summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: fec: Set mac_managed_pm during probeWei Fang2024-04-041-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Setting mac_managed_pm during interface up is too late. In situations where the link is not brought up yet and the system suspends the regular PHY power management will run. Since the FEC ETHEREN control bit is cleared (automatically) on suspend the controller is off in resume. When the regular PHY power management resume path runs in this context it will write to the MII_DATA register but nothing will be transmitted on the MDIO bus. This can be observed by the following log: fec 5b040000.ethernet eth0: MDIO read timeout Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110 Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110 The data written will however remain in the MII_DATA register. When the link later is set to administrative up it will trigger a call to fec_restart() which will restore the MII_SPEED register. This triggers the quirk explained in f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO") causing an extra MII_EVENT. This extra event desynchronizes all the MDIO register reads, causing them to complete too early. Leading all reads to read as 0 because fec_enet_mdio_wait() returns too early. When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes the PHY to be initialized incorrectly and the PHY will not transmit any ethernet signal in this state. It cannot be brought out of this state without a power cycle of the PHY. Fixes: 557d5dc83f68 ("net: fec: use mac-managed PHY PM") Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/ Signed-off-by: Wei Fang <wei.fang@nxp.com> [jernberg: commit message] Signed-off-by: John Ernberg <john.ernberg@actia.se> Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: Fixup EEEAndrew Lunn2024-03-061-18/+5
| | | | | | | | | | | | | | | | | | | | | | | | The enabling/disabling of EEE in the MAC should happen as a result of auto negotiation. So move the enable/disable into fec_enet_adjust_link() which gets called by phylib when there is a change in link status. fec_enet_set_eee() now just stores away the LPI timer value. Everything else is passed to phylib, so it can correctly setup the PHY. fec_enet_get_eee() relies on phylib doing most of the work, the MAC driver just adds the LPI timer value. Call phy_support_eee() if the quirk is present to indicate the MAC actually supports EEE. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> (On iMX8MP debix) Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Wei Fang <wei.fang@nxp.com> Link: https://lore.kernel.org/r/20240302195306.3207716-8-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: Move fec_enet_eee_mode_set() and helper earlierAndrew Lunn2024-03-061-37/+38
| | | | | | | | | | | | FEC is about to get its EEE code re-written. To allow this, move fec_enet_eee_mode_set() before fec_enet_adjust_link() which will need to call it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Wei Fang <wei.fang@nxp.com> Link: https://lore.kernel.org/r/20240302195306.3207716-7-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2024-02-291-9/+9
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cross-merge networking fixes after downstream PR. Conflicts: net/mptcp/protocol.c adf1bb78dab5 ("mptcp: fix snd_wnd initialization for passive socket") 9426ce476a70 ("mptcp: annotate lockless access for RX path fields") https://lore.kernel.org/all/20240228103048.19255709@canb.auug.org.au/ Adjacent changes: drivers/dpll/dpll_core.c 0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()") e7f8df0e81bf ("dpll: move xa_erase() call in to match dpll_pin_alloc() error path order") drivers/net/veth.c 1ce7d306ea63 ("veth: try harder when allocating queue memory") 0bef512012b1 ("net: add netdev_lockdep_set_classes() to virtual drivers") drivers/net/wireless/intel/iwlwifi/mvm/d3.c 8c9bef26e98b ("wifi: iwlwifi: mvm: d3: implement suspend with MLO") 78f65fbf421a ("wifi: iwlwifi: mvm: ensure offloading TID queue exists") net/wireless/nl80211.c f78c1375339a ("wifi: nl80211: reject iftype change with mesh ID change") 414532d8aa89 ("wifi: cfg80211: use IEEE80211_MAX_MESH_ID_LEN appropriately") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: dpaa: fman_memac: accept phy-interface-type = "10gbase-r" in the device ↵Vladimir Oltean2024-02-231-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tree Since commit 5d93cfcf7360 ("net: dpaa: Convert to phylink"), we support the "10gbase-r" phy-mode through a driver-based conversion of "xgmii", but we still don't actually support it when the device tree specifies "10gbase-r" proper. This is because boards such as LS1046A-RDB do not define pcs-handle-names (for whatever reason) in the ethernet@f0000 device tree node, and the code enters through this code path: err = of_property_match_string(mac_node, "pcs-handle-names", "xfi"); // code takes neither branch and falls through if (err >= 0) { (...) } else if (err != -EINVAL && err != -ENODATA) { goto _return_fm_mac_free; } (...) /* For compatibility, if pcs-handle-names is missing, we assume this * phy is the first one in pcsphy-handle */ err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii"); if (err == -EINVAL || err == -ENODATA) pcs = memac_pcs_create(mac_node, 0); // code takes this branch else if (err < 0) goto _return_fm_mac_free; else pcs = memac_pcs_create(mac_node, err); // A default PCS is created and saved in "pcs" // This determination fails and mistakenly saves the default PCS // memac->sgmii_pcs instead of memac->xfi_pcs, because at this // stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER. if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII) memac->xfi_pcs = pcs; else memac->sgmii_pcs = pcs; In other words, in the absence of pcs-handle-names, the default xfi_pcs assignment logic only works when in the device tree we have PHY_INTERFACE_MODE_XGMII. By reversing the order between the fallback xfi_pcs assignment and the "xgmii" overwrite with "10gbase-r", we are able to support both values in the device tree, with identical behavior. Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree conversion, because it would break forward compatibility (new device tree with old kernel). The only way to modify existing device trees to phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this value and handle it properly. One reason why the conversion is desirable is because with pre-phylink kernels, the Aquantia PHY driver used to warn about the improper use of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest) device tree that works with all supported stable kernel versions. Note that the blamed commit does not constitute a regression per se. Older stable kernels like 6.1 still do not work with "10gbase-r", but for a different reason. That is a battle for another time. [1] https://lore.kernel.org/netdev/20240214-ls1046-dts-use-10gbase-r-v1-1-8c2d68547393@concurrent-rt.com/ Fixes: 5d93cfcf7360 ("net: dpaa: Convert to phylink") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: Refactor: Replace FEC_ENET_FCE with FEC_RCR_FLOWCTLCsókás Bence2024-02-141-4/+2
| | | | | | | | | | | | | | | | | | | | FEC_ENET_FCE is the Flow Control Enable bit (bit 5) of the RCR. This is now defined as FEC_RCR_FLOWCTL. Signed-off-by: Csókás Bence <csokas.bence@prolan.hu> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240212153717.10023-2-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fec: Refactor: #define magic constantsCsókás Bence2024-02-141-16/+30
| | | | | | | | | | | | | | | | | | Add defines for bits of ECR, RCR control registers, TX watermark etc. Signed-off-by: Csókás Bence <csokas.bence@prolan.hu> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240212153717.10023-1-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fec: remove eee_enabled/eee_active in fec_enet_get_eee()Russell King (Oracle)2024-02-071-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fec_enet_get_eee() sets edata->eee_active and edata->eee_enabled from its own copy, and then calls phy_ethtool_get_eee() which in turn will call genphy_c45_ethtool_get_eee(). genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active with its own interpretation from the PHYs settings and negotiation result. Therefore, setting these members in fec_enet_get_eee() is redundant. Remove this, and remove the setting of fep->eee.eee_active member which becomes a write-only variable. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1rWbN2-002cCh-MY@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | ethtool: replace struct ethtool_eee with a new struct ethtool_keee on kernel ↵Heiner Kallweit2024-01-314-10/+10
|/ | | | | | | | | | | | | | | | | side In order to pass EEE link modes beyond bit 32 to userspace we have to complement the 32 bit bitmaps in struct ethtool_eee with linkmode bitmaps. Therefore, similar to ethtool_link_settings and ethtool_link_ksettings, add a struct ethtool_keee. In a first step it's an identical copy of ethtool_eee. This patch simply does a s/ethtool_eee/ethtool_keee/g for all users. No functional change intended. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: fix the unhandled context fault from smmuShenwei Wang2024-01-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | When repeatedly changing the interface link speed using the command below: ethtool -s eth0 speed 100 duplex full ethtool -s eth0 speed 1000 duplex full The following errors may sometimes be reported by the ARM SMMU driver: [ 5395.035364] fec 5b040000.ethernet eth0: Link is Down [ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault: fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2 [ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off It is identified that the FEC driver does not properly stop the TX queue during the link speed transitions, and this results in the invalid virtual I/O address translations from the SMMU and causes the context faults. Fixes: dbc64a8ea231 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
* net: fill in MODULE_DESCRIPTION()s for fsl_pq_mdioBreno Leitao2024-01-251-0/+1
| | | | | | | | | W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the Freescale PQ MDIO driver. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240123190332.677489-9-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fill in MODULE_DESCRIPTION()s for fecBreno Leitao2024-01-251-0/+1
| | | | | | | | | | W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the FEC (MPC8xx) Ethernet controller. Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Wei Fang <wei.fang@nxp.com> Link: https://lore.kernel.org/r/20240123190332.677489-8-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fill in MODULE_DESCRIPTION()s for enetcBreno Leitao2024-01-251-0/+1
| | | | | | | | | W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the NXP ENETC Ethernet driver. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240123190332.677489-7-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: enetc: allow phy-mode = "1000base-x"Vladimir Oltean2024-01-051-0/+3
| | | | | | | | | | | The driver code proper is handled by the lynx_pcs. The enetc just needs to populate phylink's supported_interfaces array, and return true for this phy-mode in enetc_port_has_pcs(), such that it creates an internal MDIO bus through which the Lynx PCS registers are accessed. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20240103113445.3892971-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* dpaa2-switch: cleanup the egress flood of an unused FDBIoana Ciornei2023-12-231-0/+6
