summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/libsas (follow)
Commit message (Collapse)AuthorAgeFilesLines
* ata: make SATA_PMP option selectable only if any SATA host driver is enabledBartlomiej Zolnierkiewicz2020-03-261-0/+1
| | | | | | | | | | | | | | | | There is no reason to expose SATA_PMP config option when no SATA host drivers are enabled. To fix it add SATA_HOST config option, make all SATA host drivers select it and finally make SATA_PMP config options depend on it. This also serves as preparation for the future changes which optimize libata core code size on PATA only setups. CC: "James E.J. Bottomley" <jejb@linux.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # for SCSI bits Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* scsi: libsas: Tidy SAS address print formatJohn Garry2019-12-217-11/+11
| | | | | | | | | | | | | | | | | | | | Currently we use a mixture of %016llx, %llx, and %16llx when printing a SAS address. Since the most significant nibble of the SAS address is always 5 - as per standard - this formatting is not so important; but some fake SAS addresses for SATA devices may not be. And we have mangled/invalid address to consider also. And it's better to be consistent in the code, so use a fixed format. The SAS address is a fixed size at 64b, so we want to 0 byte extend to 16 nibbles, so use %016llx globally. Also make some prints to be explicitly hex, and tidy some whitespace issue. Link: https://lore.kernel.org/r/1576758957-227350-1-git-send-email-john.garry@huawei.com Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: stop discovering if oob mode is disconnectedJason Yan2019-12-101-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The discovering of sas port is driven by workqueue in libsas. When libsas is processing port events or phy events in workqueue, new events may rise up and change the state of some structures such as asd_sas_phy. This may cause some problems such as follows: ==>thread 1 ==>thread 2 ==>phy up ==>phy_up_v3_hw() ==>oob_mode = SATA_OOB_MODE; ==>phy down quickly ==>hisi_sas_phy_down() ==>sas_ha->notify_phy_event() ==>sas_phy_disconnected() ==>oob_mode = OOB_NOT_CONNECTED ==>workqueue wakeup ==>sas_form_port() ==>sas_discover_domain() ==>sas_get_port_device() ==>oob_mode is OOB_NOT_CONNECTED and device is wrongly taken as expander This at last lead to the panic when libsas trying to issue a command to discover the device. [183047.614035] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [183047.622896] Mem abort info: [183047.625762] ESR = 0x96000004 [183047.628893] Exception class = DABT (current EL), IL = 32 bits [183047.634888] SET = 0, FnV = 0 [183047.638015] EA = 0, S1PTW = 0 [183047.641232] Data abort info: [183047.644189] ISV = 0, ISS = 0x00000004 [183047.648100] CM = 0, WnR = 0 [183047.651145] user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000b7df67be [183047.657834] [0000000000000058] pgd=0000000000000000 [183047.662789] Internal error: Oops: 96000004 [#1] SMP [183047.667740] Process kworker/u16:2 (pid: 31291, stack limit = 0x00000000417c4974) [183047.675208] CPU: 0 PID: 3291 Comm: kworker/u16:2 Tainted: G W OE 4.19.36-vhulk1907.1.0.h410.eulerosv2r8.aarch64 #1 [183047.687015] Hardware name: N/A N/A/Kunpeng Desktop Board D920S10, BIOS 0.15 10/22/2019 [183047.695007] Workqueue: 0000:74:02.0_disco_q sas_discover_domain [183047.700999] pstate: 20c00009 (nzCv daif +PAN +UAO) [183047.705864] pc : prep_ata_v3_hw+0xf8/0x230 [hisi_sas_v3_hw] [183047.711510] lr : prep_ata_v3_hw+0xb0/0x230 [hisi_sas_v3_hw] [183047.717153] sp : ffff00000f28ba60 [183047.720541] x29: ffff00000f28ba60 x28: ffff8026852d7228 [183047.725925] x27: ffff8027dba3e0a8 x26: ffff8027c05fc200 [183047.731310] x25: 0000000000000000 x24: ffff8026bafa8dc0 [183047.736695] x23: ffff8027c05fc218 x22: ffff8026852d7228 [183047.742079] x21: ffff80007c2f2940 x20: ffff8027c05fc200 [183047.747464] x19: 0000000000f80800 x18: 0000000000000010 [183047.752848] x17: 0000000000000000 x16: 0000000000000000 [183047.758232] x15: ffff000089a5a4ff x14: 0000000000000005 [183047.763617] x13: ffff000009a5a50e x12: ffff8026bafa1e20 [183047.769001] x11: ffff0000087453b8 x10: ffff00000f28b870 [183047.774385] x9 : 0000000000000000 x8 : ffff80007e58f9b0 [183047.779770] x7 : 0000000000000000 x6 : 000000000000003f [183047.785154] x5 : 0000000000000040 x4 : ffffffffffffffe0 [183047.790538] x3 : 00000000000000f8 x2 : 0000000002000007 [183047.795922] x1 : 0000000000000008 x0 : 0000000000000000 [183047.801307] Call trace: [183047.803827] prep_ata_v3_hw+0xf8/0x230 [hisi_sas_v3_hw] [183047.809127] hisi_sas_task_prep+0x750/0x888 [hisi_sas_main] [183047.814773] hisi_sas_task_exec.isra.7+0x88/0x1f0 [hisi_sas_main] [183047.820939] hisi_sas_queue_command+0x28/0x38 [hisi_sas_main] [183047.826757] smp_execute_task_sg+0xec/0x218 [183047.831013] smp_execute_task+0x74/0xa0 [183047.834921] sas_discover_expander.part.7+0x9c/0x5f8 [183047.839959] sas_discover_root_expander+0x90/0x160 [183047.844822] sas_discover_domain+0x1b8/0x1e8 [183047.849164] process_one_work+0x1b4/0x3f8 [183047.853246] worker_thread+0x54/0x470 [183047.856981] kthread+0x134/0x138 [183047.860283] ret_from_fork+0x10/0x18 [183047.863931] Code: f9407a80 528000e2 39409281 72a04002 (b9405800) [183047.870097] kernel fault(0x1) notification starting on CPU 0 [183047.875828] kernel fault(0x1) notification finished on CPU 0 [183047.881559] Modules linked in: unibsp(OE) hns3(OE) hclge(OE) hnae3(OE) mem_drv(OE) hisi_sas_v3_hw(OE) hisi_sas_main(OE) [183047.892418] ---[ end trace 4cc26083fc11b783 ]--- [183047.897107] Kernel panic - not syncing: Fatal exception [183047.902403] kernel fault(0x5) notification starting on CPU 0 [183047.908134] kernel fault(0x5) notification finished on CPU 0 [183047.913865] SMP: stopping secondary CPUs [183047.917861] Kernel Offset: disabled [183047.921422] CPU features: 0x2,a2a00a38 [183047.925243] Memory Limit: none [183047.928372] kernel reboot(0x2) notification starting on CPU 0 [183047.934190] kernel reboot(0x2) notification finished on CPU 0 [183047.940008] ---[ end Kernel panic - not syncing: Fatal exception ]--- Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com Reported-by: Gao Chuan <gaochuan4@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: sas_discover: Mark expected switch fall-throughGustavo A. R. Silva2019-08-211-0/+1
| | | | | | | | | | | | | | | | | | | Mark switch cases where we are expecting to fall through. Fix the following warning (Building: mtx1_defconfig mips): drivers/scsi/libsas/sas_discover.c: In function ‘sas_discover_domain’: ./include/linux/printk.h:309:2: warning: this statement may fall through [-Wimplicit-fallthrough=] printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/scsi/libsas/sas_discover.c:459:3: note: in expansion of macro ‘pr_notice’ pr_notice("ATA device seen but CONFIG_SCSI_SAS_ATA=N so cannot attach\n"); ^~~~~~~~~ drivers/scsi/libsas/sas_discover.c:462:2: note: here default: ^~~~~~~ Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
* Merge tag 'scsi-fixes' of ↵Linus Torvalds2019-07-201-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "This is the final round of mostly small fixes in our initial submit. It's mostly minor fixes and driver updates. The only change of note is adding a virt_boundary_mask to the SCSI host and host template to parametrise this for NVMe devices instead of having them do a call in slave_alloc. It's a fairly straightforward conversion except in the two NVMe handling drivers that didn't set it who now have a virtual infinity parameter added" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits) scsi: megaraid_sas: set an unlimited max_segment_size scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs scsi: IB/srp: set virt_boundary_mask in the scsi host scsi: IB/iser: set virt_boundary_mask in the scsi host scsi: storvsc: set virt_boundary_mask in the scsi host template scsi: ufshcd: set max_segment_size in the scsi host template scsi: core: take the DMA max mapping size into account scsi: core: add a host / host template field for the virt boundary scsi: core: Fix race on creating sense cache scsi: sd_zbc: Fix compilation warning scsi: libfc: fix null pointer dereference on a null lport scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized scsi: zfcp: fix request object use-after-free in send path causing wrong traces scsi: zfcp: fix request object use-after-free in send path causing seqno errors scsi: megaraid_sas: Update driver version to 07.710.50.00 scsi: megaraid_sas: Add module parameter for FW Async event logging scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers scsi: megaraid_sas: Fix calculation of target ID scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade ...
