| Commit message (Collapse) | Author | Files | Lines |
|---|
|
STag zero is a special STag that allows consumers to access any bus
address without registering memory. The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system). Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.
The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.
Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was a report of a data corruption
http://lkml.org/lkml/2008/11/14/121. There is a script included to
reproduce the problem.
During testing, I encountered a number of strange things with ext3, so I
tried ext2 to attempt to reduce complexity of the problem. I found that
fsstress would quickly hang in wait_on_inode, waiting for I_LOCK to be
cleared, even though instrumentation showed that unlock_new_inode had
already been called for that inode. This points to memory scribble, or
synchronisation problme.
i_state of I_NEW inodes is not protected by inode_lock because other
processes are not supposed to touch them until I_LOCK (and I_NEW) is
cleared. Adding WARN_ON(inode->i_state & I_NEW) to sites where we modify
i_state revealed that generic_sync_sb_inodes is picking up new inodes from
the inode lists and passing them to __writeback_single_inode without
waiting for I_NEW. Subsequently modifying i_state causes corruption. In
my case it would look like this:
CPU0 CPU1
unlock_new_inode() __sync_single_inode()
reg <- inode->i_state
reg -> reg & ~(I_LOCK|I_NEW) reg <- inode->i_state
reg -> inode->i_state reg -> reg | I_SYNC
reg -> inode->i_state
Non-atomic RMW on CPU1 overwrites CPU0 store and sets I_LOCK|I_NEW again.
Fix for this is rather than wait for I_NEW inodes, just skip over them:
inodes concurrently being created are not subject to data integrity
operations, and should not significantly contribute to dirty memory
either.
After this change, I'm unable to reproduce any of the added warnings or
hangs after ~1hour of running. Previously, the new warnings would start
immediately and hang would happen in under 5 minutes.
I'm also testing on ext3 now, and so far no problems there either. I
don't know whether this fixes the problem reported above, but it fixes a
real problem for me.
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Even when page reclaim is under mem_cgroup, # of scan page is determined by
status of global LRU. Fix that.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device. As a result, we end up with no backlight device at all.
We should instead disable it if there is an ACPI device, as the other
laptop drivers do. This regression was introduced in febf2d9 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").
Each laptop driver with backlight support got a similar change around
febf2d9. The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change. The regression is also in
2.6.28.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register. The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Unfortunately, Linux Foundation funding for my work on
man-pages/testing/doc under the auspices of the LF documentation
fellowship unfortunately ran out a short while ago (after earlier attempts
to seek funding, only Google stepped forward with a bit of further funding
for the position), so the patch below acknowledges something closer to
reality.
Unfortunately, there will (probably very) soon be a further downgrade from
"Maintained" to "Odd Fixes" or "Orphan", unless some funding miracle
occurs. So, if anyone is looking to become man-pages maintainer, there
may soon be an opening (okay, don't trample me in the rush ;-).)
Signed-off-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The 'battery remaining capacity' calculation in
drivers/power/ds2760_battery.c lacks a parameter check to a division
operation which causes the kernel to oops on my board.
[ 21.233750] Division by zero in kernel.
[ 21.237646] [<c002955c>] (__div0+0x0/0x20) from [<c012561c>] (Ldiv0+0x8/0x10)
[ 21.244816] [<c01bef34>] (ds2760_battery_read_status+0x0/0x2a4) from [<c01bf3a4>] (ds2760_battery_get_property+0x30/0xdc)
[ 21.255803] r8:c03a22c0 r7:c7886100 r6:00000009 r5:c782fe7c r4:c7886084
[ 21.262518] [<c01bf374>] (ds2760_battery_get_property+0x0/0xdc) from [<c01bde98>] (power_supply_show_property+0x48/0x114)
[ 21.273480] r6:c7996000 r5:00000009 r4:00000000
[ 21.278111] [<c01bde50>] (power_supply_show_property+0x0/0x114) from [<c01be158>] (power_supply_uevent+0x188/0x280)
[ 21.288537] r8:00000001 r7:c7886100 r6:c7996000 r5:000000b4 r4:00000000
[ 21.295222] [<c01bdfd0>] (power_supply_uevent+0x0/0x280) from [<c015c664>] (dev_uevent+0xd4/0x10c)
[ 21.304199] [<c015c590>] (dev_uevent+0x0/0x10c) from [<c0128440>] (kobject_uevent_env+0x180/0x390)
[ 21.313170] r5:00000000 r4:c78860ac
[ 21.316725] [<c01282c0>] (kobject_uevent_env+0x0/0x390) from [<c0128664>] (kobject_uevent+0x14/0x18)
