| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
System BIOS sometimes allocates extra bus space for hotplug-capable PCIe
root/downstream ports. This space is needed if the device plugged to the
port will have more hotplug-capable downstream ports. A good example of
this is Thunderbolt. Each Thunderbolt device contains a PCIe switch and
one or more hotplug-capable PCIe downstream ports where the daisy chain
can be extended.
Currently Linux only allocates minimal bus space to make sure all the
enumerated devices barely fit there. The BIOS reserved extra space is
not taken into consideration at all. Because of this we run out of bus
space pretty quickly when more PCIe devices are attached to hotplug
downstream ports in order to extend the chain.
Modify the PCI core so we distribute the available BIOS allocated bus space
equally between hotplug-capable bridges to make sure there is enough bus
space for extending the hierarchy later on.
Update kernel docs of the affected functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
One can ask more buses to be reserved for hotplug bridges by passing
pci=hpbussize=N in the kernel command line. If the parent bus does not
have enough bus space available we incorrectly create child bus with the
requested number of subordinate buses.
In the example below hpbussize is set to one more than we have available
buses in the root port:
pci 0000:07:00.0: [8086:1578] type 01 class 0x060400
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:07:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:08: busn_res: can not insert [bus 08-ff] under [bus 07-3f] (conflicts with (null) [bus 07-3f])
pci_bus 0000:08: scanning bus
...
pci_bus 0000:0a: bus scan returning with max=40
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 40
pci_bus 0000:0a: [bus 0a-40] partially hidden behind bridge 0000:07 [bus 07-3f]
pci_bus 0000:08: bus scan returning with max=40
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 40
Instead of allowing this, limit the subordinate number to be less than or
equal the maximum subordinate number allocated for the parent bus (if it
has any).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove irrelevant dmesg messages]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The current scanning code is really hard to understand because it calls
the same function in a loop where pass value is changed without any
comments explaining it:
for (pass = 0; pass < 2; pass++)
for_each_pci_bridge(dev, bus)
max = pci_scan_bridge(bus, dev, max, pass);
Unfamiliar reader cannot tell easily what is the purpose of this loop
without looking at internals of pci_scan_bridge().
In order to make this bit easier to understand, open-code the loop in
pci_scan_child_bus() and pci_hp_add_bridge() with added comments.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
| |
There is not much point of having a file with a single function in it.
Instead we can just move pci_hp_add_bridge() to drivers/pci/probe.c and
make it available always when PCI core is enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: convert printk to dev_err()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following pattern is often used:
list_for_each_entry(dev, &bus->devices, bus_list) {
if (pci_is_bridge(dev)) {
...
}
}
Add a for_each_pci_bridge() helper to make that code easier to write and
read by reducing indentation level. It also saves one or few lines of code
in each occurrence.
Convert PCI core parts here at the same time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: fold in http://lkml.kernel.org/r/20171013165352.25550-1-andriy.shevchenko@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* pci/resource:
microblaze/PCI: Remove pcibios_setup_bus_{self/devices} dead code
ARC: Remove empty kernel/pcibios.c
PCI: Add a generic weak pcibios_align_resource()
PCI: Add a generic weak pcibios_fixup_bus()
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Multiple architectures define this as an empty function, and I'm adding
another one as part of the RISC-V port. Add a __weak version of
pcibios_fixup_bus() and delete the now-obselete ones in a handful of
ports.
The only functional change should be that microblaze used to export
pcibios_fixup_bus(). None of the other architectures exports this, so I
just dropped it.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add a print statement in pci_bus_wait_crs() so that user observes the
progress of device polling instead of silently waiting for timeout to be
reached.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: check for timeout first so we don't print "waiting, giving up",
always print time we've slept (not the actual timeout, print a "ready"
message if we've printed a "waiting" message]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Configuration Request Retry Status (CRS) was previously hidden inside
pci_bus_read_dev_vendor_id(). We want to add support for CRS in other
situations, such as waiting for a device to become ready after a Function
Level Reset.