| * scsi: libsas: remove the exporting of sas_wait_ehDenis Efremov2019-07-121-1/+0
| | | | | | | | | | | | | | | | | | | | | | The function sas_wait_eh is declared static and marked EXPORT_SYMBOL, which is at best an odd combination. Because the function is not used outside of the drivers/scsi/libsas/sas_scsi_host.c file it is defined in, this commit removes the EXPORT_SYMBOL() marking. Signed-off-by: Denis Efremov <efremov@linux.com> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds2019-07-128-133/+27
|\| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs, mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the removal of the osst driver (I heard from Willem privately that he would like the driver removed because all his test hardware has failed). Plus number of minor changes, spelling fixes and other trivia. The big merge conflict this time around is the SPDX licence tags. Following discussion on linux-next, we believe our version to be more accurate than the one in the tree, so the resolution is to take our version for all the SPDX conflicts" Note on the SPDX license tag conversion conflicts: the SCSI tree had done its own SPDX conversion, which in some cases conflicted with the treewide ones done by Thomas & co. In almost all cases, the conflicts were purely syntactic: the SCSI tree used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the treewide conversion had used the new-style ones ("GPL-2.0-only" and "GPL-2.0-or-later"). In these cases I picked the new-style one. In a few cases, the SPDX conversion was actually different, though. As explained by James above, and in more detail in a pre-pull-request thread: "The other problem is actually substantive: In the libsas code Luben Tuikov originally specified gpl 2.0 only by dint of stating: * This file is licensed under GPLv2. In all the libsas files, but then muddied the water by quoting GPLv2 verbatim (which includes the or later than language). So for these files Christoph did the conversion to v2 only SPDX tags and Thomas converted to v2 or later tags" So in those cases, where the spdx tag substantially mattered, I took the SCSI tree conversion of it, but then also took the opportunity to turn the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag. Similarly, when there were whitespace differences or other differences to the comments around the copyright notices, I took the version from the SCSI tree as being the more specific conversion. Finally, in the spdx conversions that had no conflicts (because the treewide ones hadn't been done for those files), I just took the SCSI tree version as-is, even if it was old-style. The old-style conversions are perfectly valid, even if the "-only" and "-or-later" versions are perhaps more descriptive. * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits) scsi: qla2xxx: move IO flush to the front of NVME rport unregistration scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition scsi: qla2xxx: on session delete, return nvme cmd scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1 scsi: megaraid_sas: Introduce various Aero performance modes scsi: megaraid_sas: Use high IOPS queues based on IO workload scsi: megaraid_sas: Set affinity for high IOPS reply queues scsi: megaraid_sas: Enable coalescing for high IOPS queues scsi: megaraid_sas: Add support for High IOPS queues scsi: megaraid_sas: Add support for MPI toolbox commands scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD scsi: megaraid_sas: Handle sequence JBOD map failure at driver level scsi: megaraid_sas: Don't send FPIO to RL Bypass queue scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout scsi: megaraid_sas: Call disable_irq from process IRQ poll scsi: megaraid_sas: Remove few debug counters from IO path ...
| * scsi: libsas: aic94xx: hisi_sas: mvsas: pm8001: Use dev_is_expander()John Garry2019-06-203-25/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | Many times in libsas, and in LLDDs which use libsas, the check for an expander device is re-implemented or open coded. Use dev_is_expander() instead. We rename this from sas_dev_type_is_expander() to not spill so many lines in referencing. Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: no need to join wide port again in sas_ex_discover_dev()Jason Yan2019-06-191-22/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since we are processing events synchronously now, the second call of sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will be no races with other works in disco workqueue. So remove the second sas_ex_join_wide_port(). I did not change the return value of 'res' to error when discover failed because we need to continue to discover other phys if one phy discover failed. So let's keep that logic as before and just add a debug log to detect the failure. And directly return if second fanout expander attatched to the parent expander because it has nothing to do after the phy is disabled. Signed-off-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: switch remaining files to SPDX tagsChristoph Hellwig2019-05-219-141/+9
| | | | | | | | | | | | | | | | Use the the GPLv2 SPDX tag instead of verbose boilerplate text. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: switch sas_ata.[ch] to SPDX tagsChristoph Hellwig2019-05-211-15/+1
| | | | | | | | | | | | | | | | Use the the GPLv2+ SPDX tag instead of verbose boilerplate text. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: add a SPDX tag to sas_task.cChristoph Hellwig2019-05-211-1/+1
