summaryrefslogtreecommitdiffstats
path: root/drivers/net (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: phy: broadcom: hook up soft_reset for BCM54616SRobert Hancock2022-01-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which is a 1 Gbps copper module operating in SGMII mode with an internal BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the module would work properly on the initial insertion or boot of the device, but after the device was rebooted, the link would either only come up at 100 Mbps speeds or go up and down erratically. I found no meaningful changes in the PHY configuration registers between the working and non-working boots, but the status registers seemed to have a lot of error indications set on the SERDES side of the device on the non-working boot. I suspect the problem is that whatever happens on the SGMII link when the device is rebooted and the FPGA logic gets reloaded ends up putting the module's onboard PHY into a bad state. Since commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") the genphy_soft_reset call is not made automatically by the PHY core unless the callback is explicitly specified in the driver structure. For most of these Broadcom devices, there is probably a hardware reset that gets asserted to reset the PHY during boot, however for SFP modules (where the BCM54616S is commonly found) no such reset line exists, so if the board keeps the SFP cage powered up across a reboot, it will end up with no reset occurring during reboots. Hook up the genphy_soft_reset callback for BCM54616S to ensure that a PHY reset is performed before the device is initialized. This appears to fix the issue with erratic operation after a reboot with this SFP module. Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'net-5.17-rc1' of ↵Linus Torvalds2022-01-2036-208/+503
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from netfilter, bpf. Quite a handful of old regression fixes but most of those are pre-5.16. Current release - regressions: - fix memory leaks in the skb free deferral scheme if upper layer protocols are used, i.e. in-kernel TCP readers like TLS Current release - new code bugs: - nf_tables: fix NULL check typo in _clone() functions - change the default to y for Vertexcom vendor Kconfig - a couple of fixes to incorrect uses of ref tracking - two fixes for constifying netdev->dev_addr Previous releases - regressions: - bpf: - various verifier fixes mainly around register offset handling when passed to helper functions - fix mount source displayed for bpffs (none -> bpffs) - bonding: - fix extraction of ports for connection hash calculation - fix bond_xmit_broadcast return value when some devices are down - phy: marvell: add Marvell specific PHY loopback - sch_api: don't skip qdisc attach on ingress, prevent ref leak - htb: restore minimal packet size handling in rate control - sfp: fix high power modules without diagnostic monitoring - mscc: ocelot: - don't let phylink re-enable TX PAUSE on the NPI port - don't dereference NULL pointers with shared tc filters - smsc95xx: correct reset handling for LAN9514 - cpsw: avoid alignment faults by taking NET_IP_ALIGN into account - phy: micrel: use kszphy_suspend/_resume for irq aware devices, avoid races with the interrupt Previous releases - always broken: - xdp: check prog type before updating BPF link - smc: resolve various races around abnormal connection termination - sit: allow encapsulated IPv6 traffic to be delivered locally - axienet: fix init/reset handling, add missing barriers, read the right status words, stop queues correctly - add missing dev_put() in sock_timestamping_bind_phc() Misc: - ipv4: prevent accidentally passing RTO_ONLINK to ip_route_output_key_hash() by sanitizing flags - ipv4: avoid quadratic behavior in netns dismantle - stmmac: dwmac-oxnas: add support for OX810SE - fsl: xgmac_mdio: add workaround for erratum A-009885" * tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits) ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys ipv4: avoid quadratic behavior in netns dismantle net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses dt-bindings: net: Document fsl,erratum-a009885 net/fsl: xgmac_mdio: Add workaround for erratum A-009885 net: mscc: ocelot: fix using match before it is set net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind() net: axienet: increase default TX ring size to 128 net: axienet: fix for TX busy handling net: axienet: fix number of TX ring slots for available check net: axienet: Fix TX ring slot available check net: axienet: limit minimum TX ring size net: axienet: add missing memory barriers net: axienet: reset core on initialization prior to MDIO access net: axienet: Wait for PhyRstCmplt after core reset net: axienet: increase reset timeout bpf, selftests: Add ringbuf memory type confusion test ...
