| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Niklas Cassel <nks@flawful.org> says:
This series adds support for Command Duration Limits.
The series is based on linux tag: v6.4-rc1
The series can also be found in git: https://github.com/floatious/linux/commits/cdl-v7
=================
CDL in ATA / SCSI
=================
Command Duration Limits is defined in:
T13 ATA Command Set - 5 (ACS-5) and
T10 SCSI Primary Commands - 6 (SPC-6) respectively
(a simpler version of CDL is defined in T10 SPC-5).
CDL defines Duration Limits Descriptors (DLD).
7 DLDs for read commands and 7 DLDs for write commands.
Simply put, a DLD contains a limit and a policy.
A command can specify that a certain limit should be applied by setting
the DLD index field (3 bits, so 0-7) in the command itself.
The DLD index points to one of the 7 DLDs.
DLD index 0 means no descriptor, so no limit.
DLD index 1-7 means DLD 1-7.
A DLD can have a few different policies, but the two major ones are:
-Policy 0xF (abort), command will be completed with command aborted error
(ATA) or status CHECK CONDITION (SCSI), with sense data indicating that
the command timed out.
-Policy 0xD (complete-unavailable), command will be completed without
error (ATA) or status GOOD (SCSI), with sense data indicating that the
command timed out. Note that the command will not have transferred any
data to/from the device when the command timed out, even though the
command returned success.
Regardless of the CDL policy, in case of a CDL timeout, the I/O will
result in a -ETIME error to user-space.
The DLDs are defined in the CDL log page(s) and are readable and writable.
Reading and writing the CDL DLDs are outside the scope of the kernel.
If a user wants to read or write the descriptors, they can do so using a
user-space application that sends passthrough commands, such as cdl-tools:
https://github.com/westerndigitalcorporation/cdl-tools
================================
The introduction of ioprio hints
================================
What the kernel does provide, is a method to let I/O use one of the CDL DLDs
defined in the device. Note that the kernel will simply forward the DLD index
to the device, so the kernel currently does not know, nor does it need to know,
how the DLDs are defined inside the device.
The way that the CDL DLD index is supplied to the kernel is by introducing a
new 10 bit "ioprio hint" field within the existing 16 bit ioprio definition.
Currently, only 6 out of the 16 ioprio bits are in use, the remaining 10 bits
are unused, and are currently explicitly disallowed to be set by the kernel.
For now, we only add ioprio hints representing CDL DLD index 1-7. Additional
ioprio hints for other QoS features could be defined in the future.
A theoretical future work could be to make an I/O scheduler aware of these
hints. E.g. for CDL, an I/O scheduler could make use of the duration limit
in each descriptor, and take that information into account while scheduling
commands. Right now, the ioprio hints will be ignored by the I/O schedulers.
==============================
How to use CDL from user-space
==============================
Since CDL is mutually exclusive with NCQ priority
(see ncq_prio_enable and sas_ncq_prio_enable in
Documentation/ABI/testing/sysfs-block-device),
CDL has to be explicitly enabled using:
echo 1 > /sys/block/$bdev/device/cdl_enable
Since the ioprio hints are supplied through the existing I/O priority API,
it should be simple for an application to make use of the ioprio hints.
It simply has to reuse one of the new macros defined in
include/uapi/linux/ioprio.h: IOPRIO_PRIO_HINT() or IOPRIO_PRIO_VALUE_HINT(),
and supply one of the new hints defined in include/uapi/linux/ioprio.h:
IOPRIO_HINT_DEV_DURATION_LIMIT_[1-7], which indicates that the I/O should
use the corresponding CDL DLD index 1-7.
By reusing the I/O priority API, the user can both define a DLD to use per
AIO (io_uring sqe->ioprio or libaio iocb->aio_reqprio) or per-thread
(ioprio_set()).
=======
Testing
=======
With the following fio patches:
https://github.com/floatious/fio/commits/cdl
fio adds support for ioprio hints, such that CDL can be tested using e.g.:
fio --ioengine=io_uring --cmdprio_percentage=10 --cmdprio_hint=DLD_index
A simple way to test is to use a DLD with a very short duration limit,
and send large reads. Regardless of the CDL policy, in case of a CDL
timeout, the I/O will result in a -ETIME error to user-space.
