| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix up USB drivers that return an errno value (result of usb_submit_urb())
to qdisc_restart(), causing qdisc_restart() to print a warning and requeue/
retransmit the skb.
- hso: skb is freed: use after free
- at76_usb: skb is freed: use after free
Compile tested only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Fix up hamradio drivers that return an errno value to dev_queue_xmit(), causing
it to print a warning an free the skb.
- bpqether: skb is freed: use after free
Compile tested only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Fix up WAN drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- cycx_x25: intention appears to be to requeue the skb
Does not compile cleanly for me even without this patch, so untested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
net: fix network drivers ndo_start_xmit() return values (part 3)
Fix up wireless drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- airo: transmission not implemented for chip, intention is to free and abort
- ipw2200: transmission not implemented for promiscous mode, intention is to
drop
- prism54: intention is to drop
- wl3501_cs: intention appears to be to drop
- zd1201: error counter indicates intention is to drop
All drivers compile tested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix up IRDA drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- donauboe: intention appears to be to have the skb retransmitted without
error message
- irda-usb: intention is to drop silently according to comment
- kingsub-sir: skb is freed: use after free
- ks959-sir: skb is freed: use after free
- ksdazzle-sir: skb is freed: use after free
- mcs7880: skb is freed: use after free
All but donauboe compile tested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Fix up drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning and requeue/retransmit the skb.
- xpnet: memory allocation error, intention is to drop
- ethoc: oversized packet, packet must be dropped
- ibmlana: skb freed: use after free
- rrunner: skb freed: use after free
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
We need to enforce the IP alignment on the non-mergeable RX path just
like the other RX path. Not doing so results in misaligned IP
headers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
Some drivers incorrectly use ntohs() instead of htons()
A cleanup as htons() returns same result than ntohs(),
but better to use the proper one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
SH4's BUG() seems to confuse the compiler as it is considered to
return; thus, some functions would trigger usage of uninitialized
variables or non-void functions returning void.
Work around by initializing/returning.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the i2400m device resets, the driver code will force some
functions to return a -ERESTARTSYS error code, which can is used by
the caller to determine which recovery actions to take.
However, in certain situations the only thing that can be done is to
bubble up said error code to user space, for handling.
However, -ERESTARSYS was a poor choice, as it is supposed to be used
by the kernel only.
As such, replace -ERESTARTSYS with -EL3RST; as well, in
i2400m_msg_to_dev(), when the device is in boot mode (following a
recent reset), return -EL3RST instead of -ENODEV (meaning the device
is in bootrom mode after a reset, not that the device was
disconnected, and thus, normal commands cannot be executed).
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When a device reset happens during firmware load [in
i2400m_dev_bootstrap()], __i2400m_dev_start() will retry a number of
times. However, for those retries to be able to accomplish anything,
the device's bootrom has to be reinitialized.
Thus, on the retry path, pass the I2400M_MAC_REINIT to the firmware
load code.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The current SDIO code was working in polling mode for boot-mode
(firmware load) mode. This was causing issues on some hardware.
Moved all the RX code to use a unified IRQ handler that based on the
type of data the device is sending can discriminate and decide which
is the right destination.
As well, all the reads from the device are made to be at least the
block size (256); the driver will ignore the rest when not needed.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When i2400m_bootrom_init() fails to put the device into a state of
being ready to accept firmware, the driver was currently trying to
reset it if it failed to do so. This is not too useful; as part of
trying to put the device in the right state a few resets have already
been tried.
At this point, things are probably fried out and an extra reset might
do more harm than good (for example causing reseting of other
functions in the same composite device).
So it is left up to the callers to determine the error path to take
(at the end this is always i2400m_setup(), who depending on how many
retries are left, might give up on the device).
From a fix by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| | |
Add a poke table for the SDIO device (as it is different than USB).
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This change moves the table of "pokes" performed on the device at boot
time to the bus specific portion of the driver.
Different models of the i2400m device supported by this driver require
different poke tables, thus having a single table that works for all
is impossible. For that, the table is moved to the bus-specific
driver, who can decide which table to use based on the specifics of
the device and point the generic driver to it.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The code that sets up the i2400m (firmware load and general driver
setup after it) includes a couple of retry loops.
The SDIO device sometimes can get in more complicated corners than the
USB one (due to its interaction with other SDIO functions), that
require trying a few more times.
To solve that, without having a failing USB device taking longer to be
considered dead, allow the retry counts to be specified by the
bus-specific driver, which the general driver takes as a parameter.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When a device reboot happens when we are under probe, with init_mutex
taken, make sure we can recover. Have dev_reset_handle set boot mode
and i2400m_msg_to_dev() will see it and fail gracefully instead of
timing out.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the TX FIFO filled up and i2400m_tx_new() failed to allocate a
new TX message header, a missing check for said condition was causing a
kernel oops when trying to dereference a NULL i2400m->tx_msg pointer.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
i2400m_dev_shutdown() tried to reset the device to put it in a known
state before shutting down.