| | | | | | | | | | | | | | | In case a DPAA2 switch interface joins a bridge, the FDB used on the port will be changed to the one associated with the bridge. What this means exactly is that any VLAN installed on the port will need to be removed and then installed back so that it points to the new FDB. Once this is done, the previous FDB will become unused (no VLAN to point to it). Even though no traffic will reach this FDB, it's best to just cleanup the state of the FDB by zeroing its egress flood domain. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: move a check to the prechangeupper stageIoana Ciornei2023-12-231-15/+16
| | | | | | | | | | | Two different DPAA2 switch ports from two different DPSW instances cannot be under the same bridge. Instead of checking for this unsupported configuration in the CHANGEUPPER event, check it as early as possible in the PRECHANGEUPPER one. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: reorganize the [pre]changeupper eventsIoana Ciornei2023-12-231-25/+52
| | | | | | | | | | | | | Create separate functions, dpaa2_switch_port_prechangeupper and dpaa2_switch_port_changeupper, to be called directly when a DPSW port changes its upper device. This way we are not open-coding everything in the main event callback and we can easily extent, for example, with bond offload. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: do not clear any interrupts automaticallyIoana Ciornei2023-12-231-2/+2
| | | | | | | | | | | | | | | | | | | | | | The DPSW object has multiple event sources multiplexed over the same IRQ. The driver has the capability to configure only some of these events to trigger the IRQ. The dpsw_get_irq_status() can clear events automatically based on the value stored in the 'status' variable passed to it. We don't want that to happen because we could get into a situation when we are clearing more events than we actually handled. Just resort to manually clearing the events that we handled. Also, since status is not used on the out path we remove its initialization to zero. This change does not have a user-visible effect because the dpaa2-switch driver enables and handles all the DPSW events which exist at the moment. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: add ENDPOINT_CHANGED to the irq_maskIoana Ciornei2023-12-231-1/+1
| | | | | | | | | | | | | | | | | | | | | Commit 84cba72956fd ("dpaa2-switch: integrate the MAC endpoint support") added support for MAC endpoints in the dpaa2-switch driver but omitted to add the ENDPOINT_CHANGED irq to the list of interrupt sources. Fix this by extending the list of events which can raise an interrupt by extending the mask passed to the dpsw_set_irq_mask() firmware API. There is no user visible impact even without this patch since whenever a switch interface is connected/disconnected from an endpoint both events are set (LINK_CHANGED and ENDPOINT_CHANGED) and, luckily, the LINK_CHANGED event could actually raise the interrupt and thus get the MAC/PHY SW configuration started. Even with this, it's better to just not rely on undocumented firmware behavior which can change. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: print an error when the vlan is already configuredIoana Ciornei2023-12-231-2/+4
| | | | | | | | | | Print a netdev error when we hit a case in which a specific VLAN is already configured on the port. While at it, change the already existing netdev_warn into an _err for consistency purposes. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: declare the netdev as IFF_LIVE_ADDR_CHANGE capableIoana Ciornei2023-12-231-0/+1
| | | | | | | | | | There is no restriction around the change of the MAC address on the switch ports, thus declare the interface netdevs IFF_LIVE_ADDR_CHANGE capable. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-switch: set interface MAC address only on endpoint changeIoana Ciornei2023-12-231-3/+2
| | | | | | | | | | | | | There is no point in updating the MAC address of a switch interface each time the link state changes, this only needs to happen in case the endpoint changes (the switch interface is [dis]connected from/to a MAC). Just move the call to dpaa2_switch_port_set_mac_addr() under DPSW_IRQ_EVENT_ENDPOINT_CHANGED. Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2023-12-153-28/+17
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/ethernet/intel/iavf/iavf_ethtool.c 3a0b5a2929fd ("iavf: Introduce new state machines for flow director") 95260816b489 ("iavf: use iavf_schedule_aq_request() helper") https://lore.kernel.org/all/84e12519-04dc-bd80-bc34-8cf50d7898ce@intel.com/ drivers/net/ethernet/broadcom/bnxt/bnxt.c c13e268c0768 ("bnxt_en: Fix HWTSTAMP_FILTER_ALL packet timestamp logic") c2f8063309da ("bnxt_en: Refactor RX VLAN acceleration logic.") a7445d69809f ("bnxt_en: Add support for new RX and TPA_START completion types for P7") 1c7fd6ee2fe4 ("bnxt_en: Rename some macros for the P5 chips") https://lore.kernel.org/all/20231211110022.27926ad9@canb.auug.org.au/ drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c bd6781c18cb5 ("bnxt_en: Fix wrong return value check in bnxt_close_nic()") 84793a499578 ("bnxt_en: Skip nic close/open when configuring tstamp filters") https://lore.kernel.org/all/20231214113041.3a0c003c@canb.auug.org.au/ drivers/net/ethernet/mellanox/mlx5/core/fw_reset.c 3d7a3f2612d7 ("net/mlx5: Nack sync reset request when HotPlug is enabled") cecf44ea1a1f ("net/mlx5: Allow sync reset flow when BF MGT interface device is present") https://lore.kernel.org/all/20231211110328.76c925af@canb.auug.org.au/ No adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * dpaa2-switch: do not ask for MDB, VLAN and FDB replayIoana Ciornei2023-12-141-9/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Starting with commit 4e51bf44a03a ("net: bridge: move the switchdev object replay helpers to "push" mode") the