summaryrefslogtreecommitdiffstats
path: root/drivers/net (follow)
Commit message (Collapse)AuthorAgeFilesLines
* net: broadcom: remove select MII from brcmstb Ethernet driversJustin Chen2024-10-121-3/+0
| | | | | | | | | | The MII driver isn't used by brcmstb Ethernet drivers. Remove it from the BCMASP, GENET, and SYSTEMPORT drivers. Signed-off-by: Justin Chen <justin.chen@broadcom.com> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20241010191332.1074642-1-justin.chen@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: configure collision detection based on PLCA modeParthiban Veerasooran2024-10-121-3/+39
| | | | | | | | | | | | | | | As per LAN8650/1 Rev.B0/B1 AN1760 (Revision F (DS60001760G - June 2024)) and LAN8670/1/2 Rev.C1/C2 AN1699 (Revision E (DS60001699F - June 2024)), under normal operation, the device should be operated in PLCA mode. Disabling collision detection is recommended to allow the device to operate in noisy environments or when reflections and other inherent transmission line distortion cause poor signal quality. Collision detection must be re-enabled if the device is configured to operate in CSMA/CD mode. Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-8-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: add support for Microchip's LAN867X Rev.C2Parthiban Veerasooran2024-10-122-7/+19
| | | | | | | | | | | | Add support for LAN8670/1/2 Rev.C2 as per the latest configuration note AN1699 released (Revision E (DS60001699F - June 2024)) for Rev.C1 is also applicable for Rev.C2. Refer hardware revisions list in the latest AN1699 Revision E (DS60001699F - June 2024). https://www.microchip.com/en-us/application-notes/an1699 Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-7-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: add support for Microchip's LAN867X Rev.C1Parthiban Veerasooran2024-10-122-2/+66
| | | | | | | | | | Add support for LAN8670/1/2 Rev.C1 as per the latest configuration note AN1699 released (Revision E (DS60001699F - June 2024)). https://www.microchip.com/en-us/application-notes/an1699 Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-6-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: move LAN867X reset handling to a new functionParthiban Veerasooran2024-10-121-1/+12
| | | | | | | | | | Move LAN867X reset handling code to a new function called lan867x_check_reset_complete() which will be useful for the next patch which also uses the same code to handle the reset functionality. Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-5-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: add support for Microchip's LAN865X Rev.B1Parthiban Veerasooran2024-10-122-33/+33
| | | | | | | | | | | | Add support for LAN8650/1 Rev.B1. As per the latest configuration note AN1760 released (Revision F (DS60001760G - June 2024)) for Rev.B0 is also applicable for Rev.B1. Refer hardware revisions list in the latest AN1760 Revision F (DS60001760G - June 2024). https://www.microchip.com/en-us/application-notes/an1760 Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-4-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: update new initial settings for LAN865X Rev.B0Parthiban Veerasooran2024-10-121-36/+84
| | | | | | | | | | | Update the new/improved initial settings from the latest configuration application note AN1760 released for LAN8650/1 Rev.B0 Revision F (DS60001760G - June 2024). https://www.microchip.com/en-us/application-notes/an1760 Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-3-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: microchip_t1s: restructure cfg read/write functions argumentsParthiban Veerasooran2024-10-121-11/+16
| | | | | | | | | | | Restructure lan865x_write_cfg_params() and lan865x_read_cfg_params() functions arguments to more generic which will be useful for the next patch which updates the improved initial configuration for LAN8650/1 Rev.B0 published in the Configuration Note. Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20241010082205.221493-2-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* netdevsim: copy addresses for both in and out pathsHangbin Liu2024-10-121-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current code only copies the address for the in path, leaving the out path address set to 0. This patch corrects the issue by copying the addresses for both the in and out paths. Before this patch: # cat /sys/kernel/debug/netdevsim/netdevsim0/ports/0/ipsec SA count=2 tx=20 sa[0] tx ipaddr=0.0.0.0 sa[0] spi=0x00000100 proto=0x32 salt=0x0adecc3a crypt=1 sa[0] key=0x3167608a ca4f1397 43565909 941fa627 sa[1] rx ipaddr=192.168.0.1 sa[1] spi=0x00000101 proto=0x32 salt=0x0adecc3a crypt=1 sa[1] key=0x3167608a ca4f1397 43565909 941fa627 After this patch: = cat /sys/kernel/debug/netdevsim/netdevsim0/ports/0/ipsec SA count=2 tx=20 sa[0] tx ipaddr=192.168.0.2 sa[0] spi=0x00000100 proto=0x32 salt=0x0adecc3a crypt=1 sa[0] key=0x3167608a ca4f1397 43565909 941fa627 sa[1] rx ipaddr=192.168.0.1 sa[1] spi=0x00000101 proto=0x32 salt=0x0adecc3a crypt=1 sa[1] key=0x3167608a