| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit abebfbe2f731 ("dm: add ->flush() dax operation support") is
buggy. A DM device may be composed of multiple underlying devices and
all of them need to be flushed. That commit just routes the flush
request to the first device and ignores the other devices.
It could be fixed by adding more complex logic to the device mapper. But
there is only one implementation of the method pmem_dax_ops->flush - that
is pmem_dax_flush() - and it calls arch_wb_cache_pmem(). Consequently, we
don't need the pmem_dax_ops->flush abstraction at all, we can call
arch_wb_cache_pmem() directly from dax_flush() because dax_dev->ops->flush
can't ever reach anything different from arch_wb_cache_pmem().
It should be also pointed out that for some uses of persistent memory it
is needed to flush only a very small amount of data (such as 1 cacheline),
and it would be overkill if we go through that device mapper machinery for
a single flushed cache line.
Fix this by removing the pmem_dax_ops->flush abstraction and call
arch_wb_cache_pmem() directly from dax_flush(). Also, remove the device
mapper code that forwards the flushes.
Fixes: abebfbe2f731 ("dm: add ->flush() dax operation support")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm from Dan Williams:
"A rework of media error handling in the BTT driver and other updates.
It has appeared in a few -next releases and collected some late-
breaking build-error and warning fixups as a result.
Summary:
- Media error handling support in the Block Translation Table (BTT)
driver is reworked to address sleeping-while-atomic locking and
memory-allocation-context conflicts.
- The dax_device lookup overhead for xfs and ext4 is moved out of the
iomap hot-path to a mount-time lookup.
- A new 'ecc_unit_size' sysfs attribute is added to advertise the
read-modify-write boundary property of a persistent memory range.
- Preparatory fix-ups for arm and powerpc pmem support are included
along with other miscellaneous fixes"
* tag 'libnvdimm-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (26 commits)
libnvdimm, btt: fix format string warnings
libnvdimm, btt: clean up warning and error messages
ext4: fix null pointer dereference on sbi
libnvdimm, nfit: move the check on nd_reserved2 to the endpoint
dax: fix FS_DAX=n BLOCK=y compilation
libnvdimm: fix integer overflow static analysis warning
libnvdimm, nd_blk: remove mmio_flush_range()
libnvdimm, btt: rework error clearing
libnvdimm: fix potential deadlock while clearing errors
libnvdimm, btt: cache sector_size in arena_info
libnvdimm, btt: ensure that flags were also unchanged during a map_read
libnvdimm, btt: refactor map entry operations with macros
libnvdimm, btt: fix a missed NVDIMM_IO_ATOMIC case in the write path
libnvdimm, nfit: export an 'ecc_unit_size' sysfs attribute
ext4: perform dax_device lookup at mount
ext2: perform dax_device lookup at mount
xfs: perform dax_device lookup at mount
dax: introduce a fs_dax_get_by_bdev() helper
libnvdimm, btt: check memory allocation failure
libnvdimm, label: fix index block size calculation
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix format warnings (seen on i386) in nvdimm/btt.c:
../drivers/nvdimm/btt.c: In function ‘btt_map_init’:
../drivers/nvdimm/btt.c:430:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘size_t’ [-Wformat=]
dev_WARN_ONCE(to_dev(arena), size < 512,
^
../drivers/nvdimm/btt.c: In function ‘btt_log_init’:
../drivers/nvdimm/btt.c:474:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘size_t’ [-Wformat=]
dev_WARN_ONCE(to_dev(arena), size < 512,
^
Fixes: 86652d2eb347 ("libnvdimm, btt: clean up warning and error messages")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Convert all WARN* style messages to dev_WARN, and for errors in the IO
paths, use dev_err_ratelimited. Also remove some BUG_ONs in the IO path
and replace them with the above - no need to crash the machine in case
of an unaligned IO.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Delay the check of nd_reserved2 to the actual endpoint (acpi_nfit_ctl)
that uses it, as a prevention of a potential double-fetch bug.
