summaryrefslogtreecommitdiffstats
path: root/drivers/usb/chipidea (follow)
Commit message (Collapse)AuthorAgeFilesLines
* usb: chipidea: udc: using MultO at TD as real mult value for ISO-TXPeter Chen2014-01-141-2/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have met a bug that the high bandwidth ISO-TX transfer has failed at the last packet if it is less than 1024, the TD status shows it is "Transaction Error". The root cause of this problem is: the mult value at qh is not correct for current TD's transfer length. We use TD list to queue un-transfer TDs, and change mult for new adding TDs. If new adding TDs transfer length less than 1024, but the queued un-transfer TDs transfer length is larger than 1024, the transfer error will occur, and vice versa. Usually, this problem occurs at the last packet, and the first packet for new frame. We fixed this problem by setting Mult at QH as the largest value (3), and set MultO (Multiplier Override) at TD according to every transfer length. It can cover both hardware version less than 2.3 (the real mult is MultO if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)). Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior unchanged. For stable tree: 3.11+. Cc: stable <stable@vger.kernel.org> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Reported-by: Matthieu Vanin <b47495@freescale.com> Tested-by: Matthieu Vanin <b47495@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: need to mask INT_STATUS when write otgscPeter Chen2014-01-141-3/+3
| | | | | | | | | | | | | | For otgsc, both enable bits and status bits are in it. So we need to make sure the status bits are not be cleared when write enable bits. It can fix one bug that we plug in/out Micro AB cable fast, and sometimes, the IDIS will be cleared wrongly when handle last ID interrupt (ID 0->1), so the current interrupt will not occur. For stable tree: 3.12+ Cc: stable@vger.kernel.org Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: put hw_phymode_configure before ci_usb_phy_initChris Ruehl2014-01-141-2/+2
| | | | | | | | | | | hw_phymode_configure configures the PORTSC registers and allow the following phy_inits to operate on the right parameters. This fix a problem where the UPLI (ISP1504) could not be detected, because the Viewport was not available and read the viewport return 0's only. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flagChris Ruehl2014-01-141-3/+5
| | | | | | | | | | | | | | * init the sts flag to 0 (missed) * fix write the real bit not sts value * Set PORTCS_STS and DEVLC_STS only if sts = 1 [Peter Chen: This one and the next patch fix the problem occurred imx27 and imx31, and imx27 and imx31 usb support are enabled until 3.14, so these two patches isn't needed for -stable] Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28Peter Chen2014-01-141-6/+26
| | | | | | | | | | | | | | Due to imx28 needs ARM swp instruction for writing, we set CI_HDRC_IMX28_WRITE_FIX for imx28. This patch is needed for stable tree 3.11+ Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: add freescale imx28 special write register methodPeter Chen2014-01-143-2/+27
| | | | | | | | | | | | | | | | | | | According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB register error issue", All USB register write operations must use the ARM SWP instruction. So, we implement special hw_write and hw_test_and_clear for imx28. Discussion for it at below: http://marc.info/?l=linux-usb&m=137996395529294&w=2 This patch is needed for stable tree 3.11+. Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"Greg Kroah-Hartman2014-01-081-26/+6
| | | | | | | | | | | This reverts commit 30666249eae3b04875d514dea557d1ab1468c006, as it depended on a previous patch that I rejected, causing a build error here. Sorry about that. Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Peter Chen <peter.chen@freescale.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28Peter Chen2014-01-081-6/+26
| | | | | | | | | | Due to imx28 needs ARM swp instruction for writing, we set CI_HDRC_IMX28_WRITE_FIX for imx28. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: mark register map as "const" and convert to u8Marc Kleine-Budde2014-01-081-40/+40
| | | | | | | | | | This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as "const". Further, as all offset fit into a single byte, the type is changed from uintptr_t to u8. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: move malloced regmap directly into struct hw_bankMarc Kleine-Budde2014-01-082-41/+30
| | | | | | | | | | | Without this patch a seperate chunk of memory is allocated for the regmap array. As the regmap is always used it makes no sense to allocate a seperate memory block for it, this patch moves the regmap array directly into the struct hw_bank. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: chipidea: add guard macro to ci_hdrc_imx.hRahul Bedarkar2014-01-031-0/+5
