summaryrefslogtreecommitdiffstats
path: root/drivers/net (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: macb: Fix race between HW and driverSoren Brinkmann2014-05-051-10/+0
| | | | | | | | | | | | | | | Under "heavy" RX load, the driver cannot handle the descriptors fast enough. In detail, when a descriptor is consumed, its used flag is cleared and once the RX budget is consumed all descriptors with a cleared used flag are prepared to receive more data. Under load though, the HW may constantly receive more data and use those descriptors with a cleared used flag before they are actually prepared for next usage. The head and tail pointers into the RX-ring should always be valid and we can omit clearing and checking of the used flag. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: macb: Remove 'unlikely' optimizationSoren Brinkmann2014-05-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Coverage data suggests that the unlikely case of receiving data while the receive handler is running may not be that unlikely. Coverage data after running iperf for a while: 91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget); 91320: 892: if (work_done < budget) { 2362: 893: napi_complete(napi); -: 894: -: 895: /* Packets received while interrupts were disabled */ 4724: 896: status = macb_readl(bp, RSR); 2362: 897: if (unlikely(status)) { 762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE) 762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP)); -: 900: napi_reschedule(napi); -: 901: } else { 1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS); -: 903: } -: 904: } Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: macb: Re-enable RX interrupt only when RX is doneSoren Brinkmann2014-05-051-7/+6
| | | | | | | | | When data is received during the driver processing received data the NAPI is re-scheduled. In that case the RX interrupt should not be re-enabled. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: macb: Clear interrupt flagsSoren Brinkmann2014-05-051-0/+10
| | | | | | | | | A few interrupt flags were not cleared in the ISR, resulting in a sytem trapped in the ISR in cases one of those interrupts occurred. Clear all flags to avoid such situations. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: macb: Pass same size to DMA_UNMAP as used for DMA_MAPSoren Brinkmann2014-05-051-1/+1
| | | | | | | | | | Just as commit "net: macb: DMA-unmap full rx-buffer" (48330e08fa168395b9fd9f369f06cca1df204361), pass the size that was used for mapping the memory also to the unmap routine to avoid warnings from the DMA_API. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2014-05-053-29/+46
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to e1000e only. David provides four fixes for e1000e, first is a workaround for a hardware erratum on 82579 devices which experienced packet loss in gigabit and 100 speeds when interconnect between the PHY and MAC is exiting K1 power saving state. Second expands the scope of a workaround to include i217 and i218 parts as well to address over aggressive transmit behavior when connecting at 10Mbs half-duplex. Next is to resolve a reported link flap issue on 82579 parts which was root caused as an interoperability problem between 82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake mechanism. Lastly, restricts the workaround of putting the PHY into MDIO slow mode to access the PHY id to relevant parts since this issue has been fixed on the newer hardware. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * e1000e: Restrict MDIO Slow Mode workaround to relevant partsDavid Ertman2014-05-051-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It has been determined that the workaround of putting the PHY into MDIO slow mode to access the PHY id is not necessary with Lynx Point and newer parts. The issue that necessitated the workaround has been fixed on the newer hardware. We will maintains, as a last ditch attempt, the conversion to MDIO Slow Mode in the failure branch when attempting to access the PHY id so as to cover all contingencies. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Fix issue with link flap on 82579David Ertman2014-05-052-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several customers have reported a link flap issue on 82579. The symptoms are random and intermittent link losses when 82579 is connected to specific link partners. Issue has been root caused as interoperability problem between 82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake mechanism. To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M Low Power Idle. This solution will cause an increase of power in 100M EEE link. It will cost additional 28mW in this specific mode. Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Expand workaround for 10Mb HD throughput bugDavid Ertman2014-05-052-4/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance between two 82579 connected via 10Mbit hub", a workaround was put into place to address the overaggressive transmit behavior of 82579 parts when connecting at 10Mbs half-duplex. This same behavior is seen on i217 and i218 parts as well. This patch expands the original workaround to encompass these parts. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Workaround for dropped packets in Gig/100 speeds on 82579David Ertman2014-05-052-19/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a workaround for a HW erratum on 82579 devices. Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset specification Update June 2013. Problem: 82579 parts experience packet loss in Gig and 100 speeds when interconnect between PHY and MAC is exiting K1 power saving state. This was previously believed to only affect 1Gig speed, but has been observed at 100Mbs also. Workaround: Disable K1 for 82579 devices at Gig and 100 speeds. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | net/mlx4_core: Don't issue PCIe speed/width checks for VFsEyal Perry2014-05-051-1/+2