While examining the kernel source code, I found a dangerous operation that
could turn into a double-fetch situation (a race condition bug) where
the same userspace memory region are fetched twice into kernel with sanity
checks after the first fetch while missing checks after the second fetch.
In the case of _IOC_NR(ioctl_cmd) == ND_CMD_CALL:
1. The first fetch happens in line 935 copy_from_user(&pkg, p, sizeof(pkg)
2. subsequently `pkg.nd_reserved2` is asserted to be all zeroes
(line 984 to 986).
3. The second fetch happens in line 1022 copy_from_user(buf, p, buf_len)
4. Given that `p` can be fully controlled in userspace, an attacker can
race condition to override the header part of `p`, say,
`((struct nd_cmd_pkg *)p)->nd_reserved2` to arbitrary value
(say nine 0xFFFFFFFF for `nd_reserved2`) after the first fetch but before the
second fetch. The changed value will be copied to `buf`.
5. There is no checks on the second fetches until the use of it in
line 1034: nd_cmd_clear_to_send(nvdimm_bus, nvdimm, cmd, buf) and
line 1038: nd_desc->ndctl(nd_desc, nvdimm, cmd, buf, buf_len, &cmd_rc)
which means that the assumed relation, `p->nd_reserved2` are all zeroes might
not hold after the second fetch. And once the control goes to these functions
we lose the context to assert the assumed relation.
6. Based on my manual analysis, `p->nd_reserved2` is not used in function
`nd_cmd_clear_to_send` and potential implementations of `nd_desc->ndctl`
so there is no working exploit against it right now. However, this could
easily turns to an exploitable one if careless developers start to use
`p->nd_reserved2` later and assume that they are all zeroes.
Move the validation of the nd_reserved2 field to the ->ndctl()
implementation where it has a stable buffer to evaluate.
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Dan reports:
The patch 62232e45f4a2: "libnvdimm: control (ioctl) messages for
nvdimm_bus and nvdimm devices" from Jun 8, 2015, leads to the
following static checker warning:
drivers/nvdimm/bus.c:1018 __nd_ioctl()
warn: integer overflows 'buf_len'
From a casual review, this seems like it might be a real bug. On
the first iteration we load some data into in_env[]. On the second
iteration we read a use controlled "in_size" from nd_cmd_in_size().
It can go up to UINT_MAX - 1. A high number means we will fill the
whole in_env[] buffer. But we potentially keep looping and adding
more to in_len so now it can be any value.
It simple enough to change, but it feels weird that we keep looping
even though in_env is totally full. Shouldn't we just return an
error if we don't have space for desc->in_num.
We keep looping because the size of the total input is allowed to be
bigger than the 'envelope' which is a subset of the payload that tells
us how much data to expect. For safety explicitly check that buf_len
does not overflow which is what the checker flagged.
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4a2: "libnvdimm: control (ioctl) messages for nvdimm_bus..."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
mmio_flush_range() suffers from a lack of clearly-defined semantics,
and is somewhat ambiguous to port to other architectures where the
scope of the writeback implied by "flush" and ordering might matter,
but MMIO would tend to imply non-cacheable anyway. Per the rationale
in 67a3e8fe9015 ("nd_blk: change aperture mapping from WC to WB"), the
only existing use is actually to invalidate clean cache lines for
ARCH_MEMREMAP_PMEM type mappings *without* writeback. Since the recent
cleanup of the pmem API, that also now happens to be the exact purpose
of arch_invalidate_pmem(), which would be a far more well-defined tool
for the job.
Rather than risk potentially inconsistent implementations of
mmio_flush_range() for the sake of one callsite, streamline things by
removing it entirely and instead move the ARCH_MEMREMAP_PMEM related
definitions up to the libnvdimm level, so they can be shared by NFIT
as well. This allows NFIT to be enabled for arm64.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Clearing errors or badblocks during a BTT write requires sending an ACPI
DSM, which means potentially sleeping. Since a BTT IO happens in atomic
context (preemption disabled, spinlocks may be held), we cannot perform
error clearing in the course of an IO. Due to this error clearing for
BTT IOs has hitherto been disabled.