| * net/fsl: xgmac_mdio: Fix incorrect iounmap when removing moduleTobias Waldekranz2022-01-191-1/+2
| | | | | | | | | | | | | | | | | | | | | | As reported by sparse: In the remove path, the driver would attempt to unmap its own priv pointer - instead of the io memory that it mapped in probe. Fixes: 9f35a7342cff ("net/fsl: introduce Freescale 10G MDIO driver") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net/fsl: xgmac_mdio: Add workaround for erratum A-009885Tobias Waldekranz2022-01-191-6/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Once an MDIO read transaction is initiated, we must read back the data register within 16 MDC cycles after the transaction completes. Outside of this window, reads may return corrupt data. Therefore, disable local interrupts in the critical section, to maximize the probability that we can satisfy this requirement. Fixes: d55ad2967d89 ("powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: mscc: ocelot: fix using match before it is setTom Rix2022-01-191-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clang static analysis reports this issue ocelot_flower.c:563:8: warning: 1st function call argument is an uninitialized value !is_zero_ether_addr(match.mask->dst)) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The variable match is used before it is set. So move the block. Fixes: 75944fda1dfe ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devicesClaudiu Beznea2022-01-191-18/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On a setup with KSZ9131 and MACB drivers it happens on suspend path, from time to time, that the PHY interrupt arrives after PHY and MACB were suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this case the phy_read() at the beginning of kszphy_handle_interrupt() will fail (as MACB driver is suspended at this time) leading to phy_error() being called and a stack trace being displayed on console. To solve this .suspend/.resume functions for all KSZ devices implementing .handle_interrupt were replaced with kszphy_suspend()/kszphy_resume() which disable/enable interrupt before/after calling genphy_suspend()/genphy_resume(). The fix has been adapted for all KSZ devices which implements .handle_interrupt but it has been tested only on KSZ9131. Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into accountArd Biesheuvel2022-01-193-7/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Both versions of the CPSW driver declare a CPSW_HEADROOM_NA macro that takes NET_IP_ALIGN into account, but fail to use it appropriately when storing incoming packets in memory. This results in the IPv4 source and destination addresses to appear misaligned in memory, which causes aligment faults that need to be fixed up in software. So let's switch from CPSW_HEADROOM to CPSW_HEADROOM_NA where needed. This gets rid of any alignment faults on the RX path on a Beaglebone White. Fixes: 9ed4050c0d75 ("net: ethernet: ti: cpsw: add XDP support") Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: increase default TX ring size to 128Robert Hancock2022-01-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | With previous changes to make the driver handle the TX ring size more correctly, the default TX ring size of 64 appears to significantly bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP. Increasing this to 128 seems to bring performance up to near line rate and shouldn't cause excess bufferbloat (this driver doesn't yet support modern byte-based queue management). Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: fix for TX busy handlingRobert Hancock2022-01-191-39/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Network driver documentation indicates we should be avoiding returning NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires the packets to be requeued. Instead the queue should be stopped after a packet is added to the TX ring when there may not be enough room for an additional one. Also, when TX ring entries are completed, we should only wake the queue if we know there is room for another full maximally fragmented packet. Print a warning if there is insufficient space at the start of start_xmit, since this should no longer happen. Combined with increasing the default TX ring size (in a subsequent patch), this appears to recover the TX performance lost by previous changes to actually manage the TX ring state properly. Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: fix number of TX ring slots for available checkRobert Hancock2022-01-191-2/+2
| | | | | | | | | | | | | | | | | | | | The check for the number of available TX ring slots was off by 1 since a slot is required for the skb header as well as each fragment. This could result in overwriting a TX ring slot that was still in use. Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: Fix TX ring slot available checkRobert Hancock2022-01-191-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The check for whether a TX ring slot was available was incorrect, since a slot which had been loaded with transmit data but the device had not started transmitting would be treated as available, potentially causing non-transmitted slots to be overwritten. The control field in the descriptor should be checked, rather than the status field (which may only be updated when the device completes the entry). Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: limit minimum TX ring sizeRobert Hancock2022-01-191-1/+3
