summaryrefslogtreecommitdiffstats
path: root/drivers/net/sfc (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: Fix warning fallout from recent NAPI interface changes.David S. Miller2008-12-271-1/+0
| | | | | | | | | | | When we removed the network device argument from several NAPI interfaces in 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused netdev arg from some NAPI interfaces.") several drivers now started getting unused variable warnings. This fixes those up. Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings2008-12-261-7/+10
| | | | | | | | | When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings2008-12-261-24/+23
| | | | | | | | This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: SFT9001: Add cable diagnosticsBen Hutchings2008-12-261-8/+107
| | | | | | | | | | The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for multiple PHY self-testsBen Hutchings2008-12-265-15/+44
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Merge top-level functions for self-testsBen Hutchings2008-12-263-55/+48
| | | | | | | Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up PHY mode management in loopback self-testBen Hutchings2008-12-261-12/+7
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix unreliable link detection in some loopback modesBen Hutchings2008-12-263-13/+24
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Generate unique names for per-NIC workqueuesBen Hutchings2008-12-262-1/+6
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Remove unused netdev arg from some NAPI interfaces.Neil Horman2008-12-232-2/+2
| | | | | | | | | | When the napi api was changed to separate its 1:1 binding to the net_device struct, the netif_rx_[prep|schedule|complete] api failed to remove the now vestigual net_device structure parameter. This patch cleans up that api by properly removing it.. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Version 2.3Ben Hutchings2008-12-131-1/+1
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix synchronisation of efx_mtd_{probe,rename,remove}Ben Hutchings2008-12-131-15/+18
| | | | | | | | | | | | | Currently efx_mtd_rename() can race with the probe() and remove() functions. Move probe() before device registration and remove() after unregistration. Move initialisation/update of all names based on the netdev name into a new function and call it under the RTNL immediately after registration. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use kzalloc() to ensure struct efx_spi_device is fully initialisedBen Hutchings2008-12-131-1/+1
| | | | | | | Currently the mtd field is not initialised early enough. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Treat probe as unsuccessful if it scheduled a resetSteve Hodgson2008-12-131-2/+11
| | | | | | | | | | From: Steve Hodgson <shodgson@solarflare.com> efx_pci_probe_main() can return success despite a reset being scheduled. Catch this and retry or abort probe depending on the reset type. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use model numbers for PHY type namesBen Hutchings2008-12-133-5/+5
| | | | | | | | | | Some of the PHY type names are overly generic. Change them to include the model numbers of the PHYs they represent. Correct the model number reference at the top of xfp_phy.c. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use mutex_lock_interruptible() for ethtool EEPROM accessBen Hutchings2008-12-131-2/+8
| | | | | | | | | ethtool must contend with the MTD driver for the SPI bus lock, which may carry out long operations such as flash erase. Allow it to be interrupted while waiting. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Specify a meaningful component for loopback RX-side and PHY testsBen Hutchings2008-12-131-6/+8
| | | | | | | | | Our ethtool self-test result names each begin with a component name. For some results this is "port0", which is not very meaningful. Change that to "rx" or "phy" as appropriate. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Remove leading spacesBen Hutchings2008-12-131-2/+2
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for SFN4111TBen Hutchings2008-12-137-35/+150
| | | | | | | | Add support code for the SFN4111T 100/1000/10GBASE-T reference design, based in part on the existing code for the SFE4001. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for Solarflare 10Xpress SFT9001Ben Hutchings2008-12-138-105/+467
| | | | | | | | | | | | Add type codes for the new PHY and rename the SFX7101 type code. Add definition of clause 22 extension MMD. Adapt the 10Xpress SFX7101 code to support the SFT9001 as well. Clean up register definitions. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Rework MAC, PHY and board event handlingBen Hutchings2008-12-139-114/+111
| | | | | | | | | | | From: Steve Hodgson <shodgson@solarflare.com> MAC, PHY and board events may be separately enabled and signalled. Our current arrangement of chaining the polling functions can result in events being missed. Change them to be more independent. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Implement auto-negotiationBen Hutchings2008-12-139-154/+472
| | | | | | | | | | | | Add infrastructure for auto-negotiation of speed, duplex and flow control. When using 10Xpress, auto-negotiate flow control. While we're at it, clean up the code to warn when partner is not 10GBASE-T capable. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for sub-10G speedsBen Hutchings2008-12-1316-321/+699
| | | | | | | | | | | | | The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce an efx_mac_operations structure with implementations for the two MACs. Switch between the MACs as necessary. PHY settings are independent of the MAC, so add get_settings() and set_settings() to efx_phy_operations. Also add macs field to indicate which MACs the PHY is connected to. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up MDIO flag settingBen Hutchings2008-12-132-59/+32
| | | | | | | | | We often want to set or clear a flag in an MDIO register, but avoid writing if no change is required since this can have side-effects. Encapsulate this in a function, mdio_clause45_set_flag(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up board identificationBen Hutchings2008-12-132-55/+20
| | | | | | | | | Remove kluge for development boards with unspecified board type. Remove assumption of contiguous board type code assignments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add phy_type device attributeBen Hutchings2008-12-131-0/+19
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for MMDs numbered >15Ben Hutchings2008-12-134-22/+24
| | | | | | | | Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of reading just DEVS0. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Remove MII extension cruftBen Hutchings2008-12-138-174/+18
| | | | | | | | | | Replace efx_nic::link_options bitfield with link_speed (speed in Mbit/s) and link_fd (full duplex flag). Remove broken auto-negotiation functions. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Don't count RX checksum errors during loopback self-testBen Hutchings2008-12-131-5/+8
