| Commit message (Collapse) | Author | Files | Lines |
|---|
|
After the packet is successfully sent, we should not touch the packet
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
THREAD 1 THREAD 2
======== ========
team_notify_peers(teamX)
atomic_set count_pending = 1
schedule_delayed_work
team_notify_peers(teamX)
atomic_set count_pending = 1
team_notify_peers_work
atomic_dec_and_test
count_pending = 0
(return)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test
count_pending = -1
schedule_delayed_work
(repeat until count_pending = 0)
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Fixes: fc423ff00df3a19554414ee ("team: add peer notification")
Fixes: 492b200efdd20b8fcfdac87 ("team: add support for sending multicast rejoins")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The result of a negated container has to be inverted before checking for
early ending.
This fixes my previous attempt (17c9c8232663a47f074b7452b9b034efda868ca7) to
make inverted containers work correctly.
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit bc23333ba11fb7f959b7e87e121122f5a0fbbca8 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb4b8 ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resume the device before setting the MAC address.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
ifconfig eth0 down
ethtool -s eth0 autoneg off speed 10 duplex half
ifconfig eth0 up
Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I got a report of a double free happening at RDS slab cache. One
suspicion was that may be somewhere we were doing a sock_hold/sock_put
on an already freed sock. Thus after providing a kernel with the
following change:
static inline void sock_hold(struct sock *sk)
{
- atomic_inc(&sk->sk_refcnt);
+ if (!atomic_inc_not_zero(&sk->sk_refcnt))
+ WARN(1, "Trying to hold sock already gone: %p (family: %hd)\n",
+ sk, sk->sk_family);
}
The warning successfuly triggered:
Trying to hold sock already gone: ffff81f6dda61280 (family: 21)
WARNING: at include/net/sock.h:350 sock_hold()
Call Trace:
<IRQ> [<ffffffff8adac135>] :rds:rds_send_remove_from_sock+0xf0/0x21b
[<ffffffff8adad35c>] :rds:rds_send_drop_acked+0xbf/0xcf
[<ffffffff8addf546>] :rds_rdma:rds_ib_recv_tasklet_fn+0x256/0x2dc
[<ffffffff8009899a>] tasklet_action+0x8f/0x12b
[<ffffffff800125a2>] __do_softirq+0x89/0x133
[<ffffffff8005f30c>] call_softirq+0x1c/0x28
[<ffffffff8006e644>] do_softirq+0x2c/0x7d
[<ffffffff8006e4d4>] do_IRQ+0xee/0xf7
[<ffffffff8005e625>] ret_from_intr+0x0/0xa
<EOI>
Looking at the call chain above, the only way I think this would be
possible is if somewhere we already released the same socket->sock which
is assigned to the rds_message at rds_send_remove_from_sock. Which seems
only possible to happen after the tear down done on rds_release.
rds_release properly calls rds_send_drop_to to drop the socket from any
rds_message, and some proper synchronization is in place to avoid race
with rds_send_drop_acked/rds_send_remove_from_sock. However, I still see
a very narrow window where it may be possible we touch a sock already
released: when rds_release races with rds_send_drop_acked, we check
RDS_MSG_ON_CONN to avoid cleanup on the same rds_message, but in this
specific case we don't clear rm->m_rs. In this case, it seems we could
then go on at rds_send_drop_to and after it returns, the sock is freed
by last sock_put on rds_release, with concurrently we being at
rds_send_remove_from_sock; then at some point in the loop at
rds_send_remove_from_sock we process an rds_message which didn't have
rm->m_rs unset for a freed sock, and a possible sock_hold on an sock
already gone at rds_release happens.
