summaryrefslogtreecommitdiffstats
path: root/drivers (follow)
Commit message (Collapse)AuthorAgeFilesLines
* xhci: dbc: add dbgtty request to end of list once it completesMathias Nyman2024-09-051-1/+1
| | | | | | | | | | Make sure we move the requests from the read_queue to the end of the read_pool list, avoiding looping and using the same one request all the time. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240905143300.1959279-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xhci: dbc: Fix STALL transfer event handlingMathias Nyman2024-09-052-52/+83
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Don't flush all pending DbC data requests when an endpoint halts. An endpoint may halt and xHC DbC triggers a STALL error event if there's an issue with a bulk data transfer. The transfer should restart once xHC DbC receives a ClearFeature(ENDPOINT_HALT) request from the host. Once xHC DbC restarts it will start from the TRB pointed to by dequeue field in the endpoint context, which might be the same TRB we got the STALL event for. Turn the TRB to a no-op in this case to make sure xHC DbC doesn't reuse and tries to retransmit this same TRB after we already handled it, and gave its corresponding data request back. Other STALL events might be completely bogus. Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted endpoints even without any active bulk transfers. Assume STALL event is spurious if it reports 0 bytes transferred, and the endpoint stopped on the STALLED TRB. Don't give back the data request corresponding to the TRB in this case. The halted status is per endpoint. Track it with a per endpoint flag instead of the driver invented DbC wide DS_STALLED state. DbC remains in DbC-Configured state even if endpoints halt. There is no Stalled state in the DbC Port state Machine (xhci section 7.6.6) Reported-by: Łukasz Bartosik <ukaszb@chromium.org> Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/ Tested-by: Łukasz Bartosik <ukaszb@chromium.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: gadget: dummy_hcd: execute hrtimer callback in softirq contextAndrey Konovalov2024-09-041-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit a7f3813e589f ("usb: gadget: dummy_hcd: Switch to hrtimer transfer scheduler") switched dummy_hcd to use hrtimer and made the timer's callback be executed in the hardirq context. With that change, __usb_hcd_giveback_urb now gets executed in the hardirq context, which causes problems for KCOV and KMSAN. One problem is that KCOV now is unable to collect coverage from the USB code that gets executed from the dummy_hcd's timer callback, as KCOV cannot collect coverage in the hardirq context. Another problem is that the dummy_hcd hrtimer might get triggered in the middle of a softirq with KCOV remote coverage collection enabled, and that causes a WARNING in KCOV, as reported by syzbot. (I sent a separate patch to shut down this WARNING, but that doesn't fix the other two issues.) Finally, KMSAN appears to ignore tracking memory copying operations that happen in the hardirq context, which causes false positive kernel-infoleaks, as reported by syzbot. Change the hrtimer in dummy_hcd to execute the callback in the softirq context. Reported-by: syzbot+2388cdaeb6b10f0c13ac@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=2388cdaeb6b10f0c13ac Reported-by: syzbot+17ca2339e34a1d863aad@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=17ca2339e34a1d863aad Reported-by: syzbot+c793a7eca38803212c61@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=c793a7eca38803212c61 Reported-by: syzbot+1e6e0b916b211bee1bd6@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=1e6e0b916b211bee1bd6 Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202406141323.413a90d2-lkp@intel.com Fixes: a7f3813e589f ("usb: gadget: dummy_hcd: Switch to hrtimer transfer scheduler") Cc: stable@vger.kernel.org Acked-by: Marcello Sylvester Bauer <sylv@sylv.io> Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com> Reported-by: syzbot+edd9fe0d3a65b14588d5@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=edd9fe0d3a65b14588d5 Link: https://lore.kernel.org/r/20240904013051.4409-1-andrey.konovalov@linux.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: cdns2: Convert comma to semicolonChen Ni2024-09-031-2/+2
| | | | | | | | Replace a comma between expression statements by a semicolon. Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Link: https://lore.kernel.org/r/20240903073538.780996-1-nichen@iscas.ac.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: gadget: function: move u_f.h to include/linux/usb/func_utils.hMichael Grzeschik2024-09-039-94/+8
| | | | | | | | | | We move the func_utils.h header to include/linux/usb to be able to compile function drivers outside of the drivers/usb/gadget/function directory. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Link: https://lore.kernel.org/r/20240116-ml-topic-u9p-v12-1-9a27de5160e0@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* thunderbolt: Don't create device link from USB4 Host Interface to USB3 xHC hostMathias Nyman2024-09-031-30/+10