In this patch we move error clearing out of the atomic section, and thus
re-enable error clearing with BTTs. When we are about to add a block to
the free list, we check if it was previously marked as an error, and if
it was, we add it to the freelist, but also set a flag that says error
clearing will be required. We then drop the lane (ending the atomic
context), and send a zero buffer so that the error can be cleared. The
error flag in the free list is protected by the nd 'lane', and is set
only be a thread while it holds that lane. When the error is cleared,
the flag is cleared, but while holding a mutex for that freelist index.
When writing, we check for two things -
1/ If the freelist mutex is held or if the error flag is set. If so,
this is an error block that is being (or about to be) cleared.
2/ If the block is a known badblock based on nsio->bb
The second check is required because the BTT map error flag for a map
entry only gets set when an error LBA is read. If we write to a new
location that may not have the map error flag set, but still might be in
the region's badblock list, we can trigger an EIO on the write, which is
undesirable and completely avoidable.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With the ACPI NFIT 'DSM' methods, acpi can be called from IO paths.
Specifically, the DSM to clear media errors is called during writes, so
that we can provide a writes-fix-errors model.
However it is easy to imagine a scenario like:
-> write through the nvdimm driver
-> acpi allocation
-> writeback, causes more IO through the nvdimm driver
-> deadlock
Fix this by using memalloc_noio_{save,restore}, which sets the GFP_NOIO
flag for the current scope when issuing commands/IOs that are expected
to clear errors.
Cc: <linux-acpi@vger.kernel.org>
Cc: <linux-nvdimm@lists.01.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In preparation for the error clearing rework, add sector_size in the
arena_info struct.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In btt_map_read, we read the map twice to make sure that the map entry
didn't change after we added it to the read tracking table. In
anticipation of expanding the use of the error bit, also make sure that
the error and zero flags are constant across the two map reads.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add helpers for converting a raw map entry to just the block number, or
either of the 'e' or 'z' flags in preparation for actually using the
error flag to mark blocks with media errors.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The IO context conversion for rw_bytes missed a case in the BTT write
path (btt_map_write) which should've been marked as atomic.
In reality this should not cause a problem, because map writes are to
small for nsio_rw_bytes to attempt error clearing, but it should be
fixed for posterity.
Add a might_sleep() in the non-atomic section of nsio_rw_bytes so that
things like the nfit unit tests, which don't actually sleep, can catch
bugs like this.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Check memory allocation failures and return -ENOMEM in such cases, as
already done few lines below for another memory allocation.
This avoids NULL pointers dereference.
Cc: <stable@vger.kernel.org>
Fixes: 14e494542636 ("libnvdimm, btt: BTT updates for UEFI 2.7 format")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The old calculation assumed that the label space was 128k and the label
size is 128. With v1.2 labels where the label size is 256 this
calculation will return zero. We are saved by the fact that the
nsindex_size is always pre-initialized from a previous 128 byte
assumption and we are lucky that the index sizes turn out the same.
Fix this going forward in case we start encountering different
geometries of label areas besides 128k.
Since the label size can change from one call to the next, drop the
caching of nsindex_size.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Now that we properly advertise the supported pte, pmd, and pud sizes,
restrict the supported alignments that can be set on a namespace. This
assumes that userspace was not previously relying on the ability to set
odd alignments. At least ndctl only ever supported setting the namespace
alignment to 4K, 2M, or 1G.
Cc: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The alignment of a DAX and PFN regions dictates the page sizes that can
be used to map the region. Even if the hardware page sizes are known the
actual range of supported page sizes that can be used with DAX depends
on the kernel configuration. As a result it's best that the kernel
advertises the alignments that should be used with these region types.