This hopefully address the described condition above and avoids a double
free on "second last" sock_put. In addition, I removed the comment about
socket destruction on top of rds_send_drop_acked: we call rds_send_drop_to
in rds_release and we should have things properly serialized there, thus
I can't see the comment being accurate there.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I see two problems if we consider the sock->ops->connect attempt to fail in
rds_tcp_conn_connect. The first issue is that for example we don't remove the
previously added rds_tcp_connection item to rds_tcp_tc_list at
rds_tcp_set_callbacks, which means that on a next reconnect attempt for the
same rds_connection, when rds_tcp_conn_connect is called we can again call
rds_tcp_set_callbacks, resulting in duplicated items on rds_tcp_tc_list,
leading to list corruption: to avoid this just make sure we call
properly rds_tcp_restore_callbacks before we exit. The second issue
is that we should also release the sock properly, by setting sock = NULL
only if we are returning without error.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zone allocation batches can easily underflow due to higher-order
allocations or spills to remote nodes. On SMP that's fine, because
underflows are expected from concurrency and dealt with by returning 0.
But on UP, zone_page_state will just return a wrapped unsigned long,
which will get past the <= 0 check and then consider the zone eligible
until its watermarks are hit.
Commit 3a025760fc15 ("mm: page_alloc: spill to remote nodes before
waking kswapd") already made the counter-resetting use
atomic_long_read() to accomodate underflows from remote spills, but it
didn't go all the way with it.
Make it clear that these batches are expected to go negative regardless
of concurrency, and use atomic_long_read() everywhere.
Fixes: 81c0a2bb515f ("mm: page_alloc: fair zone allocator policy")
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Oleg noticed that a cleanup by Sylvain actually uncovered a bug; by
calling perf_event_free_task() when failing sched_fork() we will not yet
have done the memset() on ->perf_event_ctxp[] and will therefore try and
'free' the inherited contexts, which are still in use by the parent
process. This is bad..
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Sylvain 'ythier' Hitier <sylvain.hitier@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The repository for mpc5xxx has been moved, update git URL to new
location.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The cgroup iterators yield css objects that have not yet gone through
css_online(), but they are not complete memcgs at this point and so the
memcg iterators should not return them. Commit d8ad30559715 ("mm/memcg:
iteration skip memcgs not yet fully initialized") set out to implement
exactly this, but it uses CSS_ONLINE, a cgroup-internal flag that does
not meet the ordering requirements for memcg, and so the iterator may
skip over initialized groups, or return partially initialized memcgs.
The cgroup core can not reasonably provide a clear answer on whether the
object around the css has been fully initialized, as that depends on
controller-specific locking and lifetime rules. Thus, introduce a
memcg-specific flag that is set after the memcg has been initialized in
css_online(), and read before mem_cgroup_iter() callers access the memcg
members.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In dlm_assert_master_handler, the mle is get in dlm_find_mle, should be
put when goto kill, otherwise, this mle will never be released.
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch reverts 1ba6e0b50b ("mm: numa: split_huge_page: transfer the
NUMA type from the pmd to the pte"). If a huge page is being split due
a protection change and the tail will be in a PROT_NONE vma then NUMA
hinting PTEs are temporarily created in the protected VMA.
VM_RW|VM_PROTNONE
|-----------------|
^
split here
In the specific case above, it should get fixed up by change_pte_range()
but there is a window of opportunity for weirdness to happen. Similarly,
if a huge page is shrunk and split during a protection update but before
pmd_numa is cleared then a pte_numa can be left behind.
Instead of adding complexity trying to deal with the case, this patch
will not mark PTEs NUMA when splitting a huge page. NUMA hinting faults
will not be triggered which is marginal in comparison to the complexity
in dealing with the corner cases during THP split.
Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A migration entry is marked as write if pte_write was true at the time the
entry was created. The VMA protections are not double checked when migration
entries are being removed as mprotect marks write-migration-entries as
read. It means that potentially we take a spurious fault to mark PTEs write
again but it's straight-forward. However, there is a race between write
migrations being marked read and migrations finishing. This potentially
allows a PTE to be write that should have been read. Close this race by
double checking the VMA permissions using maybe_mkwrite when migration
completes.
[torvalds@linux-foundation.org: use maybe_mkwrite]
Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <shli@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Cc: stable@vger.kernel.org (3.7+)
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 620125f2bf8ff0c4969b79653b54d7bcc9d40637
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Linus commit 05c63c2ff23a80b654d6c088ac3ba21628db0173 modified the
runtime suspend/resume paths to skip over display-related tasks to
avoid locking issues on resume.
