| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
| |
This patch implements real Xen acpi memory hotplug driver as module.
When loaded, it replaces Xen stub driver.
When an acpi memory device hotadd event occurs, it notifies OS and
invokes notification callback, adding related memory device and parsing
memory information, finally hypercall to xen hypervisor to add memory.
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch create a file (xen-stub.c) for Xen stub drivers.
Xen stub drivers are used to reserve space for Xen drivers, i.e.
memory hotplug and cpu hotplug, and to block native drivers loaded,
so that real Xen drivers can be modular and loaded on demand.
This patch is specific for Xen memory hotplug (other Xen logic
can add stub drivers on their own). The xen stub driver will
occupied earlier via subsys_initcall (than native memory hotplug
driver via module_init and so blocking native). Later real Xen
memory hotplug logic will unregister the stub driver and register
itself to take effect on demand.
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
into fixes
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
This is yet another critical imxfb fixes held off by absence of FB
maintainer for some time.
* tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: imxfb: Do not crash on reboot
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Issuing a "reboot" command after the LCD times out causes the following
warnings:
Requesting system reboot
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:471 clk_disable+0x24/0x50()
Modules linked in:
[<c001ad90>] (unwind_backtrace+0x0/0xf4) from [<c0025aac>] (warn_slowpath_common+0x48/0x60)
[<c0025aac>] (warn_slowpath_common+0x48/0x60) from [<c0025ae0>] (warn_slowpath_null+0x1c/0x24)
[<c0025ae0>] (warn_slowpath_null+0x1c/0x24) from [<c03960a0>] (clk_disable+0x24/0x50)
[<c03960a0>] (clk_disable+0x24/0x50) from [<c02695a0>] (imxfb_disable_controller+0x48/0x7c)
[<c02695a0>] (imxfb_disable_controller+0x48/0x7c) from [<c029d838>] (platform_drv_shutdown+0x18/0x1c)
[<c029d838>] (platform_drv_shutdown+0x18/0x1c) from [<c02990fc>] (device_shutdown+0x48/0x14c)
[<c02990fc>] (device_shutdown+0x48/0x14c) from [<c003d09c>] (kernel_restart_prepare+0x2c/0x3c)
[<c003d09c>] (kernel_restart_prepare+0x2c/0x3c) from [<c003d0e4>] (kernel_restart+0xc/0x48)
[<c003d0e4>] (kernel_restart+0xc/0x48) from [<c003d1e8>] (sys_reboot+0xc0/0x1bc)
[<c003d1e8>] (sys_reboot+0xc0/0x1bc) from [<c0014ca0>] (ret_fast_syscall+0x0/0x2c)
---[ end trace da6b502ca79c854f ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:380 clk_unprepare+0x1c/0x2c()
Modules linked in:
[<c001ad90>] (unwind_backtrace+0x0/0xf4) from [<c0025aac>] (warn_slowpath_common+0x48/0x60)
[<c0025aac>] (warn_slowpath_common+0x48/0x60) from [<c0025ae0>] (warn_slowpath_null+0x1c/0x24)
[<c0025ae0>] (warn_slowpath_null+0x1c/0x24) from [<c0396338>] (clk_unprepare+0x1c/0x2c)
[<c0396338>] (clk_unprepare+0x1c/0x2c) from [<c02695a8>] (imxfb_disable_controller+0x50/0x7c)
[<c02695a8>] (imxfb_disable_controller+0x50/0x7c) from [<c029d838>] (platform_drv_shutdown+0x18/0x1c)
[<c029d838>] (platform_drv_shutdown+0x18/0x1c) from [<c02990fc>] (device_shutdown+0x48/0x14c)
[<c02990fc>] (device_shutdown+0x48/0x14c) from [<c003d09c>] (kernel_restart_prepare+0x2c/0x3c)
[<c003d09c>] (kernel_restart_prepare+0x2c/0x3c) from [<c003d0e4>] (kernel_restart+0xc/0x48)
[<c003d0e4>] (kernel_restart+0xc/0x48) from [<c003d1e8>] (sys_reboot+0xc0/0x1bc)
[<c003d1e8>] (sys_reboot+0xc0/0x1bc) from [<c0014ca0>] (ret_fast_syscall+0x0/0x2c)
---[ end trace da6b502ca79c8550 ]---
------------[ cut here ]------------
This happens because "reboot" triggers imxfb_shutdown(), which calls
imxfb_disable_controller with the clocks already disabled.
