| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:
1) The original code drops all packets with a multicast destination address,
even though neighbor solicitations are sent to the solicited-node
address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
solicited node address, rather than the target address from the
neighbor solicitation. So neighbor lookups would always fail if it
got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
The context for neigh_reduce() is the transmit path, vxlan_xmit(),
where the host or a bridge-attached neighbor is trying to transmit
a neighbor solicitation. To respond to it, the tunnel endpoint needs
to do a *receive* of the appropriate neighbor advertisement. Doing a
send, would only try to send the advertisement, encapsulated, to the
remote destinations in the fdb -- hosts that definitely did not do the
corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
isrouter flag in the advertisement. This has nothing to do with whether
or not the target is a router, and generally won't be set since the
tunnel endpoint is bridging, not routing, traffic.
The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.
1) Freeing the interrupts. The current code will not free all interrupts
that were requested by the driver. Furthermore, the code tries to do a
platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
iteration.
This patch fixes these bugs.
2) Wrong order of err: and rollback: labels. If the setup of the PHY in
the code fails, the interrupts that have been requested before are
not freed:
request irq
if requesting irqs fails, goto rollback
setup phy
if phy setup fails, goto err
return 0
rollback:
free irqs
err:
This patch brings the code into the correct order.
3) The code calls napi_enable() and emac_int_enable(), but does not
undo both in case of an error.
This patch adds calls of emac_int_disable() and napi_disable() to the
rollback code.
4) RX DMA descriptors are not freed in case of an error: Right before
requesting the irqs, the function creates DMA descriptors for the
RX channel. These RX descriptors are never freed when we jump to either
rollback or err.
This patch adds code for freeing the DMA descriptors in the case of
an initialization error. This required a modification of
cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
function to free the DMA descriptors while the DMA channels are
in IDLE state (before cpdma_ctlr_start() was called).
Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In commit 6892b41d9701283085b655c6086fb57a5d63fa47
Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date: Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api
the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.
This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47dc (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
| |
Currently, via-rhine fails to call pci_disable_device() for errors
in rhine_init_one().
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)
@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
This patch fixes a NULL pointer dereference in the event of an
skb allocation failure in arp_reduce().
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
| |
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is a context modified revert of commit 6a9612e2cb22
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb22 ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.
[ 18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[ 19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[ 19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[ 19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
dma_set_mask and dma_set_coherent_mask.
2. For the 32 bits dma mask dma_set_coherent_mask is only called if
dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
call to dma_set_mask_and_coherent.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull these last(?) few wireless bits intended for the 3.14
stream. Each is here to address a problem found with a patch already
merged...
Dave Jones gives us a memory leak fix, for an error path in brcmfmac.
Felix Fietkau moves a small delay to make it actually reachable.
Helmut Schaa fixes an ath9k sequence numbering problem for non-data
frames.
Stanislaw Gruszka reverts an earlier fix that was found to cause
random connection drops on RT5390 PCI adapters
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit eac40d9631a7db43570df859fa8a9922e9623607. It cause
random connection drops on RT5390 PCI adapters.
On Mediatek there is different driver version available for RT53xx chip
based on bus type (2.5.0.3 for PCI and 2.6.1.3 for USB). Hence possibly
we should set registers differently based on bus type. But is also
possible that new driver (i.e. 2.6.1.3) was not verified on RT53xx USB.
Until we figure out how to initialize registers properly for RT53xx just
revert commit eac40d9631a7db43570df859fa8a9922e9623607 since it cause
regression.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since commit 558ff225de80ac95b132d3a115ddadcd64498b4f (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit 1eb4301867 (brcmfmac: fix txglomming scatter-gather packet transfers)
added an allocation of an skb via brcmu_pkt_buf_get_skb() but forgot to
free it on one of the error paths.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Dave Jones<davej@fedoraproject.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| |/ /
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Callers of phy_ethtool_get_wol are supposed to provide a properly
cleared struct ethtool_wolinfo. Therefore, fix phy_suspend to clear
it before passing it to phy_ethtool_get_wol.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull networking fixes from David Miller:
"I know this is a bit more than you want to see, and I've told the
wireless folks under no uncertain terms that they must severely scale
back the extent of the fixes they are submitting this late in the
game.
Anyways:
1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
is the correct implementation, like it should. Instead it does
something like a NAPI poll operation. This leads to crashes.
From Neil Horman and Arnd Bergmann.
2) Segmentation of SKBs requires proper socket orphaning of the
fragments, otherwise we might access stale state released by the
release callbacks.
This is a 5 patch fix, but the initial patches are giving
variables and such significantly clearer names such that the
actual fix itself at the end looks trivial.
From Michael S. Tsirkin.
3) TCP control block release can deadlock if invoked from a timer on
an already "owned" socket. Fix from Eric Dumazet.
4) In the bridge multicast code, we must validate that the
destination address of general queries is the link local all-nodes
multicast address. From Linus Lüssing.
5) The x86 BPF JIT support for negative offsets puts the parameter
for the helper function call in the wrong register. Fix from
Alexei Starovoitov.