| | | | | | | | | | | | | | | | | | | | | | The driver will not work properly if the TX ring size is set to below MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally fragmented packet in the TX ring. Limit setting the ring size to below this value. Fixes: 8b09ca823ffb4 ("net: axienet: Make RX/TX ring sizes configurable") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: add missing memory barriersRobert Hancock2022-01-191-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver was missing some required memory barriers: Use dma_rmb to ensure we see all updates to the descriptor after we see that an entry has been completed. Use wmb and rmb to avoid stale descriptor status between the TX path and TX complete IRQ path. Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: reset core on initialization prior to MDIO accessRobert Hancock2022-01-191-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In some cases where the Xilinx Ethernet core was used in 1000Base-X or SGMII modes, which use the internal PCS/PMA PHY, and the MGT transceiver clock source for the PCS was not running at the time the FPGA logic was loaded, the core would come up in a state where the PCS could not be found on the MDIO bus. To fix this, the Ethernet core (including the PCS) should be reset after enabling the clocks, prior to attempting to access the PCS using of_mdio_find_device. Fixes: 1a02556086fc (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode) Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: Wait for PhyRstCmplt after core resetRobert Hancock2022-01-191-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When resetting the device, wait for the PhyRstCmplt bit to be set in the interrupt status register before continuing initialization, to ensure that the core is actually ready. When using an external PHY, this also ensures we do not start trying to access the PHY while it is still in reset. The PHY reset is initiated by the core reset which is triggered just above, but remains asserted for 5ms after the core is reset according to the documentation. The MgtRdy bit could also be waited for, but unfortunately when using 7-series devices, the bit does not appear to work as documented (it seems to behave as some sort of link state indication and not just an indication the transceiver is ready) so it can't really be relied on for this purpose. Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: axienet: increase reset timeoutRobert Hancock2022-01-191-10/+9
| | | | | | | | | | | | | | | | | | | | | | | | The previous timeout of 1ms was too short to handle some cases where the core is reset just after the input clocks were started, which will be introduced in an upcoming patch. Increase the timeout to 50ms. Also simplify the reset timeout checking to use read_poll_timeout. Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: sfp: fix high power modules without diagnostic monitoringRussell King (Oracle)2022-01-171-4/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") unintetionally changed the semantics for high power modules without the digital diagnostics monitoring. We repeatedly attempt to read the power status from the non-existing 0xa2 address in a futile hope this failure is temporary: [ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408 [ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode [ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5 [ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5 [ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5 We previosuly assumed such modules were powered up in the correct mode, continuing without further configuration as long as the required power class was supported by the host. Restore this behaviour, while preserving the intent of subsequent patches to avoid the "Address Change Sequence not supported" warning if we are not going to be accessing the DDM address. Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules") Reported-by: 照山周一郎 <teruyama@springboard-inc.jp> Tested-by: 照山周一郎 <teruyama@springboard-inc.jp> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ocelot: Fix the call to switchdev_bridge_port_offloadHoratiu Vultur2022-01-171-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | In the blamed commit, the call to the function switchdev_bridge_port_offload was passing the wrong argument for atomic_nb. It was ocelot_netdevice_nb instead of ocelot_swtchdev_nb. This patch fixes this issue. Fixes: 4e51bf44a03af6 ("net: bridge: move the switchdev object replay helpers to "push" mode") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * bonding: Fix extraction of ports from the packet headersMoshe Tal2022-01-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wrong hash sends single stream to multiple output interfaces. The offset calculation was relative to skb->head, fix it to be relative to skb->data. Fixes: a815bde56b15 ("net, bonding: Refactor bond_xmit_hash for use with xdp_buff") Reviewed-by: Jussi Maki <joamaki@gmail.