| | | | | | | | | | | | | | | | | | | | Carrying out PCI speed/width checks through pcie_get_minimum_link() on VFs yield wrong results, so remove them. Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth') Signed-off-by: Eyal Perry <eyalpe@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Load the Eth driver firstOr Gerlitz2014-05-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | When running in SRIOV mode, VM that is assigned with a non-provisioned Ethernet VFs get themselves a random mac when the Eth driver starts. In this case, if the IB driver startup code that deals with RoCE runs first, it will use a zero mac as the source mac for the Para-Virtual CM MADs which is buggy. To handle that, we change the order of loading. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Fix slave id computation for single port VFMatan Barak2014-05-051-15/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | The code that deals with computing the slave id based on a given GID gave wrong results when the number of single port VFs wasn't the same for port 1 vs. port 2 and the relevant VF is single ported on port 2. As a result, incoming CM MADs were dispatched to the wrong VF. Fixed that and added documentation to clarify the computation steps. Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/mlx4_core: Adjust port number in qp_attach wrapper when detachingJack Morgenstein2014-05-051-0/+23
| | | | | | | | | | | | | | | | | | | | | | When using single ported VFs and the VF is using port 2, we need to adjust the port accordingly (change it from 1 to 2). Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: cdc_ncm: fix buffer overflowBjørn Mork2014-05-051-1/+1
|/ | | | | | | | | | | | | | | | | | | Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs") changed the padding logic for devices with the ZLP flag set. This meant that frames of any size will be sent without additional padding, except for the single byte added if the size is a multiple of the USB packet size. But if the unpadded size is identical to the maximum frame size, and the maximum size is a multiplum of the USB packet size, then this one-byte padding will overflow the buffer. Prevent padding if already at maximum frame size, letting usbnet transmit a ZLP instead in this case. Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs") Reported by: Yu-an Shih <yshih@nvidia.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* Altera TSE: ALTERA_TSE should depend on HAS_DMAGeert Uytterhoeven2014-05-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | If NO_DMA=y: drivers/built-in.o: In function `altera_tse_probe': altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask' altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported' altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported' drivers/built-in.o: In function `sgdma_async_read': altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `sgdma_uninitialize': (.text+0x25f678): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `sgdma_uninitialize': (.text+0x25f696): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `sgdma_initialize': (.text+0x25f6f0): undefined reference to `dma_map_single' drivers/built-in.o: In function `sgdma_initialize': (.text+0x25f702): undefined reference to `dma_mapping_error' drivers/built-in.o: In function `sgdma_tx_buffer': (.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu' drivers/built-in.o: In function `sgdma_rx_status': (.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu' make[3]: *** [vmlinux] Error 1 Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'for-davem' of ↵David S. Miller2014-05-0513-43/+41
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== pull request: wireless 2014-05-01 Please pull the following batch of fixes intended for the 3.15 stream! For the Bluetooth bits, Gustavo says: "Some fixes for 3.15. There is a revert for the intel driver, a new device id, and two important SSP fixes from Johan." On top of that... Ben Hutchings gives us a fix for an unbalanced irq enable in an rtl8192cu error path. Colin Ian King provides an rtlwifi fix for an uninitialized variable. Felix Fietkau brings a pair of ath9k fixes, one that corrects a hardware initialization value and another that removes an (unnecessary) flag that was being used in a way that led to a software tx queue hang in ath9k. Gertjan van Wingerde pushes a MAINTAINERS change to remove himself from the rt2x00 maintainer team. Hans de Goede fixes a brcmfmac firmware load hang. Larry Finger changes rtlwifi to use the correct queue for V0 traffic on rtl8192se. Rajkumar Manoharan corrects a race in ath9k driver initialization. Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing once on USB devices led to permanently disabling beaconing for those devices. Tim Harvey provides fixes for a pair of ath9k issues that can lead to soft lockups in that driver. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge branch 'master' of ↵John W. Linville2014-05-0113-43/+41