Move CRS handling into pci_bus_wait_crs() so it can be called from other
places.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: pass pointer, not value, to pci_bus_wait_crs() so caller gets
correct Vendor ID]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add pci_bus_crs_vendor_id() to determine whether data returned for a config
read of the Vendor ID indicates a Configuration Request Retry Status (CRS)
response.
Per PCIe r3.1, sec 2.3.2, this data is only returned if:
- CRS Software Visibility is enabled,
- a config read includes both bytes of the Vendor ID, and
- the read receives a CRS completion
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, change name to pci_bus_crs_vendor_id(), make static
in probe.c, use it in pci_bus_read_dev_vendor_id()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
While waiting for a device to become ready (i.e., to return a non-CRS
completion to a read of its Vendor ID), if we got a valid response to the
very last read before timing out, we printed a warning and gave up on the
device even though it was actually ready.
For a typical 60s timeout, we wait about 65s (it's not exact because of the
exponential backoff), but we treated devices that became ready between 33s
and 65s as though they failed.
Move the Device ID read later so we check whether the device is ready
before checking for a timeout.
Thanks to Sinan Kaya <okaya@codeaurora.org>, reorder reads so we always
check device presence after sleep, since it's pointless to sleep unless we
recheck afterwards.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8cc9 ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* pci/irq-fixups:
arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()
PCI: xilinx-nwl: Move to struct pci_host_bridge IRQ mapping functions
PCI: rockchip: Move to struct pci_host_bridge IRQ mapping functions
PCI: xgene: Move to struct pci_host_bridge IRQ mapping functions
PCI: altera: Drop pci_fixup_irqs()
PCI: versatile: Drop pci_fixup_irqs()
PCI: generic: Drop pci_fixup_irqs()
PCI: faraday: Drop pci_fixup_irqs()
PCI: designware: Drop pci_fixup_irqs()
PCI: iproc: Drop pci_fixup_irqs()
PCI: rcar: Drop pci_fixup_irqs()
PCI: xilinx: Drop pci_fixup_irqs()
PCI: tegra: Drop pci_fixup_irqs()
ARM/PCI: Remove pci_fixup_irqs() call for bios32 host controllers
PCI: Add a call to pci_assign_irq() in pci_device_probe()
OF/PCI: Update of_irq_parse_and_map_pci() comment
PCI: Add pci_assign_irq() function and have pci_fixup_irqs() use it
PCI: Add IRQ mapping function pointers to pci_host_bridge struct
PCI: Build setup-irq.o on all arches
PCI: Remove pci_scan_root_bus_msi()
PCI: xilinx-nwl: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rockchip: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: generic: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xgene: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xilinx: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: altera: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: versatile: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: iproc: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rcar: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: aardvark: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: designware: Convert PCI scan API to pci_scan_root_bus_bridge()
ARM/PCI: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: Make pci_register_host_bridge() PCI core internal
PCI: Add pci_scan_root_bus_bridge() interface
PCI: tegra: Fix host bridge memory leakage
PCI: faraday: Fix host bridge memory leakage
PCI: Add devm_pci_alloc_host_bridge() interface
PCI: Add pci_free_host_bridge() interface
PCI: Initialize bridge release function at bridge allocation
PCI: faraday: Convert IRQ masking to raw PCI config accessors
PCI: iproc: Convert link check to raw PCI config accessors
PCI: xilinx-nwl: Remove nwl_pcie_enable_msi() unused bus parameter
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The pci_scan_root_bus_bridge() function allows passing a parameterized
struct pci_host_bridge and scanning the resulting PCI bus; since the struct
msi_controller is part of the struct pci_host_bridge and the struct
pci_host_bridge can now be passed to pci_scan_root_bus_bridge() explicitly,
there is no need for a scan interface with a MSI controller parameter.
With all PCI host controller drivers and platform code relying on
pci_scan_root_bus_msi() converted over to pci_scan_root_bus_bridge() the
pci_scan_root_bus_msi() becomes obsolete and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
With the introduction of pci_scan_root_bus_bridge() there is no need to
export pci_register_host_bridge() to other kernel subsystems other than the
PCI compilation unit that needs it.