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Moshe Tal <moshet@nvidia.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: wwan: Fix MRU mismatch issue which may lead to data connection lostSlark Xiao2022-01-151-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In pci_generic.c there is a 'mru_default' in struct mhi_pci_dev_info. This value shall be used for whole mhi if it's given a value for a specific product. But in function mhi_net_rx_refill_work(), it's still using hard code value MHI_DEFAULT_MRU. 'mru_default' shall have higher priority than MHI_DEFAULT_MRU. And after checking, this change could help fix a data connection lost issue. Fixes: 5c2c85315948 ("bus: mhi: pci-generic: configurable network interface MRU") Signed-off-by: Shujun Wang <wsj20369@163.com> Signed-off-by: Slark Xiao <slark_xiao@163.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: marvell: add Marvell specific PHY loopbackMohammad Athari Bin Ismail2022-01-151-1/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Existing genphy_loopback() is not applicable for Marvell PHY. Besides configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control Register), it is also required to configure same bits in Page 2 Register 21 (MAC Specific Control Register 2) according to speed of the loopback is operating. Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps). FIXME: Based on trial and error test, it seem 1G need to have delay between soft reset and loopback enablement. Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ethernet: sun4i-emac: Fix an error handling path in emac_probe()Christophe JAILLET2022-01-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | A dma_request_chan() call is hidden in emac_configure_dma(). It must be released in the probe if an error occurs, as already done in the remove function. Add the corresponding dma_release_channel() call. Fixes: 47869e82c8b8 ("sun4i-emac.c: add dma support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ethernet: mtk_eth_soc: fix error checking in mtk_mac_config()Tom Rix2022-01-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clang static analysis reports this problem mtk_eth_soc.c:394:7: warning: Branch condition evaluates to a garbage value if (err) ^~~ err is not initialized and only conditionally set. So intitialize err. Fixes: 7e538372694b ("net: ethernet: mediatek: Re-add support SGMII") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: mscc: ocelot: don't dereference NULL pointers with shared tc filtersVladimir Oltean2022-01-151-1/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following command sequence: tc qdisc del dev swp0 clsact tc qdisc add dev swp0 ingress_block 1 clsact tc qdisc add dev swp1 ingress_block 1 clsact tc filter add block 1 flower action drop tc qdisc del dev swp0 clsact produces the following NPD: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014 pc : vcap_entry_set+0x14/0x70 lr : ocelot_vcap_filter_del+0x198/0x234 Call trace: vcap_entry_set+0x14/0x70 ocelot_vcap_filter_del+0x198/0x234 ocelot_cls_flower_destroy+0x94/0xe4 felix_cls_flower_del+0x70/0x84 dsa_slave_setup_tc_block_cb+0x13c/0x60c dsa_slave_setup_tc_block_cb_ig+0x20/0x30 tc_setup_cb_reoffload+0x44/0x120 fl_reoffload+0x280/0x320 tcf_block_playback_offloads+0x6c/0x184 tcf_block_unbind+0x80/0xe0 tcf_block_setup+0x174/0x214 tcf_block_offload_cmd.isra.0+0x100/0x13c tcf_block_offload_unbind+0x5c/0xa0 __tcf_block_put+0x54/0x174 tcf_block_put_ext+0x5c/0x74 clsact_destroy+0x40/0x60 qdisc_destroy+0x4c/0x150 qdisc_put+0x70/0x90 qdisc_graft+0x3f0/0x4c0 tc_get_qdisc+0x1cc/0x364 rtnetlink_rcv_msg+0x124/0x340 The reason is that the driver isn't prepared to receive two tc filters with the same cookie. It unconditionally creates a new struct ocelot_vcap_filter for each tc filter, and it adds all filters with the same identifier (cookie) to the ocelot_vcap_block. The problem is here, in ocelot_vcap_filter_del(): /* Gets index of the filter */ index = ocelot_vcap_block_get_filter_index(block, filter); if (index < 0) return index; /* Delete filter */ ocelot_vcap_block_remove_filter(ocelot, block, filter); /* Move up all the blocks over the deleted filter */ for (i = index; i < block->count; i++) { struct ocelot_vcap_filter *tmp; tmp = ocelot_vcap_block_find_filter_by_index(block, i); vcap_entry_set(ocelot, i, tmp); } what will happen is ocelot_vcap_block_get_filter_index() will return the index (@index) of the first filter found with that cookie. This is _not_ the index of _this_ filter, but the other one with the same cookie, because ocelot_vcap_filter_equal() gets fooled. Then later, ocelot_vcap_block_remove_filter() is coded to remove all filters that are ocelot_vcap_filter_equal() with the passed @filter. So unexpectedly, both filters get deleted from the list. Then ocelot_vcap_filter_del() will attempt to move all the other filters up, again finding them by index (@i). The block count is 2, @index was 0, so it will attempt to move up filter @i=0 and @i=1. It assigns tmp = ocelot_vcap_block_find_filter_by_index(block, i), which is now a NULL pointer because ocelot_vcap_block_remove_filter() has removed more than one filter. As far as I can see, this problem has been there since the introduction