summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/myricom (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: remove napi_hash_del() from driver-facing APIJakub Kicinski2020-09-101-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We allow drivers to call napi_hash_del() before calling netif_napi_del() to batch RCU grace periods. This makes the API asymmetric and leaks internal implementation details. Soon we will want the grace period to protect more than just the NAPI hash table. Restructure the API and have drivers call a new function - __netif_napi_del() if they want to take care of RCU waits. Note that only core was checking the return status from napi_hash_del() so the new helper does not report if the NAPI was actually deleted. Some notes on driver oddness: - veth observed the grace period before calling netif_napi_del() but that should not matter - myri10ge observed normal RCU flavor - bnx2x and enic did not actually observe the grace period (unless they did so implicitly) - virtio_net and enic only unhashed Rx NAPIs The last two points seem to indicate that the calls to napi_hash_del() were a left over rather than an optimization. Regardless, it's easy enough to correct them. This patch may introduce extra synchronize_net() calls for interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on free_netdev() to call netif_napi_del(). This seems inevitable since we want to use RCU for netpoll dev->napi_list traversal, and almost no drivers set IFF_DISABLE_NETPOLL. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: myri10ge: use generic power managementVaibhav Gupta2020-07-211-29/+8
| | | | | | | | | | | | | | | | | | | | | | Drivers using legacy PM have to manage PCI states and device's PM states themselves. They also need to take care of configuration registers. With improved and powerful support of generic PM, PCI Core takes care of above mentioned, device-independent, jobs. This driver makes use of PCI helper functions like pci_save/restore_state(), pci_enable/disable_device(), pci_set_power_state() and pci_set_master() to do required operations. In generic mode, they are no longer needed. Change function parameter in both .suspend() and .resume() to "struct device*" type. Use to_pci_dev() and dev_get_drvdata() to get "struct pci_dev*" variable and drv data. Compile-tested only. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada2020-06-131-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
* myri10ge: Remove unused inline function myri10ge_vlan_ip_csumYueHaibing2020-05-051-12/+0
| | | | | | | | commit 4ca3221fe4b6 ("myri10ge: Convert from LRO to GRO") left behind this, remove it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: myri10ge: reject unsupported coalescing paramsJakub Kicinski2020-03-151-0/+1
| | | | | | | | | | Set ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters. This driver did not previously reject unsupported parameters. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: myri10ge: use skb_list_walk_safe helper for gso segmentsJason A. Donenfeld2020-01-091-5/+3
| | | | | | | | | This is a straight-forward conversion case for the new function, and while we're at it, we can remove a null write to skb->next by replacing it with skb_mark_not_on_list. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-08-191-1/+1
|\ | | | | | | | | | | | | Merge conflict of mlx5 resolved using instructions in merge commit 9566e650bf7fdf58384bb06df634f7531ca3a97e. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: myri10ge: fix memory leaksWenwen Wang2019-08-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices related structures. Later on, myri10ge_request_irq() is used to get an irq. However, if this process fails, the allocated slices related structures are not deallocated, leading to memory leaks. To fix this issue, revise the target label of the goto statement to 'abort_with_slices'. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
* | myri10ge: remove unneeded variableDing Xiang2019-07-311-2/+1
| | | | | | | | | | | | | | "error" is unneeded,just return 0 Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Use skb_frag_off accessorsJonathan Lemon2019-07-301-3/+3
| | | | | | | | | | | | | | | | Use accessor functions for skb fragment's page_offset instead of direct references, in preparation for bvec conversion. Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Use skb accessors in network driversMatthew Wilcox (Oracle)2019-07-231-5/+5
|/ | | | | | | | | In preparation for unifying the skb_frag and bio_vec, use the fine accessors which already exist and use skb_frag_t instead of struct skb_frag_struct. Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner2019-05-213-0/+3
| | | | | | | | | | | | | | Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* drivers: Remove explicit invocations of mmiowb()Will Deacon2019-04-081-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | mmiowb() is now implied by spin_unlock() on architectures that require it, so there is no reason to call it from driver code. This patch was generated using coccinelle: @mmiowb@ @@ - mmiowb(); and invoked as: $ for d in drivers include/linux/qed sound; do \ spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done NOTE: mmiowb() has only ever guaranteed ordering in conjunction with spin_unlock(). However, pairing each mmiowb() removal in this patch with the corresponding call to spin_unlock() is not at all trivial, so there is a small chance that this change may regress any drivers incorrectly relying on mmiowb() to order MMIO writes between CPUs using lock-free synchronisation. If you've ended up bisecting to this commit, you can reintroduce the mmiowb() calls using wmb() instead, which should restore the old behaviour on all architectures other than some esoteric ia64 systems. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
* net: myri10ge: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop ↵Yang Wei2019-02-141-1/+1
| | | | | | | | | | profiles dev_consume_skb_irq() should be called in myri10ge_tx_done() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
* cross-tree: phase out dma_zalloc_coherent()Luis Chamberlain2019-01-081-3/+3
| | | | | | | | | | | | | | | | | | | We already need to zero out memory for dma_alloc_coherent(), as such using dma_zalloc_coherent() is superflous. Phase it out. This change was generated with the following Coccinelle SmPL patch: @ replace_dma_zalloc_coherent @ expression dev, size, data, handle, flags; @@ -dma_zalloc_coherent(dev, size, handle, flags) +dma_alloc_coherent(dev, size, handle, flags) Suggested-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> [hch: re-ran the script on the latest tree] Signed-off-by: Christoph Hellwig <hch@lst.de>
* drivers: net: remove <net/busy_poll.h> inclusion when not neededEric Dumazet2018-10-261-1/+0
| | | | | | | | | | | | Drivers using generic NAPI interface no longer need to include <net/busy_poll.h>, since busy polling was moved to core networking stack long ago. See commit 79e7fff47b7b ("net: remove support for per driver ndo_busy_poll()") for reference. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: Use octal not symbolic permissionsJoe Perches2018-03-261-16/+16
| | | | | | | | | | | | | | Prefer the direct use of octal for permissions. Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace and some typing. Miscellanea: o Whitespace neatening around these conversions. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* treewide: setup_timer() -> timer_setup()Kees Cook2017-11-221-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
* License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-022-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* net: myricom: myri10ge: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes2017-02-131-13/+10
| | | | | | | | | | | | The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-by: Hyong-Youb Kim <hykim@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: get rid of custom busy poll codeEric Dumazet2017-02-031-193/+4
| | | | | | | | | | Compared to custom busy_poll, the generic NAPI one is simpler and removes a lot of code. It removes one atomic in the fast path (when busy poll is not in action) since we do not have to use an extra spinlock. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers: net: generalize napi_complete_done()Eric Dumazet2017-01-301-1/+1
| | | | | | | | | | | | napi_complete_done() allows to opt-in for gro_flush_timeout, added back in linux-3.19, commit 3b47d30396ba ("net: gro: add a per device gro flush timer") This allows for more efficient GRO aggregation without sacrifying latencies. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: make ndo_get_stats64 a void functionstephen hemminger2017-01-081-5/+4
| | | | | | | | | | | | The network device operation for reading statistics is only called in one place, and it ignores the return value. Having a structure return value is potentially confusing because some future driver could incorrectly assume that the return value was used. Fix all drivers with ndo_get_stats64 to have a void function. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: fix typo in parameter descriptionWei Yongjun2016-10-201-1/+1
| | | | | | | Fix typo in parameter description. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: use core min/max MTU checkingJarod Wilson2016-10-181-9/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | et131x: min_mtu 64, max_mtu 9216 altera_tse: min_mtu 64, max_mtu 1500 amd8111e: min_mtu 60, max_mtu 9000 bnad: min_mtu 46, max_mtu 9000 macb: min_mtu 68, max_mtu 1500 or 10240 depending on hardware capability xgmac: min_mtu 46, max_mtu 9000 cxgb2: min_mtu 68, max_mtu 9582 (pm3393) or 9600 (vsc7326) enic: min_mtu 68, max_mtu 9000 gianfar: min_mtu 50, max_mu 9586 hns_enet: min_mtu 68, max_mtu 9578 (v1) or 9706 (v2) ksz884x: min_mtu 60, max_mtu 1894 myri10ge: min_mtu 68, max_mtu 9000 natsemi: min_mtu 64, max_mtu 2024 nfp: min_mtu 68, max_mtu hardware-specific forcedeth: min_mtu 64, max_mtu 1500 or 9100, depending on hardware pch_gbe: min_mtu 46, max_mtu 10300 pasemi_mac: min_mtu 64, max_mtu 9000 qcaspi: min_mtu 46, max_mtu 1500 - remove qcaspi_netdev_change_mtu as it is now redundant rocker: min_mtu 68, max_mtu 9000 sxgbe: min_mtu 68, max_mtu 9000 stmmac: min_mtu 46, max_mtu depends on hardware tehuti: min_mtu 60, max_mtu 16384 - driver had no max mtu checking, but