summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/ehci-hub.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Merge 3.1-rc4 into usb-nextGreg Kroah-Hartman2011-08-291-6/+4
|\ | | | | | | | | | | | | This was done to resolve a conflict in this file: drivers/usb/host/xhci-ring.c Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * USB: EHCI: remove usages of hcd->stateAlan Stern2011-08-231-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch (as1483) improves the ehci-hcd driver family by getting rid of the reliance on the hcd->state variable. It has no clear owner and it isn't protected by the usual HCD locks. In its place, the patch adds a new, private ehci->rh_state field to record the state of the root hub. Along the way, the patch removes a couple of lines containing redundant assignments to the state variable. Also, the QUIESCING state simply gets changed to the RUNNING state, because the driver doesn't make any distinction between them. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ↵Wang Zhi2011-08-221-4/+3
|/ | | | | | | | | | | | | | | | ehci_bus_resume(). From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss the action of clearing PORT_RESUME. This will cause unexpected long resume signal on USB bus. Signed-off-by: Wang Zhi <zhi.wang@windriver.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: Fix test mode sequenceBoris Todorov2011-08-081-0/+12
| | | | | | | | | | The sequence to put port in test mode is not complete. According EHCI specification all enabled ports must be put in suspend. Signed-off-by: Boris Todorov <boris.st.todorov@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* EHCI: only power off port if over-current is activeSergei Shtylyov2011-07-081-1/+2
| | | | | | | | | | | | | | | | | | MAX4967 USB power supply chip we use on our boards signals over-current when power is not enabled; once it's enabled, over-current signal returns to normal. That unfortunately caused the endless stream of "over-current change on port" messages. The EHCI root hub code reacts on every over-current signal change with powering off the port -- such change event is generated the moment the port power is enabled, so once enabled the power is immediately cut off. I think we should only cut off power when we're seeing the active over-current signal, so I'm adding such check to that code. I also think that the fact that we've cut off the port power should be reflected in the result of GetPortStatus request immediately, hence I'm adding a PORTSCn register readback after write... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable@kernel.org Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: Move sysfs related bits into ehci-sysfs.cKirill Smelkov2011-07-081-75/+0
| | | | | | | | | | | | | | | | | | | The only sysfs attr implemented so far is "companion" from ehci-hub.c, but in the next patch we are going to add another sysfs file, so prior to that let's structure things and move already-in-there sysfs code to separate file. NOTE: All the code I'm moving into this new file was written by Alan Stern (in 57e06c11 "EHCI: force high-speed devices to run at full speed"; Jan 16 2007), that's why I'm putting Copyright (C) 2007 by Alan Stern there after explicit request from the author. Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: extend ehci-fsl and fsl_udc_core driver for OTG operationAnatolij Gustschin2011-05-031-0/+8
| | | | | | Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Li Yang <leoli@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Mark ehci_adjust_port_wakeup_flags as __maybe_unusedFabio Estevam2011-04-141-1/+1
| | | | | | | | | | | | | Mark ehci_adjust_port_wakeup_flags as __maybe_unused to avoid the following warning when building the ehci-mxc driver: CC drivers/usb/host/ehci-hcd.o drivers/usb/host/ehci-hub.c:130: warning: 'ehci_adjust_port_wakeup_flags' defined but not used Current ehci-mxc driver implementation does not support suspend/resume. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB 3.0 Hub ChangesJohn Youn2011-03-141-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly different hub descriptor than USB 2.0 hubs, with a fixed (rather than variable length) size. Change the USB core's hub descriptor to have a union for the last fields that differ. Change the host controller drivers that access those last fields (DeviceRemovable and PortPowerCtrlMask) to use the union. Translate the new version of the hub port status field into the old version that khubd understands. (Note: we need to fix it to translate the roothub's port status once we stop converting it to USB 2.0 hub status internally.) Add new code to handle link state change status. Send out new control messages that are needed for USB 3.0 hubs, like Set Hub Depth. This patch is a modified version of the original patch submitted by John Youn. It's updated to reflect the removal of the "bitmap" #define, and change the hub descriptor accesses of a couple new host controller drivers. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: "Robert P. J. Day" <rpjday@crashcourse.ca> Cc: Max Vozeler <mvz@vozeler.com> Cc: Tejun Heo <tj@kernel.org> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Rodolfo Giometti <giometti@linux.it> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Lothar Wassmann <LW@KARO-electronics.de> Cc: Olav Kongas <ok@artecdesign.ee> Cc: Martin Fuzzey <mfuzzey@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net>
