| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This fixes a small issue in clps711x_get_duty() en passant: the
multiplication v * 0xf might have overflown.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362eab6 ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The array atmel_tcb_divisors is not supposed to be used outside of the
driver, so make it static.
This fixes a sparse warning:
drivers/pwm/pwm-atmel-tcb.c:64:10: warning: symbol 'atmel_tcb_divisors' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
pwmchip_add() unconditionally assigns the base ID dynamically. Commit
f9a8ee8c8bcd1 ("pwm: Always allocate PWM chip base ID dynamically")
dropped all base assignment from drivers under drivers/pwm/. It missed
this driver. Fix that.
Fixes: f9a8ee8c8bcd1 ("pwm: Always allocate PWM chip base ID dynamically")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
| |
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c0934e ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
| |
Add Sunplus SoC SP7021 PWM Driver
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly
found on Xilinx FPGAs. At the moment clock control is very basic: we
just enable the clock during probe and pin the frequency. In the future,
someone could add support for disabling the clock when not in use.
Some common code has been specially demarcated. While currently only
used by the PWM driver, it is anticipated that it may be split off in
the future to be used by the timer driver as well.
This driver was written with reference to Xilinx DS764 for v1.03.a [1].
[1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
| |
Per-channel data is tracked using struct pwm_device::chip_data and
struct atmel_tcb_pwm_chip::pwms[]. Simplify by using the latter
consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a problem that was supposed to be addressed by commit
6eefb79d6f5bc ("pwm: sun4i: Remove erroneous else branch") - backlight
could not be switched off on some Allwinner A20. The commit was
correct, but was not a reliable fix for the problem, which was timing
related.
The real problem for the backlight switching problem was that sleeping
for a full period did not work, because delay_us is always zero.
It is zero because the period (plus 1 microsecond) is rounded down to
the next "jiffies", but the period is less than one jiffy.
On my Cubieboard 2, the period is 5ms, and 1 jiffy (at the default
HZ=100) is 10ms, so nsecs_to_jiffies(10ms+1us)=0.
The roundtrip from nanoseconds to jiffies and back to microseconds is
an unnecessary loss of precision; always rounding down (via
nsecs_to_jiffies()) then causes the breakage.
This patch eliminates this roundtrip, and directly converts from
nanoseconds to microseconds (for usleep_range()), using
DIV_ROUND_UP_ULL() to force rounding up. This way, the sleep time is
never zero, and after the sleep, we are guaranteed to be in a
different period, and the device is ready for another control command
for sure.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
|
| |
Basically this code did "jiffies + period - jiffies", and we can
simply eliminate the "jiffies" time stamp here.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |
|
|
|
|
|
|
| |
Its value is calculated in sun4i_pwm_apply() and is used only there.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixlet from Juergen Gross:
"A single cleanup patch for the Xen balloon driver"
* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: don't use PV mode extra memory for zone device allocations
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When running as a Xen PV guest use the extra memory (memory which isn't
allocated for the guest at boot time) only for ballooning purposes and
not for zone device allocations. This will remove some code without any
lack of functionality.
While at it move some code to get rid of another #ifdef.
Remove a comment which is stale since some time now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220407093857.1485-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
- Fix a regression with battery data failing to load from DT
* tag 'for-v5.18-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: Reset err after not finding static battery
power: supply: samsung-sdi-battery: Add missing charge restart voltages
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Otherwise power_supply_get_battery_info always returns -ENODEV
on devices that do not have a static battery, even when a simple
battery is found.
Fixes: c8aee3f41cb8 ("power: supply: Static data for Samsung batteries")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Two of the batteries were missing charging restart voltages,
meaning they can drain if the algorithm relies on restarting
charging at this voltage. Fix it up.
