summaryrefslogtreecommitdiffstats
path: root/drivers (follow)
Commit message (Collapse)AuthorAgeFilesLines
* dm ioctl: constify ioctl lookup tableEric Biggers2017-08-281-1/+1
| | | | | | | | Constify the lookup table for device-mapper ioctls so that it is placed in .rodata. Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm: constify argument arraysEric Biggers2017-08-289-17/+18
| | | | | | | | | | | The arrays of 'struct dm_arg' are never modified by the device-mapper core, so constify them so that they are placed in .rodata. (Exception: the args array in dm-raid cannot be constified because it is allocated on the stack and modified.) Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm integrity: count and display checksum failuresMikulas Patocka2017-08-281-2/+8
| | | | | | | | | This changes DM integrity to count the number of checksum failures and report the counter in response to STATUSTYPE_INFO request (via 'dmsetup status'). Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm integrity: optimize writing dm-bufio buffers that are partially changedMikulas Patocka2017-08-283-29/+77
| | | | | | | | | | | | Rather than write the entire dm-bufio buffer when only a subset is changed, improve dm-bufio (and dm-integrity) by only writing the subset of the buffer that changed. Update dm-integrity to make use of dm-bufio's new dm_bufio_mark_partial_buffer_dirty() interface. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm rq: do not update rq partially in each ending bioMing Lei2017-08-282-11/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | We don't need to update the original dm request partially when ending each cloned bio: just update original dm request once when the whole cloned request is finished. This still allows full support for partial completion because a new 'completed' counter accounts for incremental progress as the clone bios complete. Partial request update can be a bit expensive, so we should try to avoid it, especially because it is run in softirq context. Avoiding all the partial request updates fixes both hard lockup and soft lockups that were easily reproduced while running Laurence's test[1] on IB/SRP. BTW, after d4acf3650c7c ("block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time"), we need to make the test more aggressive for reproducing the lockup: 1) run hammer_write.sh 32 or 64 concurrently. 2) write 8M each time [1] https://marc.info/?l=linux-block&m=150220185510245&w=2 Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm rq: make dm-sq requeuing behavior consistent with dm-mq behaviorBart Van Assche2017-08-281-4/+5
| | | | | | | | | | DM_MAPIO_DELAY_REQUEUE causes dm-mq to requeue after a delay but causes dm-sq to requeue immediately. Make the behavior of dm-sq consistent with that of dm-mq. Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm mpath: complain about unsupported __multipath_map_bio() return valuesBart Van Assche2017-08-281-0/+4
| | | | | | | | WARN_ONCE() if __multipath_map_bio() returns an unsupported return value. Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm mpath: avoid that building with W=1 causes gcc 7 to complain about ↵Bart Van Assche2017-08-281-0/+1
| | | | | | | | fall-through Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm mpath: do not lock up a CPU with requeuing activityBart Van Assche2017-08-281-1/+0
| | | | | | | | | | | | | | | When using the block layer in single queue mode, get_request() returns ERR_PTR(-EAGAIN) if the queue is dying and the REQ_NOWAIT flag has been passed to get_request(). Avoid that the kernel reports soft lockup complaints in this case due to continuous requeuing activity. Fixes: 7083abbbf ("dm mpath: avoid that path removal can trigger an infinite loop") Cc: stable@vger.kernel.org Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Tested-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm: fix printk() rate limiting codeBart Van Assche2017-08-281-10/+0
| | | | | | | | | | | | Using the same rate limiting state for different kinds of messages is wrong because this can cause a high frequency message to suppress a report of a low frequency message. Hence use a unique rate limiting state per message type. Fixes: 71a16736a15e ("dm: use local printk ratelimit") Cc: stable@vger.kernel.org Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm mpath: retry BLK_STS_RESOURCE errorsBart Van Assche2017-08-281-1/+0
| | | | | | | | | | | Retry requests instead of failing them if an out-of-memory error occurs or the block driver below dm-mpath is busy. This restores the v4.12 behavior of noretry_error(), namely that -ENOMEM results in a retry. Fixes: 2a842acab109 ("block: introduce new block status code type") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* dm: fix the second dec_pending() argument in __split_and_process_bio()Bart Van Assche2017-08-281-1/+1
| | | | | | | | | | Detected by sparse. Fixes: 4e4cbee93d56 ("block: switch bios to blk_status_t") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* Merge tag 'iommu-fixes-v4.13-rc6' of ↵Linus Torvalds2017-08-283-14/+26