We also provide a CDL test suite located in the cdl-tools repo, see:
https://github.com/westerndigitalcorporation/cdl-tools#testing-a-system-command-duration-limits-support
We have tested this patch series using:
-real hardware
-the following QEMU implementation:
https://github.com/floatious/qemu/tree/cdl
(NOTE: the QEMU implementation requires you to define the CDL policy at compile
time, so you currently need to recompile QEMU when switching between policies.)
===================
Further information
===================
For further information about CDL, see Damien's slides:
Presented at SDC 2021:
https://www.snia.org/sites/default/files/SDC/2021/pdfs/SNIA-SDC21-LeMoal-Be-On-Time-command-duration-limits-Feature-Support-in%20Linux.pdf
Presented at Lund Linux Con 2022:
https://drive.google.com/file/d/1I6ChFc0h4JY9qZdO1bY5oCAdYCSZVqWw/view?usp=sharing
================
Changes since V6
================
-Rebased series on v6.4-rc1.
-Picked up Reviewed-by tags from Hannes (Thank you Hannes!)
-Picked up Reviewed-by tag from Christoph (Thank you Christoph!)
-Changed KernelVersion from 6.4 to 6.5 for new sysfs attributes.
For older change logs, see previous patch series versions:
https://lore.kernel.org/linux-scsi/20230406113252.41211-1-nks@flawful.org/
https://lore.kernel.org/linux-scsi/20230404182428.715140-1-nks@flawful.org/
https://lore.kernel.org/linux-scsi/20230309215516.3800571-1-niklas.cassel@wdc.com/
https://lore.kernel.org/linux-scsi/20230124190308.127318-1-niklas.cassel@wdc.com/
https://lore.kernel.org/linux-scsi/20230112140412.667308-1-niklas.cassel@wdc.com/
https://lore.kernel.org/linux-scsi/20221208105947.2399894-1-niklas.cassel@wdc.com/
Link: https://lore.kernel.org/r/20230511011356.227789-1-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
A CDL timeout for policy 0xF is defined as a NCQ error, just with a CDL
specific sk/asc/ascq in the sense data. Therefore, the existing code in
libata does not need to be modified to handle a policy 0xF CDL timeout.
For Command Duration Limits policy 0xD:
The device shall complete the command without error with the additional
sense code set to DATA CURRENTLY UNAVAILABLE.
Since a CDL timeout for policy 0xD is not an error, we cannot use the NCQ
Command Error log (10h).
Instead, we need to read the Sense Data for Successful NCQ Commands log
(0Fh).
In the success case, just like in the error case, we cannot simply read a
log page from the interrupt handler itself, since reading a log page
involves sending a READ LOG DMA EXT or READ LOG EXT command.
Therefore, we add a new EH action ATA_EH_GET_SUCCESS_SENSE. When a command
completes without error, and when the ATA_SENSE bit is set, this new action
is set as pending, and EH is scheduled.
This way, similar to the NCQ error case, the log page will be read from EH
context.
An alternative would have been to add a new kthread or workqueue to handle
this. However, extending EH can be done with minimal changes and avoids the
need to synchronize a new kthread/workqueue with EH.
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-20-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For devices supporting the command duration limits feature, translate the
dld field of read and write operation to set the command duration limit
index field of the command task file when the duration limit feature is
enabled.
The function ata_set_tf_cdl() is introduced to do this. For unqueued (non
NCQ) read and write operations, this function sets the command duration
limit index set as the lower 3 bits of the feature field. For queued NCQ
read/write commands, the index is set as the lower 3 bits of the auxiliary
field.
The flag ATA_QCFLAG_HAS_CDL is introduced to indicate that a command
taskfile has a non zero cdl field.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-19-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for the ATA feature control sub-page of the control mode page
to enable/disable the command duration limits feature using the cdl_ctrl
field of the ATA feature control sub-page.
Both mode sense and mode select translation are supported. For mode sense,
the ata device flag ATA_DFLAG_CDL_ENABLED is used to cache the status of
the command duration limits feature. Enabling this feature is done using a
SET FEATURES command with a cdl action set to 1 when the page cdl_ctrl
field value is 0x2 (T2A and T2B pages supported). If this field is 0, CDL
is disabled using the SET FEATURES command with a cdl action set to 0.
