summaryrefslogtreecommitdiffstats
path: root/drivers/usb (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Merge tag 'usb-3.10-rc2' of ↵Linus Torvalds2013-05-2364-226/+260
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2 The majority of these are USB gadget fixes, but they are all small. Other than that, some USB host controller fixes, and USB serial driver fixes for problems reported with them. Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to be almost impossible to get right for all of the different platforms these days." * tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits) USB: cxacru: potential underflow in cxacru_cm_get_array() USB: ftdi_sio: Add support for Newport CONEX motor drivers USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card usb: ohci: fix goto wrong tag in err case usb: isp1760-if: fix memleak when platform_get_resource fail usb: ehci-s5p: fix memleak when fallback to pdata USB: serial: clean up chars_in_buffer USB: ti_usb_3410_5052: fix chars_in_buffer overhead USB: io_ti: fix chars_in_buffer overhead USB: ftdi_sio: fix chars_in_buffer overhead USB: ftdi_sio: clean up get_modem_status USB: serial: add generic wait_until_sent implementation USB: serial: add wait_until_sent operation USB: set device dma_mask without reference to global data USB: Blacklisted Cinterion's PLxx WWAN Interface usb: option: Add Telewell TW-LTE 4G USB: EHCI: remove bogus #error USB: reset resume quirk needed by a hub USB: usb-stor: realtek_cr: Fix compile error usb, chipidea: fix link error when USB_EHCI_HCD is a module ...
| * USB: cxacru: potential underflow in cxacru_cm_get_array()Dan Carpenter2013-05-201-1/+2
| | | | | | | | | | | | | | | | | | | | The value of "offd" comes off the instance->rcv_buf[] and we used it as the offset into an array. The problem is that we check the upper bound but not for negative values. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: ftdi_sio: Add support for Newport CONEX motor driversGomella, Andrew (NIH/NHLBI) [F]2013-05-172-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Here are two more devices that use FTDI USB-to-serial chips with new product ID's. The devices are the Newport Conex-AGP and Conex-CC motor controllers. (http://www.newport.com/CONEX-AGP-Integrated-Piezo-Motor-Rotation-Stages-/987623/1033/info.aspx) (http://www.newport.com/CONEX-CC-DC-Servo-Controller-Actuators/934114/1033/info.aspx) usb-devices command yields: P: Vendor=104d ProdID=3002 Rev=06.00 S: Manufacturer=Newport S: Product=CONEX-CC as well as P: Vendor=104d ProdID=3006 Rev=06.00 S: Manufacturer=Newport S: Product=CONEX-AGP Signed-off-by: Andrew Gomella <andrew.gomella@nih.gov> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN cardDan Williams2013-05-171-0/+2
| | | | | | | | | | | | | | | | A rebranded Novatel E371 for AT&T's LTE bands. Cc: stable <stable@vger.kernel.org> Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: ohci: fix goto wrong tag in err caseLibo Chen2013-05-171-23/+23
| | | | | | | | | | | | | | | | fix goto wrong tag in usb_hcd_nxp_probe Signed-off-by: Libo Chen <libo.chen@huawei.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: isp1760-if: fix memleak when platform_get_resource failLibo Chen2013-05-171-1/+3
| | | | | | | | | | | | | | When platform_get_resource fail, we should release_mem_region Signed-off-by: Libo Chen <libo.chen@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: ehci-s5p: fix memleak when fallback to pdataLibo Chen2013-05-171-0/+1
| | | | | | | | | | | | | | When devm_usb_get_phy fail, we should free hcd Signed-off-by: Libo Chen <libo.chen@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: serial: clean up chars_in_bufferJohan Hovold2013-05-171-9/+2
| | | | | | | | | | | | | | | | | | No need to grab disconnect mutex in chars_in_buffer now that no sub-driver is or should be querying hardware buffers anymore. (They should use wait_until_sent.) Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: ti_usb_3410_5052: fix chars_in_buffer overheadJohan Hovold2013-05-171-8/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new generic usb-serial wait_until_sent implementation to wait for hardware buffers to drain. This removes the need to check the hardware buffers in chars_in_buffer and thus removes the overhead introduced by commit 2c992cd73 ("USB: ti_usb_3410_5052: query hardware-buffer status in chars_in_buffer") without breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak and close). Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: io_ti: fix chars_in_buffer overheadJohan Hovold2013-05-171-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new generic usb-serial wait_until_sent implementation to wait for hardware buffers to drain. This removes the need to check the hardware buffers in chars_in_buffer and thus removes the overhead introduced by commit 263e1f9f ("USB: io_ti: query hardware-buffer status in chars_in_buffer") without breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak and close). Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: ftdi_sio: fix chars_in_buffer overheadJohan Hovold2013-05-171-14/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new generic usb-serial wait_until_sent implementation to wait for hardware buffers to drain. This removes the need to check the hardware buffers in chars_in_buffer and thus removes the overhead introduced by commit 6f602912 ("usb: serial: ftdi_sio: Add missing chars_in_buffer function") without breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak and close). Reported-by: Stas Sergeev <stsp@list.ru> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: ftdi_sio: clean up get_modem_statusJohan Hovold2013-05-171-5/+4
| | | | | | | | | | | | | | Use usb-serial port rather than tty as argument to get_modem_status. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: serial: add generic wait_until_sent implementationJohan Hovold2013-05-172-0/+33
| | | | | | | | | | | | | | | | | | | | | | Add generic wait_until_sent implementation which polls for empty hardware buffers using the new port-operation tx_empty. The generic implementation will be used for all sub-drivers that implement tx_empty but does not define wait_until_sent. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: serial: add wait_until_sent operationJohan Hovold2013-05-171-0/+17
| | | | | | | | | | | | | | | | Add wait_until_sent operation which can be used to wait for hardware buffers to drain. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: set device dma_mask without reference to global dataStephen Warren2013-05-1714-52/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many USB host drivers contain code such as: if (!pdev->dev.dma_mask) pdev->dev.dma_mask = &tegra_ehci_dma_mask; ... where tegra_ehci_dma_mask is a global. I suspect this code originated in commit 4a53f4e "USB: ehci-tegra: add probing through device tree" and was simply copied everywhere else. This works fine when the code is built-in, but can cause a crash when the code is in a module. The first module load sets up the dma_mask pointer, but if the module is removed and re-inserted, the value is now non-NULL, and hence is not updated to point at the new location, and hence points at a stale location within the previous module load address, which in turn causes a crash if the pointer is de-referenced. The simplest way of solving this seems to be to copy the code from ehci-platform.c, which uses the coherent_dma_mask as the target for the dma_mask pointer. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: Blacklisted Cinterion's PLxx WWAN InterfaceSchemmel Hans-Christoph2013-05-171-4/+5
| | | | | | | | | | | | | | | | | | | | /drivers/usb/serial/option.c: Blacklisted Cinterion's PLxx WWAN Interface (USB Interface 4), because it will be handled by QMI WWAN driver. Product IDs renamed. Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: option: Add Telewell TW-LTE 4GTeppo Kotilainen2013-05-171-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Information from driver description files: diag: VID_19D2&PID_0412&MI_00 nmea: VID_19D2&PID_0412&MI_01 at: VID_19D2&PID_0412&MI_02 modem: VID_19D2&PID_0412&MI_03 net: VID_19D2&PID_0412&MI_04 Signed-off-by: Teppo Kotilainen <qubit303@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: EHCI: remove bogus #errorArnd Bergmann2013-05-171-17/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EHCI host controller driver can be built standalone now, without enabling any of the available bus glue drivers, so there is not really a reason to error out here: drivers/usb/host/ehci-hcd.c:1303:2: error: #error "missing bus glue for ehci-hcd" #error "missing bus glue for ehci-hcd" The alternative would be to change the Kconfig code to build the ehci-hcd module only if any of the symbols below are in fact enabled. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: reset resume quirk needed by a hubOliver Neukum2013-05-171-0/+3