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull IOMMU fix from Joerg Roedel: "Another fix, this time in common IOMMU sysfs code. In the conversion from the old iommu sysfs-code to the iommu_device_register interface, I missed to update the release path for the struct device associated with an IOMMU. It freed the 'struct device', which was a pointer before, but is now embedded in another struct. Freeing from the middle of allocated memory had all kinds of nasty side effects when an IOMMU was unplugged. Unfortunatly nobody unplugged and IOMMU until now, so this was not discovered earlier. The fix is to make the 'struct device' a pointer again" * tag 'iommu-fixes-v4.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu: Fix wrong freeing of iommu_device->dev
| * iommu: Fix wrong freeing of iommu_device->devJoerg Roedel2017-08-153-14/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The struct iommu_device has a 'struct device' embedded into it, not as a pointer, but the whole struct. In the conversion of the iommu drivers to use struct iommu_device it was forgotten that the relase function for that struct device simply calls kfree() on the pointer. This frees memory that was never allocated and causes memory corruption. To fix this issue, use a pointer to struct device instead of embedding the whole struct. This needs some updates in the iommu sysfs code as well as the Intel VT-d and AMD IOMMU driver. Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Fixes: 39ab9555c241 ('iommu: Add sysfs bindings for struct iommu_device') Cc: stable@vger.kernel.org # >= v4.11 Signed-off-by: Joerg Roedel <jroedel@suse.de>
* | Merge tag 'char-misc-4.13-rc7' of ↵Linus Torvalds2017-08-281-1/+1
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc fix from Greg KH: "Here is a single misc driver fix for 4.13-rc7. It resolves a reported problem in the Android binder driver due to previous patches in 4.13-rc. It's been in linux-next with no reported issues" * tag 'char-misc-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: ANDROID: binder: fix proc->tsk check.
| * | ANDROID: binder: fix proc->tsk check.Martijn Coenen2017-08-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit c4ea41ba195d ("binder: use group leader instead of open thread")' was incomplete and didn't update a check in binder_mmap(), causing all mmap() calls into the binder driver to fail. Signed-off-by: Martijn Coenen <maco@android.com> Tested-by: John Stultz <john.stultz@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | Merge tag 'staging-4.13-rc7' of ↵Linus Torvalds2017-08-2810-43/+104
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/iio fixes from Greg KH: "Here are few small staging driver fixes, and some more IIO driver fixes for 4.13-rc7. Nothing major, just resolutions for some reported problems. All of these have been in linux-next with no reported problems" * tag 'staging-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: iio: magnetometer: st_magn: remove ihl property for LSM303AGR iio: magnetometer: st_magn: fix status register address for LSM303AGR iio: hid-sensor-trigger: Fix the race with user space powering up sensors iio: trigger: stm32-timer: fix get trigger mode iio: imu: adis16480: Fix acceleration scale factor for adis16480 PATCH] iio: Fix some documentation warnings staging: rtl8188eu: add RNX-N150NUB support Revert "staging: fsl-mc: be consistent when checking strcmp() return" iio: adc: stm32: fix common clock rate iio: adc: ina219: Avoid underflow for sleeping time iio: trigger: stm32-timer: add enable attribute iio: trigger: stm32-timer: fix get/set down count direction iio: trigger: stm32-timer: fix write_raw return value iio: trigger: stm32-timer: fix quadrature mode get routine iio: bmp280: properly initialize device for humidity reading
| * \ \ Merge tag 'fixes-for-4.13b' of ↵Greg Kroah-Hartman2017-08-208-40/+100
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: Second set of IIO fixes for the 4.13 cycle. Given the late stage of this series, some more involved fixes have been held back for the upcoming merge window. The hid-sensor issue has been causing problems for a long time so it is great to have that one finally fixed! No more bug reports for the userspace guys (well about that anyway). * documentation - some warning fixes due to missing colons in kernel-doc. * adis16480 - fix accel scale factor. * bmp280 - properly initialize the device for humidity readings - without this the humidity readings may be skipped and a magic value of 0x8000 returned. * hid-sensor-strigger - fix a race with user space when powering up the sensor. * ina291 - Avoid an underflow for the sleeping time as a result of supporting the fastest rates. * st-magnetometer - Fix the status register address for hte LSM303AGR, - Remove the ihl property for LSM303AGR as the sensor doesn't support active low for the dataready line. * stm32-adc - Fix use of a common clock rate. * stm32-timer - fix the quadrature mode get routine to account for the magic 0 value. set on boot. - fix the return value of write_raw, - fix the get/set down count direction as the enum value was not being converted to the relevant bit field, - add an enable attribute to actually turn it on when in encoder mode, - missing mask when reading the trigger mode.