switchdev_bridge_port_offload() helper was extended with the intention to provide switchdev drivers easy access to object addition and deletion replays. This works by calling the replay helpers with non-NULL notifier blocks. In the same commit, the dpaa2-switch driver was updated so that it passes valid notifier blocks to the helper. At that moment, no regression was identified through testing. In the meantime, the blamed commit changed the behavior in terms of which ports get hit by the replay. Before this commit, only the initial port which identified itself as offloaded through switchdev_bridge_port_offload() got a replay of all port objects and FDBs. After this, the newly joining port will trigger a replay of objects on all bridge ports and on the bridge itself. This behavior leads to errors in dpaa2_switch_port_vlans_add() when a VLAN gets installed on the same interface multiple times. The intended mechanism to address this is to pass a non-NULL ctx to the switchdev_bridge_port_offload() helper and then check it against the port's private structure. But since the driver does not have any use for the replayed port objects and FDBs until it gains support for LAG offload, it's better to fix the issue by reverting the dpaa2-switch driver to not ask for replay. The pointers will be added back when we are prepared to ignore replays on unrelated ports. Fixes: b28d580e2939 ("net: bridge: switchdev: replay all VLAN groups") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20231212164326.2753457-3-ioana.ciornei@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * dpaa2-switch: fix size of the dma_unmapIoana Ciornei2023-12-141-3/+4
| | | | | | | | | | | | | | | | | | | | | | The size of the DMA unmap was wrongly put as a sizeof of a pointer. Change the value of the DMA unmap to be the actual macro used for the allocation and the DMA map. Fixes: 1110318d83e8 ("dpaa2-switch: add tc flower hardware offload on ingress traffic") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20231212164326.2753457-2-ioana.ciornei@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: fec: correct queue selectionRadu Bulie2023-12-101-16/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The old implementation extracted VLAN TCI info from the payload before the VLAN tag has been pushed in the payload. Another problem was that the VLAN TCI was extracted even if the packet did not have VLAN protocol header. This resulted in invalid VLAN TCI and as a consequence a random queue was computed. This patch fixes the above issues and use the VLAN TCI from the skb if it is present or VLAN TCI from payload if present. If no VLAN header is present queue 0 is selected. Fixes: 52c4a1a85f4b ("net: fec: add ndo_select_queue to fix TX bandwidth fluctuations") Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com> Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: ethtool: pass a pointer to parameters to get/set_rxfh ethtool opsAhmed Zaki2023-12-141-14/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters as direct function arguments. This will force us to change the API (and all drivers' functions) every time some new parameters are added. This is part 1/2 of the fix, as suggested in [1]: - First simplify the code by always providing a pointer to all params (indir, key and func); the fact that some of them may be NULL seems like a weird historic thing or a premature optimization. It will simplify the drivers if all pointers are always present. - Then make the functions take a dev pointer, and a pointer to a single struct wrapping all arguments. The set_* should also take an extack. Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1] Suggested-by: Jakub Kicinski <kuba@kernel.org> Suggested-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: Convert some ethtool_sprintf() to ethtool_puts()justinstitt@google.com2023-12-081-2/+2
|/ | | | | | | | | | | | | | | | | | | This patch converts some basic cases of ethtool_sprintf() to ethtool_puts(). The conversions are used in cases where ethtool_sprintf() was being used with just two arguments: | ethtool_sprintf(&data, buffer[i].name); or when it's used with format string: "%s" | ethtool_sprintf(&data, "%s", buffer[i].name); which both now become: | ethtool_puts(&data, buffer[i].name); Signed-off-by: Justin Stitt <justinstitt@google.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-eth: recycle the RX buffer only after all processing doneIoana Ciornei2023-11-261-2/+6
| | | | | | | | | | | | | | | | The blamed commit added support for Rx copybreak. This meant that for certain frame sizes, a new skb was allocated and the initial data buffer was recycled. Instead of waiting to recycle the Rx buffer only after all processing was done on it (like accessing the parse results or timestamp information), the code path just went ahead and re-used the buffer right away. This sometimes lead to corrupted HW and SW annotation areas. Fix this by delaying the moment when the buffer is recycled. Fixes: 50f826999a80 ("dpaa2-eth: add rx copybreak support") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* dpaa2-eth: increase the needed headroom to account for alignmentIoana Ciornei2023-11-262-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | Increase the needed headroom to account for a 64 byte alignment restriction which, with this patch, we make mandatory on the Tx path. The case in which the amount of headroom needed is not available is already handled by the driver which instead sends a S/G frame with the first buffer only holding the SW and HW annotation areas. Without this patch, we can empirically see data corruption happening between Tx and Tx confirmation which sometimes leads to the SW annotation area being overwritten. Since this is an old IP where the hardware team cannot help to understand the underlying behavior, we make the Tx alignment mandatory for all frames to avoid the crash on Tx conf. Also, remove the comment that suggested that this is just an optimization. This patch also sets the needed_headroom net device field to the usual value that the driver would need on the Tx path: - 64 bytes for the software annotation area - 64 bytes to account for a 64 byte aligned buffer address Fixes: 6e2387e8f19e ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver") Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/ Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: enetc: shorten enetc_setup_xdp_prog() error message to fit ↵Vladimir Oltean2023-11-081-1/+1