of tc offload support, however I cannot test beyond the blamed commit due to hardware availability. In any case, any fix cannot be backported that far, due to lots of changes to the code base. Therefore, let's go for the correct solution, which is to not call ocelot_vcap_filter_add() and ocelot_vcap_filter_del(), unless the filter is actually unique and not shared. For the shared filters, we should just modify the ingress port mask and call ocelot_vcap_filter_replace(), a function introduced by commit 95706be13b9f ("net: mscc: ocelot: create a function that replaces an existing VCAP filter"). This way, block->rules will only contain filters with unique cookies, by design. Fixes: 07d985eef073 ("net: dsa: felix: Wire up the ocelot cls_flower methods") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: stmmac: Fix "Unbalanced pm_runtime_enable!" warningKai-Heng Feng2022-01-141-1/+2
| | | | | | | | | | | | | | | | | | | | If the device is PCI based like intel-eth-pci, pm_runtime_enable() is already called by pci_pm_init(). So only pm_runtime_enable() when it's not already enabled. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * lib82596: Fix IRQ check in sni_82596_probeMiaoqian Lin2022-01-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | platform_get_irq() returns negative error number instead 0 on failure. And the doc of platform_get_irq() provides a usage example: int irq = platform_get_irq(pdev, 0); if (irq < 0) return irq; Fix the check of return value to catch errors correctly. Fixes: 115978859272 ("i825xx: Move the Intel 82586/82593/82596 based drivers") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: apple: bmac: Fix build since dev_addr constificationMichael Ellerman2022-01-141-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit adeef3e32146 ("net: constify netdev->dev_addr") the bmac driver no longer builds with the following errors (pmac32_defconfig): linux/drivers/net/ethernet/apple/bmac.c: In function ‘bmac_probe’: linux/drivers/net/ethernet/apple/bmac.c:1287:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’ 1287 | dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j]; | ^ Fix it by making the modifications to a local macaddr variable and then passing that to eth_hw_addr_set(). We don't use the existing addr variable because the bitrev8() would mutate it, but it is already used unreversed later in the function. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: apple: mace: Fix build since dev_addr constificationMichael Ellerman2022-01-141-5/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit adeef3e32146 ("net: constify netdev->dev_addr") the mace driver no longer builds with various errors (pmac32_defconfig): linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_probe’: linux/drivers/net/ethernet/apple/mace.c:170:20: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)j)’ 170 | dev->dev_addr[j] = rev ? bitrev8(addr[j]): addr[j]; | ^ linux/drivers/net/ethernet/apple/mace.c: In function ‘mace_reset’: linux/drivers/net/ethernet/apple/mace.c:349:32: warning: passing argument 2 of ‘__mace_set_address’ discards ‘const’ qualifier from pointer target type 349 | __mace_set_address(dev, dev->dev_addr); | ~~~^~~~~~~~~~ linux/drivers/net/ethernet/apple/mace.c:93:62: note: expected ‘void *’ but argument is of type ‘const unsigned char *’ 93 | static void __mace_set_address(struct net_device *dev, void *addr); | ~~~~~~^~~~ linux/drivers/net/ethernet/apple/mace.c: In function ‘__mace_set_address’: linux/drivers/net/ethernet/apple/mace.c:388:36: error: assignment of read-only location ‘*(dev->dev_addr + (sizetype)i)’ 388 | out_8(&mb->padr, dev->dev_addr[i] = p[i]); | ^ Fix it by making the modifications to a local macaddr variable and then passing that to eth_hw_addr_set(), as well as adding some missing const qualifiers. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: usb: Correct reset handling of smsc95xxMarkus Reichl2022-01-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On boards with LAN9514 and no preconfigured MAC address we don't get an ip address from DHCP after commit a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx") anymore. Adding an explicit reset before starting the phy fixes the issue. [1] https://lore.kernel.org/netdev/199eebbd6b97f52b9119c9fa4fd8504f8a34de18.camel@collabora.com/ From: Gabriel Hojda <ghojda@yo2urs.ro> Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx") Signed-off-by: Gabriel Hojda <ghojda@yo2urs.ro> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * bcmgenet: add WOL IRQ checkSergey Shtylyov2022-01-141-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | The driver neglects to check the result of platform_get_irq_optional()'s call and blithely passes the negative error codes to devm_request_irq() (which takes *unsigned* IRQ #), causing it to fail with -EINVAL. Stop calling devm_request_irq() with the invalid IRQ #s. Fixes: 8562056f267d ("net: bcmgenet: request Wake-on-LAN interrupt") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: qmi_wwan: Add Hucom Wireless HM-211S/KKyoungkyu Park2022-01-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Hucom Wireless HM-211S/K is an LTE module based on Qualcomm MDM9207. This module supports