Since a device CDL and NCQ priority features should not be used
simultaneously, ata_mselect_control_ata_feature() returns an error when
attempting to enable CDL with the device priority feature enabled.
Conversely, the function ata_ncq_prio_enable_store() used to enable the use
of the device NCQ priority feature through sysfs is modified to return an
error if the device CDL feature is enabled.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-18-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Modify ata_scsiop_mode_sense() and ata_msense_control() to support mode
sense access to the T2A and T2B sub-pages of the control mode page.
ata_msense_control() is modified to support sub-pages. The T2A sub-page is
generated using the read descriptors of the command duration limits log
page 18h. The T2B sub-page is generated using the write descriptors of the
same log page. With the addition of these sub-pages, getting all sub-pages
of the control mode page is also supported by increasing the value of
ATA_SCSI_RBUF_SIZE from 576B up to 2048B to ensure that all sub-pages fit
in the fill buffer.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-17-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For a scsi MAINTENANCE_IN/MI_REPORT_SUPPORTED_OPERATION_CODES operation,
add the translation of the rwcdlp and cdlp bits for the READ 16 and WRITE
16 commands. If the ATA device does not support command duration limits,
these bits are always 0. If the ATA device supports command duration
limits, the rwcdlp bit is set to 1 for READ 16 and WRITE 16 and the cdlp
bits are set to 0x1 for READ 16 and 0x2 for WRITE 16. These correspond to
the T2A mode page containing the read descriptors and to the T2B mode page
containing the write descriptors, as defined in SAT-5.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-16-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Use the supported capabilities identify device data log page to detect if a
device supports the command duration limits feature. For devices supporting
this feature, set the device flag ATA_DFLAG_CDL. To support SCSI-ATA
translation, retrieve the command duration limits log page 18h and cache
this page content using the cdl array added to the ata_device data
structure.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-15-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, ata_eh_request_sense() unconditionally sets the scsicmd->result
to SAM_STAT_CHECK_CONDITION.
For Command Duration Limits policy 0xD:
The device shall complete the command without error (SAM_STAT_GOOD) with
the additional sense code set to DATA CURRENTLY UNAVAILABLE.
It is perfectly fine to have sense data for a command that returned
completion without error.
In order to support for CDL policy 0xD, we have to remove this assumption
that having sense data means that the command failed
(SAM_STAT_CHECK_CONDITION).
Change ata_eh_request_sense() to not set SAM_STAT_CHECK_CONDITION, and
instead move the setting of SAM_STAT_CHECK_CONDITION to the single caller
that wants SAM_STAT_CHECK_CONDITION set, that way ata_eh_request_sense()
can be reused in a follow-up patch that adds support for CDL policy 0xD.
The only caller of ata_eh_request_sense() is protected by: if (!(qc->flags
& ATA_QCFLAG_SENSE_VALID)), so we can remove this duplicated check from
ata_eh_request_sense() itself.
Additionally, ata_eh_request_sense() is only called from
ata_eh_analyze_tf(), which is only called when iteratating the QCs using
ata_qc_for_each_raw(), which does not include the internal tag, so cmd can
never be NULL (all non-internal commands have qc->scsicmd set), so remove
the !cmd check as well.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-14-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There is no need to check if !cmd as this can only happen for ATA internal
commands which uses the ATA internal tag (32).
Most users of ata_scsi_set_sense() are from _xlat functions that translate
a scsicmd to an ATA command. These obviously have a qc->scsicmd.
ata_scsi_qc_complete() can also call ata_scsi_set_sense() via
ata_gen_passthru_sense() / ata_gen_ata_sense(), called via
ata_scsi_qc_complete(). This callback is only called for translated
commands, so it also has a qc->scsicmd.
ata_eh_analyze_ncq_error(): the NCQ error log can only contain a 0-31
value, so it will never be able to get the ATA internal tag (32).
ata_eh_request_sense(): only called by ata_eh_analyze_tf(), which is only
called when iteratating the QCs using ata_qc_for_each_raw(), which does not
include the internal tag.