* USB: Remove bitmap #define from hcd.hSarah Sharp2011-03-141-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using a #define to redefine a common variable name is a bad thing, especially when the #define is in a header. include/linux/usb/hcd.h redefined bitmap to DeviceRemovable to avoid typing a long field in the hub descriptor. This has unintended side effects for files like drivers/usb/core/devio.c that include that file, since another header included after hcd.h has different variables named bitmap. Remove the bitmap #define and replace instances of it in the host controller code. Cleanup the spaces around function calls and square brackets while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: "Robert P. J. Day" <rpjday@crashcourse.ca> Cc: Max Vozeler <mvz@vozeler.com> Cc: Tejun Heo <tj@kernel.org> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Rodolfo Giometti <giometti@linux.it> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Lothar Wassmann <LW@KARO-electronics.de> Cc: Olav Kongas <ok@artecdesign.ee> Cc: Martin Fuzzey <mfuzzey@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net>
* ehci: Check individual port status registers on resumeMatthew Garrett2011-02-251-1/+22
| | | | | | | | | | | If a device plug/unplug is detected on an ATI SB700 USB controller in D3, it appears to set the port status register but not the controller status register. As a result we'll fail to detect the plug event. Check the port status register on resume as well in order to catch this case. Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: stable <stable@kernel.org> [after .39-rc1 is out] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Merge 2.6.38-rc5 into usb-nextGreg Kroah-Hartman2011-02-171-0/+7
|\ | | | | | | | | | | | | This is needed to resolve some merge conflicts that were found in the USB host controller patches, and reported by Stephen Rothwell. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * USB: EHCI: fix scheduling while atomic during suspendYin Kangkai2011-02-041-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is a msleep with spin lock held during ehci pci suspend, which will cause kernel BUG: scheduling while atomic. Fix that. [ 184.139620] BUG: scheduling while atomic: kworker/u:11/416/0x00000002 [ 184.139632] 4 locks held by kworker/u:11/416: [ 184.139640] #0: (events_unbound){+.+.+.}, at: [<c104ddd4>] process_one_work+0x1b3/0x4cb [ 184.139669] #1: ((&entry->work)){+.+.+.}, at: [<c104ddd4>] process_one_work+0x1b3/0x4cb [ 184.139686] #2: (&__lockdep_no_validate__){+.+.+.}, at: [<c127cde3>] __device_suspend+0x2c/0x154 [ 184.139706] #3: (&(&ehci->lock)->rlock){-.-...}, at: [<c132f3d8>] ehci_pci_suspend+0x35/0x7b [ 184.139725] Modules linked in: serio_raw pegasus joydev mrst_gfx(C) battery [ 184.139748] irq event stamp: 52 [ 184.139753] hardirqs last enabled at (51): [<c14fdaac>] mutex_lock_nested+0x258/0x293 [ 184.139766] hardirqs last disabled at (52): [<c14fe7b4>] _raw_spin_lock_irqsave+0xf/0x3e [ 184.139777] softirqs last enabled at (0): [<c10371c1>] copy_process+0x3d2/0x109d [ 184.139789] softirqs last disabled at (0): [< (null)>] (null) [ 184.139802] Pid: 416, comm: kworker/u:11 Tainted: G C 2.6.37-6.3-adaptation-oaktrail #37 [ 184.139809] Call Trace: [ 184.139820] [<c102eeff>] __schedule_bug+0x5e/0x65 [ 184.139829] [<c14fbca5>] schedule+0xac/0xc4c [ 184.139840] [<c11d4845>] ? string+0x37/0x8b [ 184.139853] [<c1044f21>] ? lock_timer_base+0x1f/0x3e [ 184.139863] [<c14fe7da>] ? _raw_spin_lock_irqsave+0x35/0x3e [ 184.139876] [<c1061590>] ? trace_hardirqs_off+0xb/0xd [ 184.139885] [<c14fccdc>] schedule_timeout+0x283/0x2d9 [ 184.139896] [<c104516f>] ? process_timeout+0x0/0xa [ 184.139906] [<c14fcd47>] schedule_timeout_uninterruptible+0x15/0x17 [ 184.139916] [<c104566a>] msleep+0x10/0x16 [ 184.139926] [<c132f316>] ehci_adjust_port_wakeup_flags+0x69/0xf6 [ 184.139937] [<c132f3eb>] ehci_pci_suspend+0x48/0x7b [ 184.139946] [<c1326587>] suspend_common+0x52/0xbb [ 184.139956] [<c1326625>] hcd_pci_suspend+0x26/0x28 [ 184.139967] [<c11e7182>] pci_pm_suspend+0x5f/0xd0 [ 184.139976] [<c127ca3a>] pm_op+0x5d/0xf0 [ 184.139986] [<c127ceac>] __device_suspend+0xf5/0x154 [ 184.139996] [<c127d2c8>] async_suspend+0x16/0x3a [ 184.140006] [<c1058f54>] async_run_entry_fn+0x89/0x111 [ 184.140016] [<c104deb6>] process_one_work+0x295/0x4cb [ 184.140026] [<c1058ecb>] ? async_run_entry_fn+0x0/0x111 [ 184.140036] [<c104e3d0>] worker_thread+0x17f/0x298 [ 184.140045] [<c104e251>] ? worker_thread+0x0/0x298 [ 184.140055] [<c105277f>] kthread+0x64/0x69 [ 184.140064] [<c105271b>] ? kthread+0x0/0x69 [ 184.140075] [<c1002efa>] kernel_thread_helper+0x6/0x1a Signed-off-by: Yin Kangkai <kangkai.yin@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <dbrownell@users.sourceforge.net> CC: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | USB: EHCI: Rearrange create_companion_file() to avoid GCC-4.6 warnings.David Daney2011-02-041-2/+3
