| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Hans de Goede identified a bug in p54p_check_tx_ring:
there are two ring indices. 1 => tx data and 3 => tx management.
But the old code had a constant "1" and this resulted in spurious
dma unmapping failures.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| |\|
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| |\|
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| |\ \ |
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
iwl-devtrace.h is used to declare and define trace points and
including iwl-dev.h from the file, which in turn includes other
generic headers, can lead to problems like generating duplicate copies
of generic trace points depending on the order of includes. Don't
include iwl-dev.h from iwl-devtrace.h but include it from its users -
iwl-io.h and iwl-devtrace.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
|
| |\ \ \ \
| | |_|/
| |/| |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| |\| | |
| |_|/
|/| |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Below warning is triggered sometimes at module removal time when
CONFIG_DMA_API_DEBUG is enabled. This should be caused by we didn't
unmap pending commands (enqueued, but no complete notification
received) for the Tx command queue.
[ 1583.107469] ------------[ cut here ]------------
[ 1583.107539] WARNING: at lib/dma-debug.c:688
dma_debug_device_change+0x13c/0x180()
[ 1583.107617] Hardware name: ...
[ 1583.107664] pci 0000:04:00.0: DMA-API: device driver has pending DMA
allocations while released from device [count=1]
[ 1583.107713] Modules linked in: ...
[ 1583.111661] Pid: 16970, comm: modprobe Tainted: G W
2.6.34-rc1-wl #33
[ 1583.111727] Call Trace:
[ 1583.111779] [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111833] [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111908] [<c0138e11>] warn_slowpath_common+0x71/0xd0
[ 1583.111963] [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.112016] [<c0138ebb>] warn_slowpath_fmt+0x2b/0x30
[ 1583.112086] [<c02a281c>] dma_debug_device_change+0x13c/0x180
[ 1583.112142] [<c03e6c33>] notifier_call_chain+0x53/0x90
[ 1583.112198] [<c03e1ebe>] ? down_read+0x6e/0x90
[ 1583.112271] [<c015b229>] __blocking_notifier_call_chain+0x49/0x70
[ 1583.112326] [<c015b26f>] blocking_notifier_call_chain+0x1f/0x30
[ 1583.112380] [<c031931c>] __device_release_driver+0x8c/0xa0
[ 1583.112451] [<c03193bf>] driver_detach+0x8f/0xa0
[ 1583.112538] [<c0318382>] bus_remove_driver+0x82/0x100
[ 1583.112595] [<c0319ad9>] driver_unregister+0x49/0x80
[ 1583.112671] [<c024feb2>] ? sysfs_remove_file+0x12/0x20
[ 1583.112727] [<c02aa292>] pci_unregister_driver+0x32/0x80
[ 1583.112791] [<fc13a3c1>] iwl_exit+0x12/0x19 [iwlagn]
[ 1583.112848] [<c017940a>] sys_delete_module+0x15a/0x210
[ 1583.112870] [<c015a5db>] ? up_read+0x1b/0x30
[ 1583.112893] [<c029600c>] ? trace_hardirqs_off_thunk+0xc/0x10
[ 1583.112924] [<c0295ffc>] ? trace_hardirqs_on_thunk+0xc/0x10
[ 1583.112947] [<c03e6a1f>] ? do_page_fault+0x1ff/0x3c0
[ 1583.112978] [<c03e36f6>] ? restore_all_notrace+0x0/0x18
[ 1583.113002] [<c016aa70>] ? trace_hardirqs_on_caller+0x20/0x190
[ 1583.113025] [<c0102d58>] sysenter_do_call+0x12/0x38
[ 1583.113054] ---[ end trace fc23e059cc4c2ced ]---
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| |\| |
| |/
|/|
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The libertas driver calls wiphy_unregister() without a prior
wiphy_register() when a devices fails initialization. Fix this by
introducing a private flag.
[ 9.310000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
[ 9.330000] [<c0311310>] (wiphy_unregister+0xfc/0x19c) from [<bf00c9ec>] (lbs_cfg_free+0x70/0x9c [libertas])
[ 9.330000] [<bf00c9ec>] (lbs_cfg_free+0x70/0x9c [libertas]) from [<bf014fdc>] (lbs_remove_card+0x180/0x210 [libertas])
[ 9.330000] [<bf014fdc>] (lbs_remove_card+0x180/0x210 [libertas]) from [<bf035394>] (if_sdio_probe+0xdc4/0xef4 [libertas_sdio])
[ 9.330000] [<bf035394>] (if_sdio_probe+0xdc4/0xef4 [libertas_sdio]) from [<c0230d14>] (sdio_bus_probe+0xd4/0xf0)
[ 9.330000] [<c0230d14>] (sdio_bus_probe+0xd4/0xf0) from [<c01a6034>] (driver_probe_device+0xa4/0x174)
[ 9.330000] [<c01a6034>] (driver_probe_device+0xa4/0x174) from [<c01a6164>] (__driver_attach+0x60/0x84)
[ 9.330000] [<c01a6164>] (__driver_attach+0x60/0x84) from [<c01a5854>] (bus_for_each_dev+0x4c/0x8c)
[ 9.330000] [<c01a5854>] (bus_for_each_dev+0x4c/0x8c) from [<c01a50e4>] (bus_add_driver+0xa0/0x228)
[ 9.330000] [<c01a50e4>] (bus_add_driver+0xa0/0x228) from [<c01a6470>] (driver_register+0xc0/0x150)
[ 9.330000] [<c01a6470>] (driver_register+0xc0/0x150) from [<bf03a06c>] (if_sdio_init_module+0x6c/0x108 [libertas_sdio])
[ 9.330000] [<bf03a06c>] (if_sdio_init_module+0x6c/0x108 [libertas_sdio]) from [<c00263ac>] (do_one_initcall+0x5c/0x1bc)
[ 9.330000] [<c00263ac>] (do_one_initcall+0x5c/0x1bc) from [<c0069f80>] (sys_init_module+0xc0/0x1f0)
[ 9.330000] [<c0069f80>] (sys_init_module+0xc0/0x1f0) from [<c0026f00>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
GFP_KERNEL);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c67bd55e93348f160d590ff9edf08904 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Stable <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Recent bug reports have shown that rt2500usb also suffers from the
powersave problems that the PCI rt2x00 drivers suffer from.
