| Commit message (Collapse) | Author | Age | Files | Lines |
|\
| |
| |
| |
| |
| | |
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
A typo in qca808x_read_status means we try to set SMII mode on the port
rather than SGMII when the link speed is not 2.5Gb/s. This results in no
traffic due to the mismatch in configuration between the phy and the
mac.
v2:
Only change interface mode when the link is up
Fixes: 79c7bc0521545 ("net: phy: add qca8081 read_status")
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for downstream SFP cages for AR8031 and AR8033. This is
primarily intended for fiber modules or direct-attach cables, however
copper modules which work in 1000Base-X mode may also function. Such
modules are allowed with a warning.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.
Enable the appropriate interrupt bits to detect fiber-side link up
or down events.
Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
| |
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
Don't populate the read-only const array offsets on the stack
but instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220109231716.59012-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix the following coccicheck warning:
./drivers/net/phy/at803x.c:493:5-10: WARNING: Unsigned expression
compared with zero: value < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7beecaf7d507 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/1635325191-101815-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
To perform CDT of qca8081 phy:
1. disable hibernation.
2. force phy working in MDI mode.
3. force phy working in 1000BASE-T mode.
4. configure the related thresholds.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1. The master/slave seed needs to be updated when the link can't
be created.
2. The case where two qca8081 PHYs are connected each other and
master/slave seed is generated as the same value also needs
to be considered, so adding this code change into read_status
instead of link_change_notify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
qca8081 phy is a single port phy, configure
phy the lower seed value to make it linked as slave
mode easier.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Add the qca8081 phy driver config_init function, which includes:
1. Enable fast restrain.
2. Add 802.3az configurations.
3. Initialize ADC threshold as 100mv.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Reuse at803x phy driver config_aneg excepting
adding 2500M auto-negotiation.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Reuse the at803x phy driver get_features excepting
adding 2500M capability.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1. Separate the function at803x_read_specific_status from
the at803x_read_status, since it can be reused by the
read_status of qca8081 phy driver excepting adding the
2500M speed.
2. Add the qca8081 read_status function qca808x_read_status.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
qca8081 is a single port ethernet phy chip that supports
10/100/1000/2500 Mbps mode.
Add the basic phy driver features, and reuse the at803x
phy driver functions.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Use GENMASK() for the current speed value.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The wol feature is controlled by the MMD3.8012 bit5,
need to set this bit when the wol function is enabled.
The reg18 bit0 is for enabling WOL interrupt, when wol
occurs, the wol interrupt status reg19 bit0 is set to 1.
Call phy_trigger_machine if there are any other interrupt
pending in the function set_wol.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Convert at803x_set_wol to use phy_modify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Give a name to known debug regs from Documentation instead of using
unknown hex values.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.
Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.
Fixes: 15b9df4ece17 ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for the embedded fast-ethernet PHY found on the QCA9561
WiSoC platform. It supports the usual Atheros PHY featureset including
the cable tester.
Tested on a Xiaomi MiRouter 4Q (QCA9561)
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20211005225401.10653-1-mail@david-bauer.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
| |
Fix spacing and improve name for 83xx phy following other phy in the
same driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
Add resume/suspend function to qca83xx internal phy.
We can't use the at803x generic function as the documentation lacks of
any support for WoL regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
For qca8327 internal phy there are 2 different switch variant with 2
different phy id. Add this missing variant so the internal phy can be
correctly identified and fixed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
The blamed commit was probably not tested on net-next, since it did not
refactor the extra phy id check introduced in commit b856150c8098 ("net:
phy: at803x: mask 1000 Base-X link mode").
Fixes: 8887ca5474bd ("net: phy: at803x: simplify custom phy id matching")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since the at803x share the same regs, it's assumed they are based on the
same implementation. Make it part of the at803x PHY driver to skip
having redudant code.
Add initial support for qca8k internal PHYs. The internal PHYs requires
special mmd and debug values to be set based on the switch revision
passwd using the dev_flags. Supports output of idle, receive and eee_wake
errors stats.
Some debug values sets can't be translated as the documentation lacks any
reference about them.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
| |
Clean any whitespace errors and fix not aligned define.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The commit c329e5afb42f ("net: phy: at803x: select correct page on
config init") selects the copper page during probe. This fails if the
copper page was already selected. In this case, the value of the copper
page (which is 1) is propagated through phy_restore_page() and is
finally returned for at803x_probe(). Fix it, by just using the
at803x_page_write() directly.