| | | | | | | Add guard macro to driver/usb/chipidea/ci_hdrc_imx.h Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'usb-for-v3.14' of ↵Greg Kroah-Hartman2014-01-031-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: changes for v3.14 merge window This pull request is quite extensive, containing 105 non-merge commits. Because of that, we describe the changes in sections below: New drivers: - Keystone PHY driver and DWC3 Glue Layer - Aeroflex Gaisler GRUSBDC - Tahvo PHY driver for N770 - JZ4740 MUSB gluer Layer - Broadcom PHY Driver Important new features: - MUSB DSPS learned about suspend/resume - New quirk_ep_out_aligned_size flag added to struct usb_gadget - DWC3 initializes the new quirk flag so gadget drivers can use it. - AM335x PHY Driver learns about remote wakeup - Renesas USBHS now requests DMA Engine only once - s3c-hsotg is now re-used on Broadcom devices - USB PHY layer now makes sure to initialize the notifier for all drivers - omap-control learned about TI's new AM437x devices - few other usb gadget/function drivers learned about the new configfs-based binding. Misc Fixes and Clean Ups: - Several sparse fixes all over the place - Removal of redundant of_match_ptr() - r-car gen2 phy now uses usb_add_phy_dev() - removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers - conversion to clk_prepare/clk_unprepare on r8a66597-udc - some randconfig errors and build warnings were fixed - removal of unnecessary lock on dwc3-omap.c Signed-of-by: Felipe Balbi <balbi@ti.com>
| * Merge tag 'v3.13-rc5' into nextFelipe Balbi2013-12-233-4/+6
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linux 3.13-rc5 * tag 'v3.13-rc5': (231 commits) Linux 3.13-rc5 aio: clean up and fix aio_setup_ring page mapping aio/migratepages: make aio migrate pages sane aio: fix kioctx leak introduced by "aio: Fix a trinity splat" Don't set the INITRD_COMPRESS environment variable automatically mm: fix build of split ptlock code pstore: Don't allow high traffic options on fragile devices mm: do not allocate page->ptl dynamically, if spinlock_t fits to long mm: page_alloc: revert NUMA aspect of fair allocation policy Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy" mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure target: Remove extra percpu_ref_init arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h target/file: Update hw_max_sectors based on current block_size iser-target: Move INIT_WORK setup into isert_create_device_ib_res iscsi-target: Fix incorrect np->np_thread NULL assignment mm/hugetlb: check for pte NULL pointer in __page_check_address() fix build with make 3.80 ... Conflicts: drivers/usb/phy/Kconfig
| * | usb: gadget: add "maxpacket_limit" field to struct usb_epRobert Baldyga2013-12-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds "maxpacket_limit" to struct usb_ep. This field contains maximum value of maxpacket supported by driver, and is set in driver probe. This value should be used by autoconfig() function, because value of field "maxpacket" is set to value from endpoint descriptor when endpoint becomes enabled. So when autoconfig() function will be called again for this endpoint, "maxpacket" value will contain wMaxPacketSize from descriptior instead of maximum packet size for this endpoint. For this reason this patch adds new field "maxpacket_limit" which contains value of maximum packet size (which defines maximum endpoint capabilities). This value is used in ep_matches() function used by autoconfig(). Value of "maxpacket_limit" should be set in UDC driver probe function, using usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function set choosen value to both "maxpacket_limit" and "maxpacket" fields. This patch modifies UDC drivers by adding support for maxpacket_limit. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* | | Merge 3.13-rc5 into usb-nextGreg Kroah-Hartman2013-12-242-3/+4
|\ \ \ | | |/ | |/| | | | | | | | | | This resolves the merge issue with drivers/usb/host/ohci-at91.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: fix nobody cared IRQ when booting with host rolePeter Chen2013-12-092-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If we connect Male-A-To-Male-A cable between otg-host and host pc, the ci->vbus_active is set wrongly, and cause the controller run at peripheral mode when we load gadget module (ci_udc_start will be run), but the software runs at host mode due to id = 0. The ehci_irq can't handle suspend (USBi_SLI) interrupt which is enabled for peripheral mode, it causes no one will handle irq error. This patch is needed for 3.12 stable Cc: stable <stable@vger.kernel.org> Acked-by: Michael Grzeschik <mgr@pengutronix.de> Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: host: Only disable the vbus regulator if it is not NULLFabio Estevam2013-12-091-1/+2