Unfortunately, this resulted in the display hardware being left in
a partially initialised state, preventing subsequent modesets from
completing.
This commit unifies the (many) suspend/resume paths, bringing back
display (and fbcon) handling in the runtime paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Preparation for some runtime pm fixes. Currently we skip over fbcon
suspend/resume in the runtime path, which causes issues on resume if
fbcon tries to write to the framebuffer before the BAR subdev has
been resumed to restore the BAR1 VM setup.
As we might be woken up via a sysfs connector, we are unable to call
fb_set_suspend() in the resume path as it could make its way down to
a modeset and cause all sorts of locking hilarity.
To solve this, we'll just delay the fbcon resume to a workqueue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Xorg (and any non-DRM client really) doesn't have permission to directly
touch VRAM on nv50 and up, which the fence code prior to g84 depends on.
It's less invasive to temporarily grant it premission to do so, as it
previously did, than it is to rework fencenv50 to use the VM. That
will come later on.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Reported in fdo#82527 comment #2.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Update the maintainer email for BNA driver.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the serial console on machines where the serial port is located on
the SuperIO chip.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
|
|
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The calculation of page_ptr here is wrong in the case the read doesn't
start at an offset that is a multiple of a page.
The result is that nfs4svc_encode_compoundres sets rq_next_page to a
value one too small, and then the loop in svc_free_res_pages may
incorrectly fail to clear a page pointer in rq_respages[].
Pages left in rq_respages[] are available for the next rpc request to
use, so xdr data may be written to that page, which may hold data still
waiting to be transmitted to the client or data in the page cache.
The observed result was silent data corruption seen on an NFSv4 client.
We tag this as "fixing" 05638dc73af2 because that commit exposed this
bug, though the incorrect calculation predates it.
Particular thanks to Andrea Arcangeli and David Gilbert for analysis and
testing.
Fixes: 05638dc73af2 "nfsd4: simplify server xdr->next_page use"
Cc: stable@vger.kernel.org
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Commit 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
introduced a bug where the governors wouldn't be stopped anymore for
->target{_index}() drivers during suspend. This happens because
'cpufreq_suspended' is updated before stopping the governors during suspend
and due to this __cpufreq_governor() would return early due to this check:
/* Don't start any governor operations if we are entering suspend */
if (cpufreq_suspended)
return 0;
Fixes: 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 8e30444e1530 "cpufreq: fix cpufreq suspend/resume for intel_pstate"
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When compiling kprobes-test-arm.c the following error has been observed
/tmp/ccoT403o.s:21439: Error: bad immediate value for offset (4168)
This is caused by the compiler spilling it's literal pool too far away
from the site which is trying to reference it with a PC relative load.
This arises because the compiler is underestimating the size of the
inline assembler code present, which apparently it approximates as 4
bytes per line or instruction.
We fix this problem by moving the operations which generate more than
4 bytes out of the text section. Specifically, moving the .ascii
directives to the .rodata section.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Joachim Eastwood reports that commit fbfb872f5f41 "ARM: 8148/1: flush
TLS and thumbee register state during exec" causes a boot-time crash
on a Cortex-M4 nommu system:
Freeing unused kernel memory: 68K (281e5000 - 281f6000)
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
task: 29834000 ti: 29832000 task.ti: 29832000
PC is at flush_thread+0x2e/0x40
LR is at flush_thread+0x21/0x40
pc : [<2800954a>] lr : [<2800953d>] psr: 4100000b
sp : 29833d60 ip : 00000000 fp : 00000001
r10: 00003cf8 r9 : 29b1f000 r8 : 00000000
r7 : 29b0bc00 r6 : 29834000 r5 : 29832000 r4 : 29832000
r3 : ffff0ff0 r2 : 29832000 r1 : 00000000 r0 : 282121f0
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
[<2800afa5>] (unwind_backtrace) from [<2800a327>] (show_stack+0xb/0xc)
[<2800a327>] (show_stack) from [<2800a963>] (__invalid_entry+0x4b/0x4c)
The problem is that set_tls is attempting to clear the TLS location in
the kernel-user helper page, which isn't set up on V7M.