6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
r8169 driver is incorrect. Fix from Hayes Wang.
7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
if a packet is a GSO frame, but that's not the correct test. It
should use skb_is_gso(skb) instead. Fix from Wei Liu.
8) Negative msg->msg_namelen values should generate an error, from
Matthew Leach.
9) at86rf230 can deadlock because it takes the same lock from it's
ISR and it's hard_start_xmit method, without disabling interrupts
in the latter. Fix from Alexander Aring.
10) The FEC driver's restart doesn't perform operations in the correct
order, so promiscuous settings can get lost. Fix from Stefan
Wahren.
11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.
12) Reference count and memory leak fixes in TIPC from Ying Xue and
Erik Hugne.
13) Forced eviction in inet_frag_evictor() must strictly make sure all
frags are deleted, otherwise module unload (f.e. 6lowpan) can
crash. Fix from Florian Westphal.
14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
uses as a hash function), which breaks on PowerPC. From Anton
Blanchard.
The main gist of the issue is that csum_partial() is defined only
as a value that, once folded (f.e. via csum_fold()) produces a
correct 16-bit checksum. It is legitimate, therefore, for
csum_partial() to produce two different 32-bit values over the
same data if their respective alignments are different.
15) Fix endiannes bug in MAC address handling of ibmveth driver, also
from Anton Blanchard.
16) Error checks for ipv6 exthdrs offload registration are reversed,
from Anton Nayshtut.
17) Externally triggered ipv6 addrconf routes should count against the
garbage collection threshold. Fix from Sabrina Dubroca.
18) The PCI shutdown handler added to the bnx2 driver can wedge the
chip if it was not brought up earlier already, which in particular
causes the firmware to shut down the PHY. Fix from Michael Chan.
19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
currently coded it can and does trigger in legitimate situations.
From Eric Dumazet.
20) BNA driver fails to build on ARM because of a too large udelay()
call, fix from Ben Hutchings.
21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
from Eric Dumazet.
22) The vlan passthrough ops added in the previous release causes a
regression in source MAC address setting of outgoing headers in
some circumstances. Fix from Peter Boström"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
ipv6: Avoid unnecessary temporary addresses being generated
eth: fec: Fix lost promiscuous mode after reconnecting cable
bonding: set correct vlan id for alb xmit path
at86rf230: fix lockdep splats
net/mlx4_en: Deregister multicast vxlan steering rules when going down
vmxnet3: fix building without CONFIG_PCI_MSI
MAINTAINERS: add networking selftests to NETWORKING
net: socket: error on a negative msg_namelen
MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
packet: doc: Spelling s/than/that/
net/mlx4_core: Load the IB driver when the device supports IBoE
net/mlx4_en: Handle vxlan steering rules for mac address changes
net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
xen-netback: use skb_is_gso in xenvif_start_xmit
r8169: fix the incorrect tx descriptor version
tools/net/Makefile: Define PACKAGE to fix build problems
x86: bpf_jit: support negative offsets
bridge: multicast: enable snooping on general queries only
bridge: multicast: add sanity check for general query destination
tcp: tcp_release_cb() should release socket ownership
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The commit d3ab3ffd1d728d7ee77340e7e7e2c7cfe6a4013e
(bonding: use rlb_client_info->vlan_id instead of ->tag)
remove the rlb_client_info->tag, but occur some issues,
The vlan_get_tag() will return 0 for success and -EINVAL for
error, so the client_info->vlan_id always be set to 0 if the
vlan_get_tag return 0 for success, so the client_info would
never get a correct vlan id.
We should only set the vlan id to 0 when the vlan_get_tag return error.
Fixes: d3ab3ffd1d7 (bonding: use rlb_client_info->vlan_id instead of ->tag)
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fix a lockdep in the at86rf230 driver, otherwise we get:
[ 30.206517] =================================
[ 30.211078] [ INFO: inconsistent lock state ]
[ 30.215647] 3.14.0-20140108-1-00994-g32e9426 #163 Not tainted
[ 30.221660] ---------------------------------
[ 30.226222] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[ 30.232514] systemd-udevd/157 [HC1[1]:SC0[0]:HE0:SE1] takes:
[ 30.238439] (&(&lp->lock)->rlock){?.+...}, at: [<c03600f8>] at86rf230_isr+0x18/0x44
[ 30.246621] {HARDIRQ-ON-W} state was registered at:
[ 30.251728] [<c0061ce4>] __lock_acquire+0x7a4/0x18d8
[ 30.257135] [<c0063500>] lock_acquire+0x68/0x7c
[ 30.262071] [<c0588820>] _raw_spin_lock+0x28/0x38
[ 30.267203] [<c0361240>] at86rf230_xmit+0x1c/0x144
[ 30.272412] [<c057ba6c>] mac802154_xmit_worker+0x88/0x148
[ 30.278271] [<c0047844>] process_one_work+0x274/0x404
[ 30.283761] [<c00484c0>] worker_thread+0x228/0x374
[ 30.288971] [<c004cfb8>] kthread+0xd0/0xe4
[ 30.293455] [<c000dac8>] ret_from_fork+0x14/0x2c
[ 30.298493] irq event stamp: 8948
[ 30.301963] hardirqs last enabled at (8947): [<c00cb290>] __kmalloc+0xb4/0x110
[ 30.309636] hardirqs last disabled at (8948): [<c00115d4>] __irq_svc+0x34/0x5c
[ 30.317215] softirqs last enabled at (8452): [<c0037324>] __do_softirq+0x1dc/0x264
[ 30.325243] softirqs last disabled at (8439): [<c0037638>] irq_exit+0x80/0xf4
We use the lp->lock inside the isr of at86rf230, that's why we need the
irqsave spinlock calls.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since commit d25f06ea466e "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).