But that turned out to be pointless. We reach this case in two paths:
1 - when the device resets, to clean up state
2 - when the driver is unloaded, for the same
however, in both cases it is pointless; in (1) the device is already
reset, why do it again? in (2) we can't -- the USB stack, for example,
doesn't allow communicating with the device when the driver is being
unbound and if the device is disconnected, the device is gone already.
So just remove it. Leave the function as a placeholder for future
cleanups that will be done from data allocated by the driver during
device operation.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
i2400m_tx_skip_tail() needs to handle the special case of being called
when the tail room that is left over in the FIFO is zero.
This happens when a TX message header was opened at the very end of
the FIFO (without payloads). The i2400m_tx_close() code already marked
said TX message (header) to be skipped and this function should be
doing nothing.
It is called anyway because it is part of a common "corner case" path
handling which takes care of more cases than only this one.
The tail room computation was also improved to take care of the case
when tx_in is at the end of the buffer boundary; tail_room has to be
modded (%) to the buffer size. To do that in a single well-documented
place, __i2400m_tx_tail_room() is introduced and used.
Treat i2400m->tx_in == 0 as a corner case and handle it accordingly.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In some situations, when a new TX message header is started, there
might be no space for data payloads. In this case the message is left
with zero payloads and the i2400m_tx_close() function has just to mark
it as "to skip". If it tries to go ahead it will overwrite things
because there is no space to add padding as defined by the
bus-specific layer. This can cause buffer overruns and in some stress
cases, panics.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| | |
The constant is being use as an alignment factor, not as a padding
factor; made reading/reviewing the code quite confusing.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This reset type causes the WiMAX function to be disabled and
re-enabled, which will force the WiMAX device to reset and enter boot
mode.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
|
| | |
| |
| |
| |
| |
| |
| | |
Changing debug level of print out to support validation engineers
getting the messages they need.
Signed-off-by: <dirk.j.brandewie@intel.com>
|
| | |
| |
| |
| |
| |
| |
| | |
By mistake, the BUG_ON() check was left in there and it will fail when
called if i2400m->work_queue is still not setup.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
RX support is the only user of the work-queue, to process
reports/notifications from the device. Thus, it needs the work queue
to be initialized first.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Reported and fixed by Cindy H Kao.
When the device is stopped __i2400m_dev_stop() stops the network
queue.
However, when this is done in the middle of heavy network operation,
when the bus-specific subdriver is still wrapping up and it reports a
sent TX transaction with _tx_msg_sent() right after the device was
stopped, the queue was being started again, which was causing a stream
of oopsen and finally a panic.
In any case, said call has no place there. It's a left over from an
early implementation that was discarded later on.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The i2400m driver waits for the device to report being ready for
entering power save before asking it to do so. This module parameter
allows control of said operation; if disabled, the driver won't ask
the device to enter power save mode.
This is useful in setups where power saving is not so important or
when the overhead imposed by network reentry after power save is not
acceptable; by combining this with parameter 'idle_mode_disabled', the
driver will always maintain both the connection and the device in
active state.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Some users still load bond module multiple times to create bonding
devices. This accidentally was broken by a later patch about
the time sysfs was fixed. According to Jay, it was broken
by:
commit b8a9787eddb0e4665f31dd1d64584732b2b5d051
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Fri Jun 13 18:12:04 2008 -0700
bonding: Allow setting max_bonds to zero
Note: sysfs and procfs still produce WARN() messages when this is done
so the sysfs method is the recommended API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
In the tx queue destroy path, be_tx_q_clean() is currently called after the tx queues are freed; it must be called before.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
be_rx_compl_get() must not reset(via the valid word) the rx_compl as the rx_compl is not processed yet; it must be reset after it is processed.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
rx stats are not getting updated when an rx_compl with only one frag is rcvd in non-lro path.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Fix netdev stat rx_errors to cover length related errors and checksum errors and rx_dropped to the pkts dropped due to lack of buffers
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
Use cancel_delayed_work_sycn instead of cancel_delayed_work() to reliably kill be_worker() as it rearms itself.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pre-allocate a skb at init time to be used for control messages to the HW
if skb allocation fails.
Tolerate failures to send messages initializing some memories at the cost of
parity error detection for these memories.
Retry sending connection id release messages if both alloc_skb(GFP_ATOMIC)
and alloc_skb(GFP_KERNEL) fail.