Fixes: c8aee3f41cb8 ("power: supply: Static data for Samsung batteries")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Regular set of fixes for drivers and the dev-interface"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: Fix undefined behavior due to shift overflowing the constant
i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
i2c: dev: check return value when calling dev_set_name()
i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
i2c: pasemi: Wait for write xfers to finish
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Sparse has warned us about wrong address space for user pointers:
i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
i2c-dev.c:561:50: expected unsigned char [usertype] *buf
i2c-dev.c:561:50: got void [noderef] __user *
Force cast the pointer to (__u8 *) that is used by I²C core code.
Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.
Fixes: 3265a7e6b41b ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638aba ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A single fix for gpio-sim and two patches for GPIO ACPI pulled from
Andy:
- fix the set/get_multiple() callbacks in gpio-sim
- use correct format characters in gpiolib-acpi
- use an unsigned type for pins in gpiolib-acpi"
* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sim: fix setting and getting multiple lines
gpiolib: acpi: Convert type for pin to be unsigned
gpiolib: acpi: use correct format characters
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v5.18-2
* Couple of fixes related to handling unsigned value of the pin from ACPI
gpiolib:
- acpi: Convert type for pin to be unsigned
- acpi: use correct format characters
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
A pin that comes from ACPI tables is of unsigned type. This also applies
to the internal APIs which use unsigned int to store the pin. Convert
type for pin to be unsigned in the places where it's not yet true.
While at it, add a stub for acpi_get_and_request_gpiod() for the sake
of consistency in the APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When compiling with -Wformat, clang emits the following warning:
gpiolib-acpi.c:393:4: warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat]
pin);
^~~
So warning that '%hhX' is paired with an 'int' is all just completely
mindless and wrong. Sadly, I can see a different bogus warning reason
why people would want to use '%02hhX'.
Again, the *sane* thing from a human perspective is to use '%02X. But
if the compiler doesn't do any range analysis at all, it could decide
that "Oh, that print format could need up to 8 bytes of space in the
result". Using '%02hhX' would cut that down to two.
And since we use
char ev_name[5];
and currently use "_%c%02hhX" as the format string, even a compiler
that doesn't notice that "pin <= 255" test that guards this all will
go "OK, that's at most 4 bytes and the final NUL termination, so it's
fine".
While a compiler - like gcc - that only sees that the original source
of the 'pin' value is a 'unsigned short' array, and then doesn't take
the "pin <= 255" into account, will warn like this:
gpiolib-acpi.c: In function 'acpi_gpiochip_request_interrupt':
gpiolib-acpi.c:206:24: warning: '%02X' directive writing between 2 and 4 bytes into a region of size 3 [-Wformat-overflow=]
sprintf(ev_name, "_%c%02X",
^~~~
gpiolib-acpi.c:206:20: note: directive argument in the range [0, 65535]
because gcc isn't being very good at that argument range analysis either.
In other words, the original use of 'hhx' was bogus to begin with, and
due to *another* compiler warning being bad, and we had that bad code
being written back in 2016 to work around _that_ compiler warning
(commit e40a3ae1f794: "gpio: acpi: work around false-positive
-Wstring-overflow warning").
Sadly, two different bad compiler warnings together does not make for
one good one.
It just makes for even more pain.
End result: I think the simplest and cleanest option is simply the
proposed change which undoes that '%hhX' change for gcc, and replaces
it with just using a slightly bigger stack allocation. It's not like
a 5-byte allocation is in any way likely to have saved any actual stack,
since all the other variables in that function are 'int' or bigger.
False-positive compiler warnings really do make people write worse
code, and that's a problem. But on a scale of bad code, I feel that
extending the buffer trivially is better than adding a pointless cast
that literally makes no sense.
At least in this case the end result isn't unreadable or buggy. We've
had several cases of bad compiler warnings that caused changes that
were actually horrendously wrong.
Fixes: e40a3ae1f794 ("gpio: acpi: work around false-positive -Wstring-overflow warning")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We need to take mask into account in the set/get_multiple() callbacks.
Use bitmap_replace() instead of bitmap_copy().
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of SoC bugfixes that came in since the merge
window, and more of them are already pending.