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 40ed51a4b (usb: chipidea: host: add vbus regulator control) introduced a smatch complaint because regulator_disable() is called without checking whether ci->platdata->reg_vbus is not NULL. Fix this by adding the check. This patch is needed for 3.12 stable Cc: stable <stable@vger.kernel.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: usbmisc: Add support for i.MX51 CPUAlexander Shiyan2013-12-091-0/+4
| | | | | | | | | | | | | | | | | | | | This adds i.MX51 as the next user of the usbmisc driver. Functionality is similar to i.MX53, so at this stage simply reuse existing i.MX53 calls. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: usbmisc: Add support for i.MX27/i.MX31 CPUsAlexander Shiyan2013-12-091-0/+42
| | | | | | | | | | | | | | | | | | This adds i.MX27 and i.MX31 as the next user of the usbmisc driver. Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: imx: avoid unnecessary probe defer every timePeter Chen2013-12-091-1/+1
| | | | | | | | | | | | | | | | The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand, so it is better we load usbmisc_imx first. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: Reallocate regmap only if lpm is detectedChris Ruehl2013-12-091-1/+2
| | | | | | | | | | | | | | | | | | The regmap only needs to reallocate if the hw_read on the CAP register shows lpm is used. Therefore the if() statement check the change. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: remove DEFINE_PCI_DEVICE_TABLE macroJingoo Han2013-12-031-1/+1
| | | | | | | | | | | | | | | | Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro is not preferred. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: host: Only disable the vbus regulator if it is not NULLFabio Estevam2013-12-031-1/+2
|/ | | | | | | | | | | | Commit 40ed51a4b (usb: chipidea: host: add vbus regulator control) introduced a smatch complaint because regulator_disable() is called without checking whether ci->platdata->reg_vbus is not NULL. Fix this by adding the check. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge branch 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds2013-11-131-4/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull DMA mask updates from Russell King: "This series cleans up the handling of DMA masks in a lot of drivers, fixing some bugs as we go. Some of the more serious errors include: - drivers which only set their coherent DMA mask if the attempt to set the streaming mask fails. - drivers which test for a NULL dma mask pointer, and then set the dma mask pointer to a location in their module .data section - which will cause problems if the module is reloaded. To counter these, I have introduced two helper functions: - dma_set_mask_and_coherent() takes care of setting both the streaming and coherent masks at the same time, with the correct error handling as specified by the API. - dma_coerce_mask_and_coherent() which resolves the problem of drivers forcefully setting DMA masks. This is more a marker for future work to further clean these locations up - the code which creates the devices really should be initialising these, but to fix that in one go along with this change could potentially be very disruptive. The last thing this series does is prise away some of Linux's addition to "DMA addresses are physical addresses and RAM always starts at zero". We have ARM LPAE systems where all system memory is above 4GB physical, hence having DMA masks interpreted by (eg) the block layers as describing physical addresses in the range 0..DMAMASK fails on these platforms. Santosh Shilimkar addresses this in this series; the patches were copied to the appropriate people multiple times but were ignored. Fixing this also gets rid of some ARM weirdness in the setup of the max*pfn variables, and brings ARM into line with every other Linux architecture as far as those go" * 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits) ARM: 7805/1: mm: change max*pfn to include the physical offset of memory ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit() ARM: DMA-API: better handing of DMA masks for coherent allocations ARM: 7857/1: dma: imx-sdma: setup dma mask DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks DMA-API: dcdbas: update DMA mask handing DMA-API: dma: edma.c: no need to explicitly initialize DMA masks DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks DMA-API: crypto: remove last references to 'static struct device *dev' DMA-API: crypto: fix ixp4xx crypto platform device support DMA-API: others: use dma_set_coherent_mask() DMA-API: staging: use dma_set_coherent_mask() DMA-API: usb: use new dma_coerce_mask_and_coherent() DMA-API: usb: use dma_set_coherent_mask() DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent() DMA-API: net: octeon: use dma_coerce_mask_and_coherent() DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent() ...