product docs say 16k jumbo packets are supported by the hardware netcp: min_mtu 68, max_mtu 9486 - remove netcp_ndo_change_mtu as it is now redundant via-velocity: min_mtu 64, max_mtu 9000 octeon: min_mtu 46, max_mtu 65370 CC: netdev@vger.kernel.org CC: Mark Einon <mark.einon@gmail.com> CC: Vince Bridgers <vbridger@opensource.altera.com> CC: Rasesh Mody <rasesh.mody@qlogic.com> CC: Nicolas Ferre <nicolas.ferre@atmel.com> CC: Santosh Raspatur <santosh@chelsio.com> CC: Hariprasad S <hariprasad@chelsio.com> CC: Christian Benvenuti <benve@cisco.com> CC: Sujith Sankar <ssujith@cisco.com> CC: Govindarajulu Varadarajan <_govind@gmx.com> CC: Neel Patel <neepatel@cisco.com> CC: Claudiu Manoil <claudiu.manoil@freescale.com> CC: Yisen Zhuang <yisen.zhuang@huawei.com> CC: Salil Mehta <salil.mehta@huawei.com> CC: Hyong-Youb Kim <hykim@myri.com> CC: Jakub Kicinski <jakub.kicinski@netronome.com> CC: Olof Johansson <olof@lixom.net> CC: Jiri Pirko <jiri@resnulli.us> CC: Byungho An <bh74.an@samsung.com> CC: Girish K S <ks.giri@samsung.com> CC: Vipul Pandya <vipul.pandya@samsung.com> CC: Giuseppe Cavallaro <peppe.cavallaro@st.com> CC: Alexandre Torgue <alexandre.torgue@st.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Wingman Kwok <w-kwok2@ti.com> CC: Murali Karicheri <m-karicheri2@ti.com> CC: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: fix sleeping with bh disabledStanislaw Gruszka2016-04-281-2/+2
| | | | | | | | | | | | | | | | | | | napi_disable() can not be called with bh disabled, move locking just around myri10ge_ss_lock_napi() . Patches fixes following bug: [ 114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383 <snip> [ 114.313712] Call Trace: [ 114.314943] [<ffffffff817010ce>] dump_stack+0x19/0x1b [ 114.317673] [<ffffffff810ce7f3>] __might_sleep+0x173/0x230 [ 114.320566] [<ffffffff815b3117>] napi_disable+0x27/0x90 [ 114.323254] [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge] Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Hyong-Youb Kim <hykim@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: provide generic busy polling to all NAPI driversEric Dumazet2015-11-181-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | NAPI drivers no longer need to observe a particular protocol to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y) napi_hash_add() and napi_hash_del() are automatically called from core networking stack, respectively from netif_napi_add() and netif_napi_del() This patch depends on free_netdev() and netif_napi_del() being called from process context, which seems to be the norm. Drivers might still prefer to call napi_hash_del() on their own, since they might combine all the rcu grace periods into a single one, knowing their NAPI structures lifetime, while core networking stack has no idea of a possible combining. Once this patch proves to not bring serious regressions, we will cleanup drivers to either remove napi_hash_del() or provide appropriate rcu grace periods combining. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: move skb_mark_napi_id() into core networking stackEric Dumazet2015-11-181-1/+1
| | | | | | | | | | | | | | | | We would like to automatically provide busy polling support to all NAPI drivers, without them having to implement anything. skb_mark_napi_id() can be called from napi_gro_receive() and napi_get_frags(). Few drivers are still calling skb_mark_napi_id() because they use netif_receive_skb(). They should eventually call napi_gro_receive() instead. I will leave this to drivers maintainers. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'modules-next-for-linus' of ↵Linus Torvalds2015-07-011-3/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux Pull module updates from Rusty Russell: "Main excitement here is Peter Zijlstra's lockless rbtree optimization to speed module address lookup. He found some abusers of the module lock doing that too. A little bit of parameter work here too; including Dan Streetman's breaking up the big param mutex so writing a parameter can load another module (yeah, really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were appended too" * tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits) modules: only use mod->param_lock if CONFIG_MODULES param: fix module param locks when !CONFIG_SYSFS. rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE() module: add per-module param_lock module: make perm const params: suppress unused variable error, warn once just in case code changes. modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'. kernel/module.c: avoid ifdefs for sig_enforce declaration kernel/workqueue.c: remove ifdefs over wq_power_efficient kernel/params.c: export param_ops_bool_enable_only kernel/params.c: generalize bool_enable_only kernel/module.c: use generic module param operaters for sig_enforce kernel/params: constify struct kernel_param_ops uses sysfs: tightened sysfs permission checks module: Rework module_addr_{min,max} module: Use __module_address() for module_address_lookup() module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING module: Optimize __module_address() using a latched RB-tree rbtree: Implement generic latch_tree seqlock: Introduce raw_read_seqcount_latch() ...