Since there is no existing call site where cmd can be NULL, remove the !cmd
check from ata_scsi_set_sense() and ata_scsi_set_sense_information().
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-13-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commands using a duration limit descriptor that has limit policies set to a
value other than 0x0 may be failed by the device if one of the limits are
exceeded. For such commands, since the failure is the result of the user
duration limit configuration and workload, the commands should not be
retried and terminated immediately. Furthermore, to allow the user to
differentiate these "soft" failures from hard errors due to hardware
problem, a different error code than EIO should be returned.
There are 2 cases to consider:
(1) The failure is due to a limit policy failing the command with a check
condition sense key, that is, any limit policy other than 0xD. For this
case, scsi_check_sense() is modified to detect failures with the ABORTED
COMMAND sense key and the COMMAND TIMEOUT BEFORE PROCESSING or COMMAND
TIMEOUT DURING PROCESSING or COMMAND TIMEOUT DURING PROCESSING DUE TO ERROR
RECOVERY additional sense code. For these failures, a SUCCESS disposition
is returned so that scsi_finish_command() is called to terminate the
command.
(2) The failure is due to a limit policy set to 0xD, which result in the
command being terminated with a GOOD status, COMPLETED sense key, and DATA
CURRENTLY UNAVAILABLE additional sense code. To handle this case, the
scsi_check_sense() is modified to return a SUCCESS disposition so that
scsi_finish_command() is called to terminate the command. In addition,
scsi_decide_disposition() has to be modified to see if a command being
terminated with GOOD status has sense data. This is as defined in SCSI
Primary Commands - 6 (SPC-6), so all according to spec, even if GOOD status
commands were not checked before.
If scsi_check_sense() detects sense data representing a duration limit,
scsi_check_sense() will set the newly introduced SCSI ML byte
SCSIML_STAT_DL_TIMEOUT. This SCSI ML byte is checked in scsi_noretry_cmd(),
so that a command that failed because of a CDL timeout cannot be
retried. The SCSI ML byte is also checked in scsi_result_to_blk_status() to
complete the command request with the BLK_STS_DURATION_LIMIT status, which
result in the user seeing ETIME errors for the failed commands.
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-12-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Introduce the command duration limits helper function sd_cdl_dld() to set
the DLD bits of READ/WRITE 16 and READ/WRITE 32 commands to indicate to the
device the command duration limit descriptor to apply to the commands.
When command duration limits are enabled, sd_cdl_dld() obtains the index of
the descriptor to apply to the command using the hints field of the request
IO priority value (hints IOPRIO_HINT_DEV_DURATION_LIMIT_1 to
IOPRIO_HINT_DEV_DURATION_LIMIT_7).
If command duration limits is disabled (which is the default), the limit
index "0" is always used to indicate "no limit" for a command.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-11-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add the sysfs scsi_device attribute cdl_enable to allow a user to enable or
disable a device command duration limits feature. CDL is disabled by
default. This feature must be explicitly enabled by a user by setting the
cdl_enable attribute to 1.
The new function scsi_cdl_enable() does not do anything beside setting the
cdl_enable field of struct scsi_device in the case of a (real) SCSI device
(e.g. a SAS HDD). For ATA devices, the command duration limits feature
needs to be enabled/disabled using the ATA feature sub-page of the control
mode page. To do so, the scsi_cdl_enable() function checks if this mode
page is supported using scsi_mode_sense(). If it is, scsi_mode_select() is
used to enable and disable CDL.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-10-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Introduce the function scsi_cdl_check() to detect if a device supports
command duration limits (CDL). Support for the READ 16, WRITE 16, READ 32
and WRITE 32 commands are checked using the function scsi_report_opcode()
to probe the rwcdlp and cdlp bits as they indicate the mode page defining
the command duration limits descriptors that apply to the command being
tested.
If any of these commands support CDL, the field cdl_supported of struct
scsi_device is set to 1 to indicate that the device supports CDL.
Support for CDL for a device is advertizes through sysfs using the new
cdl_supported device attribute. This attribute value is 1 for a device
supporting CDL and 0 otherwise.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Co-developed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-9-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The REPORT_SUPPORTED_OPERATION_CODES command allows checking for support of
commands that have the same opcode but different service actions, such as
READ 32 and WRITE 32. However, the current implementation of
scsi_report_opcode() only allows checking an operation code without a
service action differentiation.