[ 21.325850] [<c0128650>] (kobject_uevent+0x0/0x18) from [<c01bdc34>] (power_supply_changed_work+0x5c/0x70)
[ 21.335506] [<c01bdbd8>] (power_supply_changed_work+0x0/0x70) from [<c004d290>] (run_workqueue+0xbc/0x144)
[ 21.345167] r4:c7812040
[ 21.347716] [<c004d1d4>] (run_workqueue+0x0/0x144) from [<c004d94c>] (worker_thread+0xa8/0xbc)
[ 21.356296] r7:c7812040 r6:c7820b00 r5:c782ffa4 r4:c7812048
[ 21.361957] [<c004d8a4>] (worker_thread+0x0/0xbc) from [<c0051008>] (kthread+0x5c/0x94)
[ 21.369971] r7:00000000 r6:c004d8a4 r5:c7812040 r4:c782e000
[ 21.375612] [<c0050fac>] (kthread+0x0/0x94) from [<c00403d0>] (do_exit+0x0/0x688)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In sget(), destroy_super(s) is called with s->s_umount held, which makes
lockdep unhappy.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the second fasync_helper() fails, pipe_rdwr_fasync() returns the error
but leaves the file on ->fasync_readers.
This was always wrong, but since 233e70f4228e78eb2f80dc6650f65d3ae3dbf17c
"saner FASYNC handling on file close" we have the new problem. Because in
this case setfl() doesn't set FASYNC bit, __fput() will not do
->fasync(0), and we leak fasync_struct with ->fa_file pointing to the
freed file.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
W1 master implementations are expected to return 0 or 1 from their
read_bit() function. However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't. Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the following warning on x86_64:
LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux: 'memcpy' exported twice. Previous export was in vmlinux
For x86_64, this symbol is already exported from arch/um/sys-x86_64/ksyms.c.
Reported-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Tested-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is currently impossible to run a user-mode linux machine inside another
user-mode linux (UML on UML). It breaks after a few instructions. When
it tries to check whether SYSEMU is installed (the inner) UML receives an
inconsistent result (from the outer UML).
This is the output of a broken attempt:
$ ./linux mem=256m ubd0=cow
Locating the bottom of the address space ... 0x0
Locating the top of the address space ... 0xc0000000
Core dump limits :
soft - 0
hard - NONE
Checking that ptrace can change system call numbers...OK
Checking ptrace new tags for syscall emulation...unsupported
Checking syscall emulation patch for ptrace...check_sysemu : expected SIGTRAP, got status = 256
$
The problem is the following:
PTRACE_SYSCALL/SINGLESTEP is currently managed inside arch_ptrace for ARCH=um.
PTRACE_SYSEMU/SUSEMU_SINGLESTEP is not captured in arch_ptrace's switch,
therefore it is erroneously passed back to ptrace_request (in
kernel/ptrace).
This simple patch simply forces ptrace to return an error on
PTRACE_SYSEMU/SUSEMU_SINGLESTEP as it is unsupported on ARCH=um, and fixes
the problem.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Renzo Davoli <renzo@cs.unibo.it>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
"Enabling" should read "Disabling"
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Prakash's system needs MSI disabled on some bridges, but not all.
This seems to be the minimal fix for 2.6.29, but should be replaced
during 2.6.30.
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
The RPA PCI hotplug driver calls EEH routines, so should depend on
EEH. Also PPC_PSERIES implies PPC64, so remove that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.
Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.
The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.
Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
This patch is intended to disable L0s ASPM link state for 82598 (ixgbe)
parts due to the fact that it is possible to corrupt TX data when coming
back out of L0s on some systems. The workaround had been added for 82575
(igb) previously, but did not use the ASPM api. This quirk uses the ASPM
api to prevent the ASPM subsystem from re-enabling the L0s state.
Instead of adding the fix in igb to the ixgbe driver as well it was
decided to move it into a pci quirk. It is necessary to move the fix out
of the driver and into a pci quirk in order to prevent the issue from
occuring prior to driver load to handle the possibility of the device being
passed to a VM via direct assignment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Enable following features:
* MTD (PHYSMAP)
* LED (LEDS_GPIO)
* RBTX4939
* 7SEGLED
* IDE (IDE_TX4938, IDE_TX4939)
* SMC91X
* RTC_DRV_TX4939
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Current VR5500 processor support lacks of some functions which are
expected to be configured/synthesized on arch initialization.