ca4f1397 43565909 941fa627 Fixes: 7699353da875 ("netdevsim: add ipsec offload testing") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20241010040027.21440-3-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* netdevsim: print human readable IP addressHangbin Liu2024-10-121-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, IPSec addresses are printed in hexadecimal format, which is not user-friendly. e.g. # cat /sys/kernel/debug/netdevsim/netdevsim0/ports/0/ipsec SA count=2 tx=20 sa[0] rx ipaddr=0x00000000 00000000 00000000 0100a8c0 sa[0] spi=0x00000101 proto=0x32 salt=0x0adecc3a crypt=1 sa[0] key=0x3167608a ca4f1397 43565909 941fa627 sa[1] tx ipaddr=0x00000000 00000000 00000000 00000000 sa[1] spi=0x00000100 proto=0x32 salt=0x0adecc3a crypt=1 sa[1] key=0x3167608a ca4f1397 43565909 941fa627 This patch updates the code to print the IPSec address in a human-readable format for easier debug. e.g. # cat /sys/kernel/debug/netdevsim/netdevsim0/ports/0/ipsec SA count=4 tx=40 sa[0] tx ipaddr=0.0.0.0 sa[0] spi=0x00000100 proto=0x32 salt=0x0adecc3a crypt=1 sa[0] key=0x3167608a ca4f1397 43565909 941fa627 sa[1] rx ipaddr=192.168.0.1 sa[1] spi=0x00000101 proto=0x32 salt=0x0adecc3a crypt=1 sa[1] key=0x3167608a ca4f1397 43565909 941fa627 sa[2] tx ipaddr=:: sa[2] spi=0x00000100 proto=0x32 salt=0x0adecc3a crypt=1 sa[2] key=0x3167608a ca4f1397 43565909 941fa627 sa[3] rx ipaddr=2000::1 sa[3] spi=0x00000101 proto=0x32 salt=0x0adecc3a crypt=1 sa[3] key=0x3167608a ca4f1397 43565909 941fa627 Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20241010040027.21440-2-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: dsa: mv88e6xxx: Fix uninitialised err valueAryan Srivastava2024-10-121-1/+1
| | | | | | | | | | | The err value in mv88e6xxx_region_atu_snapshot is now potentially uninitialised on return. Initialise err as 0. Fixes: ada5c3229b32 ("net: dsa: mv88e6xxx: Add FID map cache") Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: emaclite: Adopt clock supportAbin Joseph2024-10-121-0/+7
| | | | | | | | | | | | Adapt to use the clock framework. Add s_axi_aclk clock from the processor bus clock domain and make clk optional to keep DTB backward compatibility. Signed-off-by: Abin Joseph <abin.joseph@amd.com> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1728491303-1456171-4-git-send-email-radhey.shyam.pandey@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: emaclite: Replace alloc_etherdev() with devm_alloc_etherdev()Abin Joseph2024-10-121-10/+4
| | | | | | | | | | | Use device managed ethernet device allocation to simplify the error handling logic. No functional change. Signed-off-by: Abin Joseph <abin.joseph@amd.com> Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1728491303-1456171-3-git-send-email-radhey.shyam.pandey@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: phy: aquantia: poll status registerAryan Srivastava2024-10-111-3/+16
| | | | | | | | | | | | | | | | | | | | | | | The system interface connection status register is not immediately correct upon line side link up. This results in the status being read as OFF and then transitioning to the correct host side link mode with a short delay. This causes the phylink framework passing the OFF status down to all MAC config drivers, resulting in the host side link being misconfigured, which in turn can lead to link flapping or complete packet loss in some cases. Mitigate this by periodically polling the register until it not showing the OFF state. This will be done every 1ms for 10ms, using the same poll/timeout as the processor intensive operation reads. If the phy is still expressing the OFF state after the timeout, then set the link to false and pass the NA interface mode onto the phylink framework. Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241010004935.1774601-1-aryan.srivastava@alliedtelesis.co.nz Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* eth: remove the DLink/Sundance (ST201) driverJakub Kicinski2024-10-113-2006/+0
| | | | | | | | | | | | | | Konstantin reports the maintainer's address bounces. There is no other maintainer and the driver is quite old. There is a good chance nobody is using this driver any more. Let's try to remove it completely, we can revert it back in if someone complains. Link: https://lore.kernel.org/20240925-bizarre-earwig-from-pluto-1484aa@lemu/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Denis Kirjanov <dkirjanov@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* tg3: Link queues to NAPIsJoe Damato2024-10-111-4/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Link queues to NAPIs using the netdev-genl API so this information is queryable. First, test with the default setting on my tg3 NIC at boot with 1 TX queue: $ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \ --dump queue-get --json='{"ifindex": 2}' [{'id': 0, 'ifindex': 2, 'napi-id': 8194, 'type': 'rx'}, {'id': 1, 'ifindex': 2, 'napi-id': 8195, 'type': 'rx'}, {'id': 2, 'ifindex': 2, 'napi-id': 8196, 'type': 'rx'}, {'id': 3, 'ifindex': 2, 'napi-id': 8197, 'type': 'rx'}, {'id': 0, 