Add the "sa" argument to scsi_report_opcode() to allow passing a service
action. If a non-zero service action is specified, the reporting options
field value is set to 3 to have the service action field taken into account
by the device. If no service action field is specified (zero), the
reporting options field is set to 1 as before.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-8-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allow scsi_mode_sense() to retrieve sub-pages of mode pages by adding the
subpage argument. Change all the current caller sites to specify the
subpage 0.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-7-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
SCSI has two different getters:
- get_XXX_byte() (in scsi_cmnd.h) which takes a struct scsi_cmnd *, and
- XXX_byte() (in scsi.h) which takes a scmd->result.
The proper name for get_scsi_ml_byte() should thus be without the get_
prefix, as it takes a scmd->result. Rename the function to rectify this.
(This change was suggested by Mike Christie.)
Additionally, move get_scsi_ml_byte() to scsi_priv.h since both scsi_lib.c
and scsi_error.c will need to use this helper in a follow-up patch.
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-6-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In SCSI, we get the sense data as part of the completion, for ATA however,
we need to fetch the sense data as an extra step. For an aborted ATA
command the sense data is fetched via libata's ->eh_strategy_handler().
For Command Duration Limits policy 0xD:
The device shall complete the command without error with the additional
sense code set to DATA CURRENTLY UNAVAILABLE.
In order to handle this policy in libata, we intend to send a successful
command via SCSI EH, and let libata's ->eh_strategy_handler() fetch the
sense data for the good command. This is similar to how we handle an
aborted ATA command, just that we need to read the Successful NCQ Commands
log instead of the NCQ Command Error log.
When we get a SATA completion with successful commands, ATA_SENSE will be
set, indicating that some commands in the completion have sense data.
The sense_valid bitmask in the Sense Data for Successful NCQ Commands log
will inform exactly which commands that had sense data, which might be a
subset of all the commands that was completed in the same completion. (Yet
all will have ATA_SENSE set, since the status is per completion.)
The successful commands that have e.g. a "DATA CURRENTLY UNAVAILABLE" sense
data will have a SCSI ML byte set, so scsi_eh_flush_done_q() will not set
the scmd->result to DID_TIME_OUT for these commands. However, the
successful commands that did not have sense data, must not get their result
marked as DID_TIME_OUT by SCSI EH.
Add a new flag SCMD_FORCE_EH_SUCCESS, which tells SCSI EH to not mark a
command as DID_TIME_OUT, even if it has scmd->result == SAM_STAT_GOOD.
This will be used by libata in a subsequent commit.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-5-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Mike Christie <michael.christie@oracle.com> says:
The patches in this thread allow us to use the block pr_ops with LIO's
target_core_iblock module to support cluster applications in VMs. They
were built over Linus's tree. They also apply over linux-next and
Martin's tree and Jens's trees.
Currently, to use windows clustering or linux clustering (pacemaker +
cluster labs scsi fence agents) in VMs with LIO and vhost-scsi, you
have to use tcmu or pscsi or use a cluster aware FS/framework for the
LIO pr file. Setting up a cluster FS/framework is pain and waste when
your real backend device is already a distributed device, and pscsi
and tcmu are nice for specific use cases, but iblock gives you the
best performance and allows you to use stacked devices like
dm-multipath. So these patches allow iblock to work like pscsi/tcmu
where they can pass a PR command to the backend module. And then
iblock will use the pr_ops to pass the PR command to the real devices
similar to what we do for unmap today.
The patches are separated in the following groups:
Patch 1 - 2:
- Add block layer callouts for reading reservations and rename reservation
error code.
Patch 3 - 5:
- SCSI support for new callouts.
Patch 6:
- DM support for new callouts.
Patch 7 - 13:
- NVMe support for new callouts.
Patch 14 - 18:
- LIO support for new callouts.
