summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/sfp.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: sfp: fix high power modules without diagnostic monitoringRussell King (Oracle)2022-01-171-4/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") unintetionally changed the semantics for high power modules without the digital diagnostics monitoring. We repeatedly attempt to read the power status from the non-existing 0xa2 address in a futile hope this failure is temporary: [ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408 [ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode [ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5 [ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5 [ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5 We previosuly assumed such modules were powered up in the correct mode, continuing without further configuration as long as the required power class was supported by the host. Restore this behaviour, while preserving the intent of subsequent patches to avoid the "Address Change Sequence not supported" warning if we are not going to be accessing the DDM address. Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") Reported-by: 照山周一郎 <teruyama@springboard-inc.jp> Tested-by: 照山周一郎 <teruyama@springboard-inc.jp> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: Fix typo in state machine debug stringSean Anderson2021-10-051-1/+1
| | | | | | | | | The string should be "tx_disable" to match the state enum. Fixes: 4005a7cb4f55 ("net: phy: sftp: print debug message with text, not numbers") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: delete repeated words of commentsWenpeng Liang2021-06-161-1/+1
| | | | | | | | | There are some repeated words in some comments, they should be deleted. Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Weihang Li <liweihang@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: sfp: add netlink SFP support to generic SFP codeAndrew Lunn2021-04-121-0/+25
| | | | | | | | | | | | | | | | | The new netlink API for reading SFP data requires a new op to be implemented. The idea of the new netlink SFP code is that userspace is responsible to parsing the EEPROM data and requesting pages, rather than have the kernel decide what pages are interesting and returning them. This allows greater flexibility for newer formats. Currently the generic SFP code only supports simple SFPs. Allow i2c address 0x50 and 0x51 to be accessed with page and bank must always be 0. This interface will later be extended when for example QSFP support is added. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber InstantPali Rohár2021-01-281-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information stored in its EEPROM. It claims to support all transceiver types including 10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is the only one supported. This module has also phys_id set to SFF, and the SFP subsystem currently does not allow to use SFP modules detected as SFFs. Add exception for this module so it can be detected as supported. This change finally allows to detect and use SFP GPON module Ubiquiti U-Fiber Instant on Linux system. EEPROM content of this SFP module is (where XX is serial number): 00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.?? 10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT 20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA 30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6 40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX 50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: sfp: add workaround for Realtek RTL8672 and RTL9601C chipsPali Rohár2021-01-281-33/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The workaround for VSOL V2801F brand based GPON SFP modules added in commit 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround") works only for IDs added explicitly to the list. Since there are rebranded modules where OEM vendors put different strings into the vendor name field, we cannot base workaround on IDs only. Moreover the issue which the above mentioned commit tried to work around is generic not only to VSOL based modules, but rather to all GPON modules based on Realtek RTL8672 and RTL9601C chips. These include at least the following GPON modules: * V-SOL V2801F * C-Data FD511GX-RM0 * OPTON GP801R * BAUDCOM BD-1234-SFM * CPGOS03-0490 v2.0 * Ubiquiti U-Fiber Instant * EXOT EGS1 These Realtek chips have broken EEPROM emulator which for N-byte read operation returns just the first byte of EEPROM data, followed by N-1 zeros. Introduce a new function, sfp_id_needs_byte_io(), which detects SFP modules with broken EEPROM emulator based on N-1 zeros and switch to 1 byte EEPROM reading operation. Function sfp_i2c_read() now always uses single byte reading when it is required and when function sfp_hwmon_probe() detects single byte access, it disables registration of hwmon device, because in this case we cannot reliably and atomically read 2 bytes as is required by the standard for retrieving values from diagnostic area. (These Realtek chips are broken in a way that violates SFP standards for diagnostic interface. Kernel in this case simply cannot do anything less of skipping registration of the hwmon interface.) This patch fixes reading of EEPROM content from SFP modules based on Realtek RTL8672 and RTL9601C chips. Diagnostic interface of EEPROM stays broken and cannot be fixed. Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround") Co-developed-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: sfp: add debugfs supportRussell King2021-01-131-0/+55