| | | | | | | | | | | | | | | | | | sas_task.c is the only libsas file missing licensing information. Add a GPLv2 tag for the default kernel license. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 372Thomas Gleixner2019-06-051-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation version 2 extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 135 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | Merge tag 'scsi-fixes' of ↵Linus Torvalds2019-06-022-2/+3
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Six minor fixes to device drivers and one to the multipath alua handler. The most extensive fix is the zfcp port remove prevention one, but it's impact is only s390" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: libsas: delete sas port if expander discover failed scsi: libsas: only clear phy->in_shutdown after shutdown event done scsi: scsi_dh_alua: Fix possible null-ptr-deref scsi: smartpqi: properly set both the DMA mask and the coherent DMA mask scsi: zfcp: fix to prevent port_remove with pure auto scan LUNs (only sdevs) scsi: zfcp: fix missing zfcp_port reference put on -EBUSY from port_remove scsi: libcxgbi: add a check for NULL pointer in cxgbi_check_route()
| * | scsi: libsas: delete sas port if expander discover failedJason Yan2019-05-301-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sas_port(phy->port) allocated in sas_ex_discover_expander() will not be deleted when the expander failed to discover. This will cause resource leak and a further issue of kernel BUG like below: [159785.843156] port-2:17:29: trying to add phy phy-2:17:29 fails: it's already part of another port [159785.852144] ------------[ cut here ]------------ [159785.856833] kernel BUG at drivers/scsi/scsi_transport_sas.c:1086! [159785.863000] Internal error: Oops - BUG: 0 [#1] SMP [159785.867866] CPU: 39 PID: 16993 Comm: kworker/u96:2 Tainted: G W OE 4.19.25-vhulk1901.1.0.h111.aarch64 #1 [159785.878458] Hardware name: Huawei Technologies Co., Ltd. Hi1620EVBCS/Hi1620EVBCS, BIOS Hi1620 CS B070 1P TA 03/21/2019 [159785.889231] Workqueue: 0000:74:02.0_disco_q sas_discover_domain [159785.895224] pstate: 40c00009 (nZcv daif +PAN +UAO) [159785.900094] pc : sas_port_add_phy+0x188/0x1b8 [159785.904524] lr : sas_port_add_phy+0x188/0x1b8 [159785.908952] sp : ffff0001120e3b80 [159785.912341] x29: ffff0001120e3b80 x28: 0000000000000000 [159785.917727] x27: ffff802ade8f5400 x26: ffff0000681b7560 [159785.923111] x25: ffff802adf11a800 x24: ffff0000680e8000 [159785.928496] x23: ffff802ade8f5728 x22: ffff802ade8f5708 [159785.933880] x21: ffff802adea2db40 x20: ffff802ade8f5400 [159785.939264] x19: ffff802adea2d800 x18: 0000000000000010 [159785.944649] x17: 00000000821bf734 x16: ffff00006714faa0 [159785.950033] x15: ffff0000e8ab4ecf x14: 7261702079646165 [159785.955417] x13: 726c612073277469 x12: ffff00006887b830 [159785.960802] x11: ffff00006773eaa0 x10: 7968702079687020 [159785.966186] x9 : 0000000000002453 x8 : 726f702072656874 [159785.971570] x7 : 6f6e6120666f2074 x6 : ffff802bcfb21290 [159785.976955] x5 : ffff802bcfb21290 x4 : 0000000000000000 [159785.982339] x3 : ffff802bcfb298c8 x2 : 337752b234c2ab00 [159785.987723] x1 : 337752b234c2ab00 x0 : 0000000000000000 [159785.993108] Process kworker/u96:2 (pid: 16993, stack limit = 0x0000000072dae094) [159786.000576] Call trace: [159786.003097] sas_port_add_phy+0x188/0x1b8 [159786.007179] sas_ex_get_linkrate.isra.5+0x134/0x140 [159786.012130] sas_ex_discover_expander+0x128/0x408 [159786.016906] sas_ex_discover_dev+0x218/0x4c8 [159786.021249] sas_ex_discover_devices+0x9c/0x1a8 [159786.025852] sas_discover_root_expander+0x134/0x160 [159786.030802] sas_discover_domain+0x1b8/0x1e8 [159786.035148] process_one_work+0x1b4/0x3f8 [159786.039230] worker_thread+0x54/0x470 [159786.042967] kthread+0x134/0x138 [159786.046269] ret_from_fork+0x10/0x18 [159786.049918] Code: 91322300 f0004402 91178042 97fe4c9b (d4210000) [159786.056083] Modules linked in: hns3_enet_ut(OE) hclge(OE) hnae3(OE) hisi_sas_test_hw(OE) hisi_sas_test_main(OE) serdes(OE) [159786.067202] ---[ end trace 03622b9e2d99e196 ]--- [159786.071893] Kernel panic - not syncing: Fatal exception [159786.077190] SMP: stopping secondary CPUs [159786.081192] Kernel Offset: disabled [159786.084753] CPU features: 0x2,a2a00a38 Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Reported-by: Jian Luo <luojian5@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * | scsi: libsas: only clear phy->in_shutdown after shutdown event doneJason Yan2019-05-301-2/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the event queue is full of phy up and down events and reached the threshold, we will queue a shutdown-event, and set phy->in_shutdown so that we will not queue a shutdown-event again. But before the shutdown-event can be executed, every phy-down event will clear phy->in_shutdown and a new shutdown-event will be queued. The queue will be full of these shutdown-events. Fix this by only clear phy->in_shutdown in sas_phye_shutdown(), that is after the first shutdown-event has been executed. Fixes: f12486e06ae8 ("scsi: libsas: shut down the PHY if events reached the threshold") Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 167Thomas Gleixner2019-05-302-33/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation version 2 of the license this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 83 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 156Thomas Gleixner2019-05-301-15/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1334 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 59Thomas Gleixner2019-05-243-54/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this file is licensed under gplv2 this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 5 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190520071858.561902672@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | treewide: Add SPDX license identifier for missed filesThomas Gleixner2019-05-211-0/+1