To prevent this, add a clock enabled status so that we can check if the clocks
are enabled before disabling them.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There are a number of bugs in the error paths of this driver. Make
use of devm_ functions to simplify the cleanup on error.
Based on a patch by Russell King.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
the variable cpuclk and clk_name should be properly freed when error happens.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
| | |\ \ \ \
| | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
fixes
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
commit c045e3f13 (ARM: imx: include iram.h rather than mach/iram.h) changed the
location of iram.h, which causes the following build error when building the coda
driver:
drivers/media/platform/coda.c:27:23: error: mach/iram.h: No such file or directory
drivers/media/platform/coda.c: In function 'coda_probe':
drivers/media/platform/coda.c:2000: error: implicit declaration of function 'iram_alloc'
drivers/media/platform/coda.c:2001: warning: assignment makes pointer from integer without a cast
drivers/media/platform/coda.c: In function 'coda_remove':
drivers/media/platform/coda.c:2024: error: implicit declaration of function 'iram_free'
Since the content of iram.h is not imx specific, move it to
include/linux/platform_data/imx-iram.h instead. This is an intermediate solution
until the i.MX iram allocator is converted to the generic SRAM allocator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
That branch fixes build error for S3C24XX/S3C64xx. And corrects dw-mshc
properties on EXYNOS5 DT and fixes IRQ mapping on Cragganmore board.
* 'v3.8-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: dts: correct the dw-mshc timing properties as per binding
ARM: S3C64XX: Fix build error with CONFIG_S3C_DEV_FB disabled
+ Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |\ \ \ \ \ \
| | | |_|_|_|/
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It's the second batch of fixes for 3.8, which includes one fixing for
!CONFIG_SMP build, two patches fixing broken imxfb driver caused by
multiplatform conversion, and a couple of pm/hotplug fixes.
* tag 'imx-fixes-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: correct low-power mode setting
ARM: imx: disable cpu in .cpu_kill hook
video: imxfb: fix imxfb_info configuration order
ARM: imx: platform-imx-fb: modifies platform device name
ARM: imx: fix build error with !CONFIG_SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The devtype field for fbi (struct imxfb_info) must be set after memset call to
avoid some wrong behaviour (pixel size).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
- cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
- ACPI cpufreq fix from Thomas Schlichter.
- cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
- APEI workaround for incorrect BIOS information from Lans Zhang.
* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Add module aliases for acpi-cpufreq
ACPI: Check MSR valid bit before using P-state frequencies
PM / devfreq: exynos4_bus: honor RCU lock usage
PM / devfreq: add locking documentation for recommended_opp
cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
cpufreq: OMAP: use RCU locks around usage of OPP
ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
ACPI / processor: Get power info before updating the C-states
powernow-k8: Add a kconfig dependency on acpi-cpufreq
ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
intel_idle: Don't register CPU notifier if we are not running.
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The acpi core will call request_module("acpi-cpufreq") on subsystem init,
but this will fail if the module isn't available at that stage of boot.
Add some module aliases to ensure that udev can load the module on Intel
and AMD systems with the appropriate feature bits - I /think/ that this
will also work on VIA systems, but haven't verified that.
References: http://lkml.kernel.org/r/1448223.sdUJnNSRz4@vostro.rjw.lan
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Leonid Isaev <lisaev@umail.iu.edu>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
To fix incorrect P-state frequencies which can happen on
some AMD systems f594065faf4f9067c2283a34619fc0714e79a98d
"ACPI: Add fixups for AMD P-state figures"
introduced a quirk to obtain the correct values by reading
from AMD specific MSRs.