| * DMA-API: usb: use new dma_coerce_mask_and_coherent()Russell King2013-10-311-3/+1
| | | | | | | | | | | | Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * DMA-API: usb: use dma_set_coherent_mask()Russell King2013-10-311-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The correct way for a driver to specify the coherent DMA mask is not to directly access the field in the struct device, but to use dma_set_coherent_mask(). Only arch and bus code should access this member directly. Convert all direct write accesses to using the correct API. Acked-by: Felipe Balbi <balbi@ti.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | usb: chipidea: only get vbus regulator for non-peripheral modePeter Chen2013-10-301-12/+15
| | | | | | | | | | | | | | | | | | | | If the user chooses peripheral mode for this controller, the vbus regulator doesn't need to get, since the host will supply the vbus, it can save one vbus pin for other usage. Signed-off-by: Peter Chen <peter.chen@freescale.com> Tested-by: Frank Li <frank.li@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: host: more enhancement when ci->hcd is NULLPeter Chen2013-10-301-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said: two more things are needed to be done: - If host_start fails, the host_stop should not be called, so we add check that ci->hcd is not NULL. - if the host_start fails at the beginning, we need to consider regulator mismatch issue. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | Merge 3.12-rc6 into usb-next.Greg Kroah-Hartman2013-10-191-2/+4
|\ \ | | | | | | | | | | | | | | | We want those USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb/chipidea: fix oops on memory allocation failureRussell King - ARM Linux2013-10-161-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses the kernel while trying to remove and put the HCD which doesn't exist: WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511 __dma_alloc+0x200/0x240() coherent pool not initialised! Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func Backtrace: [<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c) r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00 [<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c) [<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c) r4:df883a60 r3:df86ad00 [<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40) r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80 [<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240) r3:00000000 r2:c05fda00 [<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0) [<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438) [<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664) [<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180) [<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670 ) r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904 [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) ... ---[ end trace c88ccaf3969e8422 ]--- Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = c0004000 [00000028] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func task: df86ad00 ti: df882000 task.ti: df882000 PC is at usb_remove_hcd+0x10/0x150 LR is at host_stop+0x1c/0x3c pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013 sp : df883b50 ip : df883b78 fp : df883b74 r10: c11f4c54 r9 : c0836450 r8 : df30c400 r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010 r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 2f29404a DAC: 00000015 Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240) Stack: (0xdf883b50 to 0xdf884000) ... Backtrace: [<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c) r6:df2ef410 r5:00000000 r4:df2c3010 [<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20) r5:00000000 r4:df2c3010 [<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670) [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) [<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48) ... ---[ end trace c88ccaf3969e8423 ]--- Fix this so at least we can continue booting and get to a shell prompt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: chipidea: udc: Fix calling spin_lock_irqsave at sleep contextPeter Chen2013-10-121-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixing the below dump: root@freescale ~$ modprobe g_serial g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready BUG: sleeping function called from invalid context at /home/b29397/work/projects/upstream/usb/usb/drivers/base/power/runtime.c:952 in_atomic(): 1, irqs_disabled(): 128, pid: 805, name: modprobe 2 locks held by modprobe/805: #0: (udc_lock){+.