | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bnx2x_main.c drivers/net/wireless/iwlwifi/iwl3945-base.c drivers/net/wireless/rt2x00/rt73usb.c
| * bnx2x: Casting page alignmentEilon Greenstein2009-03-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Adding a proper cast to the argument of PAGE_ALIGN macro so that the output won't depend on its original type. Without this cast aligned value will be truncated to the size of the argument type. Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Clean-upEilon Greenstein2009-02-161-1/+1
| | | | | | | | | | | | | | | | Whitespaces, empty lines, 80 columns, indentations and removing redundant parenthesis Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Moving includesEilon Greenstein2009-02-161-0/+6
| | | | | | | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Sparse endianity annotationEilon Greenstein2009-02-161-11/+11
| | | | | | | | | | | | | | | | | | Resolving the majority of the issues, but there are still some left for future patches. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Removing redundant macrosEilon Greenstein2009-02-161-10/+0
| | | | | | | | | | | | Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Loopback in diag modeEilon Greenstein2009-02-161-4/+4
| | | | | | | | | | | | | | | | When loading in diag mode, set the device to loopback instead of normal link and then changing it to loopback mode Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Manual setting for MRRSEilon Greenstein2009-02-161-0/+1
| | | | | | | | | | | | | | Allows better debug capabilities if the user wants to force an MRRS value Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Using registers nameEilon Greenstein2009-02-161-3/+6
| | | | | | | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: PHY lock listEilon Greenstein2009-02-161-0/+1
| | | | | | | | | | | | | | | | | | Some dual port PHY require HW lock since they are used by both interfaces (different driver instances). Since this list is getting longer, update a parameter at load time instead of calculating it on runtime Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: GPIO accessoriesEilon Greenstein2009-02-161-0/+2
| | | | | | | | | | | | | | A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Removing redundant device parametersEilon Greenstein2009-02-161-5/+0
| | | | | | | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Removing the board typeEilon Greenstein2009-02-161-1/+0
| | | | | | | | | | | | | | | | There are too many different board types and this field is not scalable. Removing it and making decisions according to other fields Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Flow control enhancementEilon Greenstein2009-02-161-1/+1
| | | | | | | | | | | | | | | | | | Setting better HW thresholds and enabling FW capabilities for better enforcement. Also set the HW to more efficiently use the internal buffers if this is a single port design Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: BW shaper enhancementsEilon Greenstein2009-02-161-0/+3
| | | | | | | | | | | | | | | | | | Some of the configuration can be set when loading the device and shouldn't be re-calculated after each link up indication since it is not dependent on the link speed Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Per queue statisticsEilon Greenstein2009-02-161-10/+57
| | | | | | | | | | | | | | | | Re-ordering the statistics to enhance readability and adding per queue statistics (available via ethtool -S) Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Removing microcode assertion checkEilon Greenstein2009-02-161-1/+1
| | | | | | | | | | | | | | | | This check is unreliable since latest MC can issue warnings on rare occasions which are not fatal errors Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: System-page alignmentEilon Greenstein2009-02-161-2/+5
| | | | | | | | | | Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: MSI supportEilon Greenstein2009-02-161-1/+4
| | | | | | | | | | | | | | | | | | | | Enabling MSI on top of MSI-X and INTA. Also changing the module parameter to allow choosing INTA or MSI even when MSI-X is available. The default status block should not be reversed for endianity. Since MSI can issue re-configuration, the interrupt disable function now requires mmiowb Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: Multi-queueEilon Greenstein2009-02-161-11/+22
| | | | | | | | | | | | | | Adding Tx multi-queue and enabling multi-queue by default Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bnx2x: New FWEilon Greenstein2009-02-161-1/+1
|/ | | | | | | | | | | | | | | | This is the FW blob and the relevant definitions without any logic. It also contains the minimal mandatory code changes to work with this FW but it does not contain enabling of the new features that this FW provides. This FW is needed for: - More efficient multi-queue - per queue statistics - Big-endian issue with MSI - Improved pause response Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Version updateEilon Greenstein2009-01-201-1/+1
| | | | | | | Updating the version and the year of updated files Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Barriers for the compilerEilon Greenstein2009-01-201-8/+1
| | | | | | | | To make sure no swapping are made by the compiler, changed HAS_WORK to inline functions and added all the necessary barriers Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Fixing the doorbell sizeEilon Greenstein2009-01-151-1/+1