Do not bring the interface up if messages binding queue set to port fail to
be sent.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
rtl8169_tx_interrupt() is used from NAPI context, it can
directly free skbs. dev_kfree_skb_irq() is a leftover from
pre-NAPI times of this driver.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| | |
This is available in a standard MDIO register in 10GBASE-T PHYs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
RX buffer rings can be comprised of non-contiguous fixed
size chunks of memory. The ring is given to the hardware
as a pointer to a location that stores the location of
the queue. If the queue is greater than 4096 bytes then
the hardware gets a list of said pointers.
This patch addes the necessary logic to generate the list if
the queue size exceeds 4096.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |/
|
|
|
|
|
|
| |
The alignment was on size of queue boundary, but the hardware
only requires 4-byte alignment.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
The WAKE_MCAST bit is tested twice, the first should be WAKE_UCAST.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <csnook@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Add a configurable Descriptor Skip Length for systems that lack cache
coherence.
(akpm: I think this should be done as a module parameter, not a
compile-tinme option)
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13348
akpm: the reporter disappeared, so I typed it in again.
It is not possible to make clone of tagged VLAN interface to be used as
mac-based vlan interfave.
How reproducible:
Use any 802.1q tagged vlan interface, e.g. eth2.700 and clone it:
ip link add link eth2.700 address 00:04:75:cb:38:09 macvlan0 type macvlan
ip link set dev macvlan0 up
ip addr add 10.195.1.1/24 dev macvlan0
So far, so good. Now try to ping anything via macvlan0:
ping 10.195.1.2
Actual results:
For every attempted packet tx kernel writes to console:
------------[ cut here ]------------
WARNING: at net/8021q/vlan_dev.c:254 vlan_dev_hard_header+0x36/0x126 [8021q]()
Hardware name: M22ES
Modules linked in: arptable_filter arp_tables bridge veth macvlan arc4 ecb
ppp_mppe ppp_async crc_ccitt ppp_generic slhc autofs4 sunrpc 8021q garp stp
ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_tcpudp
x_tables dm_mirror dm_region_hash dm_log dm_multipath dm_mod sbs sbshc lp
floppy snd_intel8x0 joydev snd_seq_dummy snd_intel8x0m snd_ac97_codec
ide_cd_mod ac97_bus snd_seq_oss cdrom snd_seq_midi_event serio_raw snd_seq
snd_seq_device snd_pcm_oss snd_mixer_oss parport_pc snd_pcm parport battery
8139cp snd_timer i2c_sis96x ac button snd rtc_cmos rtc_core 8139too soundcore
rtc_lib mii i2c_core pcspkr snd_page_alloc pata_sis libata sd_mod scsi_mod ext3
jbd ehci_hcd ohci_hcd uhci_hcd [last unloaded: ip_tables]
Pid: 0, comm: swapper Tainted: G W 2.6.29.3 #1
Call Trace:
[<c0425f48>] warn_slowpath+0x60/0x9f
[<c0425f6f>] warn_slowpath+0x87/0x9f
[<dffb850d>] vlan_dev_hard_header+0x0/0x126 [8021q]
[<dffb8543>] vlan_dev_hard_header+0x36/0x126 [8021q]
[<dffb850d>] vlan_dev_hard_header+0x0/0x126 [8021q]
[<df83155d>] macvlan_hard_header+0x3c/0x47 [macvlan]
[<df831521>] macvlan_hard_header+0x0/0x47 [macvlan]
[<c062bf3f>] arp_create+0xef/0x1ff
[<c062c08c>] arp_send+0x3d/0x54
[<c062c916>] arp_solicit+0x16c/0x177
[<c05fadd2>] neigh_timer_handler+0x227/0x269
[<c05fabab>] neigh_timer_handler+0x0/0x269
[<c042ce4d>] run_timer_softirq+0xf0/0x141
[<c0429e5a>] __do_softirq+0x76/0xf8
[<c0429de4>] __do_softirq+0x0/0xf8
<IRQ> [<c044fb67>] handle_level_irq+0x0/0xad
[<c0429db7>] irq_exit+0x35/0x62
[<c04046bb>] do_IRQ+0xdf/0xf4
[<c04035a7>] common_interrupt+0x27/0x2c
[<c04079c5>] default_idle+0x2a/0x3d
[<c0401bb6>] cpu_idle+0x57/0x70
Macvlan driver always uses standard ethernet header length for all types
of interface to which it is linked. This patch fixes this problem.
Reported-by: <sg.tweak@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Restore support for cards with MII-lacking PHYs as compared to removed
pre-2.6.29 eepro100 driver: use full low-level MII I/O access abstraction
by providing clean PHY-specific mdio_ctrl() functions for either standard
MII-compliant cards, slightly special ones or non-MII PHY ones.
We now have another netdev_priv member for mdio_ctrl(), thus we have some
array indirection, but we save some additional opcodes for specific
phy_82552_v handling in the common case.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
