summaryrefslogtreecommitdiffstats
path: root/drivers/nfc (follow)
Commit message (Collapse)AuthorAgeFilesLines
* NFC: st21nfca: Adding P2P support to st21nfca in Initiator & Target modeChristophe Ricard2014-07-235-3/+993
| | | | | | | | | | | | | | | | | | | | | | | | | Support for Initiator and Target mode with ISO18092 commands support: - ATR_REQ/ATR_RES - PSL_REQ/PSL_RES - DEP_REQ/DEP_RES Work based on net/nfc/digital_dep.c. st21nfca is using: - Gate reader F for P2P in initiator mode. - Gate card F for P2P in target mode. Felica tag and p2p are differentiated with NFCID2. When starting with 01FE it is acting in p2p mode. On complete_target_discovered on ST21NFCA_RF_READER_F_GATE supported_protocols is set to NFC_PROTO_NFC_DEP_MASK for P2P. Tested against: Nexus S, Galaxy S2, Galaxy S3, Galaxy S3 Mini, Nexus 4 & Nexus 5. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Implement stop_poll HCI hookChristophe Ricard2014-07-231-0/+8
| | | | | | | | | | | | | | | | | Send DM_DISCONNECT command to disconnect Terminal Host from the HCI network. - The persistent states of the terminal host pipes, including registry values, are not modifies. Therefore, there is no NVRAM update to disconnect the terminal host. - The terminal host RF card gates are disabled which means that there will be no event related to card RF gates until communication has been restored. - The terminal host RF reader request is reset so the RF reader polling for terminal host is disabled. To restore the communication, the terminal host can send any HCI command or event. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Improve read length sequence for P2P mode.Christophe Ricard2014-07-231-1/+1
| | | | | | | | | | | A DEP_RES with a SUPERVISOR PDU can be up to 16 bytes long. In order to avoid useless read during p2p, extend first read sequence to 16 and reduce third sequence to 12 to keep same total on the full sequence. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Improved start of frame detectionChristophe Ricard2014-07-231-3/+2
| | | | | | | | | A start of frame is 7E 00 not only 7E. Make sure the first read sequence is starting with 7E 00. For example: 7E FF FF FF FF is as a correct crc but it is a bad frame. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Free buffer in case no data are retrieved.Christophe Ricard2014-07-231-0/+2
| | | | | | | In case no data are retrieve through i2c or one specific case is not handled. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfcb: few code clean upChristophe Ricard2014-07-231-8/+8
| | | | | Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfcb: Add driver for STMicroelectronics ST21NFCB NFC chipChristophe Ricard2014-07-239-2/+1015
| | | | | | | | | | | | | | | | | | | | | | | | Add driver for STMicroelectronics ST21NFCB NFC controller. ST21NFCB is using NCI protocol and a proprietary low level transport protocol called NDLC used on top. NDLC: The protocol defines 2 types of frame: - One type carrying NCI data (referred as DATAFRAME frames). - One type carrying protocol information used for flow control and error control mechanisms (referred as SUPERVISOR frames). After each frame transmission to the NFC controller, the device host SHALL waitfor an ACK (SUPERVISOR frame) reception before sending a new frame. The NFC controller MAY send a frame at anytime to the device host. The NFC controller MAY send a specific WAIT supervisor frame to indicate to device host that a NCI data packet has been received but that it could take significant time before the NFC controller sends an ACK and thus allows next data reception. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add support for Felica Type 3 tagsMark A. Greer2014-05-261-1/+12
| | | | | | | | Add support for the Felica protocol and Type 3 tags. Both 212 and 424 kbps are supported. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: port100: Add support for type 4B tagThierry Escande2014-05-261-1/+35
| | | | | | | | | This patch adds support for ISO-DEP protocol over NFC-B rf technology by adding NFC_PROTO_ISO14443_B to the supported protocols and an entry for framing configuration. Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Add ISO15693 Reader/Writer supportChristophe Ricard2014-05-201-1/+72
| | | | | | | | Add support for ISO/IEC 15693 RF technology and Type 5 tags. ISO15963 is using proprietary gate 12. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Improve load_sessionChristophe Ricard2014-05-201-2/+19
| | | | | | | | | In case anybody uses previous patchset with the CLF, add a check to make sure missing pipe are created. st21nfca returns its pipe list in the creation order (most recent latest). Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: dts: st21nfca: Add device-tree (Open Firmware) support to st21nfcaChristophe Ricard2014-05-201-19/+87