This did cause a regression when running a kernel using that
quirk under Xen which does (currently) not pass through MSR
reads to the HW. Instead the guest gets a 0 in return.
And this seems to cause a failure to initialize the ondemand
governour (hard to say for sure as all P-states appear to run
at the same frequency).
While this should also be fixed in the hypervisor (to allow
a guest to read that MSR), this patch is intended to work
around the issue in the meantime. In discussion it turned out
that indeed real HW/BIOSes may choose to not set the valid bit
and thus mark the P-state as invalid. So this could be considered
a fix for broken BIOSes that also works around the issue on Xen.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: 3.7+ <stable@vger.kernel.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
OPP pointers cannot be expected to be valid beyond the boundary
of rcu_read_lock and rcu_read_unlock. Unfortunately, the current
exynos4 busfreq driver does not honor the usage constraint and stores
the OPP pointer in struct busfreq_data. This could potentially
become invalid later such as: across devfreq opp change decisions,
resulting in unpredictable behavior.
To fix this, we introduce a busfreq specific busfreq_opp_info
structure which is used to handle OPP information. OPP information
is de-referenced to voltage and frequency pairs as needed into
busfreq_opp_info structure and used as needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
OPP pointers are protected by RCU locks, the pointer validity is
permissible only under the section of rcu_read_lock to rcu_read_unlock
Add documentation to the effect.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
OPP pointer is RCU protected, hence after finding it, de-reference
also should be protected with the same RCU context else the OPP
pointer may become invalid.
Reported-by: Jack Mitchell <jack@embed.me.uk>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Jack Mitchell <jack@embed.me.uk>
Acked-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
OPP pointer is RCU protected, hence after finding it, de-reference
also should be protected with the same RCU context else the OPP
pointer may become invalid.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The bit width check was introduced by 15afae60 (ACPI, APEI: Fix
incorrect APEI register bit width check and usage), and a fixup
for incorrect 32-bit width memory address was given by f712c71
(ACPI, APEI: Fixup common access width firmware bug). Now there
is a similar symptom:
[Firmware Bug]: APEI: Invalid bit width + offset in GAR [0x12345000/64/0/3/0]
Another bogus BIOS reports an incorrect 64-bit width in trigger table.
Thus, apply to a similar workaround for 64-bit width memory address.
Signed-off-by: Lans Zhang <jia.zhang@windriver.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
acpi_processor_get_power_info() has to be called before
acpi_processor_setup_cpuidle_states() to have the latest
information available. This fixes the missing C-state information
after AC-->DC transition.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Andreas reports in https://bugzilla.kernel.org/show_bug.cgi?id=51741
that with his Gentoo config, acpi-cpufreq wasn't enabled and
powernow-k8 couldn't handoff properly to acpi-cpufreq leading to
running without P-state support (i.e., cores are constantly in P0).