|/ | | | | | | | | | | | | | | | | Add SPDX license identifiers to all files which: - Have no license information of any form - Have EXPORT_.*_SYMBOL_GPL inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* scsi: libsas: Print expander PHY indexes in decimalJohn Garry2019-04-164-28/+27
| | | | | | | | | | | | | | Currently we print expander PHY indexes in a mix of decimal and hex. It is more consistent and also more convenient to read decimal, so make this change. We use width of 2 for expander and 1 for root PHYs prints. Some lines which were needlessly spilling multiple lines are unified. Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: Do discovery on empty PHY to update PHY infoJohn Garry2019-04-161-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | When we discover the PHY is empty in sas_rediscover_dev(), the PHY information (like negotiated linkrate) is not updated. As such, for a user examining sysfs for that PHY, they would see incorrect values: root@(none)$ cd /sys/class/sas_phy/phy-0:0:20 root@(none)$ more negotiated_linkrate 3.0 Gbit root@(none)$ echo 0 > enable root@(none)$ more negotiated_linkrate 3.0 Gbit So fix this, simply discover the PHY again, even though we know it's empty; in the above example, this gives us: root@(none)$ more negotiated_linkrate Phy disabled We must do this after unregistering the device associated with the PHY (in sas_unregister_devs_sas_addr()). Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: Inject revalidate event for root port eventJohn Garry2019-04-161-3/+21
| | | | | | | | | | | | | | | | | | According to the SAS spec, an expander device shall transmit BROADCAST (CHANGE) from at least one phy in each expander port other than the expander port that is the cause for transmitting BROADCAST (CHANGE). As such, for when the link is lost for a root PHY attached to an expander PHY, we get no broadcast event. This causes an issue for libsas, in that we will not revalidate the domain for these events. As a solution, for when a root PHY is formed or deformed from a root port, insert a broadcast event to trigger a domain revalidation. Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: Improve vague log in SAS rediscoveryJohn Garry2019-04-161-6/+14
| | | | | | | | | | | | | | | | | | | | | | When an expander PHY which was part of a wideport disconnects, we would see a log like this from sas_rediscover(): [ 39.695554] sas: phy20 part of wide port with phy16 Here, phy20 is the PHY that disconnected, and phy16 is the lowest indexed member PHY of the wideport. The log implies the phy20 is still part of the wideport with phy16, so is misleading or, at least, vague. Improve the logs in SAS rediscovery by removing this log and adding a log in sas_rediscover_dev() to tell what's really going on. While we're at it, also make the logs in sas_find_bcast_dev() more informative (and more consistent with the reset of the expander logs). Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: Try to retain programmed min linkrate for SATA min pathway ↵John Garry2019-04-161-1/+6
| | | | | | | | | | | | | | | | | | | | | unmatch fixing Currently for fixing the linkrate matching during discovery such that the linkrate of a SATA PHY does not exceed min pathway to initiator, we set the SATA PHY programmed min linkrate to the same value as the programmed max linkrate. This is unnecessary, and we should be able to keep the same programmed min linkrate if it is already lower than this new max programmed linkrate. This patch makes that change. In effect, this will not make much difference since we generally will negotiate a linkrate at the programmed max linkrate, and the programmed min linkrate will have no impact. Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: Stop hardcoding SAS address lengthJohn Garry2019-04-162-26/+29
| | | | | | | | | | | | | | Many times we use 8 for SAS address length, while we already have a macro for this - SAS_ADDR_SIZE. Replace instances of this with the macro. However, don't touch the SAS address array sizes sas.h, as these are defined according to the SAS spec. Some missing whitespaces are also added, and whitespace indentation in sas_hash_addr() is also fixed (see sas_hash_addr()). Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds2019-03-102-6/+34
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc, hisi_sas, target/iscsi and target/core. Additionally Christoph refactored gdth as part of the dma changes. The major mid-layer change this time is the removal of bidi commands and with them the whole of the osd/exofs driver and filesystem. This is a major simplification for block and mq in particular" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits) scsi: cxgb4i: validate tcp sequence number only if chip version <= T5 scsi: cxgb4i: get pf number from lldi->pf scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c scsi: mpt3sas: Add missing breaks in switch statements scsi: aacraid: Fix missing break in switch statement scsi: kill command serial number scsi: csiostor: drop serial_number usage scsi: mvumi: use request tag instead of serial_number scsi: dpt_i2o: remove serial number usage scsi: st: osst: Remove negative constant left-shifts scsi: ufs-bsg: Allow reading descriptors scsi: ufs: Allow reading descriptor via raw upiu scsi: ufs-bsg: Change the calling convention for write descriptor scsi: ufs: Remove unused device quirks Revert "scsi: ufs: disable vccq if it's not needed by UFS device" scsi: megaraid_sas: Remove a bunch of set but not used variables scsi: clean obsolete return values of eh_timed_out scsi: sd: Optimal I/O size should be a multiple of physical block size scsi: MAINTAINERS: SCSI initiator and target tweaks scsi: fcoe: make use of fip_mode enum complete ...
