| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf375 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Calao use on there dev kits a FT2232 where the port 0 is used for the JTAG and
port 1 for the UART
They use the same VID and PID as FTDI Chip but they program the manufacturer
name in the eeprom
So use this information to detect it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
| |
Signed-off-by: Gavin.zhu <gavin.kx@qq.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes a NULL pointer deference. A NULL pointer
dereference happens since s5p_ehci->hcd field is not initialized
yet in probe function.
[jg1.han@samsung.com: edit commit message]
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ehci_bus_resume().
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb into usb-linus
* 'for-greg' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb:
usb: musb: gadget: fix error path
usb: gadget: f_phonet: unlock in error case
usb: musb: blackfin: include prefetch head file
usb: musb: tusb6010: fix compilation
usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: musb: cppi: fix build errors due to DBG and missing musb variable
usb: musb: ux500: replace missing DBG with dev_dbg
usb: musb: ux500: set dma config for both src and dst
usb: musb: fix oops on musb_gadget_pullup
usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
usb: gadget: hid: don't STALL when processing a HID Descriptor request
usb: musb: fix Kconfig
usb: musb: tusb6010_omap: fix build failure: error: 'musb' undeclared
usb: gadget: composite: fix bMaxPacketSize for SuperSpeed
usb: gadget: fusb300: remove #if 0 block
usb: gadget: s3c2410_udc: fix unterminated platform_device_id table
|
| | |\ |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In case one "forgot" to load the receiver i.e. doing
|modprobe omap2430
|modprobe musb_hdrc
he ends up with:
|musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|HS USB OTG: no transceiver configured
|musb-hdrc musb-hdrc: musb_init_controller failed with status -19
|(NULL device *): gadget not registered.
|Unable to handle kernel NULL pointer dereference at virtual address 0000001c
|Internal error: Oops: 17 [#1] SMP
|[<c011383c>] (sysfs_find_dirent+0x4/0x60) from [<c01138c0>] (sysfs_get_dirent+0x28/0x78)
|[<c01138c0>] (sysfs_get_dirent+0x28/0x78) from [<c0115b78>] (sysfs_unmerge_group+0x1c/0x90)
|[<c0115b78>] (sysfs_unmerge_group+0x1c/0x90) from [<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c)
|[<c0179ba4>] (dpm_sysfs_remove+0x14/0x3c) from [<c01742f8>] (device_del+0x40/0x1b4)
|[<c01742f8>] (device_del+0x40/0x1b4) from [<c0174478>] (device_unregister+0xc/0x18)
|[<c0174478>] (device_unregister+0xc/0x18) from [<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc])
|[<bf0489b4>] (musb_free+0x24/0x88 [musb_hdrc]) from [<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc])
|[<bf057d18>] (musb_probe+0xb50/0xe3c [musb_hdrc]) from [<c01779c4>] (platform_drv_probe+0x1c/0x24)
The problem is that musb_free() tries to figure out what was
initializued and what wasn't and clean up only the initialized part.
This works well for usb_del_gadget_udc() but device_unregister() can't
deal with it. Therefore we rely on the fact the we always have a parent
device and only then remove the device.
I broke this in 0f91349 ("usb: gadget: convert all users to the new udc
infrastructure")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
After the prefetch/list.h restructure, drivers need to explicitly include
linux/prefetch.h in order to use the prefetch() function. Otherwise, the
current driver fails to build:
drivers/usb/musb/blackfin.c: In function 'musb_write_fifo':
drivers/usb/musb/blackfin.c:43: error: implicit declaration of function
'prefetch'
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
earlier commits have broken compilation of
tusb6010 glue layer, fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Include dma-mapping.h to fix build of the renesas_usbhs driver
| CC drivers/usb/renesas_usbhs/mod_gadget.o
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_map':
| drivers/usb/renesas_usbhs/mod_gadget.c:190: error: implicit declaration of function 'dma_map_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:192: error: implicit declaration of function 'dma_sync_single_for_device'
| drivers/usb/renesas_usbhs/mod_gadget.c:196: error: implicit declaration of function 'dma_mapping_error'
| drivers/usb/renesas_usbhs/mod_gadget.c: In function 'usbhsg_dma_unmap':
| drivers/usb/renesas_usbhs/mod_gadget.c:217: error: implicit declaration of function 'dma_unmap_single'
| drivers/usb/renesas_usbhs/mod_gadget.c:219: error: implicit declaration of function 'dma_sync_single_for_cpu'
| make[5]: *** [drivers/usb/renesas_usbhs/mod_gadget.o] Error 1
| make[4]: *** [drivers/usb/renesas_usbhs] Error 2
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Replace DBG with dev_dbg and fix invalid access of musb->controller.