To alleaviate that, we need to make powernow-k8 depend on acpi-cpufreq
so that acpi-cpufreq is always present.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51741
Reported-by: Andreas <linuxuser330250@gmx.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
If cpuidle is disabled, that means that:
per_cpu(acpi_cpuidle_device, pr->id)
is set to NULL as the acpi_processor_power_init ends up failing at
retval = cpuidle_register_driver(&acpi_idle_driver)
(in acpi_processor_power_init) and never sets the per_cpu idle
device. So when acpi_processor_hotplug on CPU online notification
tries to reference said device it crashes:
cpu 3 spinlock event irq 62
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffff81381013>] acpi_processor_setup_cpuidle_cx+0x3f/0x105
PGD a259b067 PUD ab38b067 PMD 0
Oops: 0002 [#1] SMP
odules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c nouveau mxm_wmi wmi radeon ttm sg sr_mod sd_mod cdrom ata_generic ata_piix libata crc32c_intel scsi_mod atl1c i915 fbcon tileblit font bitblit softcursor drm_kms_helper video xen_blkfront xen_netfront fb_sys_fops sysimgblt sysfillrect syscopyarea xenfs xen_privcmd mperf
CPU 1
Pid: 3047, comm: bash Not tainted 3.8.0-rc3upstream-00250-g165c029 #1 MSI MS-7680/H61M-P23 (MS-7680)
RIP: e030:[<ffffffff81381013>] [<ffffffff81381013>] acpi_processor_setup_cpuidle_cx+0x3f/0x105
RSP: e02b:ffff88001742dca8 EFLAGS: 00010202
RAX: 0000000000010be9 RBX: ffff8800a0a61800 RCX: ffff880105380000
RDX: 0000000000000003 RSI: 0000000000000200 RDI: ffff8800a0a61800
RBP: ffff88001742dce8 R08: ffffffff81812360 R09: 0000000000000200
R10: aaaaaaaaaaaaaaaa R11: 0000000000000001 R12: ffff8800a0a61800
R13: 00000000ffffff01 R14: 0000000000000000 R15: ffffffff81a907a0
FS: 00007fd6942f7700(0000) GS:ffff880105280000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000004 CR3: 00000000a6773000 CR4: 0000000000042660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process bash (pid: 3047, threadinfo ffff88001742c000, task ffff880017944000)
Stack:
0000000000000150 ffff880100f59e00 ffff88001742dcd8 ffff8800a0a61800
0000000000000000 00000000ffffff01 0000000000000000 ffffffff81a907a0
ffff88001742dd18 ffffffff813815b1 ffff88001742dd08 ffffffff810ae336
Call Trace:
[<ffffffff813815b1>] acpi_processor_hotplug+0x7c/0x9f
[<ffffffff810ae336>] ? schedule_delayed_work_on+0x16/0x20
[<ffffffff8137ee8f>] acpi_cpu_soft_notify+0x90/0xca
[<ffffffff8166023d>] notifier_call_chain+0x4d/0x70
[<ffffffff810bc369>] __raw_notifier_call_chain+0x9/0x10
[<ffffffff81094a4b>] __cpu_notify+0x1b/0x30
[<ffffffff81652cf7>] _cpu_up+0x103/0x14b
[<ffffffff81652e18>] cpu_up+0xd9/0xec
[<ffffffff8164a254>] store_online+0x94/0xd0
[<ffffffff814122fb>] dev_attr_store+0x1b/0x20
[<ffffffff81216404>] sysfs_write_file+0xf4/0x170
This patch fixes it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | |_|_|_|/ /
| |/| | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The 'intel_idle_probe' probes the CPU and sets the CPU notifier.
But if later on during the module initialization we fail (say
in cpuidle_register_driver), we stop loading, but we neglect
to unregister the CPU notifier. This means that during CPU
hotplug events the system will fail:
calling intel_idle_init+0x0/0x326 @ 1
intel_idle: MWAIT substates: 0x1120
intel_idle: v0.4 model 0x2A
intel_idle: lapic_timer_reliable_states 0xffffffff
intel_idle: intel_idle yielding to none
initcall intel_idle_init+0x0/0x326 returned -19 after 14 usecs
... some time later, offlining and onlining a CPU:
cpu 3 spinlock event irq 62
BUG: unable to ] __cpuidle_register_device+0x1c/0x120
PGD 99b8b067 PUD 99b95067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: xen_evtchn nouveau mxm_wmi wmi radeon ttm i915 fbcon tileblit font atl1c bitblit softcursor drm_kms_helper video xen_blkfront xen_netfront fb_sys_fops sysimgblt sysfillrect syscopyarea xenfs xen_privcmd mperf