This patch adds the 'supported_alignments' region attribute to expose
this information to userspace.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[djbw: integrate with nd_size_select_show() rename and other fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Prepare for other another consumer of this size selection scheme that is
not a 'sector size'.
Cc: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
It is useful to be able to know the position of a DIMM in an
interleave-set. Consider the case where the order of the DIMMs changes
causing a namespace to be invalidated because the interleave-set cookie no
longer matches. If the before and after state of each DIMM position is
known this state debugged by the system owner.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently libnvdimm uses HPAGE_SIZE as the default alignment for DAX and
PFN devices. HPAGE_SIZE is the default hugetlbfs page size and when
hugetlbfs is disabled it defaults to PAGE_SIZE. Given DAX has more
in common with THP than hugetlbfs we should proably be using
HPAGE_PMD_SIZE, but this is undefined when THP is disabled so lets just
give it a new name.
The other usage of HPAGE_SIZE in libnvdimm is when determining how large
the altmap should be. For the reasons mentioned above it doesn't really
make sense to use HPAGE_SIZE here either. PMD_SIZE seems to be safe to
use in generic code and it happens to match the vmemmap allocation block
on x86 and Power. It's still a hack, but it's a slightly nicer hack.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| | |
No functional change in this patch, just in preparation for
basing the inflight mechanism on the queue in question.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The .rw_page in struct block_device_operations is used by the swap
subsystem to read/write the page contents from/into the corresponding
swap slot in the swap device. To support the THP (Transparent Huge
Page) swap optimization, the .rw_page is enhanced to support to
read/write THP if possible.
Link: http://lkml.kernel.org/r/20170724051840.2309-6-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@intel.com> [for brd.c, zram_drv.c, pmem.c]
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
__add_badblock_range() does not account sector alignment when
it sets 'num_sectors'. Therefore, an ARS error record range
spanning across two sectors is set to a single sector length,
which leaves the 2nd sector unprotected.
Change __add_badblock_range() to set 'num_sectors' properly.
Cc: <stable@vger.kernel.org>
Fixes: 0caeef63e6d2 ("libnvdimm: Add a poison list and export badblocks")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull more block updates from Jens Axboe:
"This is a followup for block changes, that didn't make the initial
pull request. It's a bit of a mixed bag, this contains:
- A followup pull request from Sagi for NVMe. Outside of fixups for
NVMe, it also includes a series for ensuring that we properly
quiesce hardware queues when browsing live tags.
- Set of integrity fixes from Dmitry (mostly), fixing various issues
for folks using DIF/DIX.
- Fix for a bug introduced in cciss, with the req init changes. From
Christoph.
- Fix for a bug in BFQ, from Paolo.
- Two followup fixes for lightnvm/pblk from Javier.
- Depth fix from Ming for blk-mq-sched.
- Also from Ming, performance fix for mtip32xx that was introduced
with the dynamic initialization of commands"
* 'for-linus' of git://git.kernel.dk/linux-block: (44 commits)
block: call bio_uninit in bio_endio
nvmet: avoid unneeded assignment of submit_bio return value
nvme-pci: add module parameter for io queue depth
nvme-pci: compile warnings in nvme_alloc_host_mem()
nvmet_fc: Accept variable pad lengths on Create Association LS
nvme_fc/nvmet_fc: revise Create Association descriptor length
lightnvm: pblk: remove unnecessary checks
lightnvm: pblk: control I/O flow also on tear down
cciss: initialize struct scsi_req
null_blk: fix error flow for shared tags during module_init
block: Fix __blkdev_issue_zeroout loop
nvme-rdma: unconditionally recycle the request mr
nvme: split nvme_uninit_ctrl into stop and uninit
virtio_blk: quiesce/unquiesce live IO when entering PM states
mtip32xx: quiesce request queues to make sure no submissions are inflight
nbd: quiesce request queues to make sure no submissions are inflight
nvme: kick requeue list when requeueing a request instead of when starting the queues
nvme-pci: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-loop: quiesce/unquiesce admin_q instead of start/stop its hw queues
nvme-fc: quiesce/unquiesce admin_q instead of start/stop its hw queues
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently if some one try to advance bvec beyond it's size we simply
dump WARN_ONCE and continue to iterate beyond bvec array boundaries.