| | | | | | | | | | | | | | | | Werner Fink has reported problems with this hub. Signed-off-by: Oliver Neukum <oliver@neukum.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: usb-stor: realtek_cr: Fix compile errorWei WANG2013-05-171-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | To fix the compile error when CONFIG_PM_RUNTIME is not enabled, move the declaration of us out of CONFIG_REALTEK_AUTOPM macro in rts51x_chip. drivers/usb/storage/realtek_cr.c: In function 'realtek_cr_destructor': drivers/usb/storage/realtek_cr.c:942:11: error: 'struct rts51x_chip' has no member named 'us' Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Reported-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb, chipidea: fix link error when USB_EHCI_HCD is a moduleDavid Rientjes2013-05-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes link error when USB_EHCI_HCD=m and USB_CHIPIDEA_HOST=y: drivers/built-in.o: In function `ci_hdrc_host_init': drivers/usb/chipidea/host.c:104: undefined reference to `ehci_init_driver' as a result of commit 09f6ffde2ece ("USB: EHCI: fix build error by making ChipIdea host a normal EHCI driver"). Cc: stable@vger.kernel.org [v3.7+] Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: remove remaining instances of USB_SUSPENDAlan Stern2013-05-155-6/+6
| | | | | | | | | | | | | | | | | | | | Commit 84ebc10294a3d7be4c66f51070b7aedbaa24de9b (USB: remove CONFIG_USB_SUSPEND option) failed to remove all of the usages of USB_SUSPEND throughout the kernel. This patch (as1677) removes the remaining instances of that symbol. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: OHCI: fix logic for scheduling isochronous URBsAlan Stern2013-05-151-14/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The isochronous scheduling logic in ohci-hcd has a bug. The calculation for skipping TDs that are too late should be carried out only in the !URB_ISO_ASAP case. When URB_ISO_ASAP is set, the URB is pushed back so that none of the TDs are too late, which would cause the calculation to overflow. The patch also fixes the calculation to avoid overflow in the case where the frame value wraps around. This should be applied to -stable kernels going back to 3.8. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: fix latency in uhci-hcd and ohci-hcdAlan Stern2013-05-152-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commits c44b225077bb1fb25ed5cd5c4f226897b91bedd4 (UHCI: implement new semantics for URB_ISO_ASAP) and 6a41b4d3fe8cd4cc95181516fc6fba7b1747a27c (OHCI: implement new semantics for URB_ISO_ASAP) increased the latency for isochronous URBs in uhci-hcd and ohci-hcd respectively to 2 milliseconds, in an attempt to avoid underruns. It turns out that not only was this unnecessary -- 1-ms latency works okay -- it also causes problems with certain application loads such as real-time audio. This patch changes the latency for both drivers back to 1 ms. This should be applied to -stable kernels going back to 3.8. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Joe Rayhawk <jrayhawk@fairlystable.org> CC: Clemens Ladisch <clemens@ladisch.de> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: UHCI: fix for suspend of virtual HP controllerAlan Stern2013-05-151-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HP's virtual UHCI host controller takes a long time to suspend (several hundred microseconds), even when no devices are attached. This provokes a warning message from uhci-hcd in the auto-stop case. To prevent this from happening, this patch adds a test to avoid performing an auto-stop when the wait_for_hp quirk flag is set. The controller will still suspend through the normal runtime PM mechanism. And since that pathway includes a 1-ms delay, the slowness of the virtual hardware won't matter. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: ZhenHua <zhen-hual@hp.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: fix Kconfig logic for USB_UHCI_HCDAlan Stern2013-05-151-12/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig settings for uhci-hcd are too permissive; they allow the driver to be built without any bus-glue modules configured (USB_UHCI_HCD enabled, PCI disabled, SPARC_LEON disabled, ARCH_VT8500 enabled, and USB_UHCI_PLATFORM disabled). This patch fixes the problem by rearranging the dependencies. Now the platform-dependent config options don't depend on USB_UHCI_HCD; instead it depends on them. Furthermore, there is no user-selectable choice as to which glue modules will be built. If USB_UHCI_HCD is enabled then all applicable bus glues will be built. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * USB: xHCI: override bogus bulk wMaxPacketSize valuesAlan Stern2013-05-151-8/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch shortens the logic in xhci_endpoint_init() by moving common calculations involving max_packet and max_burst outside the switch statement, rather than repeating the same code in multiple case-specific statements. It also replaces two usages of max_packet which were clearly intended to be max_burst all along. More importantly, it compensates for a common bug in high-speed bulk endpoint descriptors. In many devices there is a bulk endpoint having a wMaxPacketSize value smaller than 512, which is forbidden by the USB spec. Some xHCI controllers can't handle this and refuse to accept the endpoint. This patch changes the max_packet value to 512, which allows the controller to use the endpoint properly. In practice the bogus maxpacket size doesn't matter, because none of the transfers sent via these endpoints are longer than the maxpacket value anyway. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: "Aurélien Leblond" <blablack@gmail.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * usb: otg: mxs-phy: add missing type to usb_phyMichael Grzeschik2013-05-151-0/+1
| | | | | | | | | | | | | | | | The mxs-phy is missing the phy.type property, why the usb_get_phy helper function won't be able to find it. This patch adds this missing property. Signed-off-by: Michael Grzeschik <mgr@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: remove CONFIG_USB_OTG_UTILS once morePaul Bolle2013-05-152-2/+0
| | | | | | | | | | | | | | | | | | | | The Kconfig symbol USB_OTG_UTILS was removed in the v3.10 merge window, in commit fd89149875 ("usb: phy: remove CONFIG_USB_OTG_UTILS"). But that symbol popped up again in a few places. Remove it there too. Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: s3c-hsotg: pass 'struct usb_request *' to ↵Jingoo Han2013-05-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | usb_gadget_unmap_request() 'struct usb_request *' should be passed to usb_gadget_unmap_request(), as the second argument; however, 'struct s3c_hsotg_req *' is used. Fixed build warnings as below: drivers/usb/gadget/s3c-hsotg.c: In function 's3c_hsotg_unmap_dma': drivers/usb/gadget/s3c-hsotg.c:440:2: warning: passing argument 2 of 'usb_gadget_unmap_request' from incompatible pointer type [enabled by default] include/linux/usb/gadget.h:961:13: note: expected 'struct usb_request *' but argument is of type 'struct s3c_hsotg_req *' drivers/usb/gadget/s3c-hsotg.c:434:22: warning: unused variable 'req' [-Wunused-variable] Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: Fix NULL pointer exception during usb_get_phyRobert Jarzmik2013-05-153-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Upon initialisation (driver probe) a NULL pointer exception is triggered. This is due to lack of initialisation of device field in phy structure, which is used by phy framework in usb_get_phy(). Fix it by initialising the device field. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: don't check resource with devm_ioremap_resourceWolfram Sang2013-05-154-20/+0
| | | | | | | | | | | | | | | | | | devm_ioremap_resource does sanity checks on the given resource. No need to duplicate this in the driver. Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: don't check resource with devm_ioremap_resourceWolfram Sang2013-05-151-10/+0
| | | | | | | | | | | | | | | | | | devm_ioremap_resource does sanity checks on the given resource. No need to duplicate this in the driver. Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: dwc3: Fix compilation break when building with USB_DWC3_DUAL_ROLE=yVivek Gautam2013-05-151-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit: 388e5c5 usb: dwc3: remove dwc3 dependency on host AND gadget breaks compilation when USB=y, USB_GADGET=m, USB_DWC3=y and USB_DWC3_DUAL_ROLE=y. drivers/built-in.o: In function `dwc3_gadget_giveback': drivers/usb/dwc3/gadget.c:271: undefined reference to `usb_gadget_unmap_request' drivers/built-in.o: In function `__dwc3_gadget_kick_transfer': drivers/usb/dwc3/gadget.c:1005: undefined reference to `usb_gadget_unmap_request' drivers/built-in.o: In function `__dwc3_gadget_ep_queue': drivers/usb/dwc3/gadget.c:1073: undefined reference to `usb_gadget_map_request' drivers/built-in.o: In function `dwc3_gadget_reset_interrupt': drivers/usb/dwc3/gadget.c:2165: undefined reference to `usb_gadget_set_state' drivers/built-in.o: In function `dwc3_gadget_init': drivers/usb/dwc3/gadget.c:2647: undefined reference to `usb_add_gadget_udc' drivers/built-in.o: In function `dwc3_gadget_exit': drivers/usb/dwc3/gadget.c:2681: undefined reference to `usb_del_gadget_udc' drivers/built-in.o: In function `__dwc3_ep0_do_control_data': drivers/usb/dwc3/ep0.c:929: undefined reference to `usb_gadget_map_request' drivers/usb/dwc3/ep0.c:906: undefined reference to `usb_gadget_map_request' drivers/built-in.o: In function `dwc3_ep0_set_config': drivers/usb/dwc3/ep0.c:575: undefined reference to `usb_gadget_set_state' drivers/built-in.o: In function `dwc3_ep0_set_address': drivers/usb/dwc3/ep0.c:520: undefined reference to `usb_gadget_set_state' drivers/usb/dwc3/ep0.c:522: undefined reference to `usb_gadget_set_state' drivers/built-in.o: In function `dwc3_ep0_set_config': drivers/usb/dwc3/ep0.c:556: undefined reference to `usb_gadget_set_state' Making changes similar to patch: 71a5e61 usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module Let us limit the DWC3 mode to depend on corresponding usb-subsystem and USB_DWC3. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: fix error return code in configfs_composite_bind()Wei Yongjun2013-05-151-2/+6
| | | | | | | | | | | | | | | | | | | | Fix to return a negative error code in the go through all configs error handling case instead of 0(usb_add_function() will overwrite ret to 0). Also use error code from usb_gstrings_attach() in all strings init error case instead of -EINVAL. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: dummy_hcd: fix error return code in init()Wei Yongjun2013-05-151-1/+3
| | | | | | | | | | | | | | | | | | | | Fix to return -ENOMEM in the kzalloc() error handling case instead of 0(following platform_device_add_data() will overwrite it to 0), as done elsewhere in this function. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: fusb300_udc: fix error return code in fusb300_probe()Wei Yongjun2013-05-151-1/+3
| | | | | | | | | | | | | | | | Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: m66592-udc: fix error return code in m66592_probe()Wei Yongjun2013-05-151-1/+3
| | | | | | | | | | | | | | | | Fix to return -ENOMEM in the request alloc error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: r8a66597-udc: fix error return code in r8a66597_probe()Wei Yongjun2013-05-151-1/+3
| | | | | | | | | | | | | | | | Fix to return -ENOMEM in the request alloc error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: s3c2410_udc: fix error return code in s3c2410_udc_probe()Wei Yongjun2013-05-151-0/+1
| | | | | | | | | | | | | | | | | | Fix to return a negative error code in the gpio_to_irq() error handling case instead of 0, as done elsewhere in this function. Reviewed-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: musb: dsps: fix error return code in dsps_create_musb_pdev()Wei Yongjun2013-05-151-0/+1
| | | | | | | | | | | | | | | | Fix to return -ENOMEM in the devm_kzalloc() error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: nop: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: mxs-usb: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: mv-usb: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-3/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Chao Xie <chao.xie@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: gpio-vbus-usb: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: phy: ab8500-usb: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: s3c2410_udc: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: pxa25x_udc: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-1/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: imx_udc: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Darius Augulis <augulis.darius@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
| * usb: gadget: f_uac2: Remove redundant platform_set_drvdata()Sachin Kamat2013-05-151-2/+0
| | | | | | | | | | | | | | | | | | | | Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-25 00:42:35 +0100