| | | | | | | | | | Add functions to recover hardware resources from the device-tree when not provided by the platform data. Based on pn544 devicetree implementation Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Free buffer when a bad frame is detectedChristophe Ricard2014-05-051-0/+1
| | | | | | | | When a bad frame is detected for a bad crc. We were reallocating and loosing the previous frame pointer. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Synchronize i2c Tx and Rx pathChristophe Ricard2014-05-051-0/+6
| | | | | | | | | Stabilize communication by using a mutex. This avoids running a write transaction during a read retry or a read transaction during a write retry. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Improved i2c Rx data correctness checkChristophe Ricard2014-05-051-3/+26
| | | | | | | | | | | | | | | | | | | | A frame starts with ST21NFCA_SOF_EOF(0x7e) + 0x00. A frame ends with ST21NFCA_SOF_EOF(0x7e). It is possible that the i2c macrocell is stopped for other communication interfaces with highest priority(RF or SWP). This can be seen with some 0xFF data at the end of a received shdlc buffer. If this happen we need to discard the frame because the CLF will repeat it. In order to push accurate data to hci layer, we add the following fix: - Instead of looking for the first 0x7e in the frame, check that the last received byte is 0x7e. - Check that the first frame reception block start with start of frame(0x7e 0x00). If not, clear the buffer. - Check that the next frame reception block do not start with start of frame(0x7e). If so, clear the buffer. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Fix st21nfca_hci_remove_len_crc tail room handlingChristophe Ricard2014-05-051-12/+9
| | | | | | | | | | | | | There is no byte stuffing when data are stored in skb. TAILROOM is 2 byte crc + 1 byte eof. st21nfca_hci_remove_len_crc was doing an incorrect operation on the TAILROOM data. If shdlc timer T2 is triggered, it will request to send the same data. Before every hci data was lost after st21nfca_hci_remove_len_crc. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Fix incorrect byte stuffing revocationChristophe Ricard2014-05-051-4/+3
| | | | | | | | | Byte stuffing was not correctly removed after a i2c read operation. This was causing improper crc calculation when byte stuffing was applied to more than 1 byte. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Remove few useless includeChristophe Ricard2014-05-051-11/+0
| | | | | | | Remove unneeded includes from i2c.c Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Improve st21nfca initialization by handling reboot properlyChristophe Ricard2014-04-221-8/+39
| | | | | | | | | | Change in st21nfca_hci_platform_init in order to handle in a better way the internal reboot command. Once the reboot is completed, the driver expect to receive a 0x7e filled buffer. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Reworked st21nfca_request_resourcesChristophe Ricard2014-04-221-16/+26
| | | | | | | | Remove struct st21nfca_i2c_phy* as this parameter can be retrieve through i2c_get_clientdata(client) Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: st21nfca_hci_i2c_probe returns st21nfca_hci_probe result.Christophe Ricard2014-04-221-6/+1
| | | | | | | | | | | st21nfca_hci_probe return 0 in case of successful call and a different value in any other cases. There is no need to check for st21nfca_hci_probe return as this will be checked after st21nfca_hci_i2c_probe is completed. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Add __packed to struct st21nfca_pipe_infoChristophe Ricard2014-04-221-1/+1
| | | | | Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Remove sporadic wait_tab variable from functions.Christophe Ricard2014-04-221-4/+3
| | | | | | | wait_tab variable is already global and may create conflicts. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Fix warning: array subscript is above array boundsChristophe Ricard2014-04-221-3/+3
| | | | | | | Fix "warning: array subscript is above array bounds" in load_session Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Fix sparse: cast to restricted __be16Christophe Ricard2014-04-221-1/+1
| | | | | | | | Fixing "sparse: cast to restricted __be16" message when building with make C=1 CF=-D__CHECK_ENDIAN__ Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: pn544_i2c: Fix null pointer exception when not using platform dataClement Perrochaud2014-04-221-1/+5
| | | | | | | | Fixes a null pointer exception occurring when the IRQ request in pn544_hci_i2c_probe fails and no platform data is available. Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add support for the ISO/IEC 14443-B and Type 4B tagsMark A. Greer2014-04-221-1/+7
| | | | | | | | | Now that the NFC digital layer has support for the ISO/IEC 14443-B protocol and type 4B tags, add the corresponding support to the trf7970a driver. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add 'autosuspend-delay' DTS propertyMark A. Greer2014-04-221-2/+17
