| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
Baudrate calculation depends on requested baudrate and uart clock.
This patch is checking that uartclk is also passed.
The same logic is used 8250_early.c/init_port function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The platform_get_irq can return error. Assigning the return value to an
unsigned variable and checking it for negative value will always return
false.
Use an intermediate signed variable to get IRQ information, check for any
error and then assign it to 'irq' variable inside uart_port structure.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 99492c39f39f ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol. This
fix was based on commit 07fca0e57fca92 ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.
However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format. In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array. If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".
To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
3d56e331b653 ("tracing: Replace syscall_meta_data struct array with pointer array")
654986462939 ("tracepoints: Fix section alignment using pointer array")
e4a9ea5ee7c8 ("tracing: Replace trace_event struct array with pointer array")
Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.
Fixes: 99492c39f39f ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To reset the UART the SRST needs be cleared (low active). According
to the documentation the bit will remain active for 4 module clocks
until it is cleared (set to 1).
Hence the real register need to be read in case the cached register
indicates that the SRST bit is zero.
This bug lead to wrong baudrate because the baud rate register got
restored before reset completed in imx_flush_buffer.
Fixes: 3a0ab62f43de ("serial: imx: implement shadow registers for UCRx and UFCR")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When using half-duplex mode (which disables receiver during txing)
the RTS signal cannot be driven low during transmission when using
i.MX UART RTS/CTS control. This seems to be a limitation of the
i.MX UART IP: The RTS (CTS_B) signal is controlled by the receiver.
When the receiver is disabled, the signal stays in UART logic idle
state which is high...
If SER_RS485_RTS_ON_SEND is used, RTS needs to be high active during
transmission. Since this is the default state of the RTS (CTS_B)
signal when the receiver is off, half-duplex mode in this
configuration works fine.
However, a low-active RTS signal (flag SER_RS485_RTS_ON_SEND not set)
cannot be generated when the receiver is turned off.
Print an error if the user selects this unsupported configuration
(both SER_RS485_RTS_ON_SEND and SER_RS485_RX_DURING_TX unset) and
configure the closest working configuration (set the
SER_RS485_RX_DURING_TX flag).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 68a0db1d7da2 reworked the baud rate selection, but also added
a (not so) subtle change in the way the local flags (c_lflag in the
termios structure) are handled, forcing the new flags to always be the
same as the old ones.
The reason for that particular change is both obscure and undocumented.
It also completely breaks userspace. Something as trivial as getty is
unusable:
<example>
Debian GNU/Linux 9 sy-borg ttyMV0
sy-borg login: root
root
[timeout]
Debian GNU/Linux 9 sy-borg ttyMV0
</example>
which is quite obvious in retrospect: getty cannot get in control of
the echo mode, is stuck in canonical mode, and times out without ever
seeing anything valid. It also begs the question of how this change was
ever tested.
The fix is pretty obvious: stop messing with c_lflag, and the world
will be a happier place.
Cc: stable@vger.kernel.org # 4.15+
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The buf_overrun count is only every written, and not exposed to
userspace anywhere. This means that dropped characters due to flip
buffer overruns are never visible to userspace.
The /proc/tty/driver/serial file exports a bunch of metrics (including
hardware overruns) already, so add the buf_overrun (as "bo:") to this
file.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fixes missing characters on kernel console at low baud rates (i.e.9600).
The driver should poll TX_RDY or TX_FIFO_EMP instead of TX_EMP to ensure
that the transmitter holding register (THR) is ready to receive a new byte.
TX_EMP tells us when it is possible to send a break sequence via
SND_BRK_SEQ. While this also indicates that both the THR and the TSR are
empty, it does not guarantee that a new byte can be written just yet.
Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gabriel Matni <gabriel.matni@exfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In case of error, the function platform_get_resource() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\
| | |
| | |
| | |
| | |
| | | |
We want the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This driver supports GENI based UART Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including UART. This driver support console
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Doug Anderson <dianders@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.
Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Configure RS485 mode during port initialization.
Fixes: 1bcda09d2910 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since dtc v1.4.6-9-gaadd0b65c987, aliases property name
must include only lowercase and '-'.
After having updated all STi boards serial aliases from "ttyASN"
to "serialN", st-asc driver need to be updated accordingly as tty
aliases id is retrieved using of_alias_get_id().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Implement Driver Enable signal (DE) to activate the transmission mode
of the external transceiver.
Signed-off-by: Yves Coppeaux <yves.coppeaux@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In case of Alphascale ASM9260 probe() enables s->clk and s->clk_ahb
via mxs_get_clks(), but there is no disable of the clocks.
The patch adds it to error paths and to mxs_auart_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 254da0d753fb ("serial: mxs-auart: add Alphascale ASM9260 support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Special settings for APMC0D08 are applied when device is present
in the system. To check its presence we may use acpi_dev_present()
instead of current open coded variant.
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Having a fixed prefix helps at several places. It ensures that another
driver doesn't use the same function name which confuses the linker and
tools like ctags. It simplifies working with function tracing and
dynamic printk() support which can filter on function names. And last
but not least it helps the human source code reader to understand if a
given function belongs to a driver or a more general part of the kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
serial_core might call the .start_tx callback without any data being
available to send. In this case return early instead of going through
all the setup needed for sending which might include disabling RX in
RS485 half-duplex mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When using RS485 half duplex the Transmitter Complete irq is needed to
determine the moment when the transmitter can be disabled. When using
DMA this irq must only be enabled when DMA has completed to transfer all
data. Otherwise the CPU might busily trigger this irq which is not
properly handled and so the also pending irq for the DMA transfer cannot
trigger.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This allows to increase the RX waterlevel which allows to delay the RRDY
irq. The desired effect is that less irqs are needed to handle
characters and so reduce irq count of the system.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make sure that UCR1.RXDMAEN and UCR1.ATDMAEN (for the DMA case) and
UCR1.RRDYEN (for the PIO case) are off iff UCR1.RXEN is disabled. This
ensures that the fifo isn't read with RX disabled which results in an
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When the UART is used in DMA mode, .stop_rx() does nothing if the port
isn't suspended. This is wrong as .stop_rx() should stop receiving
characters unconditionally. When the port is about to be closed the DMA
channel is stopped in .shutdown(), so this isn't necessary to be in
.stop_rx() here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The aging timer fires if there are characters in the RX fifo but the
water level isn't reached yet. Make sure that the waterlevel is
configured before the aging timer is enabled to trigger a DMA request
(UCR1_ATDMAEN).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The serial/imx driver is full of inconsistently named and typed
variables that hold different register values.
Consistently use u32 as type (matching what readl and writel use) and
name the variables after the register whose value they are holding.
This makes it easier to notice when UCR2_RTSEN is written to UCR1.
The only difference introduced by this commit in the compiled driver is
that twice the second argument to warn_slowpath_null() changed because the
two WARN_ON in dma_rx_callback() pass __LINE__ to warn_slowpath_null().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The original code looks as follows:
if (sport->dma_is_enabled) {
... make sure TX DMA is running, i.e. .dma_is_txing = 1
}
if (sport->dma_is_txing)
return;
As .dma_is_txing can only be true if .dma_is_enabled is, the return can
go at the end of the first if body without an additional check.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Neither .dma_is_txing nor .dma_is_rxing can evaluate to true if
.dma_is_enabled evaluates to false:
The only function that sets .dma_is_txing to a non-zero value is
imx_dma_tx() which is only called if .dma_is_enabled is true. Same for
.dma_is_rxing and start_rx_dma(). And before .dma_is_enabled is set to 0
when imx_shutdown calls imx_disable_dma(), .dma_is_rxing and
.dma_is_txing are reset to zero before, too.