| | | | | | | | | | | | | | | | | | | | | | | Add debugfs support to SFP so that the internal state of the SFP state machines and hardware signal state can be viewed from userspace, rather than having to compile a debug kernel to view state transitions in the kernel log. The 'state' output looks like: Module state: empty Module probe attempts: 0 0 Device state: up Main state: down Fault recovery remaining retries: 5 PHY probe remaining retries: 12 moddef0: 0 rx_los: 1 tx_fault: 1 tx_disable: 1 Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1kyYRe-0004kN-3F@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: sfp: cope with SFPs that set both LOS normal and LOS invertedRussell King2021-01-121-14/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The SFP MSA defines two option bits in byte 65 to indicate how the Rx_LOS signal on SFP pin 8 behaves: bit 2 - Loss of Signal implemented, signal inverted from standard definition in SFP MSA (often called "Signal Detect"). bit 1 - Loss of Signal implemented, signal as defined in SFP MSA (often called "Rx_LOS"). Clearly, setting both bits results in a meaningless situation: it would mean that LOS is implemented in both the normal sense (1 = signal loss) and inverted sense (0 = signal loss). Unfortunately, there are modules out there which set both bits, which will be initially interpret as "inverted" sense, and then, if the LOS signal changes state, we will toggle between LINK_UP and WAIT_LOS states. Change our LOS handling to give well defined behaviour: only interpret these bits as meaningful if exactly one is set, otherwise treat it as if LOS is not implemented. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaroundRussell King2020-12-101-5/+58
| | | | | | | | | | | | | | | | | | Add a workaround for the detection of VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single byte I2C reads to the EEPROM. Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module, which reports a manufacturer of "OEM". This manufacturer can't be matched as it appears in many different modules, so also match the part number too. Reported-by: Thomas Schreiber <tschreibe@gmail.com> Reported-by: Pali Rohár <pali@kernel.org> Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfp: Fix error handing in sfp_probe()YueHaibing2020-11-031-1/+2
| | | | | | | | | | | gpiod_to_irq() never return 0, but returns negative in case of error, check it and set gpio_irq to 0. Fixes: 73970055450e ("sfp: add SFP module support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20201031031053.25264-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2020-09-051-6/+6
|\ | | | | | | | | | | | | | | | | | | | | | | We got slightly different patches removing a double word in a comment in net/ipv4/raw.c - picked the version from net. Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached values instead of VNIC login response buffer (following what commit 507ebe6444a4 ("ibmvnic: Fix use-after-free of VNIC login response buffer") did). Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva2020-08-241-6/+6
| | | | | | | | | | | | | | | | | | | | Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
* | net/phy/mdio-i2c: Move header file to include/linux/mdioAndrew Lunn2020-08-271-1/+1
|/ | | | | | | | | | | | | | In preparation for moving all MDIO drivers into drivers/net/mdio, move the mdio-i2c header file into include/linux/mdio so it can be used by both the MDIO driver and the SFP code which instantiates I2C MDIO busses. v2: Add include/linux/mdio Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: sfp: Cotsworks SFF module EEPROM fixupChris Healy2020-07-171-0/+44
| | | | | | | | | | | | | Some Cotsworks SFF have invalid data in the first few bytes of the module EEPROM. This results in these modules not being detected as valid modules. Address this by poking the correct EEPROM values into the module EEPROM when the model/PN match and the existing module EEPROM contents are not correct. Signed-off-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: add error checking with sfp_irq_nameChris Healy2020-07-081-0/+3
| | | | | | | Add error checking with sfp_irq_name before use. Signed-off-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: Unique GPIO interrupt namesChris Healy2020-07-071-1/+6