This batch includes:
- A boot time regression fix for davinci that triggered on
multi_v5_defconfig when booting any platform
- Defconfig updates to address removed features, changed symbol names
or dependencies, for gemini, ux500, and pxa
- Email address changes for Krzysztof Kozlowski
- Build warning fixes for ep93xx and iop32x
- Devicetree warning fixes across many platforms
- Minor bugfixes for the reset controller, memory controller and SCMI
firmware subsystems plus the versatile-express board"
* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
ARM: config: Update Gemini defconfig
arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
ARM: dts: align SPI NOR node name with dtschema
ARM: dts: Fix more boolean properties with values
arm/arm64: dts: qcom: Fix boolean properties with values
arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
arm: dts: imx: Fix boolean properties with values
arm64: dts: tegra: Fix boolean properties with values
arm: dts: at91: Fix boolean properties with values
arm: configs: imote2: Drop defconfig as board support dropped.
ep93xx: clock: Don't use plain integer as NULL pointer
ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
ARM: vexpress/spc: Fix all the kernel-doc build warnings
ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
ARM: config: u8500: Re-enable AB8500 battery charging
ARM: config: u8500: Add some common hardware
memory: fsl_ifc: populate child nodes of buses and mfd devices
ARM: config: Refresh U8500 defconfig
firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
firmware: arm_scmi: Replace zero-length array with flexible-array member
...
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
arm/fixes
Reset controller fixes for v5.18
Document the deprecated 'hisi,rst-syscon' device tree property for
hisilicon,hi3660-reset, add an error check to reset deassertion in
reset-rzg2l-usbphy-ctrl, restore transfer error handling in Tegra
reset-bpmp, and document the optional 'resets' device tree property
for socionext,uniphier-reset.
* tag 'reset-fixes-for-v5.18' of git://git.pengutronix.de/pza/linux:
dt-bindings: reset: Add parent "resets" property as optional
reset: tegra-bpmp: Restore Handle errors in BPMP response
reset: renesas: Check return value of reset_control_deassert()
dt-bindings: reset: document deprecated HiSilicon property
Link: https://lore.kernel.org/r/20220406153337.1265414-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This reverts following commit 69125b4b9440 ("reset: tegra-bpmp: Revert
Handle errors in BPMP response").
The Tegra194 HDA reset failure is fixed by commit d278dc9151a0 ("ALSA:
hda/tegra: Fix Tegra194 HDA reset failure"). The temporary revert of
original commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") can be removed now.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/1641995806-15245-1-git-send-email-spujar@nvidia.com
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Deasserting the reset is vital, therefore bail out in case of error.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/b2131908-0110-006b-862f-080517f3e2d8@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes
Memory controller drivers - fixes for v5.18
Issues in v5.18:
1. Freescale/NXP: fix populating children of Integrated Flash Controller
DT nodes.
Issues existing before:
1. Renesas: fix platform-device leak in probe's error path.
2. Atmel: fix of_node reference leak in probe's error path.
3. Synopsys: correct the bindings for snps,ddrc-3.80a (interrupts are
required).
* tag 'memory-controller-drv-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: fsl_ifc: populate child nodes of buses and mfd devices
dt-bindings: memory: snps,ddrc-3.80a compatible also need interrupts
memory: atmel-ebi: Fix missing of_node_put in atmel_ebi_probe
memory: renesas-rpc-if: fix platform-device leak in error path
Link: https://lore.kernel.org/r/20220407081448.113208-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit 3e25f800afb8 ("memory: fsl_ifc: populate child devices without
relying on simple-bus") was trying to replace the "simple-bus"
compatible with explicit bus populate in the driver. But
of_platform_populate() only populates child nodes of ifc without
populating child buses and child mfd devices residing under ifc. Change
it to of_platform_default_populate() to fix the problem.