Make pci_register_host_bridge() static to its compilation unit and convert
the existing drivers usage over to pci_scan_root_bus_bridge().
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The current pci_scan_root_bus() interface is made up of two main code
paths:
- pci_create_root_bus()
- pci_scan_child_bus()
pci_create_root_bus() is a wrapper function that allows to create a struct
pci_host_bridge structure, initialize it with the passed parameters and
register it with the kernel.
As the struct pci_host_bridge require additional struct members,
pci_create_root_bus() parameters list has grown in time, making it unwieldy
to add further parameters to it in case the struct pci_host_bridge gains
more members fields to augment its functionality.
Since PCI core code provides functions to allocate struct pci_host_bridge,
instead of forcing the pci_create_root_bus() interface to add new
parameters to cater for new struct pci_host_bridge functionality, it is
more suitable to add an interface in PCI core code to scan a PCI bus
straight from a struct pci_host_bridge created and customized by each
specific PCI host controller driver.
Add a pci_scan_root_bus_bridge() function to allow PCI host controller
drivers to create and initialize struct pci_host_bridge and scan the
resulting bus.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Struct pci_host_bridge can be allocated by PCI host bridge drivers which
usually allocate and map memory through devm managed interfaces.
Add a devm version for the pci_alloc_host_bridge() interface to simplify
PCI host controller driver porting and simplify the driver failure paths.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit a52d1443bba1 ("PCI: Export host bridge registration interface")
exported the pci_alloc_host_bridge() interface so that PCI host controllers
drivers can make use of it.
Introduce pci_alloc_host_bridge() kernel counterpart to free the host
bridge data structures, pci_free_host_bridge(), export it and update kernel
functions releasing host bridge objects allocated memory to make use of it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The introduction of pci_register_host_bridge() kernel interface allows PCI
host controller drivers to create the struct pci_host_bridge object,
initialize it and register it with the kernel so that its corresponding PCI
bus can be scanned and its devices probed.
The host bridge device release function pci_release_host_bridge_dev() is a
static function common for all struct pci_host_bridge allocated objects, so
in its current form cannot be used by PCI host bridge controllers drivers
to initialize the allocated struct pci_host_bridge, which leaves struct
pci_host_bridge devices release function uninitialized.
Since pci_release_host_bridge_dev() is a function common to all PCI host
bridge objects, initialize it in pci_alloc_host_bridge() (ie common host
bridge allocation interface) so that all struct pci_host_bridge objects
have their release function initialized by default at allocation time,
removing the need for exporting the common pci_release_host_bridge_dev()
function to other compilation units.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
John reported that an Intel QuickAssist crypto accelerator didn't work in a
Dell PowerEdge R730. The problem seems to be that we enabled ECRC when the
device doesn't support it:
85:00.0 Co-processor [0b40]: Intel Corporation DH895XCC Series QAT [8086:0435]
Capabilities: [100 v1] Advanced Error Reporting
AERCap: First Error Pointer: 00, GenCap- CGenEn+ ChkCap- ChkEn+
1302fcf0d03e ("PCI: Configure *all* devices, not just hot-added ones")
exposed the problem because it applies settings from the _HPX method to all
devices, not just hot-added ones. The R730 supplies an _HPX method that
allows the kernel to enable ECRC.
Only enable ECRC if the device advertises support for it.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1571798
Fixes: 1302fcf0d03e ("PCI: Configure *all* devices, not just hot-added ones")
Reported-by: John Mazzie <john_mazzie@dell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The test for INTx masking via PCI_COMMAND_INTX_DISABLE performed in
pci_intx_mask_supported() should be done before the device can be used.
This is to avoid writing PCI_COMMAND while the driver owns the device, in
case that has any effect on MSI/MSI-X interrupts.
Move the content of pci_intx_mask_supported() to pci_intx_mask_broken() and
call it from pci_setup_device().
The test result can be queried at any time later using the same
pci_intx_mask_supported() interface as before (though with changed
implementation), so callers (uio, vfio) should be unaffected.