| * module: add per-module param_lockDan Streetman2015-06-231-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a "param_lock" mutex to each module, and update params.c to use the correct built-in or module mutex while locking kernel params. Remove the kparam_block_sysfs_r/w() macros, replace them with direct calls to kernel_param_[un]lock(module). The kernel param code currently uses a single mutex to protect modification of any and all kernel params. While this generally works, there is one specific problem with it; a module callback function cannot safely load another module, i.e. with request_module() or even with indirect calls such as crypto_has_alg(). If the module to be loaded has any of its params configured (e.g. with a /etc/modprobe.d/* config file), then the attempt will result in a deadlock between the first module param callback waiting for modprobe, and modprobe trying to lock the single kernel param mutex to set the new module's param. This fixes that by using per-module mutexes, so that each individual module is protected against concurrent changes in its own kernel params, but is not blocked by changes to other module params. All built-in modules continue to use the built-in mutex, since they will always be loaded at runtime and references (e.g. request_module(), crypto_has_alg()) to them will never cause load-time param changing. This also simplifies the interface used by modules to block sysfs access to their params; while there are currently functions to block and unblock sysfs param access which are split up by read and write and expect a single kernel param to be passed, their actual operation is identical and applies to all params, not just the one passed to them; they simply lock and unlock the global param mutex. They are replaced with direct calls to kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or if the module is built-in, it locks the built-in mutex. Suggested-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* | drivers/net: remove all references to obsolete Ethernet-HOWTOPaul Gortmaker2015-06-231-3/+1
|/ | | | | | | | | | | | | | | | | | This howto made sense in the 1990s when users had to manually configure ISA cards with jumpers or vendor utilities, but with the implementation of PCI it became increasingly less and less relevant, to the point where it has been well over a decade since I last updated it. And there is no value in anyone else taking over updating it either. However the references to it continue to spread as boiler plate text from one Kconfig file into the next. We are not doing end users any favours by pointing them at this old document, so lets kill it with fire, once and for all, to hopefully stop any further spread. No code is changed in this commit, just Kconfig help text. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: myri10ge: use arch_phys_wc_add()Luis R. Rodriguez2015-04-231-29/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | This driver already uses ioremap_wc() on the same range so when write-combining is available that will be used instead. Cc: Hyong-Youb Kim <hykim@myri.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Suresh Siddha <sbsiddha@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Juergen Gross <jgross@suse.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: netdev@vger.kernel.org Cc: Juergen Gross <jgross@suse.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Airlie <airlied@redhat.com> Cc: Antonino Daplas <adaplas@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: linux-kernel@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: Delete an unnecessary check before the function call "kfree"Markus Elfring2015-02-051-2/+1
| | | | | | | | | | The kfree() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: fix error return codeJulia Lawall2015-01-011-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> The patch also modifies the test of mgp->cmd to satisfy checkpatch. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: use eth_skb_pad helperAlexander Duyck2014-12-091-10/+5
| | | | | | | | | Update myri10ge to use eth_skb_pad helper. This also corrects a minor issue as the driver was updating length without updating the tail pointer. Cc: Hyong-Youb Kim <hykim@myri.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'pci-v3.17-changes-2' of ↵Linus Torvalds2014-08-151-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas: "Part two of the PCI changes for v3.17: - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine) It's a mechanical change that removes uses of the DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge window to reduce conflicts, but it's possible you'll still see a few" * tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
| * PCI: Remove DEFINE_PCI_DEVICE_TABLE macro useBenoit Taine2014-08-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to meet kernel coding style guidelines. This issue was reported by checkpatch. A simplified version of the semantic patch that makes this change is as follows (http://coccinelle.lip6.fr/): // <smpl> @@ identifier i; declarer name DEFINE_PCI_DEVICE_TABLE; initializer z; @@ - DEFINE_PCI_DEVICE_TABLE(i) + const struct pci_device_id i[] = z; // </smpl> [bhelgaas: add semantic patch] Signed-off-by: Benoit Taine <benoit.taine@lip6.fr> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* | myri10ge: check for DMA mapping errorsStanislaw Gruszka2014-08-141-30/+58
