summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/intel/iwlwifi/iwl-config.h (follow)
Commit message (Collapse)AuthorAgeFilesLines
* iwlwifi: mvm: rs: add logs for the wrong antenna caseGregory Greenman2017-06-221-0/+1
| | | | | | | | | In case that rate's antenna is wrong at the init stage, it's very hard to say what went wrong. Add debug data to the already existing WARN_ON_ONCE. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add 9000 and A000 device familiesSara Sharon2017-06-051-0/+2
| | | | | | | Add two new device families to differentiate them from 8000. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add dbgc_supported to transport configurationSara Sharon2017-06-051-1/+2
| | | | | | | | Use transport configuration to determine DBGC support instead of relying on device family. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: remove references to 8000 B-step devicesSara Sharon2017-06-051-1/+0
| | | | | | | | | | We don't have any 8000 B-step right now, and there is no firmware loading code for them anyway. Further more, 9000 B-step devices will hit those code paths. Remove code that was introduced only for 8000 B-step. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: cleanup references to 8000 family in NVM codeSara Sharon2017-06-051-1/+3
| | | | | | | | | | NVM code is tightly coupled with 8000 family, while it really refers to extended NVM format introduced back then. Separate it to a configuration dependent boolean, and rename defines accordingly. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: Add fw_name_pre_rf_next_step to support different rf stepsHaim Dreyfuss2017-06-021-0/+3
| | | | | | | | | | Integrated chip may have different HW and RF steps. Currently, the driver supports only different HW steps. Add logic to support different RF steps enables combining different HW and RF steps. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: move to 512 queuesSara Sharon2017-04-251-1/+1
| | | | | | | | Avoid using the old define since it will enlarge necessary structs for previous HW. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: support a000 CDB productSara Sharon2017-04-191-1/+4
| | | | | | | Identify and load FW for a000 CDB product. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: cleanup unused functionSara Sharon2017-04-191-10/+0
| | | | | | | iwl_has_secure_boot() isn't getting called anywhere. Clean it up. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: pcie: introduce split point to a000 devicesSara Sharon2017-04-111-1/+3
| | | | | | | | | | | | | | a000 devices are going to have a lot of flows simplified and changed: init flow, RX, TX, and more. This, combined with the fact that code is already very complicated due to backward compatibility - introduce a split that will enable to introduce simplified version of functions. Shared ops are moved to a macro, while functions that will be updated in the next patches are defined twice for now. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add support for 9000 HW B-step NICsLiad Kaufman2017-04-111-2/+5
| | | | | | | | Once we remove support for A-step, we'll be able to clean the code back again. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: remove support for deprecated RFLuca Coelho2017-04-111-1/+0
| | | | | | | One of the RF modules we support has been deprecated and never released publicly. Remove support for this module. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: support two phys for a000 devicesSara Sharon2017-02-061-1/+2
| | | | | | | | | | Support differentiating between two phys for a000 devices in order to load the correct firmware. Eventually when moving completely to the new phy we will be able to remove this. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: mvm: cleanup redundant no_power_up_nic_in_init configSara Sharon2016-09-221-1/+0
| | | | | | | This is never really used anymore. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add the new 8275 seriesOren Givon2016-09-161-0/+1
| | | | | | | | Add a new config struct for the new 8275 series and add the first PCI ID for it. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add the new 9560 seriesOren Givon2016-09-161-0/+1
| | | | | | | | Add a new config struct for the new 9560 series and add the 4 new PCI IDs for it. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add the new 9170 seriesOren Givon2016-08-301-0/+1
| | | | | | | | Add a new config struct for the new 9170 series and add the first PCI ID for it. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add the new 9270 seriesOren Givon2016-08-301-0/+1
| | | | | | | | Add a new config struct for the new 9270 series and add the first PCI ID for it. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: add a new series 9460 with new PCI IDOren Givon2016-08-301-1/+1
| | | | | | | | Add a new series to the 9000 series called 9460. In addition, add a new PCI ID that is the 9460 new series. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: rename and reorder 9000 series configuration structsOren Givon2016-08-301-2/+2
| | | | | | | | Rename and reorder the 9000 series configuration structs: - struct containing configuration of 5165 was renamed to 9000. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: pcie: initialize a000 device's TFD tableSara Sharon2016-07-061-1/+2
| | | | | | | | | | | | For a000 device the FH was replaced by the TFH. This is the first patch in a series introducing the changes stemming from this change. This patch initializes the TFQ queue table with the new 64 bit register and the relevant TFH configuration registers. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: remove iwl_ht_params.smps_modeJohannes Berg2016-07-061-3/+3
| | | | | | | | | | This struct member is never set, so remove it. Since this is the last thing that needs mac80211.h, also change the includes to no longer use mac80211.h Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: Add a000 HW family supportHaim Dreyfuss2016-07-061-0/+2
| | | | | | | Add a000 family configuration to iwl-cfg struct Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: pcie: workaround HW shadow registers bugSara Sharon2016-07-011-1/+3