| | | | | | | | The size of the doorbell is 4KB, this bug become visible when using more than 8 queues Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: VLAN tagged packets without VLAN offloadEilon Greenstein2009-01-151-5/+7
| | | | | | | | Wrong handling of tagged packet if VLAN offload is disabled caused packets to get corrupted Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Using system page size for SGEEilon Greenstein2009-01-151-0/+3
| | | | | | | | | | | | When the page size is not 4KB, the FW must be programmed to work with the right SGE boundaries and fragment list length. To avoid confusion with the BCM_PAGE_SIZE which is set to 4KB for the FW sake, another alias for the system page size was added to explicitly indicate that it is meant for the SGE Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Using singlethread work queueEilon Greenstein2009-01-151-1/+1
| | | | | | | | | | | | | Since slow-path events, including link update, are handled in work-queue, a race condition was introduced in the self-test that sometimes caused the link status to fail: the self-test was running under RTNL lock, and if the link-watch was scheduled it stoped the shared work-queue (waiting for the RTNL lock) and so the link update event was not handled until the self-test ended (releasing the RTNL lock) with failure (since the link status was not updated) Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Accessing un-mapped pageEilon Greenstein2008-09-031-2/+3
| | | | | | | | | | | | | | | | The allocated RX buffer size was 64 bytes bigger than the PCI mapped size with no good reason. If the packet was actually using the buffer up to its limit and if the last 64 bytes of the buffer crossed 4KB boundary then an unmapped PCI page was accessed. The fix is to use only one parameter for the buffer size - there is no need to differentiate between the buffer size and the PCI mapping size since the extra 64 bytes can actually be used by the FW to align the Ethernet payload to 64 bytes. Also updating the driver version and date Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Rx work checkEilon Greenstein2008-08-261-1/+1
| | | | | | | | | | | | The has Rx work check was wrong: when the FW was at the end of the page, the driver was already at the beginning of the next page. Since the check only validated that both driver and FW are pointing to the same place, it concluded that there is still work to be done. This caused some serious issues including long latency results on ping-pong test and lockups while unloading the driver in that condition. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Checkpatch complianceEilon Greenstein2008-08-141-3/+3
| | | | | | | | | Checkpatch compliance The latest version of checkpatch found the following style errors in the code Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Spelling mistakesEilon Greenstein2008-08-141-5/+5
| | | | | | | | Spelling mistakes Spelling has to L's in it... Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Minor code improvementsEilon Greenstein2008-08-141-13/+10
| | | | | | | | | | | | | | | Minor code improvements Small changes to make the code a little bit more efficient and mostly more readable: - Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR - Removing the NIG_WR since it did nothing and was only confusing - On bnx2x_panic_dump, print only the used parts of the rings - define parameters only on the branch they are needed and not at the beginning of the function - using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: 1G LED does not turn offEilon Greenstein2008-08-141-0/+1
| | | | | | | | 1G LED does not turn off The 1G LED was not switched to off when the link was lost Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Change GPIO for any portEilon Greenstein2008-08-141-1/+1
| | | | | | | | | | Change GPIO for any port The set GPIO function should receive the port index to allow changing the GPIO of another port. This is needed for the common init phase (one the first driver is loaded for the chip) Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: HW attention lockEilon Greenstein2008-08-141-1/+0
| | | | | | | | | HW attention lock Making sure that only one function will handle the HW attention. This makes the device parameter aeu_mask redundant so it is removed Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Load/Unload under trafficVladislav Zolotarov2008-08-141-0/+9
| | | | | | | | | | | | | | | | | | | | | | | Load/Unload under traffic Few issues were found when loading and unloading under traffic: - When receiving Tx interrupt call netif_wake_queue if the queue is stopped but the state is open - Check that interrupts are enabled before doing anything else on the msix_fp_int function - In nic_load, enable the interrupts only when needed and ready for it - Function stop_leading returns status since it can fail - Add 1ms delay when unloading the driver to validate that there are no open transactions that already started by the FW - Splitting the "has work" function into Tx and Rx so the same function will be used on unload and interrupts - Do not request for WoL if only resetting the device (save the time that it takes the FW to set the link after reset) - Fixing the device reset after iSCSI boot and before driver load - all internal buffers must be cleared before the driver is loaded Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: StatisticsYitchak Gertner2008-08-141-4/+7