|/ | | | | | | | | | | | | | | | | | | In create_companion_file() there is a bogus assignemt to i created for the express purpose of avoiding an ignored return value warning. With pre-release GCC-4.6, this causes a 'set but not used' warning. Kick the problem further down the road by just returning i. All the callers of create_companion_file() ignore its return value, so all is good: o No warnings are issued. o We still subvert the desires of the authors of device_create_file() by ignorning error conditions. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: controller resume should check the root hubAlan Stern2010-08-101-0/+4
| | | | | | | | | | | | | | | | | | | This patch (as1394) adds code to ehci-hcd, ohci-hcd, and uhci-hcd for automatically resuming the root hub when the controller is resumed, if the root hub has a wakeup request pending on some port. During resume from system sleep this doesn't matter, because the root hubs will naturally be resumed along with every other device in the system. However it _will_ matter for runtime PM: If the controller is suspended and a remote wakeup request is received then the controller will autoresume, but we need to ensure that the root hub also autoresumes. Otherwise the wakeup request would be ignored, the controller would go back to sleep, and the cycle would repeat a large number of times (I saw this happen before the patch was written). Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: add do_wakeup parameter for PCI HCD suspendAlan Stern2010-08-101-3/+2
| | | | | | | | | | | | | This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend method used by PCI-based host controller drivers. ehci-hcd in particular needs to know whether or not to enable wakeup when suspending a controller. Although that information is currently available through device_may_wakeup(), when support is added for runtime suspend this will no longer be true. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: convert usb_hcd bitfields into atomic flagsAlan Stern2010-08-101-1/+1
| | | | | | | | | | | | | | | | | | | This patch (as1393) converts several of the single-bit fields in struct usb_hcd to atomic flags. This is for safety's sake; not all CPUs can update bitfield values atomically, and these flags are used in multiple contexts. The flag fields that are set only during registration or removal can remain as they are, since non-atomic accesses at those times will not cause any problems. (Strictly speaking, the authorized_default flag should become atomic as well. I didn't bother with it because it gets changed only via sysfs. It can be done later, if anyone wants.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: EHCI 1.1 addendum: Enable Per-port change detect bitsAlek Du2010-08-101-0/+9
| | | | | | | | | | | This patch will enable Per-port event feature defined in EHCI 1.1 addendum. This feature addresses an issue where HCD is currently required to read and parse PORTSC for all enabled root hub ports. With this patch, the overhead will be reduced. Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: EHCI 1.1 addendum: Basic LPM feature supportAlek Du2010-08-101-0/+5
| | | | | | | | | | | With this patch, the LPM capable EHCI host controller can put device into L1 sleep state which is a mode that can enter/exit quickly, and reduce power consumption. Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com> Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: fix controller wakeup flag settings during suspendAlan Stern2010-05-201-48/+125
| | | | | | | | | | | | | | | | | | | | | | | This patch (as1380) fixes a bug in the wakeup settings for EHCI host controllers. When the controller is suspended, if it isn't enabled for remote wakeup then we have to turn off all the port wakeup flags. Disabling PCI PME# isn't good enough, because some systems (Intel) evidently use alternate wakeup signalling paths. In addition, the patch improves the handling of the Intel Moorestown hardware by performing various power-up and power-down delays just once instead of once for each port (i.e., the delays are moved outside of the port loops). This requires extra code, but the total delay time is reduced. There are also a few additional minor cleanups. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Ondrej Zary <linux@rainbow-software.org> CC: Alek Du <alek.du@intel.com> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: clear PHCD before resumingAlek Du2010-05-201-0/+17
| | | | | | | | | | | | | This is a bug fix for PHCD (phy clock disable) low power feature: After PHCD is set, any write to PORTSC register is illegal, so when resume ports, clear PHCD bit first. Signed-off-by: Alek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: straighten out port feature vs. port status usageAlan Stern2010-05-201-12/+12
| | | | | | | | | | | | | | | This patch (as1349b) clears up the confusion in many USB host controller drivers between port features and port statuses. In mosty cases it's true that the status bit is in the position given by the corresponding feature value, but that's not always true and it's not guaranteed in the USB spec. There's no functional change, just replacing expressions of the form (1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: Increase timeout value for device resetDinh Nguyen2010-04-231-1/+1