This simply means that we endup dereferencing/corrupting random memory
region.
Sane reaction would be to propagate error back to calling context
But bvec_iter_advance's calling context is not always good for error
handling. For safity reason let truncate iterator size to zero which
will break external iteration loop which prevent us from unpredictable
memory range corruption. And even it caller ignores an error, it will
corrupt it's own bvecs, not others.
This patch does:
- Return error back to caller with hope that it will react on this
- Truncate iterator size
Code was added long time ago here 4550dd6c, luckily no one hit it
in real life :)
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
[hch: switch to true/false returns instead of errno values]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently all integrity prep hooks are open-coded, and if prepare fails
we ignore it's code and fail bio with EIO. Let's return real error to
upper layer, so later caller may react accordingly.
In fact no one want to use bio_integrity_prep() w/o bio_integrity_enabled,
so it is reasonable to fold it in to one function.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
[hch: merged with the latest block tree,
return bool from bio_integrity_prep]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
| |\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"libnvdimm updates for the latest ACPI and UEFI specifications. This
pull request also includes new 'struct dax_operations' enabling to
undo the abuse of copy_user_nocache() for copy operations to pmem.
The dax work originally missed 4.12 to address concerns raised by Al.
Summary:
- Introduce the _flushcache() family of memory copy helpers and use
them for persistent memory write operations on x86. The
_flushcache() semantic indicates that the cache is either bypassed
for the copy operation (movnt) or any lines dirtied by the copy
operation are written back (clwb, clflushopt, or clflush).
- Extend dax_operations with ->copy_from_iter() and ->flush()
operations. These operations and other infrastructure updates allow
all persistent memory specific dax functionality to be pushed into
libnvdimm and the pmem driver directly. It also allows dax-specific
sysfs attributes to be linked to a host device, for example:
/sys/block/pmem0/dax/write_cache
- Add support for the new NVDIMM platform/firmware mechanisms
introduced in ACPI 6.2 and UEFI 2.7. This support includes the v1.2
namespace label format, extensions to the address-range-scrub
command set, new error injection commands, and a new BTT
(block-translation-table) layout. These updates support inter-OS
and pre-OS compatibility.
- Fix a longstanding memory corruption bug in nfit_test.
- Make the pmem and nvdimm-region 'badblocks' sysfs files poll(2)
capable.
- Miscellaneous fixes and small updates across libnvdimm and the nfit
driver.
Acknowledgements that came after the branch was pushed: commit
6aa734a2f38e ("libnvdimm, region, pmem: fix 'badblocks'
sysfs_get_dirent() reference lifetime") was reviewed by Toshi Kani
<toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (42 commits)
libnvdimm, namespace: record 'lbasize' for pmem namespaces
acpi/nfit: Issue Start ARS to retrieve existing records
libnvdimm: New ACPI 6.2 DSM functions
acpi, nfit: Show bus_dsm_mask in sysfs
libnvdimm, acpi, nfit: Add bus level dsm mask for pass thru.
acpi, nfit: Enable DSM pass thru for root functions.
libnvdimm: passthru functions clear to send
libnvdimm, btt: convert some info messages to warn/err
libnvdimm, region, pmem: fix 'badblocks' sysfs_get_dirent() reference lifetime
libnvdimm: fix the clear-error check in nsio_rw_bytes
libnvdimm, btt: fix btt_rw_page not returning errors
acpi, nfit: quiet invalid block-aperture-region warnings
libnvdimm, btt: BTT updates for UEFI 2.7 format
acpi, nfit: constify *_attribute_group
libnvdimm, pmem: disable dax flushing when pmem is fronting a volatile region
libnvdimm, pmem, dax: export a cache control attribute
dax: convert to bitmask for flags
dax: remove default copy_from_iter fallback
libnvdimm, nfit: enable support for volatile ranges
libnvdimm, pmem: fix persistence warning
...
