| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Only enable the SUSPEND IPA interrupt type when at least one
endpoint has that interrupt enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Keep track of which endpoints have the SUSPEND IPA interrupt enabled
in a variable-length bitmap. This will be used in the next patch to
allow the SUSPEND interrupt type to be disabled except when needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After a set of recent fixes the stmmac_phy_setup() and
stmmac_reinit_queues() methods have turned to having some duplicated code.
Let's get rid from the duplication by moving the MAC-capabilities
initialization to the PHYLINK MAC-capabilities getter. The getter is
called during each network device interface open/close cycle. So the
MAC-capabilities will be initialized in generic device open procedure and
in case of the Tx/Rx queues re-initialization as the original code
semantics implies.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since recent commits the stmmac_ops::phylink_get_caps() callback has no
longer been responsible for the phylink MAC capabilities getting, but
merely updates the MAC capabilities in the mac_device_info::link::caps
field. Rename the callback to comply with the what the method does now.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
packets
In the current mechanism of timestamping, am65-cpsw-nuss driver
enables hardware timestamping for all received packets by setting
the TSTAMP_EN bit in CPTS_CONTROL register, which directs the CPTS
module to timestamp all received packets, followed by passing
timestamp via DMA descriptors. This mechanism causes CPSW Port to
Lock up.
To prevent port lock up, don't enable rx packet timestamping by
setting TSTAMP_EN bit in CPTS_CONTROL register. The workaround for
timestamping received packets is to utilize the CPTS Event FIFO
that records timestamps corresponding to certain events. The CPTS
module is configured to generate timestamps for Multicast Ethernet,
UDP/IPv4 and UDP/IPv6 PTP packets.
Update supported hwtstamp_rx_filters values for CPSW's timestamping
capability.
Fixes: b1f66a5bee07 ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
CPTS FIFO
Add a new function "am65_cpts_rx_timestamp()" which checks for PTP
packets from header and timestamps them.
Add another function "am65_cpts_find_rx_ts()" which finds CPTS FIFO
Event to get the timestamp of received PTP packet.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The core_rmw() function calls core_read_mmd_indirect() to read the
requested register, and then calls core_write_mmd_indirect() to write the
requested value to the register. Because Clause 22 is used to access Clause
45 registers, some operations on core_write_mmd_indirect() are
unnecessarily run. Get rid of core_read_mmd_indirect() and
core_write_mmd_indirect(), and run only the necessary operations on
core_write() and core_rmw().
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Read the PHY address the switch listens on from the reg property of the
switch node on the device tree. This change brings support for MT7530
switches on boards with such bootstrapping configuration where the switch
listens on a different PHY address than the hardcoded PHY address on the
driver, 31.
As described on the "MT7621 Programming Guide v0.4" document, the MT7530
switch and its PHYs can be configured to listen on the range of 7-12,
15-20, 23-28, and 31 and 0-4 PHY addresses.
There are operations where the switch PHY registers are used. For the PHY
address of the control PHY, transform the MT753X_CTRL_PHY_ADDR constant
into a macro and use it. The PHY address for the control PHY is 0 when the
switch listens on 31. In any other case, it is one greater than the PHY
address the switch listens on.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240418161821.189263-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20240418161802.189247-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Only compile tested, no hardware available.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240418161751.189226-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure that the provided netdev name is not one of its aliases to
prevent unnecessary creation and destruction of the vport by
ovs-vswitchd.
Signed-off-by: Jun Gu <jun.gu@easystack.cn>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240419061425.132723-1-jun.gu@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The NLM_F_ACK flag is ignored for nfnetlink batch begin and end
messages. This is a problem for ynl which wants to receive an ack for
every message it sends, not just the commands in between the begin/end
messages.
Add processing for ACKs for begin/end messages and provide responses
when requested.
I have checked that iproute2, pyroute2 and systemd are unaffected by
this change since none of them use NLM_F_ACK for batch begin/end.
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-5-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a "--multi <do-op> <json>" command line to ynl that makes it
possible to add several operations to a single netlink request payload.
The --multi command line option is repeated for each operation.
This is used by the nftables family for transaction batches. For
example:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi batch-begin '{"res-id": 10}' \
--multi newtable '{"name": "test", "nfgen-family": 1}' \
--multi newchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--multi batch-end '{"res-id": 10}'
[None, None, None, None]
It can also be used for bundling get requests:
./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/nftables.yaml \
--multi gettable '{"name": "test", "nfgen-family": 1}' \
--multi getchain '{"name": "chain", "table": "test", "nfgen-family": 1}' \
--output-json
[{"name": "test", "use": 1, "handle": 1, "flags": [],
"nfgen-family": 1, "version": 0, "res-id": 2},
{"table": "test", "name": "chain", "handle": 1, "use": 0,
"nfgen-family": 1, "version": 0, "res-id": 2}]
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-4-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NetlinkProtocol.decode() was looking up ops by response value which breaks
when it is used for extack decoding of directional ops. Instead, pass
the op to decode().
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240418104737.77914-3-donald.hunter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