| | | | | | | | | | It seems that for USB IP on Freescale MX5x processors, it needs >750 usec for the reset to complete. This change should not hurt any other EHCI hardware. Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci: phy low power mode bug fixingAlek Du2010-02-171-5/+8
| | | | | | | | | | 1. There are two msleep calls inside two spin lock sections, need to unlock and lock again after msleep. 2. Save a extra status reg setting. Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI & UHCI: fix race between root-hub suspend and port resumeAlan Stern2010-01-211-1/+19
| | | | | | | | | | | | | | | This patch (as1321) fixes a problem with EHCI and UHCI root-hub suspends: If the suspend occurs while a port is trying to resume, the resume doesn't finish and simply gets lost. When remote wakeup is enabled, this is undesirable behavior. The patch checks first to see if any port resumes are in progress, and if they are then it fails the root-hub suspend with -EBUSY. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci-hub: Remove redundant ehci->debug checkJason Wessel2009-12-111-1/+1
| | | | | | | | | No need to check ehci->debug twice. Found-by: Sergei Shtylyov sshtylyov@ru.mvista.com Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci-dbgp,ehci: Allow dbpg to work with suspend/resumeJason Wessel2009-09-231-0/+7
| | | | | | | | | | | | | | | In order for the dbgp driver to survive suspend/resume, on every ehci resume operation the debug controller must get re-initialized. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: dbrownell@users.sourceforge.net Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci-dbgp,ehci: Allow early or late use of the dbgp deviceJason Wessel2009-09-231-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | If the EHCI debug port is initialized and in use, the EHCI host controller driver must follow two rules. 1) If the EHCI host driver issues a controller reset, the debug controller driver re-initialization must get called after the reset is completed. 2) The EHCI host driver should ignore any requests to the physical EHCI debug port when the EHCI debug port is in use. The code to check for the debug port was moved from ehci_pci_reinit() to ehci_pci_setup because it must get called prior to ehci_reset() which will clear the debug port registers. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: dbrownell@users.sourceforge.net Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: ensure all watchdog timer events are deleted when suspending usbJon Hunter2009-09-231-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch was previously discussed in the following thread: http://thread.gmane.org/gmane.linux.usb.general/19472/focus=19484 On the OMAP3 device the usbhost controller is in a separate internal power-domain. So when the usbhost is inactive or suspend is called, we can disable clocks and power-down the usbhost to save power. Recently we found that after calling ehci_bus_suspend() and disabling the usbhost clocks we would see the ehci watchdog timer event fire. This was causing a kernel panic because the usbhost controllers clocks were disabled and inside the watchdog timer function the clocks were not being re-enabled, so when the ehci registers were accessed this resulted in a CPU data-abort. To avoid this panic, per recommendation from Alan Stern (see above thread), we make sure any pending timer events (that may have been scheduled by calling ehci_work within the ehci_bus_suspend() function) are deleted before returning. Signed-off-by: Fei Yang <fei.yang@motorola.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: Add Intel Moorestown EHCI controller HOSTPCx extensions and ↵Alek Du2009-09-231-5/+57
| | | | | | | | | | | | | | | | support phy low power mode The Intel Moorestown EHCI controller supports non-standard HOSTPCx register extension. This register controls the LPM behaviour and controls the behaviour of each USB port. Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com> Signed-off-by: Alek Du <alek.du@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: create sysfs companion files directly in the controller deviceGreg Kroah-Hartman2009-06-161-2/+2
| | | | | | | | | The controller device is where we want this sysfs file, especially as the dev pointer is about to go away... Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]Vitaly Bordug2009-01-071-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A published errata for ppc440epx states, that when running Linux with both EHCI and OHCI modules loaded, the EHCI module experiences a fatal error when a high-speed device is connected to the USB2.0, and functions normally if OHCI module is not loaded. There used to be recommendation to use only hi-speed or full-speed devices with specific conditions, when respective module was unloaded. Later, it was observed that ohci suspend is enough to keep things going, and it was turned into workaround, as explained below. Quote from original descriprion: The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In USB 2.0 Host controllers, each EHCI controller has one or more companion controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will contain one or more ports. For each port, only one of the controllers is connected at any one time. In the 440EPx, there is only one OHCI companion controller, and only one USB 2.0 Host port. All ports on an USB 2.0 controller default to the companion controller. If you load only an ohci driver, it will have control of the ports and any deviceplugged in will operate, although high speed devices will be forced to operate at full speed. When an ehci driver is loaded, it explicitly takes control of the ports. If there is a device connected, and / or every time there is a new device connected, the ehci driver determines if the device is high speed or not. If it is high speed, the driver retains control of the port. If it is not, the driver explicitly gives the companion controller control of the port. The is a software workaround that uses Initial version of the software workaround was posted to linux-usb-devel: http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html and later available from amcc.com: http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2 The patch below is generally based on the latter, but reworked to powerpc/of_device USB drivers, and uses a few devicetree inquiries to get rid of (some) hardcoded defines. Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org> Signed-off-by: Stefan Roese <sr@denx.de> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Avoid 20ms delay in EHCI resumeVikram Pandita2009-01-071-3/+15
| | | | | | | | | | | | | | | For function ehci_bus_resume() - Added flag resume_needed No need to wait for 20ms if no port was suspended - Change mdelay to msleep - release and reacquire the spinlock around mdelay Signed-off-by: vikram pandita <vikram.pandita@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: fix remote-wakeup support for ARC/TDI coreAlan Stern2008-10-171-8/+19
| | | | | | | | | | | | | | | | | | This patch (as1147) fixes the remote-wakeup support for EHCI controllers using the ARC/TDI "embedded-TT" core. These controllers turn off the RESUME bit by themselves when a port resume is complete; hence we need to keep separate track of which ports are suspended or in the process of resuming. The patch also makes a couple of small improvements in ehci_irq(), replacing reads of the command register with the value already stored in a local variable. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Thomas Reitmayr <treitmayr@devbase.at> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: fix remote-wakeup regressionAlan Stern2008-05-291-2/+4
| | | | | | | | | | | | | | | | This patch (as1097) fixes a bug in the remote-wakeup handling in ehci-hcd. The driver currently does not keep track of whether the change-suspend feature is enabled for each port; the feature is automatically reset the first time it is read. But recent changes to the hub driver require that the feature be read at least twice in order to work properly. A bit-vector is added for storing the change-suspend feature values. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: suppress unwanted error messagesAlan Stern2008-05-291-0/+10
| | | | | | | | | | | | | | | | | This patch (as1096) fixes an annoying problem: When a full-speed or low-speed device is plugged into an EHCI controller, it fails to enumerate at high speed and then is handed over to the companion controller. But usbcore logs a misleading and unwanted error message when the high-speed enumeration fails. The patch adds a new HCD method, port_handed_over, which asks whether a port has been handed over to a companion controller. If it has, the error message is suppressed. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: use get/put_unaligned_* helpersHarvey Harrison2008-04-291-1/+1
| | | | | | | | | | Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* drivers/usb annotations and fixesAl Viro2008-04-281-1/+1
| | | | | | | | | | | | * endianness annotations * endianness fixes * missing get_unaligned/put_unaligned It's pretty much all over the place, changes to different files are independent. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Serial-parts-Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* USB: fix compile problems in ehci-hcdAlan Stern2008-04-251-2/+2
| | | | | | | | | | | | | | | This patch (as1072) fixes some recently-introduced compile problems that show up in ehci-hcd when CONFIG_PM is turned off. PORT_WAKE_BITS needs to be defined always. ehci_port_power() is called during initialization by all the EHCI variants other than the PCI version, in which it is "defined but not used". So add a call to it. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: HCDs use the do_remote_wakeup flagAlan Stern2008-04-251-10/+7