'ifindex': 2, 'napi-id': 8193, 'type': 'tx'}] Now, adjust the number of TX queues to be 4 via ethtool: $ sudo ethtool -L eth0 tx 4 $ sudo ethtool -l eth0 | tail -5 Current hardware settings: RX: 4 TX: 4 Other: n/a Combined: n/a Despite "Combined: n/a" in the ethtool output, /proc/interrupts shows the tg3 has renamed the IRQs to be combined: 343: [...] eth0-0 344: [...] eth0-txrx-1 345: [...] eth0-txrx-2 346: [...] eth0-txrx-3 347: [...] eth0-txrx-4 Now query this via netlink to ensure the queues are linked properly to their NAPIs: $ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \ --dump queue-get --json='{"ifindex": 2}' [{'id': 0, 'ifindex': 2, 'napi-id': 8960, 'type': 'rx'}, {'id': 1, 'ifindex': 2, 'napi-id': 8961, 'type': 'rx'}, {'id': 2, 'ifindex': 2, 'napi-id': 8962, 'type': 'rx'}, {'id': 3, 'ifindex': 2, 'napi-id': 8963, 'type': 'rx'}, {'id': 0, 'ifindex': 2, 'napi-id': 8960, 'type': 'tx'}, {'id': 1, 'ifindex': 2, 'napi-id': 8961, 'type': 'tx'}, {'id': 2, 'ifindex': 2, 'napi-id': 8962, 'type': 'tx'}, {'id': 3, 'ifindex': 2, 'napi-id': 8963, 'type': 'tx'}] As you can see above, id 0 for both TX and RX share a NAPI, NAPI ID 8960, and so on for each queue index up to 3. Signed-off-by: Joe Damato <jdamato@fastly.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20241009175509.31753-3-jdamato@fastly.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* tg3: Link IRQs to NAPI instancesJoe Damato2024-10-111-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Link IRQs to NAPI instances with netif_napi_set_irq. This information can be queried with the netdev-genl API. Begin by testing my tg3 device in its default state: 1 TX queue and 4 RX queues. Compare the output of /proc/interrupts for my tg3 device with the output of netdev-genl after applying this patch: $ cat /proc/interrupts | grep eth0 343: [...] eth0-tx-0 344: [...] eth0-rx-1 345: [...] eth0-rx-2 346: [...] eth0-rx-3 347: [...] eth0-rx-4 As you can see above, tg3 has named the IRQs such that there is a dedicated tx IRQ and 4 dedicated rx IRQs, for a total of 5 IRQs. $ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \ --dump napi-get --json='{"ifindex": 2}' [{'id': 8197, 'ifindex': 2, 'irq': 347}, {'id': 8196, 'ifindex': 2, 'irq': 346}, {'id': 8195, 'ifindex': 2, 'irq': 345}, {'id': 8194, 'ifindex': 2, 'irq': 344}, {'id': 8193, 'ifindex': 2, 'irq': 343}] Netlink displays the same IRQs as above, noting that each is mapped to a unique NAPI instance. Now, reconfigure the NIC to have 4 TX queues and 4 RX queues: $ sudo ethtool -L eth0 rx 4 tx 4 $ sudo ethtool -l eth0 | tail -5 Current hardware settings: RX: 4 TX: 4 Other: n/a Combined: n/a Examine /proc/interrupts once again, noting that tg3 will now rename the IRQs to suggest that they are combined tx and rx without allocating additional IRQs, so the total IRQ count in /proc/interrupts is unchanged: 343: [...] eth0-0 344: [...] eth0-txrx-1 345: [...] eth0-txrx-2 346: [...] eth0-txrx-3 347: [...] eth0-txrx-4 Check the output from netlink again: $ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \ --dump napi-get --json='{"ifindex": 2}' [{'id': 8973, 'ifindex': 2, 'irq': 347}, {'id': 8972, 'ifindex': 2, 'irq': 346}, {'id': 8971, 'ifindex': 2, 'irq': 345}, {'id': 8970, 'ifindex': 2, 'irq': 344}, {'id': 8969, 'ifindex': 2, 'irq': 343}] Signed-off-by: Joe Damato <jdamato@fastly.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20241009175509.31753-2-jdamato@fastly.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* r8169: remove original workaround for RTL8125 broken rx issueHeiner Kallweit2024-10-111-4/+0
| | | | | | | | | | | | | Now that we have b9c7ac4fe22c ("r8169: disable ALDPS per default for RTL8125"), the first attempt to fix the issue shouldn't be needed any longer. So let's effectively revert 621735f59064 ("r8169: fix rare issue with broken rx after link-down on RTL8125") and see whether anybody complains. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/382d8c88-cbce-400f-ad62-fda0181c7e38@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* r8169: don't apply UDP padding quirk on RTL8126AHeiner Kallweit2024-10-111-4/+10
| | | | | | | | | | Vendor drivers r8125/r8126 indicate that this quirk isn't needed any longer for RTL8126A. Mimic this in r8169. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/d1317187-aa81-4a69-b831-678436e4de62@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2024-10-1049-183/+372