+.+.}, at: [<7f000a74>] usb_gadget_probe_driver+0x44/0xb4 [udc_core] #1: (&(&ci->lock)->rlock){......}, at: [<7f033488>] ci_udc_start+0x94/0x110 [ci_hdrc] irq event stamp: 3878 hardirqs last enabled at (3877): [<806b6720>] _raw_spin_unlock_irqrestore+0x40/0x6c hardirqs last disabled at (3878): [<806b6474>] _raw_spin_lock_irqsave+0x2c/0xa8 softirqs last enabled at (3872): [<8002ec0c>] __do_softirq+0x1c8/0x2e8 softirqs last disabled at (3857): [<8002f180>] irq_exit+0xbc/0x110 CPU: 0 PID: 805 Comm: modprobe Not tainted 3.11.0-next-20130910+ #85 [<80016b94>] (unwind_backtrace+0x0/0xf8) from [<80012e0c>] (show_stack+0x20/0x24) [<80012e0c>] (show_stack+0x20/0x24) from [<806af554>] (dump_stack+0x9c/0xc4) [<806af554>] (dump_stack+0x9c/0xc4) from [<8005940c>] (__might_sleep+0xf4/0x134) [<8005940c>] (__might_sleep+0xf4/0x134) from [<803a04a4>] (__pm_runtime_resume+0x94/0xa0) [<803a04a4>] (__pm_runtime_resume+0x94/0xa0) from [<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc]) [<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc]) from [<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core]) [<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core]) from [<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core]) [<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core]) from [<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite]) [<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite]) from [<7f04b168>] (init+0x8c/0xb4 [g_serial]) [<7f04b168>] (init+0x8c/0xb4 [g_serial]) from [<800088e8>] (do_one_initcall+0x108/0x16c) [<800088e8>] (do_one_initcall+0x108/0x16c) from [<8008e518>] (load_module+0x1b00/0x20a4) [<8008e518>] (load_module+0x1b00/0x20a4) from [<8008eba8>] (SyS_init_module+0xec/0x100) [<8008eba8>] (SyS_init_module+0xec/0x100) from [<8000ec40>] (ret_fast_syscall+0x0/0x48) Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: chipidea: udc: Fix spinlock recursion during bus resetPeter Chen2013-10-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After configuration, the host also possible sends bus reset at any time, at such situation, it will trigger below spinlock recursion dump. This commit unlocks the spinlock before calling gadget's disconnect. BUG: spinlock recursion on CPU#0, swapper/0/0 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106 [<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14) [<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc) [<805c143c>] (dump_stack+0x94/0xbc) from [<80282cf8>] (do_raw_spin_lock+0x16c/0x18c) [<80282cf8>] (do_raw_spin_lock+0x16c/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110) [<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4) [<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164) [<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c) [<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168) [<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c) [<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4) [<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c) [<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54) Exception stack(0x8083bf68 to 0x8083bfb0) bf60: 81533b80 00000000 00096234 8001d760 8088e12c 00000000 bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0 bfa0: 8000f138 8000f13c 60000013 ffffffff [<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c) [<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148) [<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318) BUG: spinlock lockup suspected on CPU#0, swapper/0/0 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106 [<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14) [<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc) [<805c143c>] (dump_stack+0x94/0xbc) from [<80282c94>] (do_raw_spin_lock+0x108/0x18c) [<80282c94>] (do_raw_spin_lock+0x108/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110) [<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4) [<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164) [<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c) [<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168) [<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c) [<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4) [<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c) [<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54) Exception stack(0x8083bf68 to 0x8083bfb0) bf60: 81533b80 00000000 00096234 8001d760 8088e12c 00000000 bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0 bfa0: 8000f138 8000f13c 60000013 ffffffff [<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c) [<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148) [<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318) Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | Merge 3.12-rc4 into usb-nextGreg Kroah-Hartman2013-10-071-1/+6
|\| | | | | | | | | | | | | | | | | We want the USB fixes in this branch as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: add Intel Clovertrail pci idDavid Cohen2013-10-041-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | Also clean up the last item of the pci id list to be "cleaner". Signed-off-by: David Cohen <david.a.cohen@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: chipidea: add ci_hdrc_enter_lpm APIPeter Chen2013-10-012-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This API is used to let the PHY enter/leave low power mode. Before the controller going to work(at probe/resume), it needs to let the PHY leave low power mode. After the controller stopping working(at remove/suspend), it needs to let the PHY enter low power mode to save power consumption. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: chipidea: imx: remove PHY operationsPeter Chen2013-10-011-17/+4
| | | | | | | | | | | | | | | | | | | | | | | | Since the PHY operations are moved to core, delete the related code at glue layer. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | usb: chipidea: move PHY operation to corePeter Chen2013-10-012-44/+52
| | | | | | | | | | | | | | | | | | | | | PHY operations are common, so move them to core. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | Merge 3.12-rc3 into usb-nextGreg Kroah-Hartman2013-09-304-4/+8
|\| | | | | | | | | | | | | | | | | We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: USB_CHIPIDEA should depend on HAS_DMAGeert Uytterhoeven2013-09-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If NO_DMA=y: drivers/built-in.o: In function `dma_set_coherent_mask': include/linux/dma-mapping.h:93: undefined reference to `dma_supported' Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: udc: free pending TD at removal procedurePeter Chen2013-09-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a pending TD which is not freed after request finishes, we do this due to a controller bug. This TD needs to be freed when the driver is removed. It prints below error message when unload chipidea driver at current code: "ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy" It indicates the buffer at dma pool are still in use. This commit will free the pending TD at driver's removal procedure, it can fix the problem described above. Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: imx: Add usb_phy_shutdown at probe's error pathPeter Chen2013-09-261-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | If not, the PHY will be active even the controller is not in use. We find this issue due to the PHY's clock refcount is not correct due to -EPROBE_DEFER return after phy's init. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: Fix memleak for ci->hw_bank.regmap when removalPeter Chen2013-09-261-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | It needs to free ci->hw_bank.regmap explicitly since it is not managed resource. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | usb: chipidea: udc: fix the oops after rmmod gadgetPeter Chen2013-09-261-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we rmmod gadget, the ci->driver needs to be cleared. Otherwise, when we plug in usb cable again, the driver will consider gadget is there, and go to enumeration procedure, but in fact, it was removed. ci_hdrc ci_hdrc.0: Connected to host Unable to handle kernel paging request at virtual address 7f02a42c pgd = 80004000 [7f02a42c] *pgd=3f13d811, *pte=00000000, *ppte=00000000 Internal error: Oops: 7 [#1] SMP ARM Modules linked in: usb_f_acm u_serial libcomposite configfs [last unloaded: g_serial] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0+ #42 task: 807dba88 ti: 807d0000 task.ti: 807d0000 PC is at udc_irq+0x8fc/0xea4 LR is at l2x0_cache_sync+0x5c/0x6c pc : [<803de7f4>] lr : [<8001d0f0>] psr: 20000193 sp : 807d1d98 ip : 807d1d80 fp : 807d1df4 r10: af809900 r9 : 808184d4 r8 : 00080001 r7 : 00082001 r6 : afb711f8 r5 : afb71010 r4 : ffffffea r3 : 7f02a41c r2 : afb71010 r1 : 807d1dc0 r0 : afb71068 Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 3f01804a DAC: 00000017 Process swapper/0 (pid: 0, stack limit = 0x807d0238) Stack: (0x807d1d98 to 0x807d2000) 1d80: 00000000 afb71014 1da0: 000040f6 00000000 00000001 00000000 00007530 00000000 afb71010 001dcd65 1dc0: 01000680 00400000 807d1e2c afb71010 0000004e 00000000 00000000 0000004b 1de0: 808184d4 af809900 807d1e0c 807d1df8 803dbc24 803ddf04 afba75c0 0000004e 1e00: 807d1e44 807d1e10 8007a19c 803dbb9c 8108e7e0 8108e7e0 9ceddce0 af809900 1e20: 0000004e 807d0000 0000004b 00000000 00000010 00000000 807d1e5c 807d1e48 1e40: 8007a334 8007a154 af809900 0000004e 807d1e74 807d1e60 8007d3b4 8007a2f0 1e60: 0000004b 807cce3c 807d1e8c 807d1e78 80079b08 8007d300 00000180 807d8ba0 1e80: 807d1eb4 807d1e90 8000eef4 80079aec 00000000 f400010c 807d8ce4 807d1ed8 1ea0: f4000100 96d5c75d 807d1ed4 807d1eb8 80008600 8000eeac 8042699c 60000013 1ec0: ffffffff 807d1f0c 807d1f54 807d1ed8 8000e180 800085dc 807d1f20 00000046 1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010 1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff 1f20: 9cedd275 00000010 00000005 8108f080 8108f080 00000001 807de248 8086bd00 1f40: 807d0000 00000001 807d1f7c 807d1f58 80426af0 80426950 807d0000 00000000 1f60: 808184c0 808184c0 807d8954 805b886c 807d1f8c 807d1f80 8000f294 80426a44 1f80: 807d1fac 807d1f90 8005f110 8000f288 807d1fac 807d8908 805b4748 807dc86c 1fa0: 807d1fbc 807d1fb0 805aa58c 8005f068 807d1ff4 807d1fc0 8077c860 805aa530 1fc0: ffffffff ffffffff 8077c330 00000000 00000000 807bef88 00000000 10c53c7d 1fe0: 807d88d0 807bef84 00000000 807d1ff8 10008074 8077c594 00000000 00000000 Backtrace: [<803ddef8>] (udc_irq+0x0/0xea4) from [<803dbc24>] (ci_irq+0x94/0x14c) [<803dbb90>] (ci_irq+0x0/0x14c) from [<8007a19c>] (handle_irq_event_percpu+0x54/0x19c) r5:0000004e r4:afba75c0 [<8007a148>] (handle_irq_event_percpu+0x0/0x19c) from [<8007a334>] (handle_irq_event+0x50/0x70) [<8007a2e4>] (handle_irq_event+0x0/0x70) from [<8007d3b4>] (handle_fasteoi_irq+0xc0/0x16c) r5:0000004e r4:af809900 [<8007d2f4>] (handle_fasteoi_irq+0x0/0x16c) from [<80079b08>] (generic_handle_irq+0x28/0x38) r5:807cce3c r4:0000004b [<80079ae0>] (generic_handle_irq+0x0/0x38) from [<8000eef4>] (handle_IRQ+0x54/0xb4) r4:807d8ba0 r3:00000180 [<8000eea0>] (handle_IRQ+0x0/0xb4) from [<80008600>] (gic_handle_irq+0x30/0x64) r8:96d5c75d r7:f4000100 r6:807d1ed8 r5:807d8ce4 r4:f400010c r3:00000000 [<800085d0>] (gic_handle_irq+0x0/0x64) from [<8000e180>] (__irq_svc+0x40/0x54) Exception stack(0x807d1ed8 to 0x807d1f20) 1ec0: 807d1f20 00000046 1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010 1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff r7:807d1f0c r6:ffffffff r5:60000013 r4:8042699c [<80426944>] (cpuidle_enter_state+0x0/0xf4) from [<80426af0>] (cpuidle_idle_call+0xb8/0x174) r9:00000001 r8:807d0000 r7:8086bd00 r6:807de248 r5:00000001 r4:8108f080 [<80426a38>] (cpuidle_idle_call+0x0/0x174) from [<8000f294>] (arch_cpu_idle+0x18/0x5c) [<8000f27c>] (arch_cpu_idle+0x0/0x5c) from [<8005f110>] (cpu_startup_entry+0xb4/0x148) [<8005f05c>] (cpu_startup_entry+0x0/0x148) from [<805aa58c>] (rest_init+0x68/0x80) r7:807dc86c [<805aa524>] (rest_init+0x0/0x80) from [<8077c860>] (start_kernel+0x2d8/0x334) [<8077c588>] (start_kernel+0x0/0x334) from [<10008074>] (0x10008074) Code: e59031e0 e51b203c e24b1034 e2820058 (e5933010) ---[ end trace f874b2c5533c04bc ]--- Kernel panic - not syncing: Fatal exception in interrupt Tested-by: Marek Vasut <marex@denx.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: move platform related things to ci_get_platdataPeter Chen2013-09-261-10/+9