CPU 0
Pid: 2302, comm: udevd Not tainted 3.8.0-rc3upstream-00249-g09ad159 #1 MSI MS-7680/H61M-P23 (MS-7680)
RIP: e030:[<ffffffff814d956c>] [<ffffffff814d956c>] __cpuidle_register_device+0x1c/0x120
RSP: e02b:ffff88009dacfcb8 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff880105380000 RCX: 000000000000001c
RDX: 0000000000000000 RSI: 0000000000000055 RDI: ffff880105380000
RBP: ffff88009dacfce8 R08: ffffffff81a4f048 R09: 0000000000000008
R10: 0000000000000008 R11: 0000000000000000 R12: ffff880105380000
R13: 00000000ffffffdd R14: 0000000000000000 R15: ffffffff81a523d0
FS: 00007f37bd83b7a0(0000) GS:ffff880105200000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 00000000a09ea000 CR4: 0000000000042660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process udevd (pid: 2302, threadinfo ffff88009dace000, task ffff88009afb47f0)
Stack:
ffffffff8107f2d0 ffffffff810c2fb7 ffff88009dacfce8 00000000ffffffea
ffff880105380000 00000000ffffffdd ffff88009dacfd08 ffffffff814d9882
0000000000000003 ffff880105380000 ffff88009dacfd28 ffffffff81340afd
Call Trace:
[<ffffffff8107f2d0>] ? collect_cpu_info_local+0x30/0x30
[<ffffffff810c2fb7>] ? __might_sleep+0xe7/0x100
[<ffffffff814d9882>] cpuidle_register_device+0x32/0x70
[<ffffffff81340afd>] intel_idle_cpu_init+0xad/0x110
[<ffffffff81340bc8>] cpu_hotplug_notify+0x68/0x80
[<ffffffff8166023d>] notifier_call_chain+0x4d/0x70
[<ffffffff810bc369>] __raw_notifier_call_chain+0x9/0x10
[<ffffffff81094a4b>] __cpu_notify+0x1b/0x30
[<ffffffff81652cf7>] _cpu_up+0x103/0x14b
[<ffffffff81652e18>] cpu_up+0xd9/0xec
[<ffffffff8164a254>] store_online+0x94/0xd0
[<ffffffff814122fb>] dev_attr_store+0x1b/0x20
[<ffffffff81216404>] sysfs_write_file+0xf4/0x170
[<ffffffff811a1024>] vfs_write+0xb4/0x130
[<ffffffff811a17ea>] sys_write+0x5a/0xa0
[<ffffffff816643a9>] system_call_fastpath+0x16/0x1b
Code: 03 18 00 c9 c3 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 30 48 89 5d e8 4c 89 65 f0 48 89 fb 4c 89 6d f8 e8 84 08 00 00 <48> 8b 78 08 49 89 c4 e8 f8 7f c1 ff 89 c2 b8 ea ff ff ff 84 d2
RIP [<ffffffff814d956c>] __cpuidle_register_device+0x1c/0x120
RSP <ffff88009dacfcb8>
This patch fixes that by moving the CPU notifier registration
as the last item to be done by the module.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"One more oversight in the debugfs code was reported and fixed, plus a
documentation fix."
* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix small typo in regmap_bulk_write comment
regmap: debugfs: Fix seeking from the cache
|
| | |\ \ \ \ \ \ \ |
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
We don't want to bomb out early if we failed to get the cache any more,
just soldier on instead and we won't get confused and always return the
first block.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| | | |/ / / / / /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Signed-off-by: Nestor Ovroy <novroy@riseup.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |\ \ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The flag parameter is added in the cyclic transfer request.
Use the flag option of:
- DMA_PREP_INTERRUPT for enabling interrupt.
- DMA_CTRL_ACK for deciding whether ack is requred or not for
descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
HW chaining is currently broken in imx-dma. It can be easily reproduced doing
intensive accesses to a external MMC card and checking how the file system
is corrupted.
Preventing the driver to use HW chaining solves these issues.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
| | | |_|_|_|_|/ /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
ioat does DMA memory sync with DMA_TO_DEVICE direction on a buffer allocated
for DMA_FROM_DEVICE dma, resulting in the following warning from dma debug.