LTE Band 1, 3, 5, 7, 8 and WCDMA Band 1. Manual testing showed that only interface number two replies to QMI messages. T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22de ProdID=9051 Rev= 3.18 S: Manufacturer=Android S: Product=Android S: SerialNumber=0123456789ABCDEF C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space> Acked-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/Yd+nxAA6KorDpQFv@choryu-tfx5470h Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: mscc: ocelot: don't let phylink re-enable TX PAUSE on the NPI portVladimir Oltean2022-01-131-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit b39648079db4 ("net: mscc: ocelot: disable flow control on NPI interface"), flow control should be disabled on the DSA CPU port when used in NPI mode. However, the commit blamed in the Fixes: tag below broke this, because it allowed felix_phylink_mac_link_up() to overwrite SYS_PAUSE_CFG_PAUSE_ENA for the DSA CPU port. This issue became noticeable since the device tree update from commit 8fcea7be5736 ("arm64: dts: ls1028a: mark internal links between Felix and ENETC as capable of flow control"). The solution is to check whether this is the currently configured NPI port from ocelot_phylink_mac_link_up(), and to not modify the statically disabled PAUSE frame transmission if it is. When the port is configured for lossless mode as opposed to tail drop mode, but the link partner (DSA master) doesn't observe the transmitted PAUSE frames, the switch termination throughput is much worse, as can be seen below. Before: root@debian:~# iperf3 -c 192.168.100.2 Connecting to host 192.168.100.2, port 5201 [ 5] local 192.168.100.1 port 37504 connected to 192.168.100.2 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 28.4 MBytes 238 Mbits/sec 357 22.6 KBytes [ 5] 1.00-2.00 sec 33.6 MBytes 282 Mbits/sec 426 19.8 KBytes [ 5] 2.00-3.00 sec 34.0 MBytes 285 Mbits/sec 343 21.2 KBytes [ 5] 3.00-4.00 sec 32.9 MBytes 276 Mbits/sec 354 22.6 KBytes [ 5] 4.00-5.00 sec 32.3 MBytes 271 Mbits/sec 297 18.4 KBytes ^C[ 5] 5.00-5.06 sec 2.05 MBytes 270 Mbits/sec 45 19.8 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-5.06 sec 163 MBytes 271 Mbits/sec 1822 sender [ 5] 0.00-5.06 sec 0.00 Bytes 0.00 bits/sec receiver After: root@debian:~# iperf3 -c 192.168.100.2 Connecting to host 192.168.100.2, port 5201 [ 5] local 192.168.100.1 port 49470 connected to 192.168.100.2 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 112 MBytes 941 Mbits/sec 259 143 KBytes [ 5] 1.00-2.00 sec 110 MBytes 920 Mbits/sec 329 144 KBytes [ 5] 2.00-3.00 sec 112 MBytes 936 Mbits/sec 255 144 KBytes [ 5] 3.00-4.00 sec 110 MBytes 927 Mbits/sec 355 105 KBytes [ 5] 4.00-5.00 sec 110 MBytes 926 Mbits/sec 350 156 KBytes [ 5] 5.00-6.00 sec 110 MBytes 925 Mbits/sec 305 148 KBytes [ 5] 6.00-7.00 sec 110 MBytes 924 Mbits/sec 320 143 KBytes [ 5] 7.00-8.00 sec 110 MBytes 925 Mbits/sec 273 97.6 KBytes [ 5] 8.00-9.00 sec 109 MBytes 913 Mbits/sec 299 141 KBytes [ 5] 9.00-10.00 sec 110 MBytes 922 Mbits/sec 287 146 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 1.08 GBytes 926 Mbits/sec 3032 sender [ 5] 0.00-10.00 sec 1.08 GBytes 925 Mbits/sec receiver Fixes: de274be32cb2 ("net: dsa: felix: set TX flow control according to the phylink_mac_link_up resolution") Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: qmi_wwan: add ZTE MF286D modem 19d2:1485Pawel Dembicki2022-01-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modem from ZTE MF286D is an Qualcomm MDM9250 based 3G/4G modem. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0 D: Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=19d2 ProdID=1485 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=MF286DZTED000000 C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=896mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00 I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: marvell: prestera: Fix deinit sequence for routerYevhen Orlov2022-01-124-2/+10
| | | | | | | | | | | | | | | | | | | | * Add missed call prestera_router_fini in prestera_switch_fini * Add prestera_router_hw_fini, which verify lists are empty Fixes: 69204174cc5c ("net: marvell: prestera: Add prestera router infra") Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu> Link: https://lore.kernel.org/r/20220111011129.5457-1-yevhen.orlov@plvision.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: marvell: prestera: Refactor router functionsYevhen Orlov2022-01-123-12/+14
| | | | | | | | | | | | | | | | | | | | * Reverse xmas tree variables order * User friendly messages on error paths * Refactor __prestera_inetaddr_event to use early return Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu> Link: https://lore.kernel.org/r/20220111011051.4941-1-yevhen.orlov@plvision.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: marvell: prestera: Refactor get/put VR functionsYevhen Orlov2022-01-122-17/+17
| | | | | | | | | | | | | | | | | | | | | | | | * Use refcount, instead of uint * Increment/decrement recount inside get/put * Fix error path in __prestera_vr_create. Remove unnecessary kfree. * Make __prestera_vr_destroy symmetric to "create" Fixes: bca5859bc6c6 ("net: marvell: prestera: add hardware router objects accounting") Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu> Link: https://lore.kernel.org/r/20220111011014.4418-1-yevhen.orlov@plvision.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: marvell: prestera: Cleanup router structYevhen Orlov2022-01-121-1/+0