| | | | | | | | | | | | | | | | | | | USB core will create device links between tunneled USB3 devices and USB4 Host Interface during USB device creation. Those device links are removed with the tunneled USB3 devices, allowing USB4 Host Interface to runtime suspend if USB3 tunnels are not used. So remove device link creation between USB4 Host Interface and USB3 xHC during NHI probe Reported-by: Rajaram Regupathy <rajaram.regupathy@intel.com> Reported-by: Saranya Gopal <saranya.gopal@intel.com> Tested-by: Saranya Gopal <saranya.gopal@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240830152630.3943215-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: acpi: add device link between tunneled USB3 device and USB4 Host InterfaceMathias Nyman2024-09-031-0/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | Describe the power management relationship between a tunneled USB3 device and the tunnel providing USB4 host with a device link as the relationship between them is not evident from normal device hierarchy. Tunneling capable ports have an ACPI _DSD object pointing to the USB4 Host Interface that is used to establish USB3 3.x tunnels Set the link directly between tunneled USB3 devices and USB4 Host Interface to ensure that the USB4 host can runtime suspend if no tunneled USB 3.x devices exist. Current Thunderbolt code sets a link between USB4 Host Interface and USB3 xHCI host which prevents USB4 Host Interface from runtime suspending even if the USB3 host is only serving native USB devices. See commit b2be2b05cf3b ("thunderbolt: Create device links from ACPI description") for details. As the device link is only set for USB3 devices that are already tunneled we know that USB4 Host Interface exists and is bound to its driver. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240830152630.3943215-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: Add tunnel_mode parameter to usb device structureMathias Nyman2024-09-033-8/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add 'tunnel_mode' enum to usb device structure to describe if a USB3 link is tunneled over USB4, or connected directly using native USB2/USB3 protocols. Tunneled devices depend on USB4 NHI host to maintain the tunnel. Knowledge about tunneled devices is important to ensure correct suspend and resume order between USB4 hosts and tunneled devices. i.e. make sure tunnel is up before the USB device using it resumes. USB hosts such as xHCI may have vendor specific ways to detect tunneled connections. This 'tunnel_mode' parameter can be set by USB3 host driver during hcd->driver->update_device(hcd, udev) callback. tunnel_mode can be set to: USB_LINK_UNKNOWN = 0 USB_LINK_NATIVE USB_LINK_TUNNELED USB_LINK_UNKNOWN is used in case host is not capable of detecting tunneled links. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240830152630.3943215-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* xhci: Add USB4 tunnel detection for USB3 devices on Intel hostsMathias Nyman2024-09-034-0/+48
| | | | | | | | | | | | | | | | | | | | | Knowledge about tunneled devices is useful in order to correctly describe the relationship between tunneled USB3 device and USB4 Host Interface, ensuring proper suspend and resume order, and to be able to power down Thunderbolt if there is no need for tunneling. Intel hosts share if a USB3 connection is native or tunneled via vendor specific "SPR eSS PORT" registers. These vendor registers are available if host supports a vendor specific SPR shadow extended capability with ID 206. Registers are per USB3 port and 0x20 apart. Knowing the tunneling status of the device connected to roothub is enough as all its children will have the same status. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240830152630.3943215-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: f_mass_storage: Make use of the helper macro kthread_run()Hongbo Li2024-09-031-2/+1
| | | | | | | | | | Replace kthread_create/wake_up_process() with kthread_run() to simplify the code. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Hongbo Li <lihongbo22@huawei.com> Link: https://lore.kernel.org/r/20240903014249.3098082-1-lihongbo22@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: gadget: f_acm: make bInterfaceProtocol configurableMichael Walle2024-09-032-2/+54
| | | | | | | | | | | | | | | | | The bInterfaceProtocol is hardcoded to USB_CDC_ACM_PROTO_AT_V25TER. This will lead to problems with ModemManger which will gladly try to probe that port as a modem if the gadget also has a network function. ModemManager will try to send AT commands to the ACM port. Make the bInterfaceProtocol configurable. For this, track the number of instances and only allow write to the property if there are no intances (yet). This will also set bFunctionProtocol to the same value, see commit 5c8db070b448 ("USB: Change acm_iad_descriptor bFunctionProtocol to USB_CDC_ACM_PROTO_AT_V25TER") for more details. Signed-off-by: Michael Walle <mwalle@kernel.org> Link: https://lore.kernel.org/r/20240825180446.3757073-1-mwalle@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: ohci-nxp: Use helper function devm_clk_get_enabled()Zhang Zekun2024-09-031-14/+4