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
| | * rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()Ben Hutchings2014-04-301-1/+1
| | | | | | | | | | | | | | | | | | | | | Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * rtlwifi: rtl8192se: Fix regression due to commit 1bf4bbbLarry Finger2014-04-301-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beginning with kernel 3.13, this driver fails on some systems. The problem was bisected to: Commit 1bf4bbb4024dcdab5e57634dd8ae1072d42a53ac Author: Felix Fietkau <nbd@openwrt.org> Title: mac80211: send control port protocol frames to the VO queue There is noting wrong with the above commit. The regression occurs because V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to modify the rtl8192se routine that sets the correct transmit queue. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541 Reported-by: Alex Miller <almiller_1@yahoo.co.uk> Tested-by: Alex Miller <almiller_1@yahoo.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.13+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * ath9k: remove tid->paused flagFelix Fietkau2014-04-303-17/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are some corner cases where the driver could get stuck with a full tid queue that is paused, leading to a software tx queue hang. Since the tx queueing rework, pausing per-tid queues on aggregation session setup is no longer necessary. The driver will assign sequence numbers to buffered frames when a new session is established, in order to get the correct starting sequence number. mac80211 prevents new frames from entering the queue during setup. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * ath9k_hw: do not lower ANI setting below default on AR913xFelix Fietkau2014-04-301-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the amount of noise fluctuates strongly, low immunity settings can sometimes disrupt signal detection on AR913x chips. When that happens, no OFDM/CCK errors are reported anymore, and ANI tunes the radio to the lowest immunity settings. Usually rx/tx fails as well in that case. To fix this, keep noise immunity settings at or above ANI default level, which will keep radio parameters at or above INI values. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * brcmfmac: Fix brcmf_chip_ai_coredisable not applying reset bits to BCMA_IOCTLHans de Goede2014-04-251-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | brcmfmac has been broken on my cubietruck with a BCM43362: brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1 brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d since commit 53036261033: "brcmfmac: update core reset and disable routines". The problem is that since this commit brcmf_chip_ai_resetcore no longer sets BCMA_IOCTL itself before bringing the core out of reset, instead relying on brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable to always set BCMA_IOCTL even if the core is already in reset. This fixes brcmfmac hanging in firmware loading on my board. Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * ath9k: fix race in setting ATH_OP_INVALIDRajkumar Manoharan2014-04-253-9/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit "ath9k: move sc_flags to ath_common" moved setting ATH_OP_INVALID flag below ieee80211_register_hw. This is causing the flag never being cleared randomly as the drv_start is called prior to setting flag. Fix this by setting the flag prior to register_hw. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * ath9k: add a recv budgetTim Harvey2014-04-221-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement a recv budget so that in cases of high traffic we still allow other taskets to get processed. Without this, we can encounter a host of issues during high wireless traffic reception depending on system load including rcu stall's detected (ARM), soft lockups, failure to service critical tasks such as watchdog resets, and triggering of the tx stuck tasklet. The same thing was proposed previously by Ben: http://www.spinics.net/lists/linux-wireless/msg112891.html The only difference here is that I make sure only processed packets are counted in the budget by checking at the end of the rx loop. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * ath9k: fix possible hang on flushTim Harvey2014-04-221-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a flush is requested, make sure to clear the descriptor once we've processed it. This resolves a hang that will occur if all RX descriptors are full when a flush is requested. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * rtlwifi: rtl8188ee: initialize packet_beaconColin Ian King2014-04-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | static code analysis from cppcheck reports: [drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]: (error) Uninitialized variable: packet_beacon packet_beacon is not initialized and hence packet_beacon contains garbage from the stack, so set it to false. Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: Stable <stable@vger.kernel.org> [3.10+] Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * rt2x00: fix beaconing on USBStanislaw Gruszka2014-04-221-10/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | When disable beaconing we clear register with beacon and newer set it back, what make we stop send beacons infinitely. Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | net: mvmdio: Check for a valid interrupt instead of an errorEzequiel Garcia2014-05-021-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following commit: commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef Author: Rob Herring <robh@kernel.org> Date: Wed Apr 23 17:57:41 2014 -0500 of/irq: do irq resolution in platform_get_irq changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER, in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq() returns EINVAL, but we currently check only for ENXIO. Fix this by looking for a positive integer, which is the proper way of validating a virtual interrupt number. While at it, add a proper handling for the deferral probe case. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net phy: Check for aneg completion before setting state to PHY_RUNNINGBalakumaran Kannan2014-05-021-0/+11
|/ / | | | | | | | | | | | | | | | | | | | | phy_state_machine should check whether auto-negotiatin is completed before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If auto-negotiation is not completed phydev->state should be set to PHY_AN. Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | hyperv: Properly handle checksum offloadKY Srinivasan2014-04-301-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do checksum offload only if the client of the driver wants checksum to be offloaded. In V1 version of this patch, I addressed comments from Stephen Hemminger <stephen@networkplumber.org> and Eric Dumazet <eric.dumazet@gmail.com>. In this version of the patch I have addressed comments from David Miller. This patch fixes a bug that is exposed in gateway scenarios. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | gianfar: Avoid unnecessary reg accesses in adjust_link()Claudiu Manoil2014-04-301-110/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For phy devices that don't issue interrupts upon link state changes, phylib polls the link state resulting in repeated calls to adjust_link(), even if the link state didn't change. As a result, some mac registers are repeatedly read and written with the same values, which is not ok. To fix this, adjust_link() has been refactored to check first whether the link state has changed and to take action only if needed, updating mac registers and local state variables. The 'new_state' local flag, set if one of the link params changed (link, speed or duplex), has been rendered useless and removed by this refactoring. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Revert "macvlan : fix checksums error when we are in bridge mode"Vlad Yasevich2014-04-301-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 12a2856b604476c27d85a5f9a57ae1661fc46019. The commit above doesn't appear to be necessary any more as the checksums appear to be correctly computed/validated. Additionally the above commit breaks kvm configurations where one VM is using a device that support checksum offload (virtio) and the other VM does not. In this case, packets leaving virtio device will have CHECKSUM_PARTIAL set. The packets is forwarded to a macvtap that has offload features turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not update the checksum and thus a bad checksum is passed up to the guest. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mactap: Fix checksum errors for non-gso packets in bridge modeVlad Yasevich2014-04-301-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following is a problematic configuration: VM1: virtio-net device connected to macvtap0@eth0 VM2: e1000 device connect to macvtap1@eth0 The problem is is that virtio-net supports checksum offloading and thus sends the packets to the host with CHECKSUM_PARTIAL set. On the other hand, e1000 does not support any acceleration. For small TCP packets (and this includes the 3-way handshake), e1000 ends up receiving packets that only have a partial checksum set. This causes TCP to fail checksum validation and to drop packets. As a result tcp connections can not be established. Commit 3e4f8b787370978733ca6cae452720a4f0c296b8 macvtap: Perform GSO on forwarding path. fixes this issue for large packets wthat will end up undergoing GSO. This commit adds a check for the non-GSO case and attempts to compute the checksum for partially checksummed packets in the non-GSO case. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: sxgbe: Added set function for interrupt on completeByungho An2014-04-303-0/+11