| | | | | | | | | | | | | | | | | | | | | NETLINK_MAX_FMTMSG_LEN NETLINK_MAX_FMTMSG_LEN is currently hardcoded to 80, and we provide an error printf-formatted string having 96 characters including the terminating \0. Assuming each %d (representing a queue) gets replaced by a number having at most 2 digits (a reasonable assumption), the final string is also 96 characters wide, which is too much. Reduce the verbiage a bit by removing some (partially) redundant words, which makes the new printf-formatted string be 73 characters wide with the trailing newline. Fixes: 800db2d125c2 ("net: enetc: ensure we always have a minimum number of TXQs for stack") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/lkml/202311061336.4dsWMT1h-lkp@intel.com/ Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20231106160311.616118-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge tag 'dma-mapping-6.7-2023-10-30' of ↵Linus Torvalds2023-11-021-10/+76
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.infradead.org/users/hch/dma-mapping Pull dma-mapping updates from Christoph Hellwig: - get rid of the fake support for coherent DMA allocation on coldfire with caches (Christoph Hellwig) - add a few Kconfig dependencies so that Kconfig catches the use of invalid configurations (Christoph Hellwig) - fix a type in dma-debug output (Chuck Lever) - rewrite a comment in swiotlb (Sean Christopherson) * tag 'dma-mapping-6.7-2023-10-30' of git://git.infradead.org/users/hch/dma-mapping: dma-debug: Fix a typo in a debugging eye-catcher swiotlb: rewrite comment explaining why the source is preserved on DMA_FROM_DEVICE m68k: remove unused includes from dma.c m68k: don't provide arch_dma_alloc for nommu/coldfire net: fec: use dma_alloc_noncoherent for data cache enabled coldfire m68k: use the coherent DMA code for coldfire without data cache dma-direct: warn when coherent allocations aren't supported dma-direct: simplify the use atomic pool logic in dma_direct_alloc dma-direct: add a CONFIG_ARCH_HAS_DMA_ALLOC symbol dma-direct: add dependencies to CONFIG_DMA_GLOBAL_POOL
| * net: fec: use dma_alloc_noncoherent for data cache enabled coldfireChristoph Hellwig2023-10-221-10/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Coldfire platforms with data caches can't properly implement dma_alloc_coherent and currently just return noncoherent memory from dma_alloc_coherent. The fec driver than works around this with a flush of all caches in the receive path. Make this hack a little less bad by using the explicit dma_alloc_noncoherent API and documenting the hacky cache flushes so that the DMA API level hack can be removed. Also replace the check for CONFIG_M532x for said hack with a check for COLDFIRE && !COLDFIRE_COHERENT_DMA. While m532x is the only such platform with a fec module, this makes the code more consistent and easier to follow. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Greg Ungerer <gerg@linux-m68k.org> Tested-by: Greg Ungerer <gerg@linux-m68k.org>
* | net: fec: Remove non-Coldfire platform IDsAlexander Stein2023-10-191-30/+0
| | | | | | | | | | | | | | | | | | | | | | All i.MX platforms (non-Coldfire) use DT nowadays, so their platform ID entries can be removed. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20231017063419.925266-3-alexander.stein@ew.tq-group.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fec: Fix device_get_match_data usageAlexander Stein2023-10-191-23/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | device_get_match_data() expects that of_device_id->data points to actual fec_devinfo data, not a platform_device_id entry. Fix this by adjusting OF device data pointers to their corresponding structs. enum imx_fec_type is now unused and can be removed. Fixes: b0377116decd ("net: ethernet: Use device_get_match_data()") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20231017063419.925266-2-alexander.stein@ew.tq-group.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fman: convert to .mac_get_caps()Russell King (Oracle)2023-10-181-6/+5
| | | | | | | | | | | | | | | | | | | | Convert fman to use the .mac_get_caps() method rather than the .validate() method. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Link: https://lore.kernel.org/r/E1qsPkA-009wid-Kv@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fec: replace deprecated strncpy with ethtool_sprintfJustin Stitt2023-10-131-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | `strncpy` is deprecated for use on NUL-terminated destination strings [1] and as such we should prefer more robust and less ambiguous string interfaces. ethtool_sprintf() is designed specifically for get_strings() usage. Let's replace strncpy in favor of this more robust and easier to understand interface. Also, while we're here, let's change memcpy() over to ethtool_sprintf() for consistency. Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1] Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2] Link: https://github.com/KSPP/linux/issues/90 Cc: linux-hardening@vger.kernel.org Signed-off-by: Justin Stitt <justinstitt@google.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: ethernet: Use device_get_match_data()Rob Herring2023-10-134-32/+20