| | | | | | | | | | The trf7970a driver currently uses a fixed autosuspend delay of 30 seconds. To enable users to customize the delay as they see fit, add support for the new 'autosuspend-delay' DTS property (part of the nfc node) which can override the default 30 seconds. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Don't return value from trf7970a_switch_rf_on()Mark A. Greer2014-04-221-13/+6
| | | | | | | | trf7970a_switch_rf_on() no longer returns anything other than 0 so make it void and clean up the code that checks for errors when its called. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add pm_runtime supportMark A. Greer2014-04-221-37/+85
| | | | | | | | | | | | | | | | | Add pm_runtime support by moving the code that enables the trf7970a to the pm_runtime hook routines. The pm_runtime 'autosuspend' feature is used so that the device isn't disabled until at least 30 seconds have passed since trf7970a_switch_rf_off() was last called. The result is that when trf7970a_switch_rf_on() is called, the device will be enabled and initialized (if it isn't already). When trf7970a_switch_rf_off() is called, it will turn off the RF immediately but leave the device enabled for at least 30 seconds. If 30 seconds have passed and the pm_runtime facility decides to suspend the driver, the device will be disabled then. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Turn RF on after hardware is configuredMark A. Greer2014-04-221-5/+16
| | | | | | | | | | The NFC digital layer calls the 'switch_rf' hook to turn the RF on before it configures the RF technology and framing. There is potential to confuse a tag doing it this way so don't enable the RF until the RF technology and initial framing have been configured. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Set correct Vin voltage in Chip Status Control registerMark A. Greer2014-04-221-3/+8
| | | | | | | | | | Currently, the trf7970a driver assumes that the Vin voltage is 5V when it writes to the 'Chip Status Control' register. That may not be correct so use the regulator facility to get the Vin voltage and set the VRS5_3 bit correctly when writing to that register. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Allow different Modulator and SYS_CLK Control register valuesMark A. Greer2014-04-221-1/+4
| | | | | | | | | | | | Currently the driver writes the same value to the 'Modulator and SYS_CLK Control' register no matter what RF technology is being used. That works for now but new RF technologies (e.g., ISO/IEC 14443-B) will require different values to be written to that register. To support this, add a member to the trf7970a structure which is set by the RF technology handling code and used by the framing code when it writes to that register. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Set 'Modulator and SYS_CLK Control' after 'ISO Control'Mark A. Greer2014-04-221-5/+5
| | | | | | | | | | | | | Writing to the 'ISO Control' register may cause the contents of the 'Modulator and SYS_CLK Control' register to change so be sure to write to 'Modulator and SYS_CLK Control' after writing to 'ISO Control'. Note that writing to the 'Modulator and SYS_CLK Control' register shouldn't be necessary at all according to the trf790a manual but testing shows that it is necessary. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Only write 'ISO Control' when its changingMark A. Greer2014-04-221-6/+19
| | | | | | | | | | The current code always writes to the 'ISO Control' register when the RF framing is set. That's not necessary since the register's value doesn't always change. Instead, only write to it when its value is actually being changed. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Reset FIFO when 'End of TX' Interrupt OccursMark A. Greer2014-04-221-1/+3
| | | | | | | | | | Sometimes after sending a frame there is tx data leftover in the FIFO which the driver will think is part of the receive frame. That data can be cleared when an 'End of TX' interrupt is received by issuing the 'FIFO Reset' command. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Clear 'NFC Target Detection Level' registerMark A. Greer2014-04-221-0/+5
| | | | | | | | Due to a trf7970a erratum, the 'NFC Target Detection Level' register (0x18) must be cleared after power-up. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Only abort a command if one is activeMark A. Greer2014-04-221-1/+12
| | | | | | | | | | Only initiate the abort command process when there is an active command. If the abort process were started and there wasn't an active command then the next command issued by the digital layer would be incorrectly aborted. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Increase TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT to 20 msMark A. Greer2014-04-221-5/+5