|\ | | | | | | | | | | | | | | Cross-merge networking fixes after downstream PR (net-6.12-rc3). No conflicts and no adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * slip: make slhc_remember() more robust against malicious packetsEric Dumazet2024-10-101-23/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | syzbot found that slhc_remember() was missing checks against malicious packets [1]. slhc_remember() only checked the size of the packet was at least 20, which is not good enough. We need to make sure the packet includes the IPv4 and TCP header that are supposed to be carried. Add iph and th pointers to make the code more readable. [1] BUG: KMSAN: uninit-value in slhc_remember+0x2e8/0x7b0 drivers/net/slip/slhc.c:666 slhc_remember+0x2e8/0x7b0 drivers/net/slip/slhc.c:666 ppp_receive_nonmp_frame+0xe45/0x35e0 drivers/net/ppp/ppp_generic.c:2455 ppp_receive_frame drivers/net/ppp/ppp_generic.c:2372 [inline] ppp_do_recv+0x65f/0x40d0 drivers/net/ppp/ppp_generic.c:2212 ppp_input+0x7dc/0xe60 drivers/net/ppp/ppp_generic.c:2327 pppoe_rcv_core+0x1d3/0x720 drivers/net/ppp/pppoe.c:379 sk_backlog_rcv+0x13b/0x420 include/net/sock.h:1113 __release_sock+0x1da/0x330 net/core/sock.c:3072 release_sock+0x6b/0x250 net/core/sock.c:3626 pppoe_sendmsg+0x2b8/0xb90 drivers/net/ppp/pppoe.c:903 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4091 [inline] slab_alloc_node mm/slub.c:4134 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4186 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:587 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:678 alloc_skb include/linux/skbuff.h:1322 [inline] sock_wmalloc+0xfe/0x1a0 net/core/sock.c:2732 pppoe_sendmsg+0x3a7/0xb90 drivers/net/ppp/pppoe.c:867 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 0 UID: 0 PID: 5460 Comm: syz.2.33 Not tainted 6.12.0-rc2-syzkaller-00006-g87d6aab2389e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Fixes: b5451d783ade ("slip: Move the SLIP drivers") Reported-by: syzbot+2ada1bc857496353be5a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/670646db.050a0220.3f80e.0027.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20241009091132.2136321-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * ppp: fix ppp_async_encode() illegal accessEric Dumazet2024-10-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | syzbot reported an issue in ppp_async_encode() [1] In this case, pppoe_sendmsg() is called with a zero size. Then ppp_async_encode() is called with an empty skb. BUG: KMSAN: uninit-value in ppp_async_encode drivers/net/ppp/ppp_async.c:545 [inline] BUG: KMSAN: uninit-value in ppp_async_push+0xb4f/0x2660 drivers/net/ppp/ppp_async.c:675 ppp_async_encode drivers/net/ppp/ppp_async.c:545 [inline] ppp_async_push+0xb4f/0x2660 drivers/net/ppp/ppp_async.c:675 ppp_async_send+0x130/0x1b0 drivers/net/ppp/ppp_async.c:634 ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2280 [inline] ppp_input+0x1f1/0xe60 drivers/net/ppp/ppp_generic.c:2304 pppoe_rcv_core+0x1d3/0x720 drivers/net/ppp/pppoe.c:379 sk_backlog_rcv+0x13b/0x420 include/net/sock.h:1113 __release_sock+0x1da/0x330 net/core/sock.c:3072 release_sock+0x6b/0x250 net/core/sock.c:3626 pppoe_sendmsg+0x2b8/0xb90 drivers/net/ppp/pppoe.c:903 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4092 [inline] slab_alloc_node mm/slub.c:4135 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4187 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:587 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:678 alloc_skb include/linux/skbuff.h:1322 [inline] sock_wmalloc+0xfe/0x1a0 net/core/sock.c:2732 pppoe_sendmsg+0x3a7/0xb90 drivers/net/ppp/pppoe.c:867 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 1 UID: 0 PID: 5411 Comm: syz.1.14 Not tainted 6.12.0-rc1-syzkaller-00165-g360c1f1f24c6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+1d121645899e7692f92a@syzkaller.appspotmail.com Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20241009185802.3763282-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * vxlan: Handle error of rtnl_register_module().Kuniyuki Iwashima2024-10-103-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since introduced, vxlan_vnifilter_init() has been ignoring the returned value of rtnl_register_module(), which could fail silently. Handling the error allows users to view a module as an all-or-nothing thing in terms of the rtnetlink functionality. This prevents syzkaller from reporting spurious errors from its tests, where OOM often occurs and module is automatically loaded. Let's handle the errors by rtnl_register_many(). Fixes: f9c4bb0b245c ("vxlan: vni filtering support on collect metadata device") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * Merge branch '100GbE' of ↵Jakub Kicinski2024-10-1011-35/+31
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-10-08 (ice, i40e, igb, e1000e) This series contains updates to ice, i40e, igb, and e1000e drivers. For ice: Marcin allows driver to load, into safe mode, when DDP package is missing or corrupted and adjusts the netif_is_ice() check to account for when the device is in safe mode. He also fixes an out-of-bounds issue when MSI-X are increased for VFs. Wojciech clears FDB entries on reset to match the hardware state. For i40e: Aleksandr adds locking around MACVLAN filters to prevent memory leaks due to concurrency issues. For igb: Mohamed Khalfella adds a check to not attempt to bring up an already running interface on non-fatal PCIe errors. For e1000e: Vitaly changes board type for I219 to more closely match the hardware and stop PHY issues. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: e1000e: change I219 (19) devices to ADP igb: Do not bring the device up after non-fatal error i40e: Fix macvlan leak by synchronizing access to mac_filter_hash ice: Fix increasing MSI-X on VF ice: Flush FDB entries before reset ice: Fix netif_is_ice() in Safe Mode ice: Fix entering Safe Mode ==================== Link: https://patch.msgid.link/20241008230050.928245-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| | * e1000e: change I219 (19) devices to ADPVitaly Lifshits2024-10-082-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sporadic issues, such as PHY access loss, have been observed on I219 (19) devices. It was found that these devices have hardware more closely related to ADP than MTP and the issues were caused by taking MTP-specific flows. Change the MAC and board types of these devices from MTP to ADP to correctly reflect the LAN hardware, and flows, of these devices. Fixes: db2d737d63c5 ("e1000e: Separate MTP board type from ADP") Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * igb: Do not bring the device up after non-fatal errorMohamed Khalfella2024-10-081-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 004d25060c78 ("igb: Fix igb_down hung on surprise removal") changed igb_io_error_detected() to ignore non-fatal pcie errors in order to avoid hung task that can happen when igb_down() is called multiple times. This caused an issue when processing transient non-fatal errors. igb_io_resume(), which is called after igb_io_error_detected(), assumes that device is brought down by igb_io_error_detected() if the interface is up. This resulted in panic with stacktrace below. [ T3256] igb 0000:09:00.0 haeth0: igb: haeth0 NIC Link is Down [ T292] pcieport 0000:00:1c.5: AER: Uncorrected (Non-Fatal) error received: 0000:09:00.0 [ T292] igb 0000:09:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID) [ T292] igb 0000:09:00.0: device [8086:1537] error status/mask=00004000/00000000 [ T292] igb 0000:09:00.0: [14] CmpltTO [ 200.105524,009][ T292] igb 0000:09:00.0: AER: TLP Header: 00000000 00000000 00000000 00000000 [ T292] pcieport 0000:00:1c.5: AER: broadcast error_detected message [ T292] igb 0000:09:00.0: Non-correctable non-fatal error reported. [ T292] pcieport 0000:00:1c.5: AER: broadcast mmio_enabled message [ T292] pcieport 0000:00:1c.5: AER: broadcast resume message [ T292] ------------[ cut here ]------------ [ T292] kernel BUG at net/core/dev.c:6539! [ T292] invalid opcode: 0000 [#1] PREEMPT SMP [ T292] RIP: 0010:napi_enable+0x37/0x40 [ T292] Call Trace: [ T292] <TASK> [ T292] ? die+0x33/0x90 [ T292] ? do_trap+0xdc/0x110 [ T292] ? napi_enable+0x37/0x40 [ T292] ? do_error_trap+0x70/0xb0 [ T292] ? napi_enable+0x37/0x40 [ T292] ? napi_enable+0x37/0x40 [ T292] ? exc_invalid_op+0x4e/0x70 [ T292] ? napi_enable+0x37/0x40 [ T292] ? asm_exc_invalid_op+0x16/0x20 [ T292] ? napi_enable+0x37/0x40 [ T292] igb_up+0x41/0x150 [ T292] igb_io_resume+0x25/0x70 [ T292] report_resume+0x54/0x70 [ T292] ? report_frozen_detected+0x20/0x20 [ T292] pci_walk_bus+0x6c/0x90 [ T292] ? aer_print_port_info+0xa0/0xa0 [ T292] pcie_do_recovery+0x22f/0x380 [ T292] aer_process_err_devices+0x110/0x160 [ T292] aer_isr+0x1c1/0x1e0 [ T292] ? disable_irq_nosync+0x10/0x10 [ T292] irq_thread_fn+0x1a/0x60 [ T292] irq_thread+0xe3/0x1a0 [ T292] ? irq_set_affinity_notifier+0x120/0x120 [ T292] ? irq_affinity_notify+0x100/0x100 [ T292] kthread+0xe2/0x110 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork+0x2d/0x50 [ T292] ? kthread_complete_and_exit+0x20/0x20 [ T292] ret_from_fork_asm+0x11/0x20 [ T292] </TASK> To fix this issue igb_io_resume() checks if the interface is running and the device is not down this means igb_io_error_detected() did not bring the device down and there is no need to bring it up. Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com> Fixes: 004d25060c78 ("igb: Fix igb_down hung on surprise removal") Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * i40e: Fix macvlan leak by synchronizing access to mac_filter_hashAleksandr Loktionov2024-10-082-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch addresses a macvlan leak issue in the i40e driver caused by concurrent access to vsi->mac_filter_hash. The leak occurs when multiple threads attempt to modify the mac_filter_hash simultaneously, leading to inconsistent state and potential memory leaks. To fix this, we now wrap the calls to i40e_del_mac_filter() and zeroing vf->default_lan_addr.addr with spin_lock/unlock_bh(&vsi->mac_filter_hash_lock), ensuring atomic operations and preventing concurrent access. Additionally, we add lockdep_assert_held(&vsi->mac_filter_hash_lock) in i40e_add_mac_filter() to help catch similar issues in the future. Reproduction steps: 1. Spawn VFs and configure port vlan on them. 2. Trigger concurrent macvlan operations (e.g., adding and deleting portvlan and/or mac filters). 