| | | | | | | | | | | | | | | | This patch adds set_rx_int_on_com function for interrupt when dma is completed. Signed-off-by: Byungho An <bh74.an@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: sxgbe: Added rxqueue enable functionByungho An2014-04-304-0/+36
| | | | | | | | | | | | | | | | This patch adds rxqueue enable function according to number of rxqueue and adds rxqueue disable function for removing. Signed-off-by: Byungho An <bh74.an@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: sxgbe: sw reset moved to probe functionByungho An2014-04-302-13/+22
| | | | | | | | | | | | | | | | This patch moves sw reset to probe function because sw reset is needed early stage before open function. Signed-off-by: Byungho An <bh74.an@samsung.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | cxgb4: Decode PCIe Gen3 link speedRoland Dreier2014-04-301-0/+2
| | | | | | | | | | | | | | Add handling for " 8 GT/s" in print_port_info(). Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Altera TSE: Add missing include to silence sparse warningsTobias Klauser2014-04-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the following sparse warnings: drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static? drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static? Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Altera TSE: Fix DMA secriptor length initializationTobias Klauser2014-04-301-37/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sgdma_descrip is a function name as well as the name of a struct. In sgdma_initialize(), we should initialize the descriptor length field with the actual length of a descriptor not with the size of the function. In order to prevent such things from happening in the future, rename the function to sgdma_setup_descrip(). Found by sparse which yields the following warning: drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: bonding: Fix format string mismatch in bond_sysfs.cMasanari Iida2014-04-281-1/+1
| | | | | | | | | | | | | | Fix format string mismatch in bonding_show_min_links(). Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | slip: fix spinlock variantOliver Hartkopp2014-04-281-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a formerly missing locking was added to slip.c and slcan.c by Andre Naujoks. Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock variant") as the kernel lock debugging advised to use spin_lock_bh() instead of just using spin_lock(). This fix has to be applied to the same code section in slip.c for the same reason too. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add a number of Dell devicesBjørn Mork2014-04-281-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dan writes: "The Dell drivers use the same configuration for PIDs: 81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card 81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card 81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card 81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card 81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card These devices are all clearly Sierra devices, but are also definitely Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750. >From DellGobi5kSetup.exe from the Dell drivers: usbif0: serial/firmware loader? usbif2: nmea usbif3: modem/ppp usbif8: net/QMI" Reported-by: AceLan Kao <acelan.kao@canonical.com> Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add a number of CMOTech devicesBjørn Mork2014-04-281-0/+16
| | | | | | | | | | | | | | | | | | A number of older CMOTech modems are based on Qualcomm chips and exporting a QMI/wwan function. Reported-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add Alcatel L800MABjørn Mork2014-04-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | Device interface layout: 0: ff/ff/ff - serial 1: ff/00/00 - serial AT+PPP 2: ff/ff/ff - QMI/wwan 3: 08/06/50 - storage Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add Olivetti Olicard 500Bjørn Mork2014-04-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Device interface layout: 0: ff/ff/ff - serial 1: ff/ff/ff - serial AT+PPP 2: 08/06/50 - storage 3: ff/ff/ff - serial 4: ff/ff/ff - QMI/wwan Reported-by: Julio Araujo <julio.araujo@wllctel.com.br> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add Sierra Wireless MC7305/MC7355Bjørn Mork2014-04-281-0/+1
| | | | | | | | | | Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add Sierra Wireless MC73xxBjørn Mork2014-04-281-0/+3
| | | | | | | | | | Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: qmi_wwan: add Sierra Wireless EM7355Bjørn Mork2014-04-281-0/+1
| | | | | | | | | | Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* | arc_emac: add clock handlingHeiko Stübner2014-04-282-11/+37
| | | | | | | | | | | | | | | | | | | | This adds ability for the arc_emac to really handle its supplying clock. To get the needed clock-frequency either a real clock or the previous clock-frequency property must be provided. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Max Schwarz <max.schwarz@online.de> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 16:59:33 +0100