| | | | | | | | | | | | | | | | Like vbus, the dr_mode and phy_mode are also got from glue layer's platform data or device node. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | usb: chipidea: udc: Consolidate the call of disconnectPeter Chen2013-09-261-3/+7
| | | | | | | | | | | | | | | | | | | | The udc-core will call gadget's driver->disconnect, so we should avoid calling gadget's disconnect again at ci_udc_stop in case the gadget's unbind free some structs which is still used at gadget's disconnect. Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | chipidea: udc: free pending TD at removal procedurePeter Chen2013-09-261-0/+2
|/ | | | | | | | | | | | | | | There is a pending TD which is not freed after request finishes, we do this due to a controller bug. This TD needs to be freed when the driver is removed. It prints below error message when unload chipidea driver at current code: "ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy" It indicates the buffer at dma pool are still in use. This commit will free the pending TD at driver's removal procedure, it can fix the problem described above. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* USB: chipidea: i.MX: simplify usbmiscSascha Hauer2013-08-143-107/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver handles the chipidea cores and the usbmisc_imx driver handles the noncore registers common to all chipidea cores (but SoC specific). Current flow is: - usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe - ci_hdrc_imx checks if the pointer is valid during probe, if yes calls the functions in the ops pointer. - usbmisc_imx calls back into the ci_hdrc_imx driver to get additional data This is overly complicated and has problems if the drivers are compiled as modules. In this case the usbmisc_imx driver can be unloaded even if the ci_hdrc_imx driver still needs usbmisc functionality. This patch changes this by letting the ci_hdrc_imx driver calling functions from the usbmisc_imx driver. This way the symbol resolving during module load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver. Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx driver, pass the needed data in the first place. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: udc: .pullup is valid only when vbus is therePeter Chen2013-08-141-0/+3
| | | | | | | | | | | For chipidea, the IP must know vbus before the controller begins to run. So the .pullup should only be called when the vbus is there. Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: retire flag CI_HDRC_PULLUP_ON_VBUSPeter Chen2013-08-143-20/+6
| | | | | | | | | | | Currently, the controller only runs when the ci->vbus_active is true. So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer. If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change to update ci->vbus_active. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: udc: fix misuse of REGS_SHARED and PULLUP_ON_VBUS flagsPeter Chen2013-08-141-3/+2
| | | | | | | | | | | | | | | | | | | | | | CI_HDRC_REGS_SHARED stands for the controller registers is shared with other USB drivers, if all USB drivers are at chipidea/, it doesn't needed to be set. CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This flag doesn't need to be set if the vbus is always on for gadget since dp has always pulled up after the gadget has initialized. So, the current code seems to misuse this two flags. - When the gadget initializes, the controller doesn't need to run if it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to shared register. - When the gadget starts (load one gadget module), the controller can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not relate to shared register. Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-14 14:06:45 +0100