| * scsi: ata: Use unsigned int for cmd's type in ioctls in scsi_host_templateNathan Chancellor2019-02-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clang warns several times in the scsi subsystem (trimmed for brevity): drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to switch condition type (2147762695 to 18446744071562347015) [-Wswitch] case CCISS_GETBUSTYPES: ^ drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to switch condition type (2147762694 to 18446744071562347014) [-Wswitch] case CCISS_GETHEARTBEAT: ^ The root cause is that the _IOC macro can generate really large numbers, which don't fit into type 'int', which is used for the cmd parameter in the ioctls in scsi_host_template. My research into how GCC and Clang are handling this at a low level didn't prove fruitful. However, looking at the rest of the kernel tree, all ioctls use an 'unsigned int' for the cmd parameter, which will fit all of the _IOC values in the scsi/ata subsystems. Make that change because none of the ioctls expect a negative value for any command, it brings the ioctls inline with the reset of the kernel, and it removes ambiguity, which is never good when dealing with compilers. Link: https://github.com/ClangBuiltLinux/linux/issues/85 Link: https://github.com/ClangBuiltLinux/linux/issues/154 Link: https://github.com/ClangBuiltLinux/linux/issues/157 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Bradley Grove <bgrove@attotech.com> Acked-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Remove scsi_to_u32()Bart Van Assche2019-01-291-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | Since the function scsi_to_u32() is identical to get_unaligned_be32(), change all scsi_to_u32() calls into get_unaligned_be32() calls. Cc: Jian Luo <luojian5@huawei.com> Cc: John Garry <john.garry@huawei.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Support SATA PHY connection rate unmatch fixing during discoveryJohn Garry2019-01-121-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +----------+ +----------+ | | | | | |--- 3.0 G ---| |--- 6.0 G --- SAS disk | | | | | |--- 3.0 G ---| |--- 6.0 G --- SAS disk |initiator | | | | device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk | | | | | |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect | | | | | | | |--- 6.0 G --- SATA disk -->failed to connect | | | | +----------+ +----------+ According to Serial Attached SCSI - 1.1 (SAS-1.1): If an expander PHY attached to a SATA PHY is using a physical link rate greater than the maximum connection rate supported by the pathway from an STP initiator port, a management application client should use the SMP PHY CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL LINK RATE field of the expander PHY to the maximum connection rate supported by the pathway from that STP initiator port. Currently libsas does not support checking if this condition occurs, nor rectifying when it does. Such a condition is not at all common, however it has been seen on some pre-silicon environments where the initiator PHY only supports a 1.5 Gbit maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy. This patch adds support for checking and rectifying this condition during initial device discovery only. We do support checking min pathway connection rate during revalidation phase, when new devices can be detected in the topology. However we do not support in the case of the the user reprogramming PHY linkrates, such that min pathway condition is not met/maintained. A note on root port PHY rates: The libsas root port PHY rates calculation is broken. Libsas sets the rates (min, max, and current linkrate) of a root port to the same linkrate of the first PHY member of that same port. In doing so, it assumes that all other PHYs which subsequently join the port to have the same negotiated linkrate, when they could actually be different. In practice this doesn't happen, as initiator and expander PHYs are normally initialised with consistent min/max linkrates. This has not caused an issue so far, so leave alone for now. Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Check SMP PHY control function resultJohn Garry2019-01-121-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the SMP PHY control execution result is checked, however the function result for the command is not. As such, we may be missing all potential errors, like SMP FUNCTION FAILED, INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has failed. In some scenarios we need to ensure the function result is accepted, so add a check for this. Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attachedJohn Garry2019-02-161-0/+2
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sysfs phy_identifier attribute for a sas_end_device comes from the rphy phy_identifier value. Currently this is not being set for rphys with an end device attached, so we see incorrect symlinks from systemd disk/by-path: root@localhost:~# ls -l /dev/disk/by-path/ total 0 lrwxrwxrwx 1 root root 9 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0 -> ../../sdb lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part2 -> ../../sdb2 lrwxrwxrwx 1 root root 10 Feb 13 12:26 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy0-lun-0-part3 -> ../../sdc3 Indeed, each sas_end_device phy_identifier value is 0: root@localhost:/# more sys/class/sas_device/end_device-0\:0\:2/phy_identifier 0 root@localhost:/# more sys/class/sas_device/end_device-0\:0\:10/phy_identifier 0 This patch fixes the discovery code to set the phy_identifier. With this, we now get proper symlinks: root@localhost:~# ls -l /dev/disk/by-path/ total 0 lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy10-lun-0 -> ../../sdg lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy11-lun-0 -> ../../sdh lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0 -> ../../sda lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy2-lun-0-part1 -> ../../sda1 lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0 -> ../../sdb lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy3-lun-0-part2 -> ../../sdb2 lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0 -> ../../sdc lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part1 -> ../../sdc1 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part2 -> ../../sdc2 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy4-lun-0-part3 -> ../../sdc3 lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy5-lun-0 -> ../../sdd lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0 -> ../../sde lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part1 -> ../../sde1 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part2 -> ../../sde2 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy7-lun-0-part3 -> ../../sde3 lrwxrwxrwx 1 root root 9 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0 -> ../../sdf lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part1 -> ../../sdf1 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part2 -> ../../sdf2 lrwxrwxrwx 1 root root 10 Feb 13 11:53 platform-HISI0162:01-sas-exp0x500e004aaaaaaa1f-phy8-lun-0-part3 -> ../../sdf3 Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Reported-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Jason Yan <yanaijie@huawei.com> Tested-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds2018-12-2813-348/+233
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: smarpqi, lpfc, qedi, megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have a pile of annotation, unused variable and minor updates. The big API change is the updates for Christoph's DMA rework which include removing the DISABLE_CLUSTERING flag. And finally there are a couple of target tree updates" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits) scsi: isci: request: mark expected switch fall-through scsi: isci: remote_node_context: mark expected switch fall-throughs scsi: isci: remote_device: Mark expected switch fall-throughs scsi: isci: phy: Mark expected switch fall-through scsi: iscsi: Capture iscsi debug messages using tracepoints scsi: myrb: Mark expected switch fall-throughs scsi: megaraid: fix out-of-bound array accesses scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through scsi: fcoe: remove set but not used variable 'port' scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown() scsi: smartpqi: fix build warnings scsi: smartpqi: update driver version scsi: smartpqi: add ofa support scsi: smartpqi: increase fw status register read timeout scsi: smartpqi: bump driver version scsi: smartpqi: add smp_utils support scsi: smartpqi: correct lun reset issues scsi: smartpqi: correct volume status scsi: smartpqi: do not offline disks for transient did no connect conditions scsi: smartpqi: allow for larger raid maps ...