| | | | | | | | | | | | | | | | | | | | Field "aborted" was added in 69204174cc5c ("net: marvell: prestera: Add prestera router infra"). It will not be used. So remove. Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu> Link: https://lore.kernel.org/r/20220111010826.3779-1-yevhen.orlov@plvision.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: stmmac: dwmac-oxnas: Add support for OX810SENeil Armstrong2022-01-121-22/+79
| | | | | | | | | | | | | | | | Add support for OX810SE dwmac glue setup, which is a simplified version of the OX820 introduced later with more control on the PHY interface. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: bonding: fix bond_xmit_broadcast return value error bugJie Wang2022-01-121-8/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In Linux bonding scenario, one packet is copied to several copies and sent by all slave device of bond0 in mode 3(broadcast mode). The mode 3 xmit function bond_xmit_broadcast() only ueses the last slave device's tx result as the final result. In this case, if the last slave device is down, then it always return NET_XMIT_DROP, even though the other slave devices xmit success. It may cause the tx statistics error, and cause the application (e.g. scp) consider the network is unreachable. For example, use the following command to configure server A. echo 3 > /sys/class/net/bond0/bonding/mode ifconfig bond0 up ifenslave bond0 eth0 eth1 ifconfig bond0 192.168.1.125 ifconfig eth0 up ifconfig eth1 down The slave device eth0 and eth1 are connected to server B(192.168.1.107). Run the ping 192.168.1.107 -c 3 -i 0.2 command, the following information is displayed. PING 192.168.1.107 (192.168.1.107) 56(84) bytes of data. 64 bytes from 192.168.1.107: icmp_seq=1 ttl=64 time=0.077 ms 64 bytes from 192.168.1.107: icmp_seq=2 ttl=64 time=0.056 ms 64 bytes from 192.168.1.107: icmp_seq=3 ttl=64 time=0.051 ms 192.168.1.107 ping statistics 0 packets transmitted, 3 received Actually, the slave device eth0 of the bond successfully sends three ICMP packets, but the result shows that 0 packets are transmitted. Also if we use scp command to get remote files, the command end with the following printings. ssh_exchange_identification: read: Connection timed out So this patch modifies the bond_xmit_broadcast to return NET_XMIT_SUCCESS if one slave device in the bond sends packets successfully. If all slave devices send packets fail, the discarded packets stats is increased. The skb is released when there is no slave device in the bond or the last slave device is down. Fixes: ae46f184bc1f ("bonding: propagate transmit status") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ipa: prevent concurrent replenishAlex Elder2022-01-122-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | We have seen cases where an endpoint RX completion interrupt arrives while replenishing for the endpoint is underway. This causes another instance of replenishing to begin as part of completing the receive transaction. If this occurs it can lead to transaction corruption. Use a new flag to ensure only one replenish instance for an endpoint executes at a time. Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ipa: use a bitmap for endpoint replenish_enabledAlex Elder2022-01-122-6/+17
| | | | | | | | | | | | | | | | | | | | Define a new replenish_flags bitmap to contain Boolean flags associated with an endpoint's replenishing state. Replace the replenish_enabled field with a flag in that bitmap. This is to prepare for the next patch, which adds another flag. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ipa: fix atomic update in ipa_endpoint_replenish()Alex Elder2022-01-121-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In ipa_endpoint_replenish(), if an error occurs when attempting to replenish a receive buffer, we just quit and try again later. In that case we increment the backlog count to reflect that the attempt was unsuccessful. Then, if the add_one flag was true we increment the backlog again. This second increment is not included in the backlog local variable though, and its value determines whether delayed work should be scheduled. This is a bug. Fix this by determining whether 1 or 2 should be added to the backlog before adding it in a atomic_add_return() call. Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Fixes: 84f9bd12d46db ("soc: qcom: ipa: IPA endpoints") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: at803x: make array offsets staticColin Ian King2022-01-121-1/+1