Fixes: 3e25f800afb8 ("memory: fsl_ifc: populate child devices without relying on simple-bus")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20220307204118.19093-1-leoyang.li@nxp.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 87108dc78eb8 ("memory: atmel-ebi: Enable the SMC clock if specified")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220309110144.22412-1-linmq006@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Make sure to free the flash platform device in the event that
registration fails during probe.
Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Cc: stable@vger.kernel.org # 5.8
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220303180632.3194-1-johan@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The sparse checker complains about converting pointers between address
spaces. We correctly stored an __iomem pointer in struct scmi_optee_channel,
but discarded the __iomem when returning it from get_channel_shm, causing one
warning. Then we passed the non-__iomem pointer return from get_channel_shm
at two other places, where an __iomem pointer is expected, causing couple of
other warnings
Add the appropriate __iomem annotations at all places where it is missing.
optee.c:414:20: warning: incorrect type in return expression (different address spaces)
optee.c:414:20: expected struct scmi_shared_mem *
optee.c:414:20: got struct scmi_shared_mem [noderef] __iomem *shmem
optee.c:426:26: warning: incorrect type in argument 1 (different address spaces)
optee.c:426:26: expected struct scmi_shared_mem [noderef] __iomem *shmem
optee.c:426:26: got struct scmi_shared_mem *shmem
optee.c:441:30: warning: incorrect type in argument 1 (different address spaces)
optee.c:441:30: expected struct scmi_shared_mem [noderef] __iomem *shmem
optee.c:441:30: got struct scmi_shared_mem *shmem
Link: https://lore.kernel.org/r/20220404102419.1159705-1-sudeep.holla@arm.com
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://lore.kernel.org/r/20220401075537.2407376-1-lv.ruyi@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
During SCMI Clock protocol initialization, after having retrieved from the
SCMI platform all the available discrete rates for a specific clock, the
clock rates array is sorted, unfortunately using a pointer to its end as
a base instead of its start, so that sorting does not work.
Fix invocation of sort() passing as base a pointer to the start of the
retrieved clock rates array.
Link: https://lore.kernel.org/r/20220318092813.49283-1-cristian.marussi@arm.com
Fixes: dccec73de91d ("firmware: arm_scmi: Keep the discrete clock rates sorted")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On SCMI transports whose channels are based on a shared resource the TX
channel area has to be acquired by the agent before placing the desired
command into the channel and it will be then relinquished by the platform
once the related reply has been made available into the channel.
On an RX channel the logic is reversed with the platform acquiring the
channel area and the agent reliquishing it once done by calling the
scmi_clear_channel() helper.
As a consequence, even in case of error, the agent must never try to clear
a TX channel from its side: restrict the existing clear channel call on the
the reply path only to delayed responses since they are indeed coming from
the RX channel.
Link: https://lore.kernel.org/r/20220224152404.12877-1-cristian.marussi@arm.com
Fixes: e9b21c96181c ("firmware: arm_scmi: Make .clear_channel optional")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Per your suggestion, random reads now won't fail if there's a page
fault after some non-zero amount of data has been read, which makes
the behavior consistent with all other reads in the kernel.
- Rather than an inconsistent mix of random_get_entropy() returning an
unsigned long or a cycles_t, now it just returns an unsigned long.
- A memcpy() was replaced with an memmove(), because the addresses are
sometimes overlapping. In practice the destination is always before
the source, so not really an issue, but better to be correct than
not.
* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: use memmove instead of memcpy for remaining 32 bytes
random: make random_get_entropy() return an unsigned long
random: allow partial reads if later user copies fail
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Some implementations were returning type `unsigned long`, while others
that fell back to get_cycles() were implicitly returning a `cycles_t` or
an untyped constant int literal. That makes for weird and confusing
code, and basically all code in the kernel already handled it like it
was an `unsigned long`. I recently tried to handle it as the largest
type it could be, a `cycles_t`, but doing so doesn't really help with
much.