| | * | | iio: magnetometer: st_magn: remove ihl property for LSM303AGRLorenzo Bianconi2017-08-201-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove IRQ active low support for LSM303AGR since the sensor does not support that capability for data-ready line Fixes: a9fd053b56c6 (iio: st_sensors: support active-low interrupts) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: magnetometer: st_magn: fix status register address for LSM303AGRLorenzo Bianconi2017-08-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: hid-sensor-trigger: Fix the race with user space powering up sensorsSrinivas Pandruvada2017-08-201-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It has been reported for a while that with iio-sensor-proxy service the rotation only works after one suspend/resume cycle. This required a wait in the systemd unit file to avoid race. I found a Yoga 900 where I could reproduce this. The problem scenerio is: - During sensor driver init, enable run time PM and also set a auto-suspend for 3 seconds. This result in one runtime resume. But there is a check to avoid a powerup in this sequence, but rpm is active - User space iio-sensor-proxy tries to power up the sensor. Since rpm is active it will simply return. But sensors were not actually powered up in the prior sequence, so actaully the sensors will not work - After 3 seconds the auto suspend kicks If we add a wait in systemd service file to fire iio-sensor-proxy after 3 seconds, then now everything will work as the runtime resume will actually powerup the sensor as this is a user request. To avoid this: - Remove the check to match user requested state, this will cause a brief powerup, but if the iio-sensor-proxy starts immediately it will still work as the sensors are ON. - Also move the autosuspend delay to place when user requested turn off of sensors, like after user finished raw read or buffer disable Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Bastien Nocera <hadess@hadess.net> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: trigger: stm32-timer: fix get trigger modeFabrice Gasnier2017-08-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix reading trigger mode, when other bit-fields are set. SMCR register value must be masked to read SMS (slave mode selection) only. Fixes: 9eba381 ("iio: make stm32 trigger driver use INDIO_HARDWARE_TRIGGERED mode") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: imu: adis16480: Fix acceleration scale factor for adis16480Dragos Bogdan2017-08-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the datasheet, the range of the acceleration is [-10 g, + 10 g], so the scale factor should be 10 instead of 5. Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: adc: stm32: fix common clock rateFabrice Gasnier2017-07-301-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADC clock input is provided to internal prescaler (that decreases its frequency). It's then used as reference clock for conversions. - Fix common clock rate used then by stm32-adc sub-devices. Take common prescaler into account. Currently, rate is used to set "boost" mode. It may unnecessarily be set. This impacts power consumption. - Fix ADC max clock rate on STM32H7 (fADC from datasheet). Currently, prescaler may be set too low. This can result in ADC reference clock used for conversion to exceed max allowed clock frequency. Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: adc: ina219: Avoid underflow for sleeping timeStefan Brüns2017-07-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Proper support for the INA219 lowered the minimum sampling period from 2*140us to 2*84us. Subtracting 200us later leads to an underflow and an almost infinite udelay later. Using a signed int for the sampling period provides sufficient range (at most 2*8640*1024us), but catches the underflow when comparing with buffer_us. Fixes: 18edac2e22f4 ("iio: adc: Fix integration time/averaging for INA219/220") Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: trigger: stm32-timer: add enable attributeFabrice Gasnier2017-07-301-14/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to use encoder mode, timers needs to be enabled (e.g. CEN bit) along with peripheral clock. Add IIO_CHAN_INFO_ENABLE attribute to handle this. Also, in triggered mode, CEN bit is set automatically in hardware. Then clock must be enabled before starting triggered mode. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: trigger: stm32-timer: fix get/set down count directionFabrice Gasnier2017-07-301-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") This fixes two issues: - stm32_set_count_direction: to set down direction - stm32_get_count_direction: to get down direction IIO core provides/expects value to be an index of iio_enum items array. This needs to be turned by these routines into TIM_CR1_DIR (e.g. BIT(4)) value. Also, report error when attempting to write direction, when in encoder mode: in this case, direction is read only (given by encoder inputs). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: trigger: stm32-timer: fix write_raw return valueFabrice Gasnier2017-07-301-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") IIO core expects zero as return value for write_raw() callback in case of success. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: trigger: stm32-timer: fix quadrature mode get routineFabrice Gasnier2017-07-301-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: 4adec7da0536 ("iio: stm32 trigger: Add quadrature encoder device") SMS bitfiled is mode + 1. After reset, upon boot, SMS = 0. When reading from sysfs, stm32_get_quadrature_mode() returns -1 (e.g. -EPERM) which is wrong error code here. So, check SMS bitfiled matches valid encoder mode, or return -EINVAL. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| | * | | iio: bmp280: properly initialize device for humidity readingAndreas Klinger2017-07-302-3/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the device is not initialized at least once it happens that the humidity reading is skipped, which means the special value 0x8000 is delivered. For omitting this case the oversampling of the humidity must be set before the oversampling of the temperature und pressure is set as written in the datasheet of the BME280. Furthermore proper error detection is added in case a skipped value is read from the device. This is done also for pressure and temperature reading. Especially it don't make sense to compensate this value and treat it as regular value. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * | | | staging: rtl8188eu: add RNX-N150NUB supportCharles Milette2017-08-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for USB Device Rosewill RNX-N150NUB. VendorID: 0x0bda, ProductID: 0xffef Signed-off-by: Charles Milette <charles.milette@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | Revert "staging: fsl-mc: be consistent when checking strcmp() return"Colin Ian King2017-08-161-3/+3
| | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The previous fix removed the equal to zero comparisons by the strcmps and now the function always returns true. Revert this change to restore the original correctly functioning code. Detected by CoverityScan, CID#1452267 ("Constant expression result") This reverts commit b93ad9a067e1515af42da7d56bc61f1a25075f94. Fixes: b93ad9a067e1 ("staging: fsl-mc: be consistent when checking strcmp() return") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | | Merge tag 'ntb-4.13-bugfixes' of git://github.com/jonmason/ntbLinus Torvalds2017-08-282-5/+3
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull NTB fixes from Jon Mason: "NTB bug fixes to address an incorrect ntb_mw_count reference in the NTB transport, improperly bringing down the link if SPADs are corrupted, and an out-of-order issue regarding link negotiation and data passing" * tag 'ntb-4.13-bugfixes' of git://github.com/jonmason/ntb: ntb: ntb_test: ensure the link is up before trying to configure the mws ntb: transport shouldn't disable link due to bogus values in SPADs ntb: use correct mw_count function in ntb_tool and ntb_transport
| * | | | ntb: transport shouldn't disable link due to bogus values in SPADsDave Jiang2017-08-011-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems that under certain scenarios the SPAD can have bogus values caused by an agent (i.e. BIOS or other software) that is not the kernel driver, and that causes memory window setup failure. This should not cause the link to be disabled because if we do that, the driver will never recover again. We have verified in testing that this issue happens and prevents proper link recovery. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Fixes: 84f766855f61 ("ntb: stop link work when we do not have memory")
| * | | | ntb: use correct mw_count function in ntb_tool and ntb_transportLogan Gunthorpe2017-07-172-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After converting to the new API, both ntb_tool and ntb_transport are using ntb_mw_count to iterate through ntb_peer_get_addr when they should be using ntb_peer_mw_count. This probably isn't an issue with the Intel and AMD drivers but this will matter for any future driver with asymetric memory window counts. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Fixes: 443b9a14ecbe ("NTB: Alter MW API to support multi-ports devices")
* | | | | Merge branch 'for-linus' of ↵Linus Torvalds2017-08-266-13/+45