So disable powersaving by default for rt2500usb as well.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| | |
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Previously in interrupt handling tasklet, iwlwifi driver only clear/ack
those interrupts that are enabled by the driver through inta_mask.
If the hardware generates unattended interrupts, driver will not ack them,
defeating the interrupt coalescing feature. This results in high number
of interrupts per second and high CPU utilization.
This patch addresses this issue by acking those unattended interrupts
in the tasklet. Local test showed an order of magnitude improvement
in terms of the number of interrupts without sacrificing networking
throughput. This is a workaround for hardware issue.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Forget one hunk in 4965 during "iwlwifi: error checking for number of tfds
in queue" patch.
Reported-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit "cfg80211: convert bools into flags" mistakenly modified iwlwifi's
regulatory settings instead of just converting it. Fix this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2172
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Thanks to Chris Chabot for giving his old wireless usb dongle to me
to test it under Linux.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Benjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| | |
This patch adds support for the NEC WL300NU-G USB wifi dongle.
Signed-off-by: Ben Konrath <ben@bagu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| |\|
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit a239a8b47cc0e5e6d7416a89f340beac06d5edaa introduced a
noisy message, that fills up the log very fast.
The error seems not to be fatal (the connection is stable and
performance is ok), so make it IWL_DEBUG_TX rather than IWL_ERR.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable@kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When I initially stumbled upon sequence number problems with PAE frames
in ath9k, I submitted a patch to remove all special cases for PAE
frames and let them go through the normal transmit path.
Out of concern about crypto incompatibility issues, this change was
merged instead:
commit 6c8afef551fef87a3bf24f8a74c69a7f2f72fc82
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Tue Feb 9 10:07:00 2010 +0530
ath9k: Fix sequence numbers for PAE frames
After a lot of testing, I'm able to reliably trigger a driver crash on
rekeying with current versions with this change in place.
It seems that the driver does not support sending out regular MPDUs with
the same TID while an A-MPDU session is active.
This leads to duplicate entries in the TID Tx buffer, which hits the
following BUG_ON in ath_tx_addto_baw():
index = ATH_BA_INDEX(tid->seq_start, bf->bf_seqno);
cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
BUG_ON(tid->tx_buf[cindex] != NULL);
I believe until we actually have a reproducible case of an
incompatibility with another AP using no PAE special cases, we should
simply get rid of this mess.
This patch completely fixes my crash issues in STA mode and makes it
stay connected without throughput drops or connectivity issues even
when the AP is configured to a very short group rekey interval.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In case debugfs does not init for some reason (or is disabled
on older kernels) driver does not allocate stats.fw_stats
structure, but tries to clear it later and trips on a NULL
pointer:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
PC is at __memzero+0x24/0x80
Backtrace:
[<bf0ddb88>] (wl1251_debugfs_reset+0x0/0x30 [wl1251])
[<bf0d6a2c>] (wl1251_op_stop+0x0/0x12c [wl1251])
[<bf0bc228>] (ieee80211_stop_device+0x0/0x74 [mac80211])
[<bf0b0d10>] (ieee80211_stop+0x0/0x4ac [mac80211])
[<c02deeac>] (dev_close+0x0/0xb4)
[<c02deac0>] (dev_change_flags+0x0/0x184)
[<c031f478>] (devinet_ioctl+0x0/0x704)
[<c0320720>] (inet_ioctl+0x0/0x100)
Add a NULL pointer check to fix this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| |\|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
|
| | |\
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit 21b2d8bd2f0d4e0f21ade147fd193c8b9c1fd2b9.
As explained by Johannes:
When we
build a probe request frame in the buffer with the SSID, we could
arrive over the limit of 200 bytes. When we build it in the buffer
without the SSID (wildcard) we don't arrive over 200 bytes, but the
ucode still allows direct probe in addition because it has an internal
buffer that is larger when it inserts the SSID...
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Recent patch "iwlwifi: move 3945 clip groups to 3945 data" exposed a memory
corruption problem. When initializing the clip groups the code was
mistakenly using the iwlagn rate count, not the 3945 rate count. This
resulted in more memory being written than was allocated.
"iwlwifi: move 3945 clip groups to 3945 data" moved the location where the
clip groups are stored and the impact is now severe in that the number of
configured TX queues is modified. Previously the
"temperature" field was overwritten, which did not seem to affect the
operation.
Fix this one instance where wrong rate count was used. I also noticed one
more location where the iwlagn rate count was used to index an iwl3945
array, fix this. I also modified one location that modified the iwlagn rate
count to obtain the iwl3945 rate count ... just use the iwl3945 rate count
directly.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2165 and
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2168
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fixed below compiler warning:
drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.
also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.
1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd0f798b71b1590e7aca6647f2caef1649)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.
2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.
3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.
4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp. AR5K_STA_ID1_DEFAULT_ANTENNA).
also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.
this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.
The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
My previous patch (655ffee284dfcf9a24ac0343f3e5ee6db85b85c5) added locking in
a bad way. Because rndis_set_oid can sleep, there is need to prepare multicast
addresses into local buffer under netif_addr_lock first, then call
rndis_set_oid outside. This caused reorganizing of the whole function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