|
| | |\ |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The pmem driver attaches to both persistent and volatile memory ranges
advertised by the ACPI NFIT. When the region is volatile it is redundant
to spend cycles flushing caches at fsync(). Check if the hosting region
is volatile and do not set dax_write_cache() if it is.
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The dax_flush() operation can be turned into a nop on platforms where
firmware arranges for cpu caches to be flushed on a power-fail event.
The ACPI 6.2 specification defines a mechanism for the platform to
indicate this capability so the kernel can select the proper default.
However, for other platforms, the administrator must toggle this setting
manually.
Given this flush setting is a dax-specific mechanism we advertise it
through a 'dax' attribute group hanging off a host device. For example,
a 'pmem0' block-device gets a 'dax' sysfs-subdirectory with a
'write_cache' attribute to control response to dax cache flush requests.
This is similar to the 'queue/write_cache' attribute that appears under
block devices.
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Allow volatile nfit ranges to participate in all the same infrastructure
provided for persistent memory regions. A resulting resulting namespace
device will still be called "pmem", but the parent region type will be
"nd_volatile". This is in preparation for disabling the dax ->flush()
operation in the pmem driver when it is hosted on a volatile range.
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The pmem driver assumes if platform firmware describes the memory
devices associated with a persistent memory range and
CONFIG_ARCH_HAS_PMEM_API=y that it has all the mechanism necessary to
flush data to a power-fail safe zone. We warn if the firmware does not
describe memory devices, but we also need to warn if the architecture
does not claim pmem support.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Now that all callers of the pmem api have been converted to dax helpers that
call back to the pmem driver, we can remove include/linux/pmem.h and
asm/pmem.h.
Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Kill this globally defined wrapper and move to libnvdimm so that we can
ultimately remove include/linux/pmem.h and asm/pmem.h.
Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With all handling of the CONFIG_ARCH_HAS_PMEM_API case being moved to
libnvdimm and the pmem driver directly we do not need to provide global
wrappers and fallbacks in the CONFIG_ARCH_HAS_PMEM_API=n case. The pmem
driver will simply not link to arch_wb_cache_pmem() in that case. Same
as before, pmem flushing is only defined for x86_64, via
clean_cache_range(), but it is straightforward to add other archs in the
future.
arch_wb_cache_pmem() is an exported function since the pmem module needs
to find it, but it is privately declared in drivers/nvdimm/pmem.h because
there are no consumers outside of the pmem driver.
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Filesystem-DAX flushes caches whenever it writes to the address returned
through dax_direct_access() and when writing back dirty radix entries.
That flushing is only required in the pmem case, so add a dax operation
to allow pmem to take this extra action, but skip it for other dax
capable devices that do not provide a flush routine.
An example for this differentiation might be a volatile ram disk where
there is no expectation of persistence. In fact the pmem driver itself might
front such an address range specified by the NFIT. So, this "no flush"
property might be something passed down by the bus / libnvdimm.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
operations
The pmem driver has a need to transfer data with a persistent memory
destination and be able to rely on the fact that the destination writes are not
cached. It is sufficient for the writes to be flushed to a cpu-store-buffer
(non-temporal / "movnt" in x86 terms), as we expect userspace to call fsync()
to ensure data-writes have reached a power-fail-safe zone in the platform. The
fsync() triggers a REQ_FUA or REQ_FLUSH to the pmem driver which will turn
around and fence previous writes with an "sfence".
