summaryrefslogtreecommitdiffstats
path: root/drivers/usb/dwc2/params.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* usb: dwc2: use u32 for DT binding parametersLeo Yan2017-01-121-5/+5
| | | | | | | | | | | | | | | | | | Commit 05ee799f2021 ("usb: dwc2: Move gadget settings into core_params") changes to type u16 for DT binding "g-rx-fifo-size" and "g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the the first two parameters cannot be passed successfully with wrong data format. This is found the data transferring broken on 96boards Hikey. This patch is to change all parameters to u32 type, and verified on Hikey board the DT parameters can pass successfully. [johnyoun: minor rebase] Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Tested-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: gadget: fix default value for gadget-dma-descStefan Wahren2017-01-021-1/+1
| | | | | | | | | | | | | | The current default for gadget DMA descriptor results on bcm2835 in a unnecessary error message: Invalid value 1 for param gadget-dma-desc So fix this by using hw->dma_desc_enable as default value. Fixes: dec4b55677e ("usb: dwc2: gadget: Add descriptor DMA parameter") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: fix default value for DMA supportStefan Wahren2017-01-021-2/+2
| | | | | | | | | | | | | | The current defaults for DMA results on a non-DMA platform in a unnecessary error message: Invalid value 0 for param gadget-dma So fix this by using dma_capable as default value. Fixes: 9962b62f1be ("usb: dwc2: Deprecate g-use-dma binding") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: fix dwc2_get_device_property for u8 and u16Stefan Wahren2017-01-021-12/+0
| | | | | | | | | | | | | | | | | | | According to the Devicetree ePAPR [1] the datatypes u8 and u16 are not defined. So using device_property_read_u16() would result in a partial read of a 32-bit big-endian integer which is not intended. So we better read the complete 32-bit value. This fixes a regression on bcm2835 where the values for g-rx-fifo-size and g-np-tx-fifo-size always read as zero: Invalid value 0 for param g-rx-fifo-size Invalid value 0 for param g-np-tx-fifo-size [1] - http://elinux.org/images/c/cf/Power_ePAPR_APPROVED_v1.1.pdf Fixes: 05ee799f202 ("usb: dwc2: Move gadget settings into core_params") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Do not set host parameter in peripheral modeStefan Wahren2017-01-021-6/+6
| | | | | | | | | | | | | | | Since commit "usb: dwc2: Improve handling of host and device hwparams" the host mode specific hardware parameter aren't initialized in peripheral mode from the register settings anymore. So we better do not set them in this case which avoids the following warnings on bcm2835: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration. 512 invalid for host_perio_tx_fifo_size. Check HW configuration. Fixes: 55e1040e424b ("usb: dwc2: Improve handling of host and device hwparams") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: add amcc,dwc-otg supportChristian Lamparter2016-11-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | This patch adds support for the "amcc,usb-otg" device which is found in the PowerPC Canyonlands' dts. The device definition was added by: commit c89b3458d8cc ("powerpc/44x: Add USB DWC DTS entry to Canyonlands board") but without any driver support as the dwc2 driver wasn't available at that time. Note: The system can't use the generic "snps,dwc2" compatible because of the special ahbcfg configuration. The default GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang when the USB and SATA is used concurrently. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: fixes host_dma logicChristian Lamparter2016-11-181-3/+2
| | | | | | | | | | | | | This patch moves the the host_dma initialization before dwc2_set_param_dma_desc_enable() and dwc2_set_param_dma_desc_fs_enable(). The reason being that both function need it. Fixes: 1205489cee75bf39 ("usb: dwc2: Get host DMA device properties") Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: gadget: Add new core parameter for low speedVardan Mikayelyan2016-11-181-2/+6
| | | | | | | | | | | Added new core param for low speed, which can be used only when SNPSID is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are restricting ep types and providing to upper layer only INTR and CTRL endpoints. Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: gadget: Add IOT device IDs, configure core accordinglyVardan Mikayelyan2016-11-181-1/+8
| | | | | | | | | Add new device IDs for IOT gadget. Done changes in probe to configure core accordingly depending on device ID value. Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Remove reading in of invalid propertyJohn Youn2016-11-181-6/+1
| | | | | | | This property was mistakenly added, then removed, so don't read it in. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: gadget: Add descriptor DMA parameterVahram Aharonyan2016-11-181-0/+6
| | | | | | | | | | Add a parameter for descriptor DMA and set it based on hardware capabilities. This won't actually be used by the gadget until later, when the descriptor DMA code is in place. Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Deprecate g-use-dma bindingJohn Youn2016-11-181-3/+14
| | | | | | | | | This is not needed as the gadget now fully supports DMA and it can autodetect it. This was initially added because gadget DMA mode was only partially implemented so could not be automatically enabled. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Get host DMA device propertiesJohn Youn2016-11-181-30/+18
| | | | | | | | | | The driver will automatically enable host DMA and use it if available. This is consistent with the behavior of all existing platforms. Read in the "snps,host-dma-disable" device property to disable it. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Rename the dma_enable parameter to host_dmaJohn Youn2016-11-181-15/+15
| | | | | | | | Rename it so that it is more consistent with the gadget dma parameter. It only affects host-mode operation so prefix it with "host". Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Move gadget settings into core_paramsJohn Youn2016-11-181-4/+258
| | | | | | | | | | | | | Move the gadget devicetree settings into the core_params structure and document them. Then set and check them in params.c, with the addition of some helper functions, and remove the equivalent code in gadget.c. Because these parameters came from the standalone s3c driver, they have a fixed default value rather than an autodetected one. Preserve and document this behavior to avoid any compatibility issues. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Rename host_rx_fifo_size hardware parameterJohn Youn2016-11-181-5/+5
| | | | | | | | This hardware parameter is not host specific. It also applies to device mode. Drop the "host" from the name to make that clear. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Remove unnecessary prototypesJohn Youn2016-11-181-28/+34
| | | | | | | | | | | | | | Remove the unnecessary prototypes for all the parameter setting functions and declare those functions 'static' in the params.c file. Also remove the duplicate documentation that went along with them. They are already documented as part of the params structure definition. Then move the constants that went along with the prototype into the structure. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Remove dwc2_set_all_params functionJohn Youn2016-11-181-34/+44
| | | | | | | | | Replace this by statically defining a function with defaults, and just assigning it. This will allow us to use parameters of any type and any default value. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Move parameter initialization into params.cJohn Youn2016-11-181-0/+29
| | | | | | | | Consolidate and move all the parameter initialization code from the probe function to params.c. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Declare the core params struct staticallyJohn Youn2016-11-181-34/+34
| | | | | | | | This makes it consistent with the hw_params struct and simplifies the memory management for future refactoring. Fix up usage in all files. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* usb: dwc2: Add params.c fileJohn Youn2016-11-181-0/+1125
Add a params.c file and move all driver parameter code there, including all the static parameter definitions. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-21 01:33:26 +0100