Fixed the dma_sync_single_for_device() call to use the correct direction.
[ 226.288947] WARNING: at lib/dma-debug.c:990 check_sync+0x132/0x550()
[ 226.288948] Hardware name: ProLiant DL380p Gen8
[ 226.288951] ioatdma 0000:00:04.0: DMA-API: device driver syncs DMA memory with different direction [device address=0x00000000ffff7000] [size=4096 bytes] [mapped with DMA_FROM_DEVICE] [synced with DMA_TO_DEVICE]
[ 226.288953] Modules linked in: iTCO_wdt(+) sb_edac(+) ioatdma(+) microcode serio_raw pcspkr edac_core hpwdt(+) iTCO_vendor_support hpilo(+) dca acpi_power_meter ata_generic pata_acpi sd_mod crc_t10dif ata_piix libata hpsa tg3 netxen_nic(+) sunrpc dm_mirror dm_region_hash dm_log dm_mod
[ 226.288967] Pid: 1055, comm: work_for_cpu Tainted: G W 3.3.0-0.20.el7.x86_64 #1
[ 226.288968] Call Trace:
[ 226.288974] [<ffffffff810644cf>] warn_slowpath_common+0x7f/0xc0
[ 226.288977] [<ffffffff810645c6>] warn_slowpath_fmt+0x46/0x50
[ 226.288980] [<ffffffff81345502>] check_sync+0x132/0x550
[ 226.288983] [<ffffffff81345c9f>] debug_dma_sync_single_for_device+0x3f/0x50
[ 226.288988] [<ffffffff81661002>] ? wait_for_common+0x72/0x180
[ 226.288995] [<ffffffffa019590f>] ioat_xor_val_self_test+0x3e5/0x832 [ioatdma]
[ 226.288999] [<ffffffff811a5739>] ? kfree+0x259/0x270
[ 226.289004] [<ffffffffa0195d77>] ioat3_dma_self_test+0x1b/0x20 [ioatdma]
[ 226.289008] [<ffffffffa01952c3>] ioat_probe+0x2f8/0x348 [ioatdma]
[ 226.289011] [<ffffffffa0195f51>] ioat3_dma_probe+0x1d5/0x2aa [ioatdma]
[ 226.289016] [<ffffffffa0194d12>] ioat_pci_probe+0x139/0x17c [ioatdma]
[ 226.289020] [<ffffffff81354b8c>] local_pci_probe+0x5c/0xd0
[ 226.289023] [<ffffffff81083e50>] ? destroy_work_on_stack+0x20/0x20
[ 226.289025] [<ffffffff81083e68>] do_work_for_cpu+0x18/0x30
[ 226.289029] [<ffffffff8108d997>] kthread+0xb7/0xc0
[ 226.289033] [<ffffffff8166cef4>] kernel_thread_helper+0x4/0x10
[ 226.289036] [<ffffffff81662d20>] ? _raw_spin_unlock_irq+0x30/0x50
[ 226.289038] [<ffffffff81663234>] ? retint_restore_args+0x13/0x13
[ 226.289041] [<ffffffff8108d8e0>] ? kthread_worker_fn+0x1a0/0x1a0
[ 226.289044] [<ffffffff8166cef0>] ? gs_change+0x13/0x13
[ 226.289045] ---[ end trace e1618afc7a606089 ]---
[ 226.289047] Mapped at:
[ 226.289048] [<ffffffff81345307>] debug_dma_map_page+0x87/0x150
[ 226.289050] [<ffffffffa019653c>] dma_map_page.constprop.18+0x70/0xb34 [ioatdma]
[ 226.289054] [<ffffffffa0195702>] ioat_xor_val_self_test+0x1d8/0x832 [ioatdma]
[ 226.289058] [<ffffffffa0195d77>] ioat3_dma_self_test+0x1b/0x20 [ioatdma]
[ 226.289061] [<ffffffffa01952c3>] ioat_probe+0x2f8/0x348 [ioatdma]
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
| |\ \ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.pengutronix.de/git/wsa/linux
Pill i2c fixes from Wolfram Sang:
"Here are a few, typical driver fixes for the I2C subsystem"
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c-designware: add missing MODULE_LICENSE
i2c: omap: fix draining irq handling
i2c: omap: errata i462: fix incorrect ack for arbitration lost interrupt
i2c: muxes: fix wrong use of sizeof(ptr)
i2c: sirf: register i2c_client from dt child-nodes in probe entry
i2c: mxs: Fix type of error code
i2c: mxs: Fix misuse init_completion
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The driver can also be built as a module so add MODULE_LICENSE for it. In
addition add MODULE_DESCRIPTION as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Commit 0bdfe0cb803dce699ff337c35d8e97ac355fa417 (i2c: omap: sanitize
exit path) changed the interrupt handler to exit early and complete
the transfer after the draining IRQ is handled. As a result, the ARDY
may not be cleared properly, and it may cause all future I2C transfers
to timeout with "timeout waiting for bus ready". This is reproducible