| | | | | | | | | | | | | | | | On IOMMU systems DMA mapping can fail, we need to check for that possibility. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing ↵Rickard Strandqvist2014-08-111-0/+1
|/ | | | | | | | | null-terminate after strncpy call Added a guaranteed null-terminate after call to strncpy. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: get rid of SET_ETHTOOL_OPSWilfried Klaebe2014-05-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | net: get rid of SET_ETHTOOL_OPS Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone. This does that. Mostly done via coccinelle script: @@ struct ethtool_ops *ops; struct net_device *dev; @@ - SET_ETHTOOL_OPS(dev, ops); + dev->ethtool_ops = ops; Compile tested only, but I'd seriously wonder if this broke anything. Suggested-by: Dave Miller <davem@davemloft.net> Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: Use pci_enable_msix_range() instead of pci_enable_msix()Alexander Gordeev2014-02-181-20/+20
| | | | | | | | | | | | | | As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() and pci_enable_msix_range() interfaces. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Hyong-Youb Kim <hykim@myri.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* net: myri10ge: remove unnecessary pci_set_drvdata()Jingoo Han2013-10-211-1/+0
| | | | | | | | | The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: myri10ge: Change variable type to boolPeter Senna Tschudin2013-10-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | | There is the rc variable on both myri10ge_ss_lock_napi and myri10ge_ss_lock_poll functions. In both cases rc is only assigned the values true and false. Both functions already return bool. Change rc type to bool. The simplified semantic patch that find this problem is as follows (http://coccinelle.lip6.fr/): @exists@ type T; identifier b; @@ - T + bool b = ...; ... when any b = \(true\|false\) Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net:drivers/net: Miscellaneous conversions to ETH_ALENJoe Perches2013-10-021-2/+2
| | | | | | | | | | | | Convert the memset/memcpy uses of 6 to ETH_ALEN where appropriate. Also convert some struct definitions and u8 array declarations of [6] to ETH_ALEN. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers:net: Convert dma_alloc_coherent(...__GFP_ZERO) to dma_zalloc_coherentJoe Perches2013-08-301-3/+3
| | | | | | | | | | | | | | | | | | | | | __GFP_ZERO is an uncommon flag and perhaps is better not used. static inline dma_zalloc_coherent exists so convert the uses of dma_alloc_coherent with __GFP_ZERO to the more common kernel style with zalloc. Remove memset from the static inline dma_zalloc_coherent and add just one use of __GFP_ZERO instead. Trivially reduces the size of the existing uses of dma_zalloc_coherent. Realign arguments as appropriate. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: Add support for ndo_busy_pollHyong-Youb Kim2013-08-211-2/+198
| | | | | | | | | | | | | Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive packets with the napi id. For each slice, use per-slice spinlock and state variable to ensure that only one handler processes receive pacekts. Locking, statistics counters, and the ndo_busy_poll handler follow those in the ixgbe driver. So, credit goes to that driver's authors. Signed-off-by: Hyong-Youb Kim <hykim@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* myri10ge: clean up unnecessary MSI/MSI-X capability findYijing Wang2013-08-091-3/+2
| | | | | | | | | | | | | | PCI core will initialize device MSI/MSI-X capability in pci_msi_init_pci_dev(). So device driver should use pci_dev->msi_cap/msix_cap to determine whether the device support MSI/MSI-X instead of using pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX). Access to PCIe device config space again will consume more time. Signed-off-by: Yijing Wang <wangyijing@huawei.com> Cc: Andrew Gallatin <gallatin@myri.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: Convert mac address uses of 6 to ETH_ALENJoe Perches2013-08-021-1/+1
| | | | | | | | | | | | Use the normal #define to help grep find mac addresses and ensure that addresses are aligned. pasemi.h has an unaligned access to mac_addr, unchanged for now. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Olof Johansson <olof@lixom.net> # pasemi_mac pieces Signed-off-by: David S. Miller <davem@davemloft.net>
* net/trivial: replace numeric with standard PM state macrosYijing Wang2013-06-291-1/+1
| | | | | | | | | Use standard PM state macros PCI_Dx instead of numeric 0/1/2.. Signed-off-by: Yijing Wang <wangyijing@huawei.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* net: vlan: add protocol argument to packet tagging functionsPatrick McHardy2013-04-191-1/+1
| | | | | | | | | | Add a protocol argument to the VLAN packet tagging functions. In case of HW tagging, we need that protocol available in the ndo_start_xmit functions, so it is stored in a new field in the skb. The new field fits into a hole (on 64 bit) and doesn't increase the sks's size. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-25 08:17:21 +0100