| * scsi: libsas: Remove pcidev referenceJohn Garry2018-11-151-1/+1
| | | | | | | | | | | | | | | | Not all host drivers are PCI drivers - like hisi_sas, which supports a platform driver - so remove reference to "pcidev". Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Drop SAS_DPRINTK() and revise logs levelsJohn Garry2018-11-159-236/+207
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like sas_printk() did previously, SAS_DPRINTK() offers little value now that libsas logs already have the "sas" prefix through pr_fmt(fmt). So it can be dropped. However, after reviewing some logs in libsas, it is noticed that debug level is too low in many instances. So this change drops SAS_DPRINTK() and revises some logs to a more appropriate level. However many stay at debug level, although some are significantly promoted. We add -DDEBUG for compilation so that we keep the debug messages by default, as before. All the pre-existing checkpatch errors for spanning messages across multiple lines are also fixed. Finally, all other references to printk() [apart from special formatting in sas_ata.c] are removed and replaced with appropriate pr_xxx(). Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Drop sas_printk()John Garry2018-11-154-20/+16
| | | | | | | | | | | | | | | | | | | | | | | | The printk wrapper sas_printk() adds little value now that libsas logs already have the "sas" prefix through pr_fmt(fmt), so just use pr_notice() directly. In addition, strings which span multiple lines are reunited. Originally-from: Joe Perches <joe@perches.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Use pr_fmt(fmt)John Garry2018-11-153-3/+15
| | | | | | | | | | | | | | | | | | In preparation for dropping the libsas printk wrappers, use pr_fmt(fmt) declaration to add the framework log prefix - "sas". Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| * scsi: libsas: Delete sas_dump.{c, h}John Garry2018-11-154-94/+0
| | | | | | | | | | | | | | The code in these files is not longer referenced, so delete them. Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* | block: don't hold the queue_lock over blk_abort_requestChristoph Hellwig2018-11-152-13/+2
|/ | | | | | | | | There is nothing it could synchronize against, so don't go through the pains of acquiring the lock. Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* scsi: libsas: fix a race condition when smp task timeoutJason Yan2018-09-261-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When the lldd is processing the complete sas task in interrupt and set the task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be triggered at the same time. And smp_task_timedout() will complete the task wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed before lldd end the interrupt process. Thus a use-after-free will happen. Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not set. And remove the check of the return value of the del_timer(). Once the LLDD sets DONE, it must call task->done(), which will call smp_task_done()->complete() and the task will be completed and freed correctly. Reported-by: chenxiang <chenxiang66@hisilicon.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: check the ata device status by ata_dev_enabled()Jason Yan2018-09-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The libata reported like: [113518.620433] ata5.00: qc timeout (cmd 0xec) [113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4) But libsas verifies the device status by ata_dev_disabled(), which skipped ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed the device cannot be actually brought up. And even the new bcast of this device will be considered as flutter and will not probe this device again. Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with this if the ata device probe failed. New bcasts can let us try to probe the device again and bring it up if it is fine to IDENTIFY. Tested-by: Zhou Yupeng <zhouyupeng1@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: always unregister the old device if going to discover newJason Yan2018-09-261-8/+5
| | | | | | | | | | | | | | | | | | | | | | If we went into sas_rediscover_dev() the attached_sas_addr was already insured not to be zero. So it's unnecessary to check if the attached_sas_addr is zero. And although if the sas address is not changed, we always have to unregister the old device when we are going to register a new one. We cannot just leave the device there and bring up the new. Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: chenxiang <chenxiang66@hisilicon.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: make the lldd_port_deformed method optionalJason Yan2018-09-261-1/+1
| | | | | | | | | | | | | | | | | | | | Now LLDDs have to implement lldd_port_deformed method otherwise NULL dereference will happen. Make it optional and remove the dummy implementation in hisi_sas. Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Acked-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: read host_busy via scsi_host_busy()Ming Lei2018-06-261-2/+2