at least with N900 when twl4030_gpio makes a long write (> FIFO size)
during the probe (http://marc.info/?l=linux-omap&m=135818882610432&w=2).
The fix is to continue until we get ARDY interrupt that completes the
transfer. Tested with 3.8-rc4 + N900: 20 boots in a row without errors;
without the patch the problem triggers after few reboots.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The errata handling function acks wrong interrupt in case of "Arbitration
lost". Fix it.
Discovered during code review, the real impact of the bug is unknown.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
sizeof when applied to a pointer typed expression gives the size of
the pointer
The semantic patch that makes this output is available
in scripts/coccinelle/misc/noderef.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
in probe() entry of i2c_driver, set the of node of adapter and
call of_i2c_register_devices to register all i2c_client from
dt child-nodes
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
cmd_err is used to handle error code, so it should not be unsigned.
This fixes the following warning when building with W=1 option:
drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:331:19: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
|
| | | |/ / / / / /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The init_completion() call does reinit not only the variable carrying
the flag that the completion finished, but also initialized the
waitqueue associated with the completion. On the contrary, the
INIT_COMPLETION() call only reinits the flag.
In case there was anything still stuck in the waitqueue, subsequent call
to init_completion() would be able to create possible race condition. This
patch uses the proper function and moves init_completion() into .probe() call
of the driver, to be issued only once.
Note that such scenario is impossible, since two threads can never enter the
mxs_i2c_xfer_msg(), since whole this section is protected by mutex in I2C core.
This by no means allows this issue to exit though.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
| |\ \ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB fixes from Greg Kroah-Hartman:
"Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver
build issues (it's just some code moving around and being deleted)."
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: fix build error in ehci-mxc
USB: EHCI: add a name for the platform-private field
USB: EHCI: fix incorrect configuration test
USB: EHCI: Move definition of EHCI_STATS to ehci.h
USB: UHCI: fix IRQ race during initialization
usb: gadget: FunctionFS: Fix missing braces in parse_opts
usb: dwc3: gadget: fix ep->maxburst for ep0
ARM: i.MX clock: Change the connection-id for fsl-usb2-udc
usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremap
usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_id
usb: musb: cppi_dma: drop '__init' annotation
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver. As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch (as1642) adds an ehci->priv field for private use by EHCI
platform drivers. The space was provided some time ago, but it didn't
have a name.
Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch (as1641) fixes a minor bug in ehci-hcd left over from when
the Chipidea driver was converted to the "ehci-hcd is a library"
scheme. The test for whether the Chipidea platform driver is active
should be IS_ENABLED(), not defined().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Without this, platform drivers e.g. ehci-omap.c will see a
different version of struct ehci_hcd than ehci-hcd.c and
break reference to 'debug_dir' and 'priv' members when
CONFIG_USB_DEBUG is enabled.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