Fixes: b046ffe 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.
The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In 5bd076708 ("Xen-netback: Fix issue caused by using gso_type wrongly")
we use skb_is_gso to determine if we need an extra slot to accommodate
the SKB. There's similar error in interface.c. Change that to use
skb_is_gso as well.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Current netback uses gso_type to check whether the skb contains
gso offload, and this is wrong. Gso_size is the right one to
check gso existence, and gso_type is only used to check gso type.
Some skbs contains nonzero gso_type and zero gso_size, current
netback would treat these skbs as gso and create wrong response
for this. This also causes ssh failure to domu from other server.
V2: use skb_is_gso function as Paul Durrant suggested
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
udelay() does not work on some architectures for values above
2000, in particular on ARM:
ERROR: "__bad_udelay" [drivers/net/ethernet/brocade/bna/bna.ko] undefined!
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intende for the 3.14 stream...
For the mac80211 bits, Johannes says:
"Here I have a fix from Eliad for the minimal channel width calculation
in the mac80211 code which lead to monitor mode not working at all for
drivers using that. One of my fixes is for an issue noticed by Michal,
we clear an already cleared value but do it without locking, so just
remove that. The other is for a data leak - we leak two bytes of kernel
memory out over the air in QoS NULL frames because those don't get a
sequence number assigned in the TX path."
For the iwlwifi bits, Emmanuel says:
"One more fix and an update for device IDs.
There is a bugzilla reported for the fix which is mentioned in the commit message."
Along with those...
Amitkumar Karwar provides two mwifiex fixes, both correcting some
data transcription problems.
Ivaylo Dimitrov uses skb_trim in the wl1251 driver to avoid
HAVE_EFFICIENT_UNALIGNED_ACCESS problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |\|
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
While preparing association request, intersection of device's
VHT capability information and corresponding field advertised
by AP is used.
This patch fixes a couple errors while saving and copying vht_cap
and vht_oper fields from AP's beacon.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Cc: <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | |\
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Update of the HW IDs for the 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Since the statistics handler is asynchrous, it can very well
be that we will handle the statistics (hence the RSSI
fluctuation) when we already disassociated.
Don't WARN on this case.
This solves: https://bugzilla.redhat.com/show_bug.cgi?id=1071998
Cc: <stable@vger.kernel.org> [3.10+]
Fixes: 2b76ef13086f ("iwlwifi: mvm: implement reduced Tx power")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
the current code is directly setting skb->len, which is not correct and
brings problems with HAVE_EFFICIENT_UNALIGNED_ACCESS enabled in config
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4ba3b2d9a49ce9d9b0cd7be1840e15ed
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
ready
Currently, the PF call to pci_enable_sriov from the PF probe function
stalls for 10 seconds times the number of VFs probed on the host. This
happens because the way for such VFs to determine of the PF
initialization finished, is by attempting to issue reset on the
comm-channel and get timeout (after 10s).
The PF probe function is called from a kenernel workqueue, and therefore
during that time, rcu lock is being held and kernel's workqueue is
stalled. This blocks other processes that try to use the workqueue
or rcu lock. For example, interface renaming which is calling
rcu_synchronize is blocked, and timedout by systemd.
Changed mlx4_init_slave() to allow VF probed on the host to immediatly
detect that the PF is not ready, and return EPROBE_DEFER instantly.
Only when the PF finishes the initialization, allow such VFs to
access the comm channel.
This issue and fix are relevant only for probed VFs on the hypervisor,
there is no way to pass this information to a VM until comm channel is
ready, so in a VM, if PF is not ready, the first command will be timedout
after 10 seconds and return EPROBE_DEFER.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Fix a regression introduced by [1]. outbox was accessed instead of
outbox->buf. Typo was copy-pasted to [2] and [3].
[1] - cc1ade9 mlx4_core: Disable memory windows for virtual functions
[2] - 4de6580 mlx4_core: Add support for steerable IB UD QPs
[3] - 7ffdf72 net/mlx4_core: Add basic support for TCP/IP offloads under
tunneling
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We didn't correctly check cases where the value for lp_interval is not
within the legal range due to a missing table terminator.
This would let userspace trigger a kernel panic by specifying a value out
of range:
echo -1 > /sys/devices/virtual/net/bond0/bonding/lp_interval
Introduced by commit 4325b374f84 ("bonding: convert lp_interval to use
the new option API").
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