Signed-off-by: Piotr Gregor <piotrgregor@rsyncme.org>
[bhelgaas: changelog, remove quirk check, remove locking, move
dev->broken_intx_masking assignment to caller]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
devices
Configuring DMA ops at probe time will allow deferring device probe when
the IOMMU isn't available yet. The dma_configure for the device is
now called from the generic device_attach callback just before the
bus/driver probe is called. This way, configuring the DMA ops for the
device would be called at the same place for all bus_types, hence the
deferred probing mechanism should work for all buses as well.
pci_bus_add_devices (platform/amba)(_device_create/driver_register)
| |
pci_bus_add_device (device_add/driver_register)
| |
device_attach device_initial_probe
| |
__device_attach_driver __device_attach_driver
|
driver_probe_device
|
really_probe
|
dma_configure
Similarly on the device/driver_unregister path __device_release_driver is
called which inturn calls dma_deconfigure.
This patch changes the dma ops configuration to probe time for
both OF and ACPI based platform/amba/pci bus devices.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci part)
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* pci/resource:
PCI: Don't resize resources when realigning all devices in system
PCI: Don't reassign resources that are already aligned
PCI: Factor pci_reassigndev_resource_alignment()
powerpc/powernv: Override pcibios_default_alignment() to force PCI devices to be page aligned
PCI: Add pcibios_default_alignment() for arch-specific alignment control
PCI: Fix calculation of bridge window's size and alignment
PCI: Ignore requested alignment for IOV BARs
PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A 64-bit value is not needed since a PCI ROM address consists in 32 bits.
This fixes a clang warning about "implicit conversion from 'unsigned long'
to 'u32'".
Also remove now unnecessary casts to u32 from __pci_read_base() and
pci_std_update_resource().
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Local variables 'l' and 'sz' are uninitialized. Normally, they would
be initialized by pci_read_config_dword() but when an error occurs,
some drivers immediately return an error code, which leaves the
argument uninitialized.
Provide a safe initial value to make the code more robust.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Detect on probe whether a PCI device is part of a Thunderbolt controller.
Intel uses a Vendor-Specific Extended Capability (VSEC) with ID 0x1234
on such devices. Detect presence of this VSEC and cache it in a newly
added is_thunderbolt bit in struct pci_dev.
Also, add a helper to check whether a given PCI device is situated on a
Thunderbolt daisy chain (i.e., below a PCI device with is_thunderbolt
set).
The necessity arises from the following:
* If an external Thunderbolt GPU is connected to a dual GPU laptop,
that GPU is currently registered with vga_switcheroo even though it
can neither drive the laptop's panel nor be powered off by the
platform. To vga_switcheroo it will appear as if two discrete
GPUs are present. As a result, when the external GPU is runtime
suspended, vga_switcheroo will cut power to the internal discrete GPU
which may not be runtime suspended at all at this moment. The
solution is to not register external GPUs with vga_switcheroo, which
necessitates a way to recognize if they're on a Thunderbolt daisy
chain.
* Dual GPU MacBook Pros introduced 2011+ can no longer switch external
DisplayPort ports between GPUs. (They're no longer just used for DP
but have become combined DP/Thunderbolt ports.) The driver to switch
the ports, drivers/platform/x86/apple-gmux.c, needs to detect presence
of a Thunderbolt controller and, if found, keep external ports
permanently switched to the discrete GPU.
v2: Make kerneldoc for pci_is_thunderbolt_attached() more precise,
drop portion of commit message pertaining to separate series.
(Bjorn Helgaas)
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Amir Levy <amir.jer.levy@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/0ab165a4a35c0b60f29d4c306c653ead14fcd8f9.1489145162.git.lukas@wunner.de
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Every PCIe device can generate 5-bit transaction Tags, which allow up to 32
concurrent requests. Some devices can generate 8-bit Extended Tags, which
allow up to 256 concurrent requests.
Per the ECN mentioned below, all PCIe Receivers are expected to support
Extended Tags, so devices are allowed (but not required) to enable them by
default.