| | | | | | | | | | | | | | | | | | | | | | | | When a USB device is suspended, whether or not it is enabled for remote wakeup depends on the device_may_wakeup() setting. The setting is then saved in the do_remote_wakeup flag. Later on, however, the device_may_wakeup() value can change because of user activity. So when testing whether a suspended device is or should be enabled for remote wakeup, we should always test do_remote_wakeup instead of device_may_wakeup(). This patch (as1076) makes that change for root hubs in several places. The patch also adjusts uhci-hcd so that when an autostopped controller is suspended, the remote wakeup setting agrees with the value recorded in the root hub's do_remote_wakeup flag. And the patch adjusts ehci-hcd so that wakeup events on selectively suspended ports (i.e., the bus itself isn't suspended) don't turn on the PME# wakeup signal. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci: minor cleanupsDavid Brownell2008-04-251-1/+1
| | | | | | | | | | Minor cleanups to the EHCI code: revision history is what source code repositories should have. Switch to a more standard way to kick in verbose debugging -- don't be EHCI-specific. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: remove CONFIG_USB_PERSIST settingAlan Stern2008-04-251-10/+1
| | | | | | | | | | | This patch (as1047) removes the USB_PERSIST Kconfig option, enabling it permanently. It also prevents the power/persist attribute from being created for hub devices; there's no point in having it since USB-PERSIST is always turned on for hubs. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: carry out port handover during each root-hub resumeAlan Stern2008-04-251-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch (as1044) causes EHCI port handover for non-high-speed devices to occur during every root-hub resume, not just in cases where the controller lost power or was reset. This is necessary because: When some machines go into suspend, they remove power from on-board USB devices while retaining suspend current for USB controllers. The user might well unplug a USB device while the system is suspended and then plug it back in before resuming. A corresponding change is made to the core resume routine; now high-speed root hubs will always be resumed when the system wakes up, even if they were suspended before the system went to sleep. If this weren't done then EHCI port handover wouldn't work, since it is called when the EHCI root hub is resumed. Finally, a comment is added to the hub driver explaining the khubd has to be freezable; if it weren't frozen then it could interfere with port handover. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: another ehci_iaa_watchdog fixDavid Brownell2008-04-031-2/+3
| | | | | | | | | | | | | | | | This patch, suggested by Alan Stern, fixes the hung USB issues on my notebook from suspend/resume cycles. It does so by eliminating some confusion about the internal state machine associated with unlinking from the EHCI async schedule ring, which caused a recent regression: http://bugzilla.kernel.org/show_bug.cgi?id=10345 Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: ehci, remove false clear-reset pathDavid Brownell2008-02-011-5/+1
| | | | | | | | | | | | Some of the "EHCI ports reset forever" problems may be explained by code paths which wrongly flagged resets as complete. This removes two such paths; the ehci_hub_status_data() path should be the only one to have an effect, since it was already properly flagged on the other path. (Issue noted by Minhyoung Kim <a9a9@lge.com>.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: add a short delay to the bus_suspend routineAlan Stern2008-02-011-0/+4
| | | | | | | | | | | This patch (as1031) adds a short delay to the bus-suspend routine in ehci-hcd. Without it some devices disconnect when they should suspend. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: move del_timer_sync calls outside spinlocked regionAlan Stern2008-02-011-1/+2
| | | | | | | | | | | | | This patch (as1030b) moves a del_timer_sync() call outside the scope of a spinlock, where it could cause a deadlock, and adds a new del_timer_sync() call for the new IAA watchdog timer (it was omitted by mistake). Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: add separate IAA watchdog timerAlan Stern2008-02-011-1/+1
| | | | | | | | | | | | | | | | This patch (as1028) was mostly written by David Brownell; I made only a few changes (extra log info and a small bug fix -- which might account for why David's version had to be reverted). It adds a new watchdog timer to the ehci-hcd driver to be used exclusively for detecting lost or missing IAA notifications. Previously a shared timer had been used, which may have led to some problems as reported by Christian Hoffmann. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: force handover port to companion when hub_port_connect_change failsBalaji Rao2008-02-011-24/+44
| | | | | | | | | | This patch hands over the port to the companion when the hub_port_connect_change fails. Signed-off-by: Balaji Rao <balajirrao@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Convert from class_device to device for USB coreTony Jones2008-02-011-10/+13
| | | | | | | | | Convert from class_device to device for drivers/usb/core. Signed-off-by: Tony Jones <tonyj@suse.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-25 11:28:12 +0100