| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 4e7e8017a80e1 (pinctrl: pinctrl-single:
enhance to configure multiple pins of different modules) improved
support for pinctrl-single,bits option, but also caused a regression
in parsing badly configured mask data.
If the masks in DT data are not quite right,
pcs_parse_bits_in_pinctrl_entry() can end up in an infinite loop,
trashing memory at the same time.
Add a check to verify that each loop actually removes bits from the
'mask', so that the loop can eventually end.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
pcs_enable() uses vals->mask instead of pcs->fmask when bits_per_mux is
enabled. However, pcs_disable() always uses pcs->fmask.
Fix pcs_disable() to use vals->mask with bits_per_mux.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On OMAPs the IO ring must be rearmed each time the pad wakeup
configuration is changed. So call pcs_soc->rearm() from
pcs_irq_set().
As pinctrl-single is now an interrupt controller in some cases,
we should follow the standards and keep the interrupts enabled
constantly, and not just for wake-up events. The tracking of
runtime vs wake-up interrupts can be handled separately for
the automated runtime PM solution when we have it in the
future.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: removed wrong comment, updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Looks like we need a little bit of arch specific handling
with the generic IRQ. Fix the issue with an ifdef the
same way as other drivers do.
ARM needs things set to IRQF_VALID, which also then sets
noprobe. Others seem to use just irq_set_noprobe().
Otherwise we can get:
drivers/pinctrl/pinctrl-single.c: In function 'pcs_irqdomain_map':
drivers/pinctrl/pinctrl-single.c:1750:2: error: implicit declaration of function 'set_irq_flags' [-Werror=implicit-function-declaration]
drivers/pinctrl/pinctrl-single.c:1750:21: error: 'IRQF_VALID' undeclared (first use in this function)
drivers/pinctrl/pinctrl-single.c:1750:34: error: 'IRQF_PROBE' undeclared (first use in this function)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For omaps, we still have dependencies to the legacy code
for handling the PRM (Power Reset Management) interrupts,
and also for reconfiguring the io wake-up chain after
changes.
Let's pass the PRM interrupt and the rearm functions via
auxdata. Then when at some point we have a proper PRM
driver, we can get the interrupt via device tree and
set up the rearm function as exported function in the
PRM driver.
By using auxdata we can remove a dependency to the
wake-up events for converting omap3 to be device
tree only.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The pin control registers can have interrupts for example
for device wake-up. These interrupts can be treated as a
chained interrupt controller as suggested earlier by
Linus Walleij <linus.walleij@linaro.org>.
This patch adds support for interrupts in a way that
should be pretty generic, and works for the omaps that
support wake-up interrupts. On omaps, there's an
interrupt enable and interrupt status bit for each pin.
The two pinctrl domains on omaps share a single interrupt
from the PRM chained interrupt handler. Support for
other similar hardware should be easy to add.
Note that this patch does not attempt to handle the
wake-up interrupts automatically unlike the earlier
patches. This patch allows the device drivers to do
a request_irq() on the wake-up pins as needed. I'll
try to do also a separate generic patch for handling
the wake-up events automatically.
Also note that as this patch makes the pinctrl-single
an irq controller, the current bindings need some
extra trickery to use interrupts from two different
interrupt controllers for the same driver. So it
might be worth waiting a little on the patches
enabling the wake-up interrupts from drivers as there
should be a generic way to handle it coming. And also
there's been discussion of interrupts-extended binding
for using interrupts from multiple interrupt controllers.
In any case, this patch should be ready to go allowing
handling the wake-up interrupts in a generic way, or
separately from the device drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-kernel@vger.kernel.org
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Let's replace is_pinconf with flags and add struct pcs_soc_data
so we can support SoC specific features like pin wake-up events.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This warning has been introduced by the commit
0f9bc4bcdf4f pinctrl: single: adopt pinctrl sleep mode management
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When setting pin configuration in the pinctrl framework, pin_config_set() or
pin_config_group_set() is called in a loop to set one configuration at a time
for the specified pin or group.
This patch 1) removes the loop and 2) changes the API to pass the whole pin
config array to the driver. It is now up to the driver to loop through the
configs. This allows the driver to potentially combine configs and reduce the
number of writes to pin config registers.
All c files changed have been build-tested to verify the change compiles and
that the corresponding .o is successfully generated.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
| |
Make pinctrl-single able to handle suspend/resume events and change
hogged pins states accordingly.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Take care to name pin names as
register-offset.bit-pos-of-pin-in-register in case configuring multiple
pins in register.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support to configure multiple pins in each register, existing
implementation added by [1] does not support full fledge multiple pin
configuration in single register, reports a pin clash when different
modules configure different bits of same register. The issue reported
and discussed here
http://www.spinics.net/lists/arm-kernel/msg235213.html
With pinctrl-single,bits-per-mux property specified, use function-mask
property to find out number pins to configure. Allocate and register
pin control functions based sub mask.