Fix this by guarding the write to the kuser helper page with
a CONFIG_KUSER_HELPERS ifdef.
Fixes: fbfb872f5f41 ARM: 8148/1: flush TLS and thumbee register state during exec
Reported-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
on ARMv6
This fixes build breakage of platsmp.c if ARMv6 was chosen for compile
time options (e.g. by building allmodconfig):
$ make allmodconfig
$ make
CC arch/arm/mach-exynos/platsmp.o
/tmp/ccdQM0Eg.s: Assembler messages:
/tmp/ccdQM0Eg.s:432: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:437: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:438: Error: selected processor does not support ARM mode `dsb '
make[1]: *** [arch/arm/mach-exynos/platsmp.o] Error 1
The error was introduced in commit "ARM: EXYNOS: Move code from
hotplug.c to platsmp.c". Previously code using
v7_exit_coherency_flush() macro was built with '-march=armv7-a' flag but
this flag dissapeared during the movement.
Fix this by annotating the v7_exit_coherency_flush() asm code with
armv7-a architecture.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct type (SSM2602/SSM2603/SSM2604) is passed down
from the ssm2602_spi_probe()/ssm2602_spi_probe() functions,
so use that instead of hardcoding it to SSM2602 in
ssm2602_probe().
Fixes: c924dc68f737 ("ASoC: ssm2602: Split SPI and I2C code into different modules")
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
|
|
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the Thinkpads' firmware will issue a backlight change request
through i915 operation region unconditionally on AC plug/unplug, the
backlight level used is arbitrary and thus should be ignored. This is
handled by commit 0b9f7d93ca61 (ACPI / i915: ignore firmware requests
for backlight change). Then there is a Dell laptop whose vendor backlight
interface also makes use of operation region to change backlight level
and with the above commit, that interface no long works. The condition
used to ignore the backlight change request from firmware is thus
changed to: if the vendor backlight interface is not in use and the ACPI
backlight interface is broken, we ignore the requests; oterwise, we keep
processing them.
Fixes: 0b9f7d93ca61 (ACPI / i915: ignore firmware requests for backlight change)
Link: https://lkml.org/lkml/2014/9/23/854
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Negated expressions and sub-expressions need to have their flags checked for
TCF_EM_INVERT and their result negated accordingly.
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we use WC updates of the PTE, we are responsible for notifying the
hardware when to flush its TLBs. Do so after we zap all the PTEs before
suspend (and the BIOS tries to read our GTT).
Fixes a regression from
commit 828c79087cec61eaf4c76bb32c222fbe35ac3930
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Wed Oct 16 09:21:30 2013 -0700
drm/i915: Disable GGTT PTEs on GEN6+ suspend
that survived and continue to cause harm even after
commit e568af1c626031925465a5caaab7cca1303d55c7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 26 20:08:20 2014 +0100
drm/i915: Undo gtt scratch pte unmapping again
v2: Trivial rebase.