With this patch cppi_dma builds successfully.
Cc: <stable@kernel.org>
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
ux500_dma.c fail to compile becase DBG has been removed from musb_debug.
Use dev_dbg for all prints.
Cc: stable@vger.kernel.org
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab<mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The dma driver requires both src and dst to be set.
This fix is needed in order to run gadget mass storage.
Patch is verified on snowball.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
CC drivers/usb/musb/tusb6010_omap.o
drivers/usb/musb/tusb6010_omap.c: In function 'tusb_omap_use_shared_dmareq':
drivers/usb/musb/tusb6010_omap.c:92: error: 'musb' undeclared (first use in this function)
drivers/usb/musb/tusb6010_omap.c:92: error: (Each undeclared identifier is reported only once
drivers/usb/musb/tusb6010_omap.c:92: error: for each function it appears in.)
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
| |\ \ \
| |/ /
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For a long time, the xHCI driver has had this note:
/* FIXME: Ignoring zero-length packets, can those happen? */
It turns out that, yes, there are drivers that need to queue zero-length
transfers for isochronous OUT transfers. Without this patch, users will
see kernel hang messages when a driver attempts to enqueue an isochronous
URB with a zero length transfer (because count_isoc_trbs_needed will return
zero for that TD, xhci_td->last_trb will never be set, and updating the
dequeue pointer will cause an infinite loop).
Matěj ran into this issue when using an NI Audio4DJ USB soundcard
with the snd-usb-caiaq driver. See
https://bugzilla.kernel.org/show_bug.cgi?id=40702
Fix count_isoc_trbs_needed() to return 1 for zero-length transfers (thanks
Alan on the math help). Update the various TRB field calculations to deal
with zero-length transfers. We're still transferring one packet with a
zero-length data payload, so the total_packet_count should be 1. The
Transfer Burst Count (TBC) and Transfer Last Burst Packet Count (TLBPC)
fields should be set to zero.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Matěj Laitl <matej@laitl.cz>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
usb_ifnum_to_if() can return NULL if the USB device does not have a
configuration installed (usb_device->actconfig == NULL), or if we can't
find the interface number in the installed configuration. Return an
error instead of crashing.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When a driver tries to cancel an URB, and the host controller is dying,
xhci_urb_dequeue will giveback the URB without removing the xhci_tds
that comprise that URB from the td_list or the cancelled_td_list. This
can cause a race condition between the driver calling URB dequeue and
the stop endpoint command watchdog timer.
If the timer fires on a dying host, and a driver attempts to resubmit
while the watchdog timer has dropped the xhci->lock to giveback a
cancelled URB, URBs may be given back by the xhci_urb_dequeue() function.
At that point, the URB's priv pointer will be freed and set to NULL, but
the TDs will remain on the td_list. This will cause an oops in
xhci_giveback_urb_in_irq() when the watchdog timer attempts to loop
through the endpoints' td_lists, giving back killed URBs.
Make sure that xhci_urb_dequeue() removes TDs from the TD lists and
canceled TD lists before it gives back the URB.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When an isochronous transfer is enqueued, xhci_queue_isoc_tx_prepare()
will ensure that there is enough room on the transfer rings for all of the
isochronous TDs for that URB. However, when xhci_queue_isoc_tx() is
enqueueing individual isoc TDs, the prepare_transfer() function can fail
if the endpoint state has changed to disabled, error, or some other
unknown state.