| | | | | | | | | | | | | | | | | | | Integrated 9000 devices have a bug with shadow registers value retention. If driver writes RBD registers while MAC is asleep the values are stored in shadow registers to be copied whenever MAC wakes up. However, in 9000 devices a MAC wakeup is not triggered and when the bus powers down due to inactivity the shadow values and dirty bits are lost. Turn on the chicken-bits that cause MAC wakeup for RX-related values as well when the device is in D0. When the device is in low power mode turn the RX wakeup chicken bits off since driver is idle and this W/A is not needed. Remove previous W/A which was ineffective. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: make configuration structs smallerJohannes Berg2016-05-101-57/+61
| | | | | | | | | Since we have a lot of configuration structs (almost 70) saving some memory in each one of them leads to an overall saving of ~2.6KiB of memory. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: allow combining different phy images with mac imagesHaim Dreyfuss2016-05-101-0/+3
| | | | | | | | | | Currently there is one to one function between device id to it's ucode. The new generation devices allows to combine different phy and mac images. Now we have two different ucode images with the same device id. Read RF ID to identify phy image and overwrite it if needed. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: Rename 9560 to 9260 and add new PCI IDs for itHaim Dreyfuss2016-05-101-1/+1
| | | | | | | | | Rename 9560 to 9260. Add new PCI ID for 9260 and change some entries from 5165 to 9260. Also order the 9000 series. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* iwlwifi: Edit the 8265 SDIO IDMordechai Goodstein2016-05-101-0/+1
| | | | | | | Add new 8265 series SDIO ID. Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* cfg80211: remove enum ieee80211_bandJohannes Berg2016-04-121-1/+1
| | | | | | | | | This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* iwlwifi: remove IWL_*_UCODE_API_OKEmmanuel Grumbach2016-03-301-3/+0
| | | | | | | | | | | _UCODE_API_OK was a intermediate version between MIN and MAX. If a user had a firmware below _OK but above _MIN, the driver would work but the user would get a warning in the kernel log telling him to update his firmware. This is not needed since most users won't look for these messages in the kernel log if their wifi is working. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: mvm: enable TCP/UDP checksum support for 9000 familySara Sharon2016-03-301-0/+2
| | | | | | | | | Declare and enable support of RX and TX checksum for 9000 family. Configure offload_assist in the TX cmd accordingly to support TX csum. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: 9000: update device id and FW serial numberHaim Dreyfuss2016-03-301-1/+1
| | | | | | | | | Update device id and FW serial number for 2X2 antenna devices in 9000 generation product. These will not be available on the market in the coming year. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: add support for getting HW address from CSRSara Sharon2016-03-091-0/+2
| | | | | | | | | | | | | From 9000 family on, we need to get HW address from host CSR registers. OEM can override it by fusing the override registers - read those first, and if those are 0 - read the OTP registers instead. In addition - bail out if no valid mac address is present. Make it shared for all NICs. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: mvm: enable VHT MU-MIMO for supported hardwareSara Sharon2016-02-271-0/+2
| | | | | | | | Incoming hardware will support VHT MU-MIMO. Declare this capability for relevant hardware. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: pcie: add 9000 series multi queue rx DMA supportSara Sharon2016-01-311-0/+2
| | | | | | | | | | | | | | | | | | | | | The 9000 series introduces several changes in the device DMA operation. As the device now supports multi-queue rx, several DMA channels should be configured. The flows of providing the device with the allocated RBDs now changes as well - the device maintains a separate table of used and free table. The hardware may use the free table to feed RBDs to any queue. This requires maintaing a shared table to map returned RBDs to the original RXB - for that purpose the VID is introduced - an internal identifier of the RB placed in the lower 12 bits and returned by HW in the used data. Another change is the support of 64 bit DMA address. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: change the Intel Wireless email addressEmmanuel Grumbach2015-12-201-1/+1
| | | | | | | ilw@linux.intel.com is not available anymore. linuxwifi@intel.com should be used instead. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: Add PCI IDs for the new series 8165Oren Givon2015-12-011-0/+1
| | | | | | | | Add a new struct for the 8165 series and a few new PCI ID entries. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: Add PCI IDs for the new 3168 seriesOren Givon2015-12-011-0/+1
| | | | | | | | Add a new struct for the 3168 series and a few new PCI ID entries. Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: Add new PCI IDs for 9260 and 5165 seriesDreyfuss, Haim2015-12-011-0/+3
| | | | | | | | | | | | | | | Add 9000-family configuration to iwl_cfg struct Add a new struct to define the 5165 series. Rename the struct that defines the 9000 series to 9260. Add some new sub-system IDs for the 9260 and 5165 series. For 9260: 0x0A10, 0x0000, 0x0510, 0x0710, 0x0410, 0x0610. For 5165: 0x2A10, 0x2010, 0x0310, 0x0210. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: mvm: remove redundant d0i3 flag from the config structLuca Coelho2015-11-261-2/+0
| | | | | | | | | The d0i3 flag in the device configuration structure is redundant, because the same information can be determined by checking the firmware capability flag. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* iwlwifi: move under intel vendor directoryKalle Valo2015-11-181-0/+437
Part of reorganising wireless drivers directory and Kconfig. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-15 14:03:54 +0100