| | | | | | | | | | | | | | | | | | | | Dynamically generate a unique GPIO interrupt name, based on the device name and the GPIO name. For example: 103: 0 sx1503q 12 Edge sff2-los 104: 0 sx1503q 13 Edge sff2-tx-fault The sffX indicates the SFP the los and tx-fault are associated with. v3: - reverse Christmas tree new variable - fix spaces vs tabs v2: - added net-next to PATCH part of subject line - switched to devm_kasprintf() Signed-off-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: report error on failure to read sfp soft statusRussell King2019-12-201-2/+9
| | | | | | | | | Report a rate-limited error if we fail to read the SFP soft status, and preserve the current status in that case. This avoids I2C bus errors from triggering a link flap. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: re-attempt probing for phyRussell King2019-12-111-17/+42
| | | | | | | | | | | | | | | Some 1000BASE-T PHY modules take a while for the PHY to wake up. Retry the probe a number of times before deciding that the module has no PHY. Tested with: Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond. Champion One 1000SFPT - PHY takes about 200ms to respond. Mikrotik S-RJ01 - no PHY Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: error handling for phy probeRussell King2019-12-111-9/+17
| | | | | | Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: rename sm_retriesRussell King2019-12-111-5/+5
| | | | | | | | | Rename sm_retries as sm_fault_retries, as this is what this member is tracking. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: use a definition for the fault recovery attemptsRussell King2019-12-111-3/+11
| | | | | | Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: add support for Clause 45 PHYsRussell King2019-12-111-4/+40
| | | | | | | | | | Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via the normal I2C address. Detect 10G BASE-T PHYs which may have an accessible PHY and probe for it. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: move phy_start()/phy_stop() to phylinkRussell King2019-12-111-2/+0
| | | | | | | | | | | Move phy_start() and phy_stop() into the module_start and module_stop notifications in phylink, rather than having them in the SFP code. This gives phylink responsibility for controlling the PHY, rather than having SFP start and stop the PHY state machine. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: add module start/stop upstream notificationsRussell King2019-12-111-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | When dealing with some copper modules, we can't positively know the module capabilities are until we have probed the PHY. Without the full capabilities, we may end up failing a module that we could otherwise drive with a restricted set of capabilities. An example of this would be a module with a NBASE-T PHY plugged into a host that supports phy interface modes 2500BASE-X and SGMII. The PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes, which means a subset of the capabilities are compatible with the host. However, reading the module EEPROM leads us to believe that the module only supports ethtool link mode 10GBASE-T, which is incompatible with the host - and thus results in the module being rejected. This patch adds an extra notification which are triggered after the SFP module's PHY probe, and a corresponding notification just before the PHY is removed. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: add more extended compliance codesRussell King2019-12-111-2/+2
| | | | | | | | | | | | | SFF-8024 is used to define various constants re-used in several SFF SFP-related specifications. Split these constants from the enum, and rename them to indicate that they're defined by SFF-8024. Add and use updated SFF-8024 extended compliance code definitions for 10GBASE-T, 5GBASE-T and 2.5GBASE-T modules. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: remove incomplete 100BASE-FX and 100BASE-LX supportRussell King2019-12-111-12/+1
| | | | | | | | | | | The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this is probably an incorrect assumption. In any case, sfp_parse_support() will fail such a module. Let's stop pretending we support these modules. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: avoid tx-fault with Nokia GPON moduleRussell King2019-12-091-12/+30
| | | | | | | | | | The Nokia GPON module can hold tx-fault active while it is initialising which can take up to 60s. Avoid this causing the module to be declared faulty after the SFP MSA defined non-cooled module timeout. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: fix hwmonRussell King2019-12-051-9/+4
| | | | | | | | | | The referenced commit below allowed more than one hwmon device to be created per SFP, which is definitely not what we want. Avoid this by only creating the hwmon device just as we transition to WAITDEV state. Fixes: 139d3a212a1f ("net: sfp: allow modules with slow diagnostics to probe") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: fix unbindRussell King2019-12-051-0/+4