| | | | | | | | | | | | | | | | | | | | | | No functional change. Just introduce scsi_host_busy() and replace the direct read of scsi_host->host_busy with this new API. Cc: Omar Sandoval <osandov@fb.com>, Cc: "Martin K. Petersen" <martin.petersen@oracle.com>, Cc: James Bottomley <james.bottomley@hansenpartnership.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: Don Brace <don.brace@microsemi.com> Cc: Kashyap Desai <kashyap.desai@broadcom.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Laurence Oberman <loberman@redhat.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: dynamically allocate and free ata hostJason Yan2018-06-202-14/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced refcounting to ata_host and will increase or decrease the refcount when adding or deleting transport ATA port. Now the ata host for libsas is embedded in domain_device, and the ->kref member is not initialized. Afer we add ata transport class, ata_host_get() will be called when adding transport ATA port and a warning will be triggered as below: refcount_t: increment on 0; use-after-free. WARNING: CPU: 2 PID: 103 at lib/refcount.c:153 refcount_inc+0x40/0x48 ...... Call trace: refcount_inc+0x40/0x48 ata_host_get+0x10/0x18 ata_tport_add+0x40/0x120 ata_sas_tport_add+0xc/0x14 sas_ata_init+0x7c/0xc8 sas_discover_domain+0x380/0x53c process_one_work+0x12c/0x288 worker_thread+0x58/0x3f0 kthread+0xfc/0x128 ret_from_fork+0x10/0x18 And also when removing transport ATA port ata_host_put() will be called and another similar warning will be triggered. If the refcount decreased to zero, the ata host will be freed. But this ata host is only part of domain_device, it cannot be freed directly. So we have to change this embedded static ata host to a dynamically allocated ata host and initialize the ->kref member. To use ata_host_get() and ata_host_put() in libsas, we need to move the declaration of these functions to the public libata.h and export them. Fixes: b6240a4df018 ("scsi: libsas: add transport class for ATA devices") Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Taras Kondratiuk <takondra@cisco.com> CC: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* scsi: libsas: remove irq save in sas_ata_qc_issue()Sebastian Andrzej Siewior2018-06-201-6/+1
| | | | | | | | | | | | | | | | | | Since commit 312d3e56119a ("[SCSI] libsas: remove ata_port.lock management duties from lldds") the sas_ata_qc_issue() function unlocks the ata_port.lock and disables interrupts before doing so. That lock is always taken with disabled interrupts so at this point, the interrupts are already disabled. There is no need to disable the interrupts before the unlock operation because they are already disabled. Restoring the interrupt state later does not change anything because they were disabled and remain disabled. Therefore remove the operations which do not change the behaviour. Fixes: 312d3e56119a ("[SCSI] libsas: remove ata_port.lock management duties from lldds") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* treewide: kzalloc() -> kcalloc()Kees Cook2018-06-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* scsi: libsas: add transport class for ATA devicesJason Yan2018-04-192-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now ata devices attached with sas controller do not have transport class, so that we can not see any information of these ata devices in /sys/class/ata_port(or ata_link or ata_device). Add transport class for the ata devices attached with sas controller. The /sys/class directory will show the infomation of the ata devices as follows: localhost:/sys/class # ls ata* ata_device: dev1.0 dev2.0 ata_link: link1 link2 ata_port: ata1 ata2 No functional change of the device scanning and io path. The ata transport class was deleted when destroying the sas devices. Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Merge branch 'fixes' into miscJames Bottomley2018-04-041-20/+13
|\ | | | | | | | | | | | | | | | | | | Somewhat nasty merge due to conflicts between "33b28357dd00 scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc scsi: qla2xxx: Fix FC-NVMe LUN discovery" Merge is non-trivial and has been verified by Qlogic (Cavium) Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
| * scsi: libsas: defer ata device eh commands to libataJason Yan2018-03-131-20/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When ata device doing EH, some commands still attached with tasks are not passed to libata when abort failed or recover failed, so libata did not handle these commands. After these commands done, sas task is freed, but ata qc is not freed. This will cause ata qc leak and trigger a warning like below: WARNING: CPU: 0 PID: 28512 at drivers/ata/libata-eh.c:4037 ata_eh_finish+0xb4/0xcc CPU: 0 PID: 28512 Comm: kworker/u32:2 Tainted: G W OE 4.14.0#1 ...... Call trace: [<ffff0000088b7bd0>] ata_eh_finish+0xb4/0xcc [<ffff0000088b8420>] ata_do_eh+0xc4/0xd8 [<ffff0000088b8478>] ata_std_error_handler+0x44/0x8c [<ffff0000088b8068>] ata_scsi_port_error_handler+0x480/0x694 [<ffff000008875fc4>] async_sas_ata_eh+0x4c/0x80 [<ffff0000080f6be8>] async_run_entry_fn+0x4c/0x170 [<ffff0000080ebd70>] process_one_work+0x144/0x390 [<ffff0000080ec100>] worker_thread+0x144/0x418 [<ffff0000080f2c98>] kthread+0x10c/0x138 [<ffff0000080855dc>] ret_from_fork+0x10/0x18 If ata qc leaked too many, ata tag allocation will fail and io blocked for ever. As suggested by Dan Williams, defer ata device commands to libata and merge sas_eh_finish_cmd() with sas_eh_defer_cmd(). libata will handle ata qcs correctly after this. Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: Xiaofei Tan <tanxiaofei@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-18 10:16:38 +0100