This patchset has been tested with the libiscsi PGR ops and with
window's failover cluster verification test. Note that for scsi
backend devices we need this patchset:
https://lore.kernel.org/linux-scsi/20230123221046.125483-1-michael.christie@oracle.com/T/#m4834a643ffb5bac2529d65d40906d3cfbdd9b1b7
to handle UAs. To reduce the size of this patchset that's being done
separately to make reviewing easier. And to make merging easier this
patchset and the one above do not have any conflicts so can be merged
in different trees.
Link: https://lore.kernel.org/r/20230407200551.12660-1-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This adds support for the block PR callouts to target_core_iblock. This
patch doesn't attempt to implement the entire spec because there's no way
support it all like SPEC_I_PT and ALL_TG_PT. This only supports
exporting the iblock device from one path on the local target.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-19-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The backend modules don't know about ports and I_T nexuses and the pr_ops
callouts the modules will use don't support the old RESERVE/RELEASE
commands. This patch has us report we don't support those types of
commands and fail them.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-18-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The iblock pr_ops support does not support commands that require port or
I_T Nexus info. This adds a struct target_opcode_descriptor as an argument
to the enabled callout so we can still have the common tcm_is_pr_enabled
and tcm_is_scsi2_reservations_enabled functions and also determine if the
command is supported based on the command and service action and device
settings.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-17-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For the cases where you want to export a device to a VM via a single
I_T nexus and want to passthrough the PR handling to the physical/real
device you have to use pscsi or tcmu. Both are good for specific uses
however for the case where you want good performance, and are not using
SCSI devices directly (using DM/MD RAID or multipath devices) then we are
out of luck.
The following patches allow iblock to mimimally hook into the LIO PR code
and then pass the PR handling to the physical device. Note that like with
the tcmu an pscsi cases it's only supported when you export the device via
one I_T nexus.
This patch adds the initial LIO callouts. The next patch will modify
iblock.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-16-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The next patches allow us to call the block layer's pr_ops from the
backends. This will require allowing the backends to hook into the cmd
processing for SPC commands, so this renames sbc_ops to a more generic
exec_cmd_ops.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-15-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds support for the pr_ops read_reservation callout by
calling the NVMe Reservation Report helper. It then parses that info to
detect if there is a reservation and if there is then convert the
returned info to a pr_ops pr_held_reservation struct.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-14-michael.christie@oracle.com
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The next patch adds support to report the reservation type, so we need to
be able to convert from the NVMe PR value we get from the device to the
linux block layer PR value that will be returned to callers. To prepare
for that, this patch adds a nvme_pr_type enum and renames the nvme_pr_type
function.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-13-michael.christie@oracle.com
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds support for the pr_ops read_keys callout by calling the
NVMe Reservation Report helper, then parsing that info to get the
controller's registered keys. Because the callout is only used in the
kernel where the callers, like LIO, do not know about controller/host IDs,
the callout just returns the registered keys which is required by the SCSI
PR in READ KEYS command.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-12-michael.christie@oracle.com
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move the code that checks for multipath support and sends the pr command
to a new helper so it can be used by the reservation report support added
in the next patches.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-11-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch moves the pr code to it's own file because I'm going to be
adding more functions and core.c is getting bigger.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-10-michael.christie@oracle.com
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Reservation Report support needs to pass in a variable sized buffer, so
this patch has the pr command helpers take a data length argument.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-9-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This adds support in dm for the block PR read keys and read reservation
callouts.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-7-michael.christie@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This adds support in sd.c for the block PR read keys and read reservation
callouts, so upper layers like LIO can get the PR info that's been setup
using the existing pr callouts and return it to initiators.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-6-michael.christie@oracle.com
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
LIO is going to want to do the same block to/from SCSI pr types as sd.c
so this moves the sd_pr_type helper to scsi_common and renames it. The
next patch will then also add a helper to go from the SCSI value to the
block one for use with PERSISTENT_RESERVE_IN commands.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-5-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Rename sd_pr_command to sd_pr_out_command to match a
sd_pr_in_command helper added in the next patches.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-4-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
BLK_STS_NEXUS is used for NVMe/SCSI reservation conflicts and DASD's
locking feature which works similar to NVMe/SCSI reservations where a
host can get a lock on a device and when the lock is taken it will get
failures.