With the current code, if Nth TD (not the first TD) fails, the ring is
left in a sorry state. The partially enqueued TDs are left on the ring,
and the first TRB of the TD is not given back to the hardware. The
enqueue pointer is left on the TRB after the last successfully enqueued
TD. This means the ring is basically useless. Any new transfers will be
enqueued after the failed TDs, which the hardware will never read because
the cycle bit indicates it does not own them. The ring will fill up with
untransferred TDs, and the endpoint will be basically unusable.
The untransferred TDs will also remain on the TD list. Since the td_list
is a FIFO, this basically means the ring handler will be waiting on TDs
that will never be completed (or worse, dereference memory that doesn't
exist any more).
Change the code to clean up the isochronous ring after a failed transfer.
If the first TD failed, simply return and allow the xhci_urb_enqueue
function to free the urb_priv. If the Nth TD failed, first remove the TDs
from the td_list. Then convert the TRBs that were enqueued into No-op
TRBs. Make sure to flip the cycle bit on all enqueued TRBs (including any
link TRBs in the middle or between TDs), but leave the cycle bit of the
first TRB (which will show software-owned) intact. Then move the ring
enqueue pointer back to the first TRB and make sure to change the
xhci_ring's cycle state to what is appropriate for that ring segment.
This ensures that the No-op TRBs will be overwritten by subsequent TDs,
and the hardware will not start executing random TRBs because the cycle
bit was left as hardware-owned.
This bug is unlikely to be hit, but it was something I noticed while
tracking down the watchdog timer issue. I verified that the fix works by
injecting some errors on the 250th isochronous URB queued, although I
could not verify that the ring is in the correct state because uvcvideo
refused to talk to the device after the first usb_submit_urb() failed.
Ring debugging shows that the ring looks correct, however.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When the isochronous transfer support was introduced, and the xHCI driver
switched to using urb->hcpriv to store an "urb_priv" pointer, a couple of
memory leaks were introduced into the URB enqueue function in its error
handling paths.
xhci_urb_enqueue allocates urb_priv, but it doesn't free it if changing
the control endpoint's max packet size fails or the bulk endpoint is in
the middle of allocating or deallocating streams.
xhci_urb_enqueue also doesn't free urb_priv if any of the four endpoint
types' enqueue functions fail. Instead, it expects those functions to
free urb_priv if an error occurs. However, the bulk, control, and
interrupt enqueue functions do not free urb_priv if the endpoint ring is
NULL. It will, however, get freed if prepare_transfer() fails in those
enqueue functions.
Several of the error paths in the isochronous endpoint enqueue function
also fail to free it. xhci_queue_isoc_tx_prepare() doesn't free urb_priv
if prepare_ring() indicates there is not enough room for all the
isochronous TDs in this URB. If individual isochronous TDs fail to be
queued (perhaps due to an endpoint state change), urb_priv is also leaked.
This argues that the freeing of urb_priv should be done in the function
that allocated it, xhci_urb_enqueue.
This patch looks rather ugly, but refactoring the code will have to wait
because this patch needs to be backported to stable kernels.
This patch should be backported to kernels as old as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When a USB2 port initiate a remote wakeup, software shall ensure that
resume is signaled for at least 20ms, and then write '0' to the PLS field.
According to this, xhci driver do the following things:
1. When receive a remote wakeup event in irq_handler, set the resume_done
value as jiffies + 20ms, and modify rh_timer to poll root hub status at
that time;
2. When receive a GetPortStatus request, if the jiffies is after the
resume_done value, clear the resume signal and resume_done.
However, if usb_port_resume() is called before the rh_timer triggered, it
will indicate the port as Suspend Cleared and skip the clear resume signal
part. The device will fail the usb_get_status request in finish_port_resume(),
and usbcore will try a reset-resume instead. Device will work OK after
reset-resume, but resume_done value is not cleared in this case, and
xhci_bus_suspend() will fail because when it finds a non-zero resume_done
value, it will regard the port as resuming and return -EBUSY.