v3: Fixes requires pointer dances.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82340
Tested-by: ming.yao@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When building this driver as a module, we get a helpful warning
about the return type:
drivers/cpufreq/integrator-cpufreq.c:232:2: warning: initialization from incompatible pointer type
.remove = __exit_p(integrator_cpufreq_remove),
If the remove callback returns void, the caller gets an undefined
value as it expects an integer to be returned. This fixes the
problem by passing down the value from cpufreq_unregister_driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix the following bug introduced by commit 8fec051eea73 (cpufreq:
Convert existing drivers to use cpufreq_freq_transition_{begin|end})
that forgot to move the spin_lock() in pcc_cpufreq_target() past
cpufreq_freq_transition_begin() which calls wait_event():
BUG: sleeping function called from invalid context at drivers/cpufreq/cpufreq.c:370
in_atomic(): 1, irqs_disabled(): 0, pid: 2636, name: modprobe
Preemption disabled at:[<ffffffffa04d74d7>] pcc_cpufreq_target+0x27/0x200 [pcc_cpufreq]
[ 51.025044]
CPU: 57 PID: 2636 Comm: modprobe Tainted: G E 3.17.0-default #7
Hardware name: Hewlett-Packard ProLiant DL980 G7, BIOS P66 07/07/2010
00000000ffffffff ffff88026c46b828 ffffffff81589dbd 0000000000000000
ffff880037978090 ffff88026c46b848 ffffffff8108e1df ffff880037978090
0000000000000000 ffff88026c46b878 ffffffff8108e298 ffff88026d73ec00
Call Trace:
[<ffffffff81589dbd>] dump_stack+0x4d/0x90
[<ffffffff8108e1df>] ___might_sleep+0x10f/0x180
[<ffffffff8108e298>] __might_sleep+0x48/0xd0
[<ffffffff8145b905>] cpufreq_freq_transition_begin+0x75/0x140 drivers/cpufreq/cpufreq.c:370 wait_event(policy->transition_wait, !policy->transition_ongoing);
[<ffffffff8108fc99>] ? preempt_count_add+0xb9/0xc0
[<ffffffffa04d7513>] pcc_cpufreq_target+0x63/0x200 [pcc_cpufreq] drivers/cpufreq/pcc-cpufreq.c:207 spin_lock(&pcc_lock);
[<ffffffff810e0d0f>] ? update_ts_time_stats+0x7f/0xb0
[<ffffffff8145be55>] __cpufreq_driver_target+0x85/0x170
[<ffffffff8145e4c8>] od_check_cpu+0xa8/0xb0
[<ffffffff8145ef10>] dbs_check_cpu+0x180/0x1d0
[<ffffffff8145f310>] cpufreq_governor_dbs+0x3b0/0x720
[<ffffffff8145ebe3>] od_cpufreq_governor_dbs+0x33/0xe0
[<ffffffff814593d9>] __cpufreq_governor+0xa9/0x210
[<ffffffff81459fb2>] cpufreq_set_policy+0x1e2/0x2e0
[<ffffffff8145a6cc>] cpufreq_init_policy+0x8c/0x110
[<ffffffff8145c9a0>] ? cpufreq_update_policy+0x1b0/0x1b0
[<ffffffff8108fb99>] ? preempt_count_sub+0xb9/0x100
[<ffffffff8145c6c6>] __cpufreq_add_dev+0x596/0x6b0
[<ffffffffa016c608>] ? pcc_cpufreq_probe+0x4b4/0x4b4 [pcc_cpufreq]
[<ffffffff8145c7ee>] cpufreq_add_dev+0xe/0x10
[<ffffffff81408e81>] subsys_interface_register+0xc1/0xf0
[<ffffffff8108fb99>] ? preempt_count_sub+0xb9/0x100
[<ffffffff8145b3d7>] cpufreq_register_driver+0x117/0x2a0
[<ffffffffa016c65d>] pcc_cpufreq_init+0x55/0x9f8 [pcc_cpufreq]
[<ffffffffa016c608>] ? pcc_cpufreq_probe+0x4b4/0x4b4 [pcc_cpufreq]
[<ffffffff81000298>] do_one_initcall+0xc8/0x1f0
[<ffffffff811a731d>] ? __vunmap+0x9d/0x100
[<ffffffff810eb9a0>] do_init_module+0x30/0x1b0
[<ffffffff810edfa6>] load_module+0x686/0x710
[<ffffffff810ebb20>] ? do_init_module+0x1b0/0x1b0
[<ffffffff810ee1db>] SyS_init_module+0x9b/0xc0
[<ffffffff8158f7a9>] system_call_fastpath+0x16/0x1b
Fixes: 8fec051eea73 (cpufreq: Convert existing drivers to use cpufreq_freq_transition_{begin|end})
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The reset_resume call is needed, otherwise it will break resume
on some conditions, depending on the usb ehci/xhci controller.
This reverts commit b89193e0b06f44f48e3bf897a5b5cb4a7aff3359.
Reported-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
|
|
Fixes: commit f187bc6efb7250afee0e2009b6106 ("ipv4: No need to set generic neighbour pointer")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6gre_tunnel_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