Tested on da850/omap-l138 EVM.
does not support variable submask for pins.
does not support pinconf.
[1] "pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux"
(9e605cb68a21d5704839a192a46ebcf387773704),
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Introduced by commit 9dddb4df90d136429b6d6ddefceb49a9b93f6cd1
(pinctrl: single: support generic pinconf)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
| |
pcs_pinconf_set() is always using "arg << shift" to configure two
parameters case. But pcs_add_conf2() didn't remove shift for config
argument. So correct it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If pcs->is_pinconf is false, it means does not support pinconf.
If pcs->is_pinconf is true, is_generic flag is always true.
This patch fixes below build error:
CC [M] drivers/pinctrl/pinctrl-single.o
drivers/pinctrl/pinctrl-single.c: In function 'pcs_probe':
drivers/pinctrl/pinctrl-single.c:1441:3: error: assignment of member 'is_generic' in read-only object
make[2]: *** [drivers/pinctrl/pinctrl-single.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
| |
Support the operation of generic pinconf. The supported config arguments
are INPUT_SCHMITT, INPUT_SCHMITT_ENABLE, DRIVE_STRENGHT, BIAS_DISABLE,
BIAS_PULLUP, BIAS_PULLDOWN, SLEW_RATE.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Since Hisilicon's pin controller is divided into two parts. One is the
function mux, and the other is pin configuration. These two parts are
in the different memory regions. So make pinctrl-single,function-mask
as optional property. Then we can define pingroups without valid
function mux that is only used for pin configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since gpio driver could create gpio range in DTS, it could invoke
pinctrl_request_gpio(). In the pinctrl-single driver, it needs to
configure pins with gpio function mode.
A new gpio function range should be created in DTS file in below.
pinctrl-single,gpio-range = <phandle pin_offset nr_pins gpio_func>;
range: gpio-range {
#pinctrl-single,gpio-range-cells = <3>;
};
The gpio-ranges property is used in gpio driver and the
pinctrl-single,gpio-range property is used in pinctrl-single driver.
1. gpio-ranges is used for gpio driver in below.
gpio-ranges = <phandle gpio_offset_in_chip pin_offset nr_pins>
gpio-ranges = < &pmx0 0 89 1 &pmx0 1 89 1 &pmx0 2 90 1
&pmx0 3 90 1 &pmx0 4 91 1 &pmx0 5 92 1>;
2. gpio driver could get pin offset from gpio-ranges property.
pinctrl-single driver could get gpio function mode from gpio_func
that is stored in @gpiofuncs list in struct pcs_device.
This new pinctrl-single,gpio-range is used as complement for
gpio-ranges property in gpio driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
| |
The pinconf, pinctrl and pinmux operation structures hold function
pointers that are never modified. Declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 2e8b2eab94c35d83bb7da71c63b4695f32ddca88.
Conflicts:
drivers/pinctrl/pinctrl-single.c
ERROR: "__aeabi_uldivmod" [drivers/pinctrl/pinctrl-single.ko]
undefined!]
On Fri, Jan 11, 2013 at 4:00 PM, Russell King wrote:
> The above error happens in builds including pinctrl-single - the
> reason
> is this, where resource_size_t may be 64-bit.
>
> gpio->range.pin_base = (r.start - pcs->res->start) /
> mux_bytes;
> gpio->range.npins = (r.end - r.start) / mux_bytes + 1;
The reason of not fixing this issue and reverting the patch instead is
this patch can't handle another case. It's not easy to handle multiple
gpios sharing one pin register. So this gpio range feature will be
implemented by other patches.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Barry Song <baohua.song@csr.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
*map should be tested for NULL instead of map.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Marvell's PXA/MMP silicon also match the behavior of pinctrl-single.
Each pin binds to one register. A lot of pins could be configured
as gpio.
GPIO range is defined as a child node of pinmux in .dtsi file. If those
pins are with the same gpio function configuration in the pinmux
register, they could be defined in the same GPIO range. For this new
child node, two properties are used.
reg = <the start of pinmux register in range, size of range>
pinctrl-single,gpio: <gpio base in range, the gpio function of the range
in the pinmux register>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
| |
Dump pinmux register value, not only function part in the pinmux
register.
Also fix the issue on caluclating pin offset. The last parameter
should be pin number, not register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
| |
Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:
pmx_dummy: pinmux@4a100040 {
compatible = "pinctrl-single";
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x00ff>;
};
&pmx_dummy {
pinctrl-names = "default";
pinctrl-0 = <&board_pins>;
board_pins: pinmux_board_pins {
pinctrl-single,pins = <
0x6c 0xf0f
0x6e 0x10f
0x70 0x23f
0x72 0xa5f
>;
};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