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: - a tweak to the IBM Trackpoint driver that helps recognizing trackpoints on never Lenovo Carbons - a fix to the ALPS driver solving scroll issues on some Dells - yet another ACPI ID has been added to Elan I2C toucpad driver - quieted diagnostic message in soc_button_array driver * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: ALPS - fix two-finger scroll breakage in right side on ALPS touchpad Input: soc_button_array - silence -ENOENT error on Dell XPS13 9365 Input: trackpoint - add new trackpoint firmware ID Input: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310
| * | | | | Input: ALPS - fix two-finger scroll breakage in right side on ALPS touchpadMasaki Ota2017-08-252-10/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixed the issue that two finger scroll does not work correctly on V8 protocol. The cause is that V8 protocol X-coordinate decode is wrong at SS4 PLUS device. I added SS4 PLUS X decode definition. Mote notes: the problem manifests itself by the commit e7348396c6d5 ("Input: ALPS - fix V8+ protocol handling (73 03 28)"), where a fix for the V8+ protocol was applied. Although the culprit must have been present beforehand, the two-finger scroll worked casually even with the wrongly reported values by some reason. It got broken by the commit above just because it changed x_max value, and this made libinput correctly figuring the MT events. Since the X coord is reported as falsely doubled, the events on the right-half side go outside the boundary, thus they are no longer handled. This resulted as a broken two-finger scroll. One finger event is decoded differently, and it didn't suffer from this problem. The problem was only about MT events. --tiwai Fixes: e7348396c6d5 ("Input: ALPS - fix V8+ protocol handling (73 03 28)") Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Tested-by: Takashi Iwai <tiwai@suse.de> Tested-by: Paul Donohue <linux-kernel@PaulSD.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
| * | | | | Input: soc_button_array - silence -ENOENT error on Dell XPS13 9365Hans de Goede2017-08-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Dell XPS13 9365 has an INT33D2 ACPI node with no GPIOs, causing the following error in dmesg: [ 7.172275] soc_button_array: probe of INT33D2:00 failed with error -2 This commit silences this, by returning -ENODEV when there are no GPIOs. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196679 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
| * | | | | Input: trackpoint - add new trackpoint firmware IDAaron Ma2017-08-192-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Synaptics add new TP firmware ID: 0x2 and 0x3, for now both lower 2 bits are indicated as TP. Change the constant to bitwise values. This makes trackpoint to be recognized on Lenovo Carbon X1 Gen5 instead of it being identified as "PS/2 Generic Mouse". Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
| * | | | | Input: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310KT Liao2017-08-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add ELAN0602 to the list of known ACPI IDs to enable support for ELAN touchpads found in Lenovo Yoga310. Signed-off-by: KT Liao <kt.liao@emc.com.tw> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* | | | | | Merge tag 'pci-v4.13-fixes-3' of ↵Linus Torvalds2017-08-261-10/+3
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fix from Bjorn Helgaas: "Remove needlessly alarming MSI affinity warning (this is not actually a bug fix, but the warning prompts unnecessary bug reports)" * tag 'pci-v4.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI/MSI: Don't warn when irq_create_affinity_masks() returns NULL
| * | | | | | PCI/MSI: Don't warn when irq_create_affinity_masks() returns NULLChristoph Hellwig2017-08-261-10/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | irq_create_affinity_masks() can return NULL on non-SMP systems, when there are not enough "free" vectors available to spread, or if memory allocation for the CPU masks fails. Only the allocation failure is of interest, and even then the system will work just fine except for non-optimally spread vectors. Thus remove the warnings. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: David S. Miller <davem@davemloft.net>
* | | | | | | Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds2017-08-262-9/+17
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull virtio fixes from Michael Tsirkin: "Fixes two obvious bugs in virtio pci" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: virtio_pci: fix cpu affinity support virtio_blk: fix incorrect message when disk is resized
| * | | | | | | virtio_pci: fix cpu affinity supportChristoph Hellwig2017-08-251-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for virtqueues"") removed the adjustment of the pre_vectors for the virtio MSI-X vector allocation which was added in commit fb5e31d9 ("virtio: allow drivers to request IRQ affinity when creating VQs"). This will lead to an incorrect assignment of MSI-X vectors, and potential deadlocks when offlining cpus. Signed-off-by: Christoph Hellwig <hch@lst.de> Fixes: 0b0f9dc5 ("Revert "virtio_pci: use shared interrupts for virtqueues") Reported-by: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