For this reason
sport->dma_is_enabled && sport->dma_is_rxing
has the same value as
sport->dma_is_rxing
which allows to simplify three if conditions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reduces the amount of read accesses to the register space by
shadowing the values for five registers that only change on writing
them. There is a single bit in UCR2 that might change without being
written to it, this is handled accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This prepares implementing shadow copies for the control registers and
additionally provides a good place to hook in debug code to trace
register usage.
Most of this patch was done using pattern substitution:
perl -p -i -e '
s/\breadl(?:_relaxed)?\((?:sport->port\.|port->)membase \+/imx_uart_readl(sport,/;
s/\bwritel(?:_relaxed)?\(([^,]*), (sport->port\.|port->)membase \+/imx_uart_writel(sport, $1,/;
' drivers/tty/serial/imx.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Consistently indicate being called with irqs off and the port lock taken
for all functions that this applies to.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Only the reference manual for the i.MX1 (I have MC9328MX1RM/D Rev 5 from
2004) uses TDMAEN and RDMAEN for these. All reference manuals for the
newer chips use TXDMAEN and RXDMAEN. Update to the newer name with the
assumption that most imx users don't use an imx1 any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
PCI ID database is for IDs used across several drivers.
Here is the case for SUNIX combo cards.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The cdns_uart_port[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 928e9263492069ee ("tty: xuartps: Initialize ports according to aliases")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The sirf_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: a6ffe8966acbb66b ("serial: sirf: use dynamic method allocate uart structure")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The sci_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a
legitimate DTB.
Fixes: 97ed9790c514066b ("serial: sh-sci: Remove unused platform data capabilities field")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The s3c24xx_serial_ports[] array is indexed using a value derived from
the "serialN" alias in DT, or from an incrementing probe index, which
may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using
a legitimate DTB or legitimate board code.
Fixes: 13a9f6c64fdc55eb ("serial: samsung: Consider DT alias when probing ports")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The serial_pxa_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 699c20f3e6310aa2 ("serial: pxa: add OF support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The auart_port[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: 1ea6607d4cdc9179 ("serial: mxs-auart: Allow device tree probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07225ab6 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb0ba5d2 ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The arc_uart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Note that the array size is defined by a Kconfig symbol
(CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a
legitimate DTB.
Fixes: ea28fd56fcde69af ("serial/arc-uart: switch to devicetree based probing")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after
imx_shudown() completes, .dma_is_enabled is zero. For this reason
.dma_is_enabled is also zero when imx_startup() is called. So the check
for this variable being zero can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The .dma_is_inited member is only set to a value != 0 when the port's
startup function calls imx_uart_dma_init(). On shutdown of the port
imx_uart_dma_exit is called which sets the value back to 0. So
.dma_is_inited is always 0 when imx_startup() is called (assuming
.startup() and .shutdown() are correctly balanced) and the check for
!sport->dma_is_inited can go away.
This allows to replace .dma_is_inited by a variable local to
imx_startup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Handling an irq that isn't enabled can have some undesired side effects.
Some of these are mentioned in the newly introduced code comment. Some
of the irq sources already had their handling right, some don't. Handle
them all in the same consistent way.
The change for USR1_RRDY and USR1_AGTIM drops the check for
dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always
off if dma is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Now the variable holding the value of register USR1 is called usr1
instead of sts which is more straight forward. The same is also done for
sts2 which is called usr2 now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The check sts & USR1_DTRD was just evaluated to true two lines above.
So this change doesn't have any effect on the semantic of the driver.
Fixes: 27e16501052e ("serial: imx: implement DSR irq handling for DTE mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Bit pattern STAT_FRM_ERR is being bit-wise or'd twice; remove the
redundant 2nd STAT_FRM_ERR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This allows me to login after sending a break when service
serial-getty@ttymxc0.service is running
The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors
fixes this by allowing the higher layers to see a break.
Also, call uart_handle_break to handle possible
"secure attention key."
FYI: Martin said the ROM sdma firmware works with this patch,
but external sdma firmware still does not send breaks on a
i.mx6UL
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Martin Hicks <mort@bork.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