| | | | | | | | | | | | | | | | | | | | Don't populate the read-only const array offsets on the stack but instead make it static. Also makes the object code a little smaller. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220109231716.59012-1-colin.i.king@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * mlx5: Don't accidentally set RTO_ONLINK before mlx5e_route_lookup_ipv4_get()Guillaume Nault2022-01-121-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Mask the ECN bits before calling mlx5e_route_lookup_ipv4_get(). The tunnel key might have the last ECN bit set. This interferes with the route lookup process as ip_route_output_key_hash() interpretes this bit specially (to restrict the route scope). Found by code inspection, compile tested only. Fixes: c7b9038d8af6 ("net/mlx5e: TC preparation refactoring for routing update event") Fixes: 9a941117fb76 ("net/mlx5e: Maximize ip tunnel key usage on the TC offloading path") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * libcxgb: Don't accidentally set RTO_ONLINK in cxgb_find_route()Guillaume Nault2022-01-121-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Mask the ECN bits before calling ip_route_output_ports(). The tos variable might be passed directly from an IPv4 header, so it may have the last ECN bit set. This interferes with the route lookup process as ip_route_output_key_hash() interpretes this bit specially (to restrict the route scope). Found by code inspection, compile tested only. Fixes: 804c2f3e36ef ("libcxgb,iw_cxgb4,cxgbit: add cxgb_find_route()") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ethernet: sun4i-emac: replace magic number with macroConley Lee2022-01-122-13/+35
| | | | | | | | | | | | | | | | | | | | This patch remove magic numbers in sun4i-emac.c and replace with macros defined in sun4i-emac.h Signed-off-by: Conley Lee <conleylee@foxmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Link: https://lore.kernel.org/r/tencent_71466C2135CD1780B19D7844BE3F167C940A@qq.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * Revert "net: vertexcom: default to disabled on kbuild"Saeed Mahameed2022-01-111-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 6bf950a8ff72920340dfdec93c18bd3f5f35de6a. To align with other vendors, NET_VENDOR configs are supposed to be ON by default, while their drivers should default to OFF. Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20220110205246.66298-1-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | Merge branch 'akpm' (patches from Andrew)Linus Torvalds2022-01-201-0/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Merge more updates from Andrew Morton: "55 patches. Subsystems affected by this patch series: percpu, procfs, sysctl, misc, core-kernel, get_maintainer, lib, checkpatch, binfmt, nilfs2, hfs, fat, adfs, panic, delayacct, kconfig, kcov, and ubsan" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (55 commits) lib: remove redundant assignment to variable ret ubsan: remove CONFIG_UBSAN_OBJECT_SIZE kcov: fix generic Kconfig dependencies if ARCH_WANTS_NO_INSTR lib/Kconfig.debug: make TEST_KMOD depend on PAGE_SIZE_LESS_THAN_256KB btrfs: use generic Kconfig option for 256kB page size limit arch/Kconfig: split PAGE_SIZE_LESS_THAN_256KB from PAGE_SIZE_LESS_THAN_64KB configs: introduce debug.config for CI-like setup delayacct: track delays from memory compact Documentation/accounting/delay-accounting.rst: add thrashing page cache and direct compact delayacct: cleanup flags in struct task_delay_info and functions use it delayacct: fix incomplete disable operation when switch enable to disable delayacct: support swapin delay accounting for swapping without blkio panic: remove oops_id panic: use error_report_end tracepoint on warnings fs/adfs: remove unneeded variable make code cleaner FAT: use io_schedule_timeout() instead of congestion_wait() hfsplus: use struct_group_attr() for memcpy() region nilfs2: remove redundant pointer sbufs fs/binfmt_elf: use PT_LOAD p_align values for static PIE const_structs.checkpatch: add frequently used ops structs ...
| * | include/linux/unaligned: replace kernel.h with the necessary inclusionsAndy Shevchenko2022-01-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When kernel.h is used in the headers it adds a lot into dependency hell, especially when there are circular dependencies are involved. Replace kernel.h inclusion with the list of what is really being used. The rest of the changes are induced by the above and may not be split. Link: https://lkml.kernel.org/r/20211209123823.20425-1-andriy.shevchenko@linux.intel.com Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> [brcmfmac] Acked-by: Kalle Valo <kvalo@kernel.org> Cc: Arend van Spriel <aspriel@gmail.com> Cc: Franky Lin <franky.lin@broadcom.com> Cc: Hante Meuleman <hante.meuleman@broadcom.com> Cc: Chi-hsien Lin <chi-hsien.lin@infineon.com> Cc: Wright Feng <wright.feng@infineon.com> Cc: Chung-hsien Hsu <chung-hsien.hsu@infineon.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | lib/crypto: blake2s: move hmac construction into wireguardJason A. Donenfeld2022-01-181-6/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Basically nobody should use blake2s in an HMAC construction; it already has a keyed variant. But unfortunately for historical reasons, Noise, used by WireGuard, uses HKDF quite strictly, which means we have to use this. Because this really shouldn't be used by others, this commit moves it into wireguard's noise.c locally, so that kernels that aren't using WireGuard don't get this superfluous code baked in. On m68k systems, this shaves off ~314 bytes. Cc: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 00:42:14 +0100