Instead let's just make random_get_entropy() return an unsigned long all
the time. This also matches the commonly used `arch_get_random_long()`
function, so now RDRAND and RDTSC return the same sized integer, which
means one can fallback to the other more gracefully.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Theodore Ts'o <tytso@mit.edu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Rather than failing entirely if a copy_to_user() fails at some point,
instead we should return a partial read for the amount that succeeded
prior, unless none succeeded at all, in which case we return -EFAULT as
before.
This makes it consistent with other reader interfaces. For example, the
following snippet for /dev/zero outputs "4" followed by "1":
int fd;
void *x = mmap(NULL, 4096, PROT_WRITE, MAP_ANONYMOUS | MAP_PRIVATE, -1, 0);
assert(x != MAP_FAILED);
fd = open("/dev/zero", O_RDONLY);
assert(fd >= 0);
printf("%zd\n", read(fd, x, 4));
printf("%zd\n", read(fd, x + 4095, 4));
close(fd);
This brings that same standard behavior to the various RNG reader
interfaces.
While we're at it, we can streamline the loop logic a little bit.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"13 fixes, all in drivers.
The most extensive changes are in the iscsi series (affecting drivers
qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
simple revert and then minor updates to pm80xx"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
scsi: qedi: Fix failed disconnect handling
scsi: iscsi: Fix NOP handling during conn recovery
scsi: iscsi: Merge suspend fields
scsi: iscsi: Fix unbound endpoint error handling
scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
scsi: iscsi: Fix endpoint reuse regression
scsi: iscsi: Release endpoint ID when its freed
scsi: iscsi: Fix offload conn cleanup when iscsid restarts
scsi: iscsi: Move iscsi_ep_disconnect()
scsi: pm80xx: Enable upper inbound, outbound queues
scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
Revert "scsi: scsi_debug: Address races following module load"
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We set the qedi_ep state to EP_STATE_OFLDCONN_START when the ep is
created. Then in qedi_set_path we kick off the offload work. If userspace
times out the connection and calls ep_disconnect, qedi will only flush the
offload work if the qedi_ep state has transitioned away from
EP_STATE_OFLDCONN_START. If we can't connect we will not have transitioned
state and will leave the offload work running, and we will free the qedi_ep
from under it.
This patch just has us init the work when we create the ep, then always
flush it.
Link: https://lore.kernel.org/r/20220408001314.5014-10-michael.christie@oracle.com
Tested-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If a offload driver doesn't use the xmit workqueue, then when we are doing
ep_disconnect libiscsi can still inject PDUs to the driver. This adds a
check for if the connection is bound before trying to inject PDUs.
Link: https://lore.kernel.org/r/20220408001314.5014-9-michael.christie@oracle.com
Tested-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Move the tx and rx suspend fields into one flags field.
Link: https://lore.kernel.org/r/20220408001314.5014-8-michael.christie@oracle.com
Tested-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If a driver raises a connection error before the connection is bound, we
can leave a cleanup_work queued that can later run and disconnect/stop a
connection that is logged in. The problem is that drivers can call
iscsi_conn_error_event for endpoints that are connected but not yet bound
when something like the network port they are using is brought down.
iscsi_cleanup_conn_work_fn will check for this and exit early, but if the
cleanup_work is stuck behind other works, it might not get run until after
userspace has done ep_disconnect. Because the endpoint is not yet bound
there was no way for ep_disconnect to flush the work.
The bug of leaving stop_conns queued was added in:
Commit 23d6fefbb3f6 ("scsi: iscsi: Fix in-kernel conn failure handling")
and:
Commit 0ab710458da1 ("scsi: iscsi: Perform connection failure entirely in
kernel space")
was supposed to fix it, but left this case.
This patch moves the conn state check to before we even queue the work so
we can avoid queueing.
Link: https://lore.kernel.org/r/20220408001314.5014-7-michael.christie@oracle.com
Fixes: 0ab710458da1 ("scsi: iscsi: Perform connection failure entirely in kernel space")
Tested-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Lee Duncan <lduncan@@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