| | | | | | | | | | When unbinding, we don't correctly tear down the module state, leaving (for example) the hwmon registration behind. Ensure everything is properly removed by sending a remove event at unbind. Fixes: 6b0da5c9c1a3 ("net: sfp: track upstream's attachment state in state machine") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: soft status and control supportRussell King2019-11-211-20/+90
| | | | | | | | | | | | Add support for the soft status and control register, which allows TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We make use of this when the board does not support GPIOs for these signals. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: fix spelling mistake "requies" -> "requires"Colin Ian King2019-11-131-1/+1
| | | | | | | There is a spelling mistake in a dev_warn message. Fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: allow modules with slow diagnostics to probeRussell King2019-11-121-22/+74
| | | | | | | | | | | | | | | | | | | | | When a module is inserted, we attempt to read read the ID from address 0x50. Once we are able to read the ID, we immediately attempt to initialise the hwmon support by reading from address 0x51. If this fails, then we fall into error state, and assume that the module is not usable. Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for I2C address 0x50, which responds immediately. However, address 0x51 is an emulated, which only becomes available once the on-board firmware has booted. This prompts us to fall into the error state. Since the module may be usable without diagnostics, arrange for the hwmon probe independent of the rest of the SFP itself, retrying every 5s for up to about 60s for the monitoring to become available, and print an error message if it doesn't become available. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: allow sfp to probe slow to initialise GPON modulesRussell King2019-11-121-10/+28
| | | | | | | | | | | | | Some GPON modules (e.g. Huawei MA5671A) take a significant amount of time to start responding on the I2C bus, contary to the SFF specifications. Work around this by implementing a two-level timeout strategy, where we initially quickly retry for the module, and then use a slower retry after we exceed a maximum number of quick attempts. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: move module insert reporting out of probeRussell King2019-11-121-18/+40
| | | | | | | | | | | | | | | Move the module insertion reporting out of the probe handling, but after we have detected that the upstream has attached (since that is whom we are reporting insertion to.) Only report module removal if we had previously reported a module insertion. This gives cleaner semantics, and means we can probe the module before we have an upstream attached. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: split power mode switching from probeRussell King2019-11-121-37/+64
| | | | | | | | | | | | | Switch the power mode switching from the probe, so that we don't repeatedly re-probe the SFP device if there is a problem accessing the registers at I2C address 0x51. In splitting this out, we can also fix a bug where we leave the module in high-power mode when the upstream device is detached but the module is still inserted. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: track upstream's attachment state in state machineRussell King2019-11-121-13/+29
| | | | | | | | | | | | | | | | | | Track the upstream's attachment state in the state machine rather than maintaining a boolean, which ensures that we have a strict order of ATTACH followed by an UP event - we can never believe that a newly attached upstream will be anything but down. Rearrange the order of state machines so we run the module state machine after the upstream device's state machine, so the module state machine can check the current state of the device and take action to e.g. reset back to empty state when the upstream is detached. This is to allow the module detection to run independently of the network device becoming available. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: ensure TX_FAULT has deasserted before probing the PHYRussell King2019-11-121-6/+25
| | | | | | | | | | | | | TX_FAULT should be deasserted to indicate that the module has completed its initialisation. This may include the on-board PHY, so wait until the module has deasserted TX_FAULT before probing the PHY. This means that we need an extra state to handle a TX_FAULT that remains set for longer than t_init, since using the existing handling state would bypass the PHY probe. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: allow fault processing to transition to other statesRussell King2019-11-121-6/+6
| | | | | | | | Add the next state to sfp_sm_fault() so that it can branch to other states. This will be necessary to improve the initialisation path. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: eliminate mdelay() from PHY probeRussell King2019-11-121-12/+40