If a device supports Extended Tags but does not enable them by default,
enable them. This allows the device to have up to 256 outstanding
transactions at a time, which may improve performance.
[bhelgaas: changelog, check for PCIe device]
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Extended_Tag_Enable_Default_05Sept2008_final.pdf
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A PCI-to-PCIe bridge (a "reverse bridge") has a PCI or PCI-X primary
interface and a PCI Express secondary interface. The PCIe interface is a
Downstream Port that originates a Link. See the "PCI Express to PCI/PCI-X
Bridge Specification", rev 1.0, sections 1.2 and A.6.
The bug report below involves a PCI-to-PCIe bridge and a PCIe switch below
the bridge:
00:1e.0 Intel 82801 PCI Bridge to [bus 01-0a]
01:00.0 Pericom PI7C9X111SL PCIe-to-PCI Reversible Bridge to [bus 02-0a]
02:00.0 Pericom Device 8608 [PCIe Upstream Port] to [bus 03-0a]
03:01.0 Pericom Device 8608 [PCIe Downstream Port] to [bus 0a]
01:00.0 is configured as a PCI-to-PCIe bridge (despite the name printed by
lspci). As we traverse a PCIe hierarchy, device connections alternate
between PCIe Links and internal Switch logic. Previously we did not
recognize that 01:00.0 had a secondary link, so we thought the 02:00.0
Upstream Port *did* have a secondary link. In fact, it's the other way
around: 01:00.0 has a secondary link, and 02:00.0 has internal Switch logic
on its secondary side.
When we thought 02:00.0 had a secondary link, the pci_scan_slot() ->
only_one_child() path assumed 02:00.0 could have only one child, so 03:00.0
was the only possible downstream device. But 03:00.0 doesn't exist, so we
didn't look for any other devices on bus 03.
Booting with "pci=pcie_scan_all" is a workaround, but we don't want users
to have to do that.
Recognize that PCI-to-PCIe bridges originate links on their secondary
interfaces.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189361
Fixes: d0751b98dfa3 ("PCI: Add dev->has_secondary_link to track downstream PCIe links")
Tested-by: Blake Moore <blake.moore@men.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.2+
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* pci/host-tegra:
arm64: tegra: Enable PCIe on Jetson TX1
arm64: tegra: Add PCIe host bridge on Tegra210
PCI: tegra: Enable the driver on 64-bit ARM
PCI: tegra: Add Tegra210 support
PCI: tegra: Implement PCA enable workaround
dt-bindings: pci: tegra: Add Tegra210 support
PCI: tegra: Use new pci_register_host_bridge() interface
PCI: Export host bridge registration interface
PCI: Allow driver-specific data in host bridge
PCI: Add pci_register_host_bridge() interface
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Allow PCI host bridge drivers to use the new host bridge interfaces to
register their host bridge.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Provide a way to allocate driver-specific data along with a PCI host bridge
structure. The bridge's ->private field points to this data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make the existing pci_host_bridge structure a proper device that is usable
by PCI host drivers in a more standard way. In addition to the existing
pci_scan_bus(), pci_scan_root_bus(), pci_scan_root_bus_msi(), and
pci_create_root_bus() interfaces, this unfortunately means having to add
yet another interface doing basically the same thing, and add some extra
code in the initial step.
However, this time it's more likely to be extensible enough that we won't
have to do another one again in the future, and we should be able to reduce
code much more as a result.
The main idea is to pull the allocation of 'struct pci_host_bridge' out of
the registration, and let individual host drivers and architecture code
fill the members before calling the registration function.
There are a number of things we can do based on this:
* Use a single memory allocation for the driver-specific structure
and the generic PCI host bridge
* consolidate the contents of driver-specific structures by moving
them into pci_host_bridge
* Add a consistent interface for removing a PCI host bridge again
when unloading a host driver module
* Replace the architecture specific __weak pcibios_*() functions with
callbacks in a pci_host_bridge device
* Move common boilerplate code from host drivers into the generic
function, based on contents of the structure
* Extend pci_host_bridge with additional members when needed without
having to add arguments to pci_scan_*().