| | | | | | | | | | | | After further testing periods of ~16 ms have been observed between interrupts indicating that there is receive data in the FIFO. To accomodate that, increase the time the driver waits before deciding there is no more data to receive to 20 ms. The macro that represents that delay is 'TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT'. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: pn544: i2c: Add device-tree (Open Firmware) support to PN544Clement Perrochaud2014-04-221-17/+131
| | | | | | | | Add functions to recover hardware resources from the device-tree when not provided by the platform data. Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: st21nfca: Implement load_session HCI hookChristophe Ricard2014-04-221-1/+116
| | | | | | | | | | | | | | | This implementation rely on the ST21NFCA_DEVICE_MGNT_GATE and ST21NFCA_DM_GETINFO proprietary gates commands. First we are retrieving a pipe list available on the CLF with the ST21NFCA_DM_GETINFO_PIPE_LIST parameter. A gate<->pipe table match is done with ST21NFCA_DM_GETINFO_PIPE_INFO for each pipe. If the pipe is created and open, we fill st21nfca_gates table. If the pipe is create but closed or is not created we keep the gate with NFC_HCI_INVALID_PIPE. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC ChipChristophe Ricard2014-04-227-0/+1221
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add driver for STMicroelectronics ST21NFCA NFC controller. ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as communication protocol. Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B. It is using proprietary gate 15 for ISO14443-3 such as type 1 & type 2 tags. It is using proprietary gate 14 for type F tags. ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration. Standard gate for ISO14443-4 A (13) & B (11) are also used. ST21NFCA specific mecanism: One particular point to notice for the data handling is that frame does not contain any length value. Therefore the i2c part of this driver is managing the reception with a read length sequence until the end of frame (0x7e) is reached. In order to avoid conflict between sof & eof a mecanism called byte stuffing concist of an escape byte (0x7d) insertion before special byte (0x7e, 0x7d). The special byte is then xored with 0x20. In this driver, When data are available in the CLF, the interrupt gpio is driven to active state and triggered an interrupt. Once the i2c_master_recv start, the interrupt gpio is driven to idle state until its complete. If the frame is incomplete or data are still available, interrupts will be triggered again. Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add ISO/IEC 15693 and Type 5 tag SupportMark A. Greer2014-03-111-4/+148
| | | | | | | | | | Add support for ISO/IEC 15693 RF technology and Type 5 tags. Note that Type 5 tags used to be referred to as Type V tags. CC: Erick Macias <emacias@ti.com> CC: Felipe Balbi <balbi@ti.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add support for Type 4A TagsMark A. Greer2014-03-111-1/+3
| | | | | | | | | Add support for Type 4A Tags which includes supporting the underlying ISO/IEC 14443-A protocol. Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: trf7970a: Add driver with ISO/IEC 14443 Type 2 Tag SupportMark A. Greer2014-03-113-0/+1237
| | | | | | | | | | | Add a driver for the Texas Instruments TRF7970a RFID/NFC/15693 transceiver. The driver currently supports ISO/IEC 14443 Type 2 tags only (MIFARE Ultralight and Ultralight C but not Classic). CC: Erick Macias <emacias@ti.com> CC: Felipe Balbi <balbi@ti.com> Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: pn533: Convert to use USB_DEVICE macroAxel Lin2014-02-231-20/+8
| | | | | Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: port100: Convert to use USB_DEVICE macroAxel Lin2014-02-231-4/+1
| | | | | Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: port100: Add support for type 4A tag platformThierry Escande2014-02-161-1/+6
| | | | | | | | | | | This adds support for ISO-DEP protocol over NFC-A rf technology. The port100 already supports NFC-A and ATS request and response for type 4A tags are handled at digital level. This patch adds NFC_PROTO_ISO14443 to the supported protocols and an entry for framing configuration which is the same as NFC-A standard frame with CRC handling. Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: port100: Fix possible buffer overflowThierry Escande2014-02-161-0/+13
| | | | | | | | | The arrays for protocols and rf techs must define a number of entries corresponding to their maximum possible index values. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* NFC: pn544: i2c: Support PN544 C3 secure firmware downloadArron Wang2014-02-161-6/+174
| | | | | | | | | PN544 C3 firmwares already contain the command frames to be sent, but as they may exceed the i2c maximum payload, we need to fragment them into secure chunks and send them through the secure write command. Signed-off-by: Arron Wang <arron.wang@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-27 09:25:56 +0100