Here're some VR5500A spec notes:
* All execution hazards are handled in hardware.
* Once VR5500A stops the operation of the pipeline by WAIT instruction,
it could return from the standby mode only when either a reset, NMI
request, or all enabled interrupts is/are detected. In other words,
if interrupts are disabled by Status.IE=0, it keeps in standby mode
even when interrupts are internally asserted.
Notes on WAIT: The operation of the processor is undefined if WAIT
insn is in the branch delay slot. The operation is also undefined
if WAIT insn is executed when Status.EXL and Status.ERL are set to 1.
* VR5500A core only implements the Load prefetch.
With these changes, it boots fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Xiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On swapon() path, it has already i_mutex. So, this uses i_alloc_sem
instead of it.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Laurent GUERBY <laurent@guerby.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.
fd.o bug #20567. Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Impact: work around boot crash
Work around Intel Atom erratum AAH41 (probabilistically) - it's triggering
in the field.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix kpf_copy_bit(src,dst) to be kpf_copy_bit(dst,src) to match the
actual call patterns, e.g. kpf_copy_bit(kflags, KPF_LOCKED, PG_locked).
This misplacement of src/dst only affected reporting of PG_writeback,
PG_reclaim and PG_buddy. For others kflags==uflags so not affected.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to check and report if there are no available fences - or else we
spin endlessly waiting for a buffer to magically unpin itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
As we may steal the fence register of an unpinned buffer for another,
every time we repin the buffer we need to recheck whether it needs to be
allocated a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
If we wait upon a request and successfully unbind a buffer occupying a
fence register, then that slot will be freed and cause a NULL derefrence
upon rescanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Comparing the layouts of struct detail_pixel_timing with
x.org's struct detailed_timings and how those are handled,
it appears that the hsync_positive and vsync_positive
fields are backwards.
This patch fixes https://bugs.freedesktop.org/show_bug.cgi?id=20019
for me. It was tested on 2 monitors, LG FLATRON L225WS 22" and
a YAKUMO 17" for which more details are unknown.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
radeonfb and aty128fb have a special hook called by the PowerMac platform
code very very early on resume from sleep to bring the screen back. This
is useful for debugging wakup problems, but unfortunately, this also became
a source of problems of its own.
The hook is called extremely early, with interrupts still off, and the code
path involved with that code nowadays rely on things like taking mutexes,
GFP_KERNEL allocations, etc...
In addition, the driver now relies on the PCI core to restore the standard
config space before calling resume which doesn't happen with this early
code path.
I'm keeping the code in but commented out along with a fixup call to
pci_restore_state(). The reason is that I still want to make it easy to
re-enable temporarily to track wake up problems, and it's possible that
I can revive it at some stage if we make sleeping things save to call
in early resume using a system state.
In the meantime, this should fix several reported regressions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The hvcs and hvsi backends both set tty->low_latency to one, along
with more or less scary comments regarding bugs or races that would
happen if not doing so.
However, they also both call tty_flip_buffer_push() in conexts where
it's illegal to do so since some recent tty changes (or at least it
may have been illegal always but it nows blows) when low_latency is
set (ie, hard interrupt or with spinlock held and irqs disabled).
This removes the setting for now to get them back to working condition,
we'll have to address the races described in the comments separately
if they are still an issue (some of this might have been fixed already).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Prevent the kernel from being crashed by a divide-by-zero operation when
supplied an incorrectly filled 'struct fb_var_screeninfo' from userland.
Previously i810_main.c:1005 (i810_check_params) was using the global
'yres' symbol previously defined at i810_main.c:145 as a module parameter
value holder (i810_main.c:2174). If i810fb is compiled-in or if this
param doesn't get a default value, this direct usage leads to a
divide-by-zero at i810_main.c:1005 (i810_check_params). The patch simply
replace the 'yres' global, perhaps undefined symbol usage by a given
parameter structure lookup.
This problem occurs with directfb, mplayer -vo fbdev, SDL library.
It was also reported ( but non solved ) at:
http://mail.directfb.org/pipermail/directfb-dev/2008-March/004050.html
Signed-off-by: Samuel CUELLA <samuel.cuella@supinfo.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There isn't any mcfqspi.h in the tree, and without it everything inside the
#ifdef CONFIG_SPI is uncompilable.
