| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.3
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
The phy_ops variables are never modified after initialized in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
SATA_PLL_SOFT_RESET bit of CTRL_CORE_SMA_SW_0 must be toggled
between a SATA DPLL unlock and re-lock to prevent SATA lockup.
Introduce a new DT parameter 'syscon-pllreset' to provide the syscon
regmap access to this register which sits in the control module.
If the register is not provided we fallback to the old behaviour
i.e. SATA DPLL refclk will not be disabled and we prevent SoC low
power states.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Relying on PM-ops for shutting down PHY clocks was a
bad idea since the users (e.g. PCIe/SATA) might not
have been suspended by then.
The main culprit for not shutting down the clocks was
the stray pm_runtime_get() call in probe.
Fix the whole thing in the right way by getting rid
of that pm_runtime_get() call from probe and
removing all PM-ops. It is the sole responsibility
of the PHY user to properly turn OFF and de-initialize
the PHY as part of its suspend routine.
As PHY core serializes init/exit we don't need
to use a spinlock in this driver. So get rid of it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
New Features
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Remove extra space in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |/
|
|
|
|
|
|
| |
Code simplification. No functional change.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.
Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
we can't allow SATA DPLL to be in the unlocked state.
The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
This clock is being controlled only by the AHCI SATA driver and is
shut off during system suspend (if the SATA drive was not already attached)
causing the SATA DPLL to be unlocked and so causing errata i783.
To prevent sata_ref_clk from being disabled, we add the control of
this clock to the SATA PHY driver and prevent it from being disabled.
This also fixes the issue of SATA not working on OMAP5/DRA7 when
AHCI platform driver is built as a module.
NOTE: Device tree changes also required for OMAP5 & DRA7.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On system suspend, the runtime_suspend() driver hook doesn't get
called for USB phy and so the clocks are not disabled in the driver.
This causes the L3INIT_960M_GFCLK and L3INIT_480M_GFCLK to remain
active on the DRA7 platform while in system suspend.
In case of pcie-phy, the runtime_suspend hook gets called after
the suspend hook so we introduce a flag phy->enabled to keep
track if our clocks are enabled or not to prevent multiple
enable/disables.
Add suspend/resume hooks to the driver.
Move enabling/disabling clock code into helper functions.
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.
As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.
Hence phyid is no longer required.
So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.
Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.
This is needed to ensure Gen2 cards are enumerated consistently.
DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.
Test results on DRA74x and DRA72x EVMs:
Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.
DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/phy/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |/
|
|
|
|
|
|
|
| |
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
| |
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
| |
|
|
|
|
|
|
|
| |
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
|
| |
|
|
|
|
|
|
| |
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
|
| |
|
|
|
|
|
|
|
|
| |
Due to Errata i783, SATA breaks if its DPLL is idled. The recommeded
workaround to issue a softreset to the SATA controller doesn't seem to
work. Here we just prevent SATA DPLL from Idling and hence avoid
the issue altogether.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Limit .power_on() and .power_off() to just control the
PHY power and not the DPLL. The DPLL will be enabled
in .init() and idled in .exit().
Don't reprogram the DPLL if it has been already locked
by the bootloader. This fixes a problem with SATA, where
it fails if SATA was used by the bootloader.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
| |
SATA PHY doesn't need 'wkupclk; and 'refclk' so don't
try to get them for SATA PHY.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
| |
USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
| |
As this driver is no longer USB specific, use generic clock names.
- Fix PLL_SD_SHIFT from 9 to 10
- Don't separate prepare/unprepare clock from enable/disable. This
ensures optimal power savings.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
|
|
|
Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