3. Observe the potential memory leak and inconsistent state in the mac_filter_hash. This synchronization ensures the integrity of the mac_filter_hash and prevents the described leak. Fixes: fed0d9f13266 ("i40e: Fix VF's MAC Address change on VM") Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * ice: Fix increasing MSI-X on VFMarcin Szycik2024-10-083-5/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Increasing MSI-X value on a VF leads to invalid memory operations. This is caused by not reallocating some arrays. Reproducer: modprobe ice echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count Default MSI-X is 16, so 17 and above triggers this issue. KASAN reports: BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] Read of size 8 at addr ffff8888b937d180 by task bash/28433 (...) Call Trace: (...) ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] kasan_report+0xed/0x120 ? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice] ice_vsi_cfg_def+0x3360/0x4770 [ice] ? mutex_unlock+0x83/0xd0 ? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice] ? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vf_reconfig_vsi+0x114/0x210 [ice] ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice] sriov_vf_msix_count_store+0x21c/0x300 (...) Allocated by task 28201: (...) ice_vsi_cfg_def+0x1c8e/0x4770 [ice] ice_vsi_cfg+0x7f/0x3b0 [ice] ice_vsi_setup+0x179/0xa30 [ice] ice_sriov_configure+0xcaa/0x1520 [ice] sriov_numvfs_store+0x212/0x390 (...) To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This causes the required arrays to be reallocated taking the new queue count into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq before ice_vsi_rebuild(), so that realloc uses the newly set queue count. Additionally, ice_vsi_rebuild() does not remove VSI filters (ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer necessary. Reported-by: Jacob Keller <jacob.e.keller@intel.com> Fixes: 2a2cb4c6c181 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * ice: Flush FDB entries before resetWojciech Drewek2024-10-083-22/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Triggering the reset while in switchdev mode causes errors[1]. Rules are already removed by this time because switch content is flushed in case of the reset. This means that rules were deleted from HW but SW still thinks they exist so when we get SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to delete not existing rule. We can avoid these errors by clearing the rules early in the reset flow before they are removed from HW. Switchdev API will get notified that the rule was removed so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification. Remove unnecessary ice_clear_sw_switch_recipes. [1] ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2 ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2 Fixes: 7c945a1a8e5f ("ice: Switchdev FDB events support") Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * ice: Fix netif_is_ice() in Safe ModeMarcin Szycik2024-10-081-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | netif_is_ice() works by checking the pointer to netdev ops. However, it only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops, so in Safe Mode it always returns false, which is unintuitive. While it doesn't look like netif_is_ice() is currently being called anywhere in Safe Mode, this could change and potentially lead to unexpected behaviour. Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| | * ice: Fix entering Safe ModeMarcin Szycik2024-10-081-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If DDP package is missing or corrupted, the driver should enter Safe Mode. Instead, an error is returned and probe fails. To fix this, don't exit init if ice_init_ddp_config() returns an error. Repro: * Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg) * Load ice Fixes: cc5776fe1832 ("ice: Enable switching default Tx scheduler topology") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
| * | net: netconsole: fix wrong warningBreno Leitao2024-10-101-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A warning is triggered when there is insufficient space in the buffer for userdata. However, this is not an issue since userdata will be sent in the next iteration. Current warning message: ------------[ cut here ]------------ WARNING: CPU: 13 PID: 3013042 at drivers/net/netconsole.c:1122 write_ext_msg+0x3b6/0x3d0 ? write_ext_msg+0x3b6/0x3d0 console_flush_all+0x1e9/0x330 The code incorrectly issues a warning when this_chunk is zero, which is a valid scenario. The warning should only be triggered when this_chunk is negative. Fixes: 1ec9daf95093 ("net: netconsole: append userdata to fragmented netconsole messages") Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20241008094325.896208-1-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | net: fec: don't save PTP state if PTP is unsupportedWei Fang2024-10-101-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some platforms (such as i.MX25 and i.MX27) do not support PTP, so on these platforms fec_ptp_init() is not called and the related members in fep are not initialized. However, fec_ptp_save_state() is called unconditionally, which causes the kernel to panic. Therefore, add a condition so that fec_ptp_save_state() is not called if PTP is not supported. Fixes: a1477dc87dc4 ("net: fec: Restart PPS