| * | | | | | | virtio_blk: fix incorrect message when disk is resizedStefan Hajnoczi2017-08-251-6/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The message printed on disk resize is incorrect. The following is printed when resizing to 2 GiB: $ truncate -s 1G test.img $ qemu -device virtio-blk-pci,logical_block_size=4096,... (qemu) block_resize drive1 2G virtio_blk virtio0: new size: 4194304 4096-byte logical blocks (17.2 GB/16.0 GiB) The virtio_blk capacity config field is in 512-byte sector units regardless of logical_block_size as per the VIRTIO specification. Therefore the message should read: virtio_blk virtio0: new size: 524288 4096-byte logical blocks (2.15 GB/2.0 GiB) Note that this only affects the printed message. Thankfully the actual block device has the correct size because the block layer expects capacity in sectors. Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* | | | | | | | Merge tag 'for-linus-20170825' of git://git.infradead.org/linux-mtdLinus Torvalds2017-08-262-1/+13
|\ \ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull MTD fixes from Brian Norris: "Two fixes - one for a 4.13 regression, and the other for an older one: - Atmel NAND: since we started utilizing ONFI timings, we found that we were being too restrict at rejecting them, partly due to discrepancies in ONFI 4.0 and earlier versions. Relax the restriction to keep these platforms booting. This is a 4.13-rc1 regression. - nandsim: repeated probe/removal may not work after a failed init, because we didn't free up our debugfs files properly on the failure path. This has been around since 3.8, but it's nice to get this fixed now in a nice easy patch that can target -stable, since there's already refactoring work (that also fixes the issue) targeted for the next merge window" * tag 'for-linus-20170825' of git://git.infradead.org/linux-mtd: mtd: nand: atmel: Relax tADL_min constraint mtd: nandsim: remove debugfs entries in error path
| * | | | | | | | mtd: nand: atmel: Relax tADL_min constraintBoris Brezillon2017-08-251-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Version 4 of the ONFI spec mandates that tADL be at least 400 nanoseconds, but, depending on the master clock rate, 400 ns may not fit in the tADL field of the SMC reg. We need to relax the check and accept the -ERANGE return code. Note that previous versions of the ONFI spec had a lower tADL_min (100 or 200 ns). It's not clear why this timing constraint got increased but it seems most NANDs are fine with values lower than 400ns, so we should be safe. Fixes: f9ce2eddf176 ("mtd: nand: atmel: Add ->setup_data_interface() hooks") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
| * | | | | | | | mtd: nandsim: remove debugfs entries in error pathUwe Kleine-König2017-08-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The debugfs entries must be removed before an error is returned in the probe function. Otherwise another try to load the module fails and when the debugfs files are accessed without the module loaded, the kernel still tries to call a function in that module. Fixes: 5346c27c5fed ("mtd: nandsim: Introduce debugfs infrastructure") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* | | | | | | | | Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds2017-08-262-37/+6
|\ \ \ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull block fixes from Jens Axboe: "A small batch of fixes that should be included for the 4.13 release. This contains: - Revert of the 4k loop blocksize support. Even with a recent batch of 4 fixes, we're still not really happy with it. Rather than be stuck with an API issue, let's revert it and get it right for 4.14. - Trivial patch from Bart, adding a few flags to the blk-mq debugfs exports that were added in this release, but not to the debugfs parts. - Regression fix for bsg, fixing a potential kernel panic. From Benjamin. - Tweak for the blk throttling, improving how we account discards. From Shaohua" * 'for-linus' of git://git.kernel.dk/linux-block: blk-mq-debugfs: Add names for recently added flags bsg-lib: fix kernel panic resulting from missing allocation of reply-buffer Revert "loop: support 4k physical blocksize" blk-throttle: cap discard request size
| * | | | | | | | | Revert "loop: support 4k physical blocksize"Omar Sandoval2017-08-232-37/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's some stuff still up in the air, let's not get stuck with a subpar ABI. I'll follow up with something better for 4.14. Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 01:30:21 +0100