This causes issue on some platforms that the system fail to suspend
after remote wakeup from suspend by USB2 devices connected to xHCI port.
To fix this issue, report the port status as suspend if the resume is
signaling less that 20ms, and usb_port_resume() will wait 25ms and check
port status again, so xHCI driver can clear the resume signaling and
resume_done value.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix the port U3 status check when Clear PORT_SUSPEND Feature.
The port status should be masked with PORT_PLS_MASK to check if it's in
U3 state.
This should be backported to kernels as old as 2.6.37.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Here is a patch for a new PID (zeitcontrol-device mifare-reader FT232BL(like FT232BM but lead free)).
Signed-off-by: Artur Zimmer <artur128@3dzimmer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| |/ /
| |
| |
| |
| |
| |
| | |
A new device ID pair is added for Sierra Wireless MC8305.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
A new device ID pair is added for Qualcomm Modem present in Sagemcom's HiLo3G module.
Signed-off-by: Vijay Chavan <VijayChavan007@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
ehci_bios_handoff() is marked __devinit, `ehci_dmi_nohandoff_table' should be
marked __devinitconst, not __initconst. This fixes the following section
mismatch:
WARNING: vmlinux.o(.devinit.text+0x4f08): Section mismatch in reference from the function ehci_bios_handoff() to the variable .init.rodata:ehci_dmi_nohandoff_table
The function __devinit ehci_bios_handoff() references a variable __initconst ehci_dmi_nohandoff_table.
If ehci_dmi_nohandoff_table is only used by ehci_bios_handoff then annotate ehci_dmi_nohandoff_table with a matching annotation.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds the product ID of Huawei's Vodafone K4511 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds the product ID of Huawei's Vodafone K4510 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds the product ID of Huawei's Vodafone K3771 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch adds the product ID of Huawei's Vodafone K3770 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on demand
without the intervention of usb_modeswitch. This has the benefit of it becoming
available faster and also ensures that the option driver is not bound to a
network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
needs to be shifted too
the recent addition of the FT232H showed that baudrate was set wrong. See
gmane.linux.usb.general: "[ftdi_sio] FT232H support". With the old code,
the MSB of the 4 encoded fractional divider bits and more important the
clock predivider bits got lost. Adding the FT232H to the code patch were
these bits are shifted solves the problem. I verified baud rates with a
scope now.
I suspect, that the BM device probably needs these bits shifted too. But
there is no predivider bit, so this is not obvious, and a missing MSB of the
encoded fractional divider only shifts the resulting baudrate minimal.
The AM has only 3 bits of encoded fractional divider, so it is not impacted.
I have no BM device to test, so I only added a comment and left the code for
the BM untouched.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The sequence to put port in test mode is not complete.
According EHCI specification all enabled ports must be
put in suspend.
Signed-off-by: Boris Todorov <boris.st.todorov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Even if it's unlikely for this to cause an error,
there is a typo in the code that uses the bitwise-AND
operator instead of the logical one.
Signed-off-by: Ionut Nicu <ionut.nicu@cloudbit.ro>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Connecting the V2M to a Linux host results in a constant stream of
errors spammed to the console, all of the form
sd 1:0:0:0: ioctl_internal_command return code = 8070000
: Sense Key : 0x4 [current]
: ASC=0x0 ASCQ=0x0
The errors appear to be otherwise harmless. Add an unusual_devs entry
which eliminates all of the error messages.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As cpu_is_mx stuff is being used in the driver, header mach/hardware.h
should be explicitly included.
The missing of the header is causing today's linux-next build error
as bleow.
CC drivers/usb/host/ehci-hcd.o
In file included from linux-next/drivers/usb/host/ehci-hcd.c:1190:0:
linux-next/drivers/usb/host/ehci-mxc.c: In function 'ehci_mxc_drv_probe':
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx35'
linux-next/drivers/usb/host/ehci-mxc.c:175:2: error: implicit declaration of function 'cpu_is_mx25'
linux-next/drivers/usb/host/ehci-mxc.c:185:2: error: implicit declaration of function 'cpu_is_mx51'
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