| | | | | | | | | | | | | | | | | | Use preferred device_get_match_data() instead of of_match_device() to get the driver match data. With this, adjust the includes to explicitly include the correct headers. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Tree wide: Replace xdp_do_flush_map() with xdp_do_flush().Sebastian Andrzej Siewior2023-10-032-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | xdp_do_flush_map() is deprecated and new code should use xdp_do_flush() instead. Replace xdp_do_flush_map() with xdp_do_flush(). Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Clark Wang <xiaoning.wang@nxp.com> Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: David Arinzon <darinzon@amazon.com> Cc: Edward Cree <ecree.xilinx@gmail.com> Cc: Felix Fietkau <nbd@nbd.name> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Jassi Brar <jaswinder.singh@linaro.org> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: John Crispin <john@phrozen.org> Cc: Leon Romanovsky <leon@kernel.org> Cc: Lorenzo Bianconi <lorenzo@kernel.org> Cc: Louis Peens <louis.peens@corigine.com> Cc: Marcin Wojtas <mw@semihalf.com> Cc: Mark Lee <Mark-MC.Lee@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Noam Dagan <ndagan@amazon.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Saeed Bishara <saeedb@amazon.com> Cc: Saeed Mahameed <saeedm@nvidia.com> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Shay Agroskin <shayagr@amazon.com> Cc: Shenwei Wang <shenwei.wang@nxp.com> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Tony Nguyen <anthony.l.nguyen@intel.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Cc: Wei Fang <wei.fang@nxp.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Arthur Kiyanovski <akiyano@amazon.com> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: enetc: Annotate struct enetc_psfp_gate with __counted_byKees Cook2023-10-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Prepare for the coming implementation by GCC and Clang of the __counted_by attribute. Flexible array members annotated with __counted_by can have their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family functions). As found with Coccinelle[1], add __counted_by for struct enetc_psfp_gate. [1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20230922172858.3822653-11-keescook@chromium.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: enetc: Annotate struct enetc_int_vector with __counted_byKees Cook2023-10-021-1/+1
|/ | | | | | | | | | | | | | | | | | | Prepare for the coming implementation by GCC and Clang of the __counted_by attribute. Flexible array members annotated with __counted_by can have their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family functions). As found with Coccinelle[1], add __counted_by for struct enetc_int_vector. [1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20230922172858.3822653-5-keescook@chromium.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge tag 'net-6.6-rc1' of ↵Linus Torvalds2023-09-081-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking updates from Jakub Kicinski: "Including fixes from netfilter and bpf. Current release - regressions: - eth: stmmac: fix failure to probe without MAC interface specified Current release - new code bugs: - docs: netlink: fix missing classic_netlink doc reference Previous releases - regressions: - deal with integer overflows in kmalloc_reserve() - use sk_forward_alloc_get() in sk_get_meminfo() - bpf_sk_storage: fix the missing uncharge in sk_omem_alloc - fib: avoid warn splat in flow dissector after packet mangling - skb_segment: call zero copy functions before using skbuff frags - eth: sfc: check for zero length in EF10 RX prefix Previous releases - always broken: - af_unix: fix msg_controllen test in scm_pidfd_recv() for MSG_CMSG_COMPAT - xsk: fix xsk_build_skb() dereferencing possible ERR_PTR() - netfilter: - nft_exthdr: fix non-linear header modification - xt_u32, xt_sctp: validate user space input - nftables: exthdr: fix 4-byte stack OOB write - nfnetlink_osf: avoid OOB read - one more fix for the garbage collection work from last release - igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU - bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t - handshake: fix null-deref in handshake_nl_done_doit() - ip: ignore dst hint for multipath routes to ensure packets are hashed across the nexthops - phy: micrel: - correct bit assignments for cable test errata - disable EEE according to the KSZ9477 errata Misc: - docs/bpf: document compile-once-run-everywhere (CO-RE) relocations - Revert "net: macsec: preserve ingress frame ordering", it appears to have been developed against an older kernel, problem doesn't exist upstream" * tag 'net-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits) net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs() Revert "net: team: do not use dynamic lockdep key" net: hns3: remove GSO partial feature bit net: hns3: fix the port information display when sfp is absent net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue net: hns3: fix debugfs concurrency issue between kfree buffer and read net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read() net: hns3: Support query tx timeout threshold by debugfs net: hns3: fix tx timeout issue net: phy: Provide Module 4 KSZ9477 errata (DS80000754C) netfilter: nf_tables: Unbreak audit log reset netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID netfilter: nfnetlink_osf: avoid OOB read netfilter: nftables: exthdr: fix 4-byte stack OOB write selftests/bpf: Check bpf_sk_storage has uncharged sk_omem_alloc bpf: bpf_sk_storage: Fix the missing uncharge in sk_omem_alloc bpf: bpf_sk_storage: Fix invalid wait context lockdep report s390/bpf: Pass through tail call counter in trampolines ...