| | | | | | | | | The loopback self-test checks that IP packets with incorrect checksums are not altered when sent on a queue with checksum generation off. These should not contribute to RX error statistics. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Abbreviate self-test names so they are not truncatedBen Hutchings2008-12-131-8/+8
| | | | | | | | | Change "channel" to "chan". Shorten PHY loopback names. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Provide hints to irqbalance daemonBen Hutchings2008-12-133-1/+27
| | | | | | | | Allocate IRQs with the name format <device>[-<type>]-<number> so that future versions of irqbalanced understand what we're doing. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add option to use a separate channel for TX completionsNeil Turton2008-12-132-15/+28
| | | | | | | | | | | | In a bidirectional forwarding test, we find that the best performance is achieved by sending the TX completion interrupts from one NIC to a CPU which shares an L2 cache with RX completion interrupts from the other NIC. To facilitate this, add an option (through a module parameter) to create separate channels for RX and TX completion with separate IRQs when MSI-X is available. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Restore phy_flash_cfg module parameterBen Hutchings2008-12-131-0/+7
| | | | | | | This is needed for recovery in case a PHY firmware upgrade is aborted. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Work around unreliable strap pinsBen Hutchings2008-12-131-70/+44
| | | | | | | | | | | The SFC4000 has strap pins indicating the presence of SPI flash and/or EEPROM. These pins are also used for GPIO, and in some cases they may be read wrongly at reset. However, on production boards it must boot from one or the other device, so we can assume the boot device is present and read the board config from there. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up waits for flash/EEPROM operationsBen Hutchings2008-12-133-23/+39
| | | | | | | | | | | | | | | | | | | | Make falcon_spi_wait() ignore the write timer - it is only relevant to write commands, it only works for the device that contains VPD, and it might not be initialised properly at all. Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting its use, and make it wait up to 10 ms (not 1 ms) since buffered writes to EEPROM may take this long to complete. Make both wait functions sleep instead of busy-waiting. Replace wait for command completion at top of falcon_spi_cmd() with a single poll; no command should be running when the function starts. Correct some comments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Make reset_workqueue driver-global rather than per-NICSteve Hodgson2008-12-132-27/+20
| | | | | | | | Each reset is serialised by the rtnl_lock anyway, so there's no win per-NIC. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Correct interpretation of second param to ethtool phys_id()Ben Hutchings2008-12-131-2/+6
| | | | | | | A value of 0 means indefinite repetition (until interrupted). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Remove unneeded register writeBen Hutchings2008-12-131-9/+0
| | | | | | | This was only ever needed for an FPGA version of Falcon. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Change SPI lengths to type size_tBen Hutchings2008-12-132-10/+11
| | | | | | | Based on a patch by Andrew Morton. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Board support fixesBen Hutchings2008-12-131-0/+2
| | | | | | | | | | Set dummy monitor method for unrecognised boards. Clean up board resources if efx_pci_probe_main() fails after board has been initialised. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: convert to net_device_opsStephen Hemminger2008-11-221-13/+18
| | | | | | | | Convert driver to new net_device_ops. Compile tested only. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix dependency for SFC_MTDBen Hutchings2008-11-201-1/+1
| | | | | | | | | Randy Dunlap found that SFC_MTD was selected when sfc was built-in and the MTD core was a module. Don't allow that combination. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdev: introduce dev_get_stats()Stephen Hemminger2008-11-201-1/+1
| | | | | | | | | | | | In order for the network device ops get_stats call to be immutable, the handling of the default internal network device stats block has to be changed. Add a new helper function which replaces the old use of internal_get_stats. Note: change return code to make it clear that the caller should not go changing the returned statistics. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Do not reset when hardware monitor detects a faultBen Hutchings2008-11-062-23/+6
| | | | | | | | The TX watchdog should trigger a reset, but a temperature/power alarm should not as this is unlikely to solve the problem. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Use lm87 and lm90 drivers for board temperature/power monitoringBen Hutchings2008-11-068-64/+265
| | | | | | | | | Add board monitoring to periodic work whenever link is down. For SFE4001, report when a fault has caused the PHY to turn off. For SFE4002, switch XFP PHY into low-power state in case of a fault. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Expose flash region storing boot code as MTDBen Hutchings2008-11-069-7/+327
| | | | | | | | | The boot code that appears as a PCI expansion ROM on the SFC4000 is stored in flash. Expose this as a standard MTD device to allow for in-place upgrades. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Clean up non-volatile memory partitioningBen Hutchings2008-11-064-11/+24
| | | | | | | | | | Move flash and EEPROM partition boundary constants into spi.h and rename them to be consistent. Add a comment on the partitioning. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sfc: Correct address of gPXE boot configuration in EEPROMBen Hutchings2008-11-061-2/+2
| | | | | | | | | Due to a hardware bug, the originally assigned range cannot reliably be used for boot configuration and must not be modifiable through ethtool. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* drivers/net: Kill now superfluous ->last_rx stores.David S. Miller2008-11-041-1/+1
| | | | | | | | | | | | | The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Drivers need not do it any more. Some cases had to be skipped over because the drivers were making use of the ->last_rx value themselves. Signed-off-by: David S. Miller <davem@davemloft.net>
* net: convert print_mac to %pMJohannes Berg2008-10-281-9/+6
| | | | | | | | | | | | This converts pretty much everything to print_mac. There were a few things that had conflicts which I have just dropped for now, no harm done. I've built an allyesconfig with this and looked at the files that weren't built very carefully, but it's a huge patch. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-15 23:27:03 +0100