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the RCU documentation to call out the need for callers of
primitives like call_rcu() and synchronize_rcu() to prevent subsequent RCU
readers from hazard.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We were returning early in the sysfs directory cleanup function if the
user belonged to a non init usernamespace. Due to this a lot of the
cleanup was not done and we were left with a leak. Fix the leak.
Reported-by: Serge Hallyn <serue@linux.vnet.ibm.com>
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit e480814f138cd5d78a8efe397756ba6b6518fdb6 ("[MTD] [MAPS] physmap:
fix wrong free and del_mtd_{partition,device}") introduces a NULL pointer
dereference in physmap_flash_remove when called from the error path in
physmap_flash_probe (if map_probe failed).
Call del_mtd_{partition,device} only if info->cmtd was not NULL.
Reported-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When GTT size is equal to amount of video memory, the amount of GTT
entries is computed lower than zero, which is invalid and leads to
off-by-one error in intel_i915_configure()
Originally posted here:
http://bugzilla.kernel.org/show_bug.cgi?id=12539
http://bugzilla.redhat.com/show_bug.cgi?id=445592
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 771999b65f79264acde4b855e5d35696eca5e80c ("[MTD] DataFlash: bugfix,
binary page sizes now handled") broke support for probing AT45DB321C flash
chips. These chips do not support the "page size" status bit, so if we
match the JEDEC id return early.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a problem in the IDR system, where an idr_remove_all() hands a data
element to call_rcu() (via free_layer()) before making that data element
inaccessible to new readers. This is very bad, and results in readers
still having a reference to this data element at the end of the grace
period.
Tests on large machines that concurrently map and unmap user-space memory
within the same multithreaded process result in crashes within about five
minutes. Applying this patch increases the kernel's longevity to the
three-to-eight-hour range.
There appear to be other similar problems in idr_get_empty_slot() and
sub_remove(), but I fixed the easy one in idr_remove_all() first. It is
therefore no surprise that failures still occur.
Located-by: Milton Miller II <miltonm@austin.ibm.com>
Tested-by: Milton Miller II <miltonm@austin.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Very annoying when working with containters.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: fix bug to make agp work with dri
Jeffrey reported that dri does work with 64bit, but doesn't work with
32bit it turns out NB aperture is 32M, aperture on agp is 128M
64bit is using 64M for vaidation for 64 iommu/gart 32bit is only using
32M..., and will not update the nb aperture.
So try to compare nb apterture and agp apterture before leaving not
touch nb aperture.
Reported-by: Jeffrey Trull <jetrull@sbcglobal.net>
Tested-by: Jeffrey Trull <jetrull@sbcglobal.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* ->put_char changes
* HIGHMEM is bogus it seems, there is no kmap_atomic() et al
* some includes
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Chris Zankel <zankel@tensilica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The verstep check in the lm85 driver fails because the upper nibble of
the version register is 0x7, not 0x6, on the adt7468 chip. Probing of
all adt7468s was broken by 69fc1feba2d5856ff74dedb6ae9d8c490210825c
("hwmon: (lm85) Rework the device detection"), and this patch fixes
that. Also add in a missing i2c_device_id that accidentally got dropped
from the original patch.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED menu.
Fix by moving it to just after all of the EMBEDDED menu symbols. Also,
ANON_INODES has a similar problem, so move it to just above the EMBEDDED
menu items since it is used in the EMBEDDED menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
get_nid_for_pfn() returns int
Presumably the (nid < 0) case has never happened.
We do know that it is happening on one system while creating a symlink for
a memory section so it should also happen on the same system if
unregister_mem_sect_under_nodes() were called to remove the same symlink.
The test was actually added in response to a problem with an earlier
version reported by Yasunori Goto where one or more of the leading pages
of a memory section on the 2nd node of one of his systems was
uninitialized because I believe they coincided with a memory hole.
That earlier version did not ignore uninitialized pages and determined
the nid by considering only the 1st page of each memory section. This
caused the symlink to the 1st memory section on the 2nd node to be
incorrectly created in /sys/devices/system/node/node0 instead of
/sys/devices/system/node/node1. The problem was fixed by adding the
test to skip over uninitialized pages.
I suspect we have not seen any reports of the non-removal
of a symlink due to the incorrect declaration of the nid
variable in unregister_mem_sect_under_nodes() because
- systems where a memory section could have an uninitialized
range of leading pages are probably rare.
- memory remove is probably not done very frequently on the
systems that are capable of demonstrating the problem.
- lingering symlink(s) that should have been removed may
have simply gone unnoticed.
[garyhade@us.ibm.com: wrote changelog]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