| | | | | | | | | | | | | | | | | Statistics - Making sure that each drop is accounted for in the driver statistics - Clearing the FW statistics when driver is loaded to prevent inconsistency with HW statistics - Once error is detected (bnx2x_panic_dump), stop the statistics before other actions (currently it is stopped last and can corrupt the data) - Adding HW checksum error counter to the statistics - Removing unused variable stats_ticks - Using macros instead of magic numbers to indicate which statistics are shared per port and which are per function Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Not dropping packets with L3/L4 checksum errorEilon Greenstein2008-08-141-8/+16
| | | | | | | | | Not dropping packets with L3/L4 checksum error Those packets should be passed to the OS. The problem is clear in forwarding mode. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Add TPA, Broadcoms HW LROVladislav Zolotarov2008-06-241-79/+197
| | | | | | | | | | | | | | | | | The TPA stands for Transparent Packet Aggregation. When enabled, the FW aggregate in-order TCP packets according to the 4-tuple match and sends 1 big packet to the driver. This packet is stored on an SGL in which each SGE is 1 page. The FW also implements a timeout algorithm and it honors all TCP flag, including the push flag as a trigger to halt aggregation. After receiving Ben Hutchings comments, we also added ethtool support, so now, thanks to Ben's patch, when forwarding is enabled, our aggregation is turned off using the LRO flags. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: New statistics codeYitchak Gertner2008-06-241-301/+200
| | | | | | | | | | To avoid race conditions with link up/down and driver up/down - the statistics handling was re-written in a form of state machine. Also supporting statistics for 57711 Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Add support for BCM57711 HWEilon Greenstein2008-06-241-302/+437
| | | | | | | | | | | | | | | Supporting the 57711 and 57711E - refers to in the code as E1H. The 57710 is referred to as E1. To support the new members in the family, the bnx2x structure was divided to 3 parts: common, port and function. These changes caused some rearrangement in the bnx2x.h file. A set of accessories macros were added to make access to the bnx2x structure more readable Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: New init infrastructureEilon Greenstein2008-06-241-25/+74
| | | | | | | | | | | | | | | | | | | This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: New link codeYaniv Rosner2008-06-241-155/+25
| | | | | | | | | | | | | | | | | | | | | | | | New Link code: Moving all the link related code (including the calculations, the initialization of the MAC and PHY and the external PHY's code) into a separated file. The changes from the code that used to be part of bnx2x.c (now called bnx2x_main.c) are: - Using separate structures for link inputs and link outputs to clearly identify what was configured and what is the outcome - Adding code to read external PHY FW version and print it as part of ethtool -i - Adding code to upgrade external PHY FW from ethtool -E with special magic number - Changing the link down indication to ERR level - Adding a lock on all PHY access to prevent an interrupt and setting changes to overlap - Adding support for emulation and FPGA (small chunk of code that really helps in the lab) - Adding support for 1G on BCM8706 PHY - Adding clear debug print incase of fan failure (the PHY type is now "failure") Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Updating the MaintainerEilon Greenstein2008-06-121-1/+2
| | | | | | | | | | I would like to thank Eliezer Tamir for writing and maintaining the driver for the past two years. I will take over maintaining the bnx2x driver from now on. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [BNX2X]: Fix Xmit bugsEliezer Tamir2008-02-281-0/+3
| | | | | | | | | Several endianity corrections in start_xmit() Fixed TSO bug where packets were missing the TCP flags. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [BNX2X]: fix slowpath races and lockingEliezer Tamir2008-02-281-3/+0
| | | | | | | | | | | | | | | | | | | Fixed locking between fastpath and slowpath operations. Corrected order of traffic disabling to prevent race when going down under traffic. - first have the microcode drop all incoming packets - then do the slowpath stuff - only then reset the MAC Got rid of in_reset_task. Remove_one() and friends would deference a null pointer if init_one failed. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [BNX2X]: correct statisticsEliezer Tamir2008-02-281-2/+2
| | | | | | | Errors were summed improperly, some stats were missing. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [BNX2X]: Correct RX filtering and MC configurationEliezer Tamir2008-02-281-4/+1
| | | | | | | | | | | | | | | The configuration of RX filtering needed the following corrections: Drop flags need to be set per Rx queue. Have to tell the microcode to collect drop stats, and properly wait for them to complete when going down. Sometimes we failed to detect proper completion due to a logical error in the wait loop. Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-21 12:27:55 +0100