* Move members of struct pci_bus into pci_host_bridge to avoid
having lots of identical copies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| | |
Remove the assumption that IORESOURCE_ROM_ENABLE == PCI_ROM_ADDRESS_ENABLE.
PCI_ROM_ADDRESS_ENABLE is the ROM enable bit defined by the PCI spec, so if
we're reading or writing a BAR register value, that's what we should use.
IORESOURCE_ROM_ENABLE is a corresponding bit in struct resource flags.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
|
| | | | |
| | \ | |
| |\ \ \
| | |/
| |/|
| | | |
'arm/exynos' into next
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
On DT based systems, the of_dma_configure() API implements DMA
configuration for a given device. On ACPI systems an API equivalent to
of_dma_configure() is missing which implies that it is currently not
possible to set-up DMA operations for devices through the ACPI generic
kernel layer.
This patch fills the gap by introducing acpi_dma_configure/deconfigure()
calls that for now are just wrappers around arch_setup_dma_ops() and
arch_teardown_dma_ops() and also updates ACPI and PCI core code to use
the newly introduced acpi_dma_configure/acpi_dma_deconfigure functions.
Since acpi_dma_configure() is used to configure DMA operations, the
function initializes the dma/coherent_dma masks to sane default values
if the current masks are uninitialized (also to keep the default values
consistent with DT systems) to make sure the device has a complete
default DMA set-up.
The DMA range size passed to arch_setup_dma_ops() is sized according
to the device coherent_dma_mask (starting at address 0x0), mirroring the
DT probing path behaviour when a dma-ranges property is not provided
for the device being probed; this changes the current arch_setup_dma_ops()
call parameters in the ACPI probing case, but since arch_setup_dma_ops()
is a NOP on all architectures but ARM/ARM64 this patch does not change
the current kernel behaviour on them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [pci]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Per PCIe spec r3.0, sec 2.3.1.1, the Read Completion Boundary (RCB)
determines the naturally aligned address boundaries on which a Read Request
may be serviced with multiple Completions:
- For a Root Complex, RCB is 64 bytes or 128 bytes
This value is reported in the Link Control Register
Note: Bridges and Endpoints may implement a corresponding command bit
which may be set by system software to indicate the RCB value for the
Root Complex, allowing the Bridge/Endpoint to optimize its behavior
when the Root Complex’s RCB is 128 bytes.
- For all other system elements, RCB is 128 bytes
Per sec 7.8.7, if a Root Port only supports a 64-byte RCB, the RCB of all
downstream devices must be clear, indicating an RCB of 64 bytes. If the
Root Port supports a 128-byte RCB, we may optionally set the RCB of
downstream devices so they know they can generate larger Completions.
Some BIOSes supply an _HPX that tells us to set RCB, even though the Root
Port doesn't have RCB set, which may lead to Malformed TLP errors if the
Endpoint generates completions larger than the Root Port can handle.
The IBM x3850 X6 with BIOS version -[A8E120CUS-1.30]- 08/22/2016 supplies
such an _HPX and a Mellanox MT27500 ConnectX-3 device fails to initialize:
mlx4_core 0000:41:00.0: command 0xfff timed out (go bit not cleared)
mlx4_core 0000:41:00.0: device is going to be reset
mlx4_core 0000:41:00.0: Failed to obtain HW semaphore, aborting
mlx4_core 0000:41:00.0: Fail to reset HCA
------------[ cut here ]------------
kernel BUG at drivers/net/ethernet/mellanox/mlx4/catas.c:193!
After 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration")
and 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices
with a link"), we apply _HPX settings to *all* devices, not just those
hot-added after boot.
Before 7a1562d4f2d0, we didn't touch the Mellanox RCB, and the device
worked. After 7a1562d4f2d0, we set its RCB to 128, and it failed.
Set the RCB to 128 iff the Root Port supports a 128-byte RCB. Otherwise,
set RCB to 64 bytes. This effectively ignores what _HPX tells us about
RCB.
Note that this change only affects _HPX handling. If we have no _HPX, this
does nothing with RCB.