| * net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()Vladimir Oltean2023-09-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enetc_psi_create() returns an ERR_PTR() or a valid station interface pointer, but checking for the non-NULL quality of the return code blurs that difference away. So if enetc_psi_create() fails, we call enetc_psi_destroy() when we shouldn't. This will likely result in crashes, since enetc_psi_create() cleans up everything after itself when it returns an ERR_PTR(). Fixes: f0168042a212 ("net: enetc: reimplement RFS/RSS memory clearing as PCI quirk") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/netdev/582183ef-e03b-402b-8e2d-6d9bb3c83bd9@moroto.mountain/ Suggested-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230906141609.247579-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | Merge tag 'powerpc-6.6-1' of ↵Linus Torvalds2023-08-312-3/+0
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: - Add HOTPLUG_SMT support (/sys/devices/system/cpu/smt) and honour the configured SMT state when hotplugging CPUs into the system - Combine final TLB flush and lazy TLB mm shootdown IPIs when using the Radix MMU to avoid a broadcast TLBIE flush on exit - Drop the exclusion between ptrace/perf watchpoints, and drop the now unused associated arch hooks - Add support for the "nohlt" command line option to disable CPU idle - Add support for -fpatchable-function-entry for ftrace, with GCC >= 13.1 - Rework memory block size determination, and support 256MB size on systems with GPUs that have hotpluggable memory - Various other small features and fixes Thanks to Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Athira Rajeev, Benjamin Gray, Christophe Leroy, Frederic Barrat, Gautam Menghani, Geoff Levand, Hari Bathini, Immad Mir, Jialin Zhang, Joel Stanley, Jordan Niethe, Justin Stitt, Kajol Jain, Kees Cook, Krzysztof Kozlowski, Laurent Dufour, Liang He, Linus Walleij, Mahesh Salgaonkar, Masahiro Yamada, Michal Suchanek, Nageswara R Sastry, Nathan Chancellor, Nathan Lynch, Naveen N Rao, Nicholas Piggin, Nick Desaulniers, Omar Sandoval, Randy Dunlap, Reza Arbab, Rob Herring, Russell Currey, Sourabh Jain, Thomas Gleixner, Trevor Woerner, Uwe Kleine-König, Vaibhav Jain, Xiongfeng Wang, Yuan Tan, Zhang Rui, and Zheng Zengkai. * tag 'powerpc-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (135 commits) macintosh/ams: linux/platform_device.h is needed powerpc/xmon: Reapply "Relax frame size for clang" powerpc/mm/book3s64: Use 256M as the upper limit with coherent device memory attached powerpc/mm/book3s64: Fix build error with SPARSEMEM disabled powerpc/iommu: Fix notifiers being shared by PCI and VIO buses powerpc/mpc5xxx: Add missing fwnode_handle_put() powerpc/config: Disable SLAB_DEBUG_ON in skiroot powerpc/pseries: Remove unused hcall tracing instruction powerpc/pseries: Fix hcall tracepoints with JUMP_LABEL=n powerpc: dts: add missing space before { powerpc/eeh: Use pci_dev_id() to simplify the code powerpc/64s: Move CPU -mtune options into Kconfig powerpc/powermac: Fix unused function warning powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT powerpc: Don't include lppaca.h in paca.h powerpc/pseries: Move hcall_vphn() prototype into vphn.h powerpc/pseries: Move VPHN constants into vphn.h cxl: Drop unused detach_spa() powerpc: Drop zalloc_maybe_bootmem() powerpc/powernv: Use struct opal_prd_msg in more places ...