Also in case of an error, the regulator is not disabled and leads to a
WARN_ON() when the probe fails. This couldn't happen before, because
at803x_parse_dt() was the last call in at803x_probe(). It is hard to
see, that the parse_dt() actually enables the regulator. Thus move the
regulator_enable() to the probe function and undo it in case of an
error.
Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.
The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.
Select the copper page when probing to circumvent this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Here is what Vladimir says about it:
at803x_aneg_done() keeps the aneg reporting as "not done" even when
the copper-side link was reported as up, but the in-band autoneg has
not finished.
That was the _intended_ behavior when that code was introduced, and
Heiner have said about it [1]:
| That's not nice from the PHY:
| It signals "link up", and if the system asks the PHY for link details,
| then it sheepishly says "well, link is *almost* up".
If the specification of phy_aneg_done behavior does not include
in-band autoneg (and it doesn't), then this piece of code does not
belong here.
The fact that we can no longer trigger this code from phylib is yet
another reason why it fails at its intended (and wrong) purpose and
should be removed.
Removing the SGMII link check, would just keep the call to
genphy_aneg_done(), which is also the fallback. Thus we can just remove
at803x_aneg_done() altogether.
[1] https://lore.kernel.org/netdev/fdf0074a-2572-5914-6f3e-77202cbf96de@gmail.com/
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
AR8035 recently gained MDIX support. The same functions will work for
the AR8031/33 PHY. We just need to add the at803x_config_aneg()
callback.
This was tested on a Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SmartEEE for the atheros phy was deemed buggy by Freescale and commits
were added to disable it for their boards.
In initial testing, SolidRun found that the default settings were
causing disconnects but by increasing the Tw buffer time we could allow
enough time for all parts of the link to come out of a low power state
and function properly without causing a disconnect. This allows us to
have functional power savings of between 300 and 400mW, rather than
disabling the feature altogether.
This commit adds support for disabling SmartEEE and configuring the Tw
parameters for 1G and 100M speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This bit is enabled by default and advertises support for extended
next page support. XNP is only needed for 10GBase-T and MultiGig
support which is not supported. Additionally, Cisco MultiGig switches
will read this bit and attempt 10Gb negotiation even though Next Page
support is disabled. This will cause timeouts when the interface is
forced to 100Mbps and auto-negotiation will fail. The interfaces are
only 1000Base-T and supporting auto-negotiation for this only requires
the Next Page bit to be set.
Taken from:
https://github.com/SolidRun/linux-stable/commit/7406c5244b7ea6bc17a2afe8568277a8c4b126a9
and adapted to mainline kernels by rmk.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kzSdb-000417-FJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
| |
Convert at803x_clk_out_config() to use phy_modify_mmd().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyc72-0008Pq-1x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
|
|
|
|
|
|
| |
The only usage of vddio_regulator_ops and vddh_regulator_ops is to
assign their address to the ops field in the regulator_desc struct,
which is a const pointer. Make them const to allow the compiler to
put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch add MDIX configuration ability for AR9331 and AR8035. Theoretically
it should work on other Atheros PHYs, but I was able to test only this
two.
Since I have no certified reference HW able to detect or configure MDIX, this
functionality was confirmed by oscilloscope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
By placing the GENMASK value into an unsigned int and then passing it
to PREF_FIELD, the type is reduces down from ULL. Given the reduced
size of the type, the range checks in PREP_FAIL() are always true, and
-Wtype-limits then gives a warning.
By skipping the intermediate variable, the warning can be avoided.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Ever since its first commit 0ca7111a38f05 ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
- for AR8031/AR8033 its 0x004d/0xd074
- for AR8035 its 0x004d/0xd072
Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.
I've tried to contact the author of the initial commit, but received no
answer so far.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The AR8031/AR8033 and the AR8035 support cable diagnostics. Adding
driver support is straightforward, so lets add it.
The PHY just do one pair at a time, so we have to start the test four
times. The cable_test_get_status() can block and therefore we can just
busy poll the test completion and continue with the next pair until we
are done.
The time delta counter seems to run at 125MHz which just gives us a
resolution of about 82.4cm per tick.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair A, fault length: 107.94m
Pair: Pair B, result: Open Circuit
Pair: Pair B, fault length: 104.64m
Pair: Pair C, result: Open Circuit
Pair: Pair C, fault length: 105.47m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 107.94m
1m cable, A/B connected, C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair C, fault length: 0.82m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 0.82m
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The AR8031 and AR8035 support the link speed downshift. Add driver
support for it. One peculiarity of these PHYs is that it needs a
software reset after changing the setting, thus add the .soft_reset()
op and do a phy_init_hw() if necessary.
This was tested on a custom board with the AR8031.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|