[bhelgaas: changelog, clear RCB if not set for Root Port]
Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration")
Fixes: 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices with a link")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187781
Tested-by: Frank Danapfel <fdanapfe@redhat.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
CC: stable@vger.kernel.org # v3.18+
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* pci/aer:
PCI/AER: Fix aer_probe() kernel-doc comment
PCI/AER: Cache capability position
PCI/AER: Avoid memory allocation in interrupt handling path
ACPI / APEI: Send correct severity to calculate AER severity
PCI/AER: Remove duplicate AER severity translation
PCI/AER: Remove aerdriver.forceload kernel parameter
PCI/AER: Remove aerdriver.nosourceid kernel parameter
x86/PCI: VMD: Add quirk for AER to ignore source ID
PCI/AER: Add bus flag to skip source ID matching
Conflicts:
drivers/pci/probe.c
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Save the position of the error reporting capability so it doesn't need to
be rediscovered during error handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
| |
Add Precision Time Measurement (PTM) support (see PCIe r3.1, sec 6.22).
Enable PTM on PTM Root devices and switch ports. This does not enable PTM
on endpoints.
There currently are no PTM-capable devices on the market, but it is
expected to be supported by the Intel Apollo Lake platform.
[bhelgaas: complete rework]
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
'pci/pm' and 'pci/virtualization' into next
* pci/aspm:
PCI/ASPM: Remove redundant check of pcie_set_clkpm
* pci/dpc:
PCI: Remove DPC tristate module option
PCI: Bind DPC to Root Ports as well as Downstream Ports
PCI: Fix whitespace in struct dpc_dev
PCI: Convert Downstream Port Containment driver to use devm_* functions
* pci/hotplug:
PCI: Allow additional bus numbers for hotplug bridges
* pci/misc:
PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
PCI: Make bus_attr_resource_alignment static
MAINTAINERS: Add file patterns for PCI device tree bindings
PCI: Fix comment typo
* pci/msi:
PCI/MSI: irqchip: Fix PCI_MSI dependencies
* pci/pm:
PCI: pciehp: Ignore interrupts during D3cold
PCI: Document connection between pci_power_t and hardware PM capability
PCI: Add runtime PM support for PCIe ports
ACPI / hotplug / PCI: Runtime resume bridge before rescan
PCI: Power on bridges before scanning new devices
PCI: Put PCIe ports into D3 during suspend
PCI: Don't clear d3cold_allowed for PCIe ports
PCI / PM: Enforce type casting for pci_power_t
* pci/virtualization:
PCI: Add ACS quirk for Solarflare SFC9220
PCI: Add DMA alias quirk for Adaptec 3805
PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
PCI: Add function 1 DMA alias quirk for Marvell 88SE9182
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When a PCI device is removed through sysfs interface, the upstream bridge
(PCIe port) can be runtime suspended if it was the last device on that bus.
Now, if the bridge is in D3 we cannot find devices below the bridge
anymore. For example following fails to find the removed device again:
# echo 1 > /sys/bus/pci/devices/0000:00:01.0/0000:01:00.0/remove
# echo 1 > /sys/bus/pci/devices/0000:00:01.0/rescan
Where 0000:00:01.0 is the bridge device.
In order to be able to rescan devices below the bridge add
pm_runtime_get_sync()/pm_runtime_put() calls to pci_scan_bridge(). This
should keep bridges powered on while their children devices are being
scanned.
Reported-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
A user may hot add a switch requiring more than one bus to enumerate. This
previously required a system reboot if BIOS did not sufficiently pad the
bus resource, which they frequently don't do.
Add a kernel parameter so a user can specify the minimum number of bus
numbers to reserve for a hotplug bridge's subordinate buses so rebooting
won't be necessary.
The default is 1, which is equivalent to previous behavior.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
| |
Instead of assigning bus->domain_nr inside pci_bus_assign_domain_nr(),
return the domain and let the caller do the assignment. Rename
pci_bus_assign_domain_nr() to pci_bus_find_domain_nr() to reflect this.
No functional change intended.
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