| | | | | | | | | | | Rather than using mdelay() to wait before probing the PHY (which holds several locks, including the rtnl lock), add an extra wait state to the state machine to introduce the 50ms delay without holding any locks. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: split the PHY probe from sfp_sm_mod_init()Russell King2019-11-121-8/+13
| | | | | | | | | | Move the PHY probe into a separate function, splitting it from sfp_sm_mod_init(). This will allow us to eliminate the 50ms mdelay() inside the state machine. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: control TX_DISABLE and phy only from main state machineRussell King2019-11-121-8/+1
| | | | | | | | | | | | | | | | | | | | | We initialise TX_DISABLE when the sfp cage is probed, and then maintain its state in the main state machine. However, the module state machine: - negates it when detecting a newly inserted module when it's already guaranteed to be negated. - negates it when the module is removed, but the main state machine will do this anyway. Make TX_DISABLE entirely controlled by the main state machine. The main state machine also probes the module for a PHY, and removes the PHY when the the module is removed. Hence, removing the PHY in sfp_sm_module_remove() is also redundant, and is a left-over from when we tried to probe for the PHY from the module state machine. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: avoid power switch on address-change modulesRussell King2019-11-121-11/+20
| | | | | | | | | | | | If the module indicates that it requires an address change sequence to switch between address 0x50 and 0x51, which we don't support, we can't write to the register that controls the power mode to switch to high power mode. Warn the user that the module may not be functional in this case, and don't try to change the power mode. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: parse SFP power requirement earlierRussell King2019-11-121-13/+29
| | | | | | | | | Parse the SFP power requirement earlier, in preparation for moving the power level setup code. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: rename T_PROBE_WAIT to T_SERIALRussell King2019-11-121-7/+6
| | | | | | | | | | SFF-8472 rev 12.2 defines the time for the serial bus to become ready using t_serial. Use this as our identifier for this timeout to make it clear what we are referring to. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: handle module remove outside state machineRussell King2019-11-121-7/+9
| | | | | | | | | | Removing a module resets the module state machine back to its initial state. Rather than explicitly handling this in every state, handle it early on outside of the state machine. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: rename sfp_sm_ins_next() as sfp_sm_mod_next()Russell King2019-11-121-8/+8
| | | | | | | | | sfp_sm_ins_next() modifies the module state machine. Change it's name to reflect this. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: move tx disable on device down to main state machineRussell King2019-11-121-8/+2
| | | | | | | | | Move the tx disable assertion on device down to the main state machine. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfp: move sfp sub-state machines into separate functionsRussell King2019-11-121-31/+43
| | | | | | | | | | | Move the SFP sub-state machines out of the main state machine function, in preparation for it doing a bit more with the device state. By doing so, we ensure that our debug after the main state machine is always printed. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: sfp: Add labels to hwmon sensorsAndrew Lunn2019-08-251-5/+68
| | | | | | | | | | | | | | | | | | | | SFPs can report two different power values, the transmit power and the receive power. Add labels to make it clear which is which. Also add labels to the other sensors, VCC power supply, bias and module temperature. sensors(1) now shows: sff2-isa-0000 Adapter: ISA adapter VCC: +3.23 V temperature: +33.4 C TX_power: 276.00 uW RX_power: 20.00 uW bias: +0.01 A Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: sfp: hwmon: Fix scaling of RX powerAndrew Lunn2019-07-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The RX power read from the SFP uses units of 0.1uW. This must be scaled to units of uW for HWMON. This requires a divide by 10, not the current 100. With this change in place, sensors(1) and ethtool -m agree: sff2-isa-0000 Adapter: ISA adapter in0: +3.23 V temp1: +33.1 C power1: 270.00 uW power2: 200.00 uW curr1: +0.01 A Laser output power : 0.2743 mW / -5.62 dBm Receiver signal average optical power : 0.2014 mW / -6.96 dBm Reported-by: chris.healy@zii.aero Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors") Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-09 15:16:41 +0100