This patch renames BLK_STS_NEXUS so it better reflects this type of
use.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230407200551.12660-3-michael.christie@oracle.com
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516025404.2843867-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516025355.2835898-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516025322.2804923-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516013345.723623-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Xiang Chen <chenxiang66@hisilicon.com> says:
This series contains some fixes including:
- Configure initial value of some registers according to HBA model
- Change DMA setup lock timeout from 100ms to 2.5s
- Fix warnings detected by sparse
Link: https://lore.kernel.org/r/1684118481-95908-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes the following warning:
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:2168:43: sparse: sparse: restricted __le32 degrades to integer
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304161254.NztCVZIO-lkp@intel.com/
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-4-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
DMA setup lock timeout protection is added when DMA setup frames are
received. It's a function outside the protocol and used to prevent SATA
disk I/Os from being delivered for a long time. The default value is 100ms,
it's too strict and easily triggered timeout when the disk is overloaded or
faulty. Based on the average I/O latency of 300 disks, we adjust the value
to 2.5s.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For SAS HBAs of 920 and previous version, we use init_reg_v3_hw() to set
some registers which are related to HW boards. For SAS HBAs of 920B and
later version, those HW registers are set through firmware. And different
HBA models are distinguished through pci_dev->revision.
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1684118481-95908-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In the ongoing effort to replace all fake flexible arrays with true
flexible arrays, replace the sge32, sge64, and sge_skinny members of union
megasas_sgl with true flexible arrays. No binary differences are seen after
this change; sizes were already being manually calculated using the member
struct sizes directly.
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230511220957.never.919-kees@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Statically allocated array of pointers to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230511175204.281038-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Don Brace <don.brace@microchip.com> says:
These patches are based on Martin Petersen's 6.4/scsi-queue tree
https://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi.git
6.4/scsi-queue
This set of changes consists of:
* Map entire BAR 0. The driver was mapping up to and including the
controller registers, but not all of BAR 0.
* Add PCI IDs to support new controllers.
* Clean up some code by removing unnecessary NULL checks. This cleanup is
a result of a Coverity report.
* Correct a rare memory leak whenever pqi_sas_port_add_rhpy() returns an
error. This was Suggested by: Yang Yingliang <yangyingliang@huawei.com>
* Remove atomic operations on variable raid_bypass_cnt. Accuracy is not
required for driver operation. Change type from atomic_t to unsigned
int.
* Correct a rare drive hot-plug removal issue where we get a NULL
io_request. We added a check for this condition.
* Turn on NCQ priority for AIO requests to disks comprising RAID devices.
* Correct byte aligned writew() operations on some ARM servers. Changed
the writew() to two writeb() operations.
* Change how the driver checks for a sanitize operation in progress. We
were using TEST UNIT READY. We removed the TEST UNIT READY code and are
now using the controller's firmware information in order to avoid issues
caused by drives failing to complete TEST UNIT READY.
* Some customers have been requesting that we add the NUMA node to
/sys/block/sd<scsi device>/device like the nvme driver does.
* Update the copyright information to match the current year.
* Bump the driver version to 2.1.22-040.
Link: https://lore.kernel.org/r/20230428153712.297638-1-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230428153712.297638-13-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Update copyright to current year.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230428153712.297638-12-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Although NUMA node is a PCIe device level attribute, it was requested the
NUMA node be added for each exposed device similar to NVMe disks.
Example for NVMe:
/sys/block/nvme1c1n1/device/numa_node
Example for smartpqi:
/sys/block/sdh/device/numa_node
cat /sys/block/sdh/device/numa_node
0
Reviewed-by: David Strahan <david.strahan@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230428153712.297638-11-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Stop sending driver-initiated TURs to physical devices during driver
load/rescan.
Note: This does not affect SML initiated TURs.
Some Linux kernels can cause lengthy delays in OS boot if the kernel
detects that a drive is being sanitized/erased. We were using TURs to
detect if a sanitize/erase was in progress.
Some devices do not return the TUR in a timely manner, causing driver
load/rescan stalls.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230428153712.297638-10-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Correct OOPs on ARM servers during driver init.
The driver attempts to update FW with max_feature_supported value using a
writew() kernel call using a byte aligned address. This fails on some ARM
systems.
Change the writew() to two writeb() calls to update this value.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230428153712.297638-9-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