| * | powerpc/include: Remove mpc8260.h and m82xx_pci.hChristophe Leroy2023-08-161-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIU_INT_IRQ1 is not used anywhere and __IO_BASE is defined in asm/io.h Remove m82xx_pci.h Then the only thing remaining in mpc8260.h is MPC82XX_BCR_PLDP Move MPC82XX_BCR_PLDP into asm/cpm2.h then remove mpc8260.h Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/afe23bf3624c389ff17e9789884c78c124b7b202.1691474658.git.christophe.leroy@csgroup.eu
| * | powerpc/include: Remove unneeded #include <asm/fs_pd.h>Christophe Leroy2023-08-161-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tqm8xx_setup.c and fs_enet.h don't use any items provided by fs_pd.h Remove unneeded #include <asm/fs_pd.h> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/b056c4e986a4a7707fc1994304c34f7bd15d6871.1691474658.git.christophe.leroy@csgroup.eu
* | | Merge tag 'modules-6.6-rc1' of ↵Linus Torvalds2023-08-301-1/+1
|\ \ \ | |_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux Pull modules updates from Luis Chamberlain: "Summary of the changes worth highlighting from most interesting to boring below: - Christoph Hellwig's symbol_get() fix to Nvidia's efforts to circumvent the protection he put in place in year 2020 to prevent proprietary modules from using GPL only symbols, and also ensuring proprietary modules which export symbols grandfather their taint. That was done through year 2020 commit 262e6ae7081d ("modules: inherit TAINT_PROPRIETARY_MODULE"). Christoph's new fix is done by clarifing __symbol_get() was only ever intended to prevent module reference loops by Linux kernel modules and so making it only find symbols exported via EXPORT_SYMBOL_GPL(). The circumvention tactic used by Nvidia was to use symbol_get() to purposely swift through proprietary module symbols and completely bypass our traditional EXPORT_SYMBOL*() annotations and community agreed upon restrictions. A small set of preamble patches fix up a few symbols which just needed adjusting for this on two modules, the rtc ds1685 and the networking enetc module. Two other modules just needed some build fixing and removal of use of __symbol_get() as they can't ever be modular, as was done by Arnd on the ARM pxa module and Christoph did on the mmc au1xmmc driver. This is a good reminder to us that symbol_get() is just a hack to address things which should be fixed through Kconfig at build time as was done in the later patches, and so ultimately it should just go. - Extremely late minor fix for old module layout 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()") by James Morse for arm64. Note that this layout thing is old, it is *not* Song Liu's commit ac3b43283923 ("module: replace module_layout with module_memory"). The issue however is very odd to run into and so there was no hurry to get this in fast. - Although the fix did not go through the modules tree I'd like to highlight the fix by Peter Zijlstra in commit 54097309620e ("x86/static_call: Fix __static_call_fixup()") now merged in your tree which came out of what was originally suspected to be a fallout of the the newer module layout changes by Song Liu commit ac3b43283923 ("module: replace module_layout with module_memory") instead of module_init_section()"). Thanks to the report by Christian Bricart and the debugging by Song Liu & Peter that turned to be noted as a kernel regression in place since v5.19 through commit ee88d363d156 ("x86,static_call: Use alternative RET encoding"). I highlight this to reflect and clarify that we haven't seen more fallout from ac3b43283923 ("module: replace module_layout with module_memory"). - RISC-V toolchain got mapping symbol support which prefix symbols with "$" to help with alignment considerations for disassembly. This is used to differentiate between incompatible instruction encodings when disassembling. RISC-V just matches what ARM/AARCH64 did for alignment considerations and Palmer Dabbelt extended is_mapping_symbol() to accept these symbols for RISC-V. We already had support for this for all architectures but it also checked for the second character, the RISC-V check Dabbelt added was just for the "$". After a bit of testing and fallout on linux-next and based on feedback from Masahiro Yamada it was decided to simplify the check and treat the first char "$" as unique for all architectures, and so we no make is_mapping_symbol() for all archs if the symbol starts with "$". The most relevant commit for this for RISC-V on binutils was: https://sourceware.org/pipermail/binutils/2021-July/117350.html - A late fix by Andrea Righi (today) to make module zstd decompression use vmalloc() instead of kmalloc() to account for large compressed modules. I suspect we'll see similar things for other decompression algorithms soon. - samples/hw_breakpoint minor fixes by Rong Tao, Arnd Bergmann and Chen Jiahao" * tag 'modules-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: module/decompress: use vmalloc() for zstd decompression workspace kallsyms: Add more debug output for selftest ARM: module: Use module_init_layout_section() to spot init sections arm64: module: Use module_init_layout_section() to spot init sections module: Expose module_init_layout_section() modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules rtc: ds1685: use EXPORT_SYMBOL_GPL for ds1685_rtc_poweroff net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_index mmc: au1xmmc: force non-modular build and remove symbol_get usage ARM: pxa: remove use of symbol_get() samples/hw_breakpoint: mark sample_hbp as static samples/hw_breakpoint: fix building without module unloading samples/hw_breakpoint: Fix kernel BUG 'invalid opcode: 0000' modpost, kallsyms: Treat add '$'-prefixed symbols as mapping symbols kernel: params: Remove unnecessary ‘0’ values from err module: Ignore RISC-V mapping symbols too
| * | net: enetc: use EXPORT_SYMBOL_GPL for enetc_phc_indexChristoph Hellwig2023-08-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enetc_phc_index is only used via symbol_get, which was only ever intended for very internal symbols like this one. Use EXPORT_SYMBOL_GPL for it so that symbol_get can enforce only being used on EXPORT_SYMBOL_GPL symbols. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
* | | net: fec: add statistics for XDP_TXWei Fang2023-08-251-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The FEC driver supports the statistics for XDP actions except for XDP_TX before, because the XDP_TX was not supported when adding the statistics for XDP. Now the FEC driver has supported XDP_TX since commit f601899e4321 ("net: fec: add XDP_TX feature support"). So it's reasonable and necessary to add statistics for XDP_TX. Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: fec: add exception tracing for XDPWei Fang2023-08-241-15/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we already added the exception tracing for XDP_TX, I think it is necessary to add the exception tracing for other XDP actions, such as XDP_REDIRECT, XDP_ABORTED and unknown error actions. Signed-off-by: Wei Fang <wei.fang@nxp.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230822065255.606739-1-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-21 19:54:24 +0100