after link state change") Reported-by: Guenter Roeck <linux@roeck-us.net> Closes: https://lore.kernel.org/lkml/353e41fe-6bb4-4ee9-9980-2da2a9c1c508@roeck-us.net/ Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Csókás, Bence <csokas.bence@prolan.hu> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Guenter Roeck <linux@roeck-us.net> Link: https://patch.msgid.link/20241008061153.1977930-1-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | net: ibm: emac: mal: add dcr_unmap to _removeRosen Penev2024-10-101-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's done in probe so it should be undone here. Fixes: 1d3bb996481e ("Device tree aware EMAC driver") Signed-off-by: Rosen Penev <rosenp@gmail.com> Reviewed-by: Breno Leitao <leitao@debian.org> Link: https://patch.msgid.link/20241008233050.9422-1-rosenp@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | net: ftgmac100: fixed not check status from fixed phyJacky Chou2024-10-101-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add error handling from calling fixed_phy_register. It may return some error, therefore, need to check the status. And fixed_phy_register needs to bind a device node for mdio. Add the mac device node for fixed_phy_register function. This is a reference to this function, of_phy_register_fixed_link(). Fixes: e24a6c874601 ("net: ftgmac100: Get link speed and duplex for NC-SI") Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com> Link: https://patch.msgid.link/20241007032435.787892-1-jacky_chou@aspeedtech.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * | net: amd: mvme147: Fix probe banner messageDaniel Palmer2024-10-091-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently this driver prints this line with what looks like a rogue format specifier when the device is probed: [ 2.840000] eth%d: MVME147 at 0xfffe1800, irq 12, Hardware Address xx:xx:xx:xx:xx:xx Change the printk() for netdev_info() and move it after the registration has completed so it prints out the name of the interface properly. Signed-off-by: Daniel Palmer <daniel@0x0f.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: phy: realtek: Fix MMD access on RTL8126A-integrated PHYHeiner Kallweit2024-10-091-1/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All MMD reads return 0 for the RTL8126A-integrated PHY. Therefore phylib assumes it doesn't support EEE, what results in higher power consumption, and a significantly higher chip temperature in my case. To fix this split out the PHY driver for the RTL8126A-integrated PHY and set the read_mmd/write_mmd callbacks to read from vendor-specific registers. Fixes: 5befa3728b85 ("net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY") Cc: stable@vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: ti: icssg-prueth: Fix race condition for VLAN table accessMD Danish Anwar2024-10-093-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VLAN table is a shared memory between the two ports/slices in a ICSSG cluster and this may lead to race condition when the common code paths for both ports are executed in different CPUs. Fix the race condition access by locking the shared memory access Fixes: 487f7323f39a ("net: ti: icssg-prueth: Add helper functions to configure FDB") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: ibm: emac: mal: fix wrong gotoRosen Penev2024-10-091-1/+1
| |/ | | | | | | | | | | | | | | | | dcr_map is called in the previous if and therefore needs to be unmapped. Fixes: 1ff0fcfcb1a6 ("ibm_newemac: Fix new MAL feature handling") Signed-off-by: Rosen Penev <rosenp@gmail.com> Link: https://patch.msgid.link/20241007235711.5714-1-rosenp@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: dsa: b53: fix jumbo frames on 10/100 portsJonas Gorski2024-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All modern chips support and need the 10_100 bit set for supporting jumbo frames on 10/100 ports, so instead of enabling it only for 583XX enable it for everything except bcm63xx, where the bit is writeable, but does nothing. Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds without the bit set. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: dsa: b53: allow lower MTUs on BCM5325/5365Jonas Gorski2024-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | While BCM5325/5365 do not support jumbo frames, they do support slightly oversized frames, so do not error out if requesting a supported MTU for them. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: dsa: b53: fix max MTU for BCM5325/BCM5365Jonas Gorski2024-10-081-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | BCM5325/BCM5365 do not support jumbo frames, so we should not report a jumbo frame mtu for them. But they do support so called "oversized" frames up to 1536 bytes long by default, so report an appropriate MTU. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: dsa: b53: fix max MTU for 1g switchesJonas Gorski2024-10-081-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload without ethernet headers. According to the datasheets maximum supported frame length for most gigabyte swithes is 9720 bytes, so convert that to the expected MTU when using VLAN tagged frames. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: dsa: b53: fix jumbo frame mtu checkJonas Gorski2024-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the data payload size. Comparing these two meant that mtus between 1500 and 1518 did not trigger enabling jumbo frames. So instead compare the set mtu ETH_DATA_LEN, which is equal to JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN; Also do a check that the requested mtu is actually greater than the minimum length, else we do not need to enable jumbo frames. In practice this only introduced a very small range of mtus that did not work properly. Newer chips allow 2000 byte large frames by default, and older chips allow 1536 bytes long, which is equivalent to an mtu of 1514. So effectivly only mtus of 1515~1517 were broken. Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: ethernet: ti: am65-cpsw: avoid devm_alloc_etherdev, fix module removalNicolas Pitre2024-10-081-8/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Usage of devm_alloc_etherdev_mqs() conflicts with am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances get unregistered twice. Switch to alloc_etherdev_mqs() and make sure am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device instances properly. With this, it is finally possible to rmmod the driver without oopsing the kernel. Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Nicolas Pitre <npitre@baylibre.com> Reviewed-by: Roger Quadros <roger@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: ethernet: ti: am65-cpsw: prevent WARN_ON upon module removalNicolas Pitre2024-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink() after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in devl_port_unregister(). Makes it coherent with usage in m65_cpsw_nuss_register_ndevs()'s cleanup path. Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support") Signed-off-by: Nicolas Pitre <npitre@baylibre.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
| * net: airoha: Update tx cpu dma ring idx at the end of xmit loopLorenzo Bianconi2024-10-081-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | Move the tx cpu dma ring index update out of transmit loop of airoha_dev_xmit routine in order to not start transmitting the packet before it is fully DMA mapped (e.g. fragmented skbs). Fixes: 23020f049327 ("net: airoha: Introduce ethernet support for EN7581 SoC") Reported-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20241004-airoha-eth-7581-mapping-fix-v1-1-8e4279ab1812@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: phy: Remove LED entry from LEDs list on unregisterChristian Marangi2024-10-081-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering") correctly fixed a problem with using devm_ but missed removing the LED entry from the LEDs list. This cause kernel panic on specific scenario where the port for the PHY is torn down and up and the kmod for the PHY is removed. On setting the port down the first time, the assosiacted LEDs are correctly unregistered. The associated kmod for the PHY is now removed. The kmod is now added again and the port is now put up, the associated LED are registered again. On putting the port down again for the second time after these step, the LED list now have 4 elements. With the first 2 already unregistered previously and the 2 new one registered again. This cause a kernel panic as the first 2 element should have been removed. Fix this by correctly removing the element when LED is unregistered. Reported-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Cc: stable@vger.kernel.org Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ethernet: adi: adin1110: Fix some error handling path in ↵Christophe JAILLET2024-10-081-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | adin1110_read_fifo() If 'frame_size' is too small or if 'round_len' is an error code, it is likely that an error code should be returned to the caller. Actually, 'ret' is likely to be 0, so if one of these sanity checks fails, 'success' is returned. Return -EINVAL instead. Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://patch.msgid.link/8ff73b40f50d8fa994a454911b66adebce8da266.1727981562.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * Revert "net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled"Jakub Kicinski2024-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c. The commit describes that we don't have to sync the page when recycling, and it tries to optimize that case. But we do need to sync after allocation. Recycling side should be changed to pass the right sync size instead. Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled") Reported-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/20241004070846.2502e9ea@kernel.org Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Furong Xu <0x1207@gmail.com> Link: https://patch.msgid.link/20241004142115.910876-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-02 09:56:12 +0100