Implement a __copy_from_user_inatomic_flushcache, memcpy_page_flushcache, and
memcpy_flushcache, that guarantee that the destination buffer is not dirty in
the cpu cache on completion. The new copy_from_iter_flushcache and sub-routines
will be used to replace the "pmem api" (include/linux/pmem.h +
arch/x86/include/asm/pmem.h). The availability of copy_from_iter_flushcache()
and memcpy_flushcache() are gated by the CONFIG_ARCH_HAS_UACCESS_FLUSHCACHE
config symbol, and fallback to copy_from_iter_nocache() and plain memcpy()
otherwise.
This is meant to satisfy the concern from Linus that if a driver wants to do
something beyond the normal nocache semantics it should be something private to
that driver [1], and Al's concern that anything uaccess related belongs with
the rest of the uaccess code [2].
The first consumer of this interface is a new 'copy_from_iter' dax operation so
that pmem can inject cache maintenance operations without imposing this
overhead on other dax-capable drivers.
[1]: https://lists.01.org/pipermail/linux-nvdimm/2017-January/008364.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2017-April/009942.html
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit f979b13c3cc5 "libnvdimm, label: honor the lba size specified in
v1.2 labels") neglected to update the 'lbasize' in the label when the
namespace sector_size attribute was written. We need this value in the
label for inter-OS / pre-OS compatibility.
Fixes: f979b13c3cc5 ("libnvdimm, label: honor the lba size specified in v1.2 labels")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Have dsm functions called via the pass thru mechanism also
be checked against clear to send.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Some critical messages such as IO errors, metadata failures were printed
with dev_info. Make them louder by upgrading them to dev_warn or
dev_error.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We need to hold a reference on the 'dirent' until we are sure there are
no more notifications that will be sent. As noted in the new comments we
take advantage of the fact that the references are taken and dropped
under device_lock() and that nd_device_notify() holds device_lock() over
new badblocks notifications. The notifications that happen when
badblocks are cleared only occur while the device is active.
Also take the opportunity to fix up the error messages to report the
user visible effect of a sysfs_get_dirent() failure.
Fixes: 975750a98c26 ("libnvdimm, pmem: Add sysfs notifications to badblocks")
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A leftover from the 'bandaid' fix that disabled BTT error clearing in
rw_bytes resulted in an incorrect check. After we converted these checks
over to use the NVDIMM_IO_ATOMIC flag, the ndns->claim check was both
redundant, and incorrect. Remove it.
Fixes: 3ae3d67ba705 ("libnvdimm: add an atomic vs process context flag to rw_bytes")
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
btt_rw_page was not propagating errors frm btt_do_bvec, resulting in any
IO errors via the rw_page path going unnoticed. the pmem driver recently
fixed this in e10624f pmem: fail io-requests to known bad blocks
but same problem in BTT went neglected.
Fixes: 5212e11fde4d ("nd_btt: atomic sector updates")
Cc: <stable@vger.kernel.org>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This state is already visible by userspace since the BLK region will not
be enabled, and it is otherwise benign as it usually indicates that the
DIMM is not configured.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The UEFI 2.7 specification defines an updated BTT metadata format,
bumping the revision to 2.0. Add support for the new format, while
retaining compatibility for the old 1.1 format.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Sysfs "badblocks" information may be updated during run-time that:
- MCE, SCI, and sysfs "scrub" may add new bad blocks
- Writes and ioctl() may clear bad blocks
Add support to send sysfs notifications to sysfs "badblocks" file
under region and pmem directories when their badblocks information
is re-evaluated (but is not necessarily changed) during run-time.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The rules for which version of the label specification are in effect at
any given point in time are as follows:
1/ If a DIMM has an existing / valid index block then the version
specified is used regardless if it is a previous version.
2/ By default when the kernel is initializing new index blocks the
latest specification version (v1.2 at time of writing) is used.
3/ An environment that wants to force create v1.1 label-sets must
arrange for userspace to disable all active regions / namespaces /
dimms and write a valid set of v1.1 index blocks to the dimms.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