| | | | | | | | | | | devm_clk_get() and clk_prepare_enable() can be replaced by helper function devm_clk_get_enabled(). Let's use devm_clk_get_enabled() to simplify code and avoid calling clk_disable_unprepare(). Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20240902123020.29267-3-zhangzekun11@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: gadget: udc-xilinx: Remove trailing space after \n newlineColin Ian King2024-09-031-1/+1
| | | | | | | | | There is a extraneous space after a newline in a dev_dbg message. Remove it. Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20240901162357.144222-1-colin.i.king@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: npcm: Fix coding style with missing spaceAndreas Kühn2024-09-031-1/+1
| | | | | | | | Fixed coding style issue: added missing space. Signed-off-by: Andreas Kühn <andreas.kuehn@diekuehnen.com> Link: https://lore.kernel.org/r/20240831193407.11302-1-andreas.kuehn@diekuehnen.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc2: Adjust the timing of USB Driver Interrupt Registration in the ↵Shawn Shao2024-09-031-12/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Crashkernel Scenario The issue is that before entering the crash kernel, the DWC USB controller did not perform operations such as resetting the interrupt mask bits. After entering the crash kernel,before the USB interrupt handler registration was completed while loading the DWC USB driver,an GINTSTS_SOF interrupt was received.This triggered the misroute_irq process within the GIC handling framework,ultimately leading to the misrouting of the interrupt,causing it to be handled by the wrong interrupt handler and resulting in the issue. Summary:In a scenario where the kernel triggers a panic and enters the crash kernel,it is necessary to ensure that the interrupt mask bit is not enabled before the interrupt registration is complete. If an interrupt reaches the CPU at this moment,it will certainly not be handled correctly,especially in cases where this interrupt is reported frequently. Please refer to the Crashkernel dmesg information as follows (the message on line 3 was added before devm_request_irq is called by the dwc2_driver_probe function): [ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator [ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator [ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009] [ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18 [ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024 [ 5.908836][ C0] Call trace: [ 5.911965][ C0] dump_backtrace+0x0/0x1f0 [ 5.916308][ C0] show_stack+0x20/0x30 [ 5.920304][ C0] dump_stack+0xd8/0x140 [ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8 [ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0 [ 5.935506][ C0] handle_irq_event+0x80/0x1d0 [ 5.940109][ C0] try_one_irq+0x138/0x174 [ 5.944365][ C0] misrouted_irq+0x134/0x140 [ 5.948795][ C0] note_interrupt+0x1d0/0x30c [ 5.953311][ C0] handle_irq_event+0x13c/0x1d0 [ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260 [ 5.962779][ C0] __handle_domain_irq+0x88/0xf0 [ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0 [ 5.971985][ C0] el1_irq+0xb8/0x140 [ 5.975807][ C0] __setup_irq+0x3dc/0x7cc [ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4 [ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100 [ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0 [ 5.995178][ C0] platform_drv_probe+0x5c/0xb0 [ 5.999868][ C0] really_probe+0xf8/0x51c [ 6.004125][ C0] driver_probe_device+0xfc/0x170 [ 6.008989][ C0] device_driver_attach+0xc8/0xd0 [ 6.013853][ C0] __driver_attach+0xe8/0x1b0 [ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc [ 6.022886][ C0] driver_attach+0x2c/0x3c [ 6.027143][ C0] bus_add_driver+0xdc/0x240 [ 6.031573][ C0] driver_register+0x80/0x13c [ 6.036090][ C0] __platform_driver_register+0x50/0x5c [ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30 [ 6.046774][ C0] do_one_initcall+0x50/0x25c [ 6.051291][ C0] do_initcall_level+0xe4/0xfc [ 6.055894][ C0] do_initcalls+0x80/0xa4 [ 6.060064][ C0] kernel_init_freeable+0x198/0x240 [ 6.065102][ C0] kernel_init+0x1c/0x12c Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com> Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: xilinx: simplify with dev_err_probeKrzysztof Kozlowski2024-09-031-5/+2
| | | | | | | | | Use dev_err_probe() to make the error paths a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-11-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: rtk: return directly and simplify with devm_platform_ioremap_resourceKrzysztof Kozlowski2024-09-031-25/+8
| | | | | | | | | | | Use devm_platform_ioremap_resource() wrapper instead of two calls, which together with returning directly instead of useless goto, allows to nicely simplify the probe() function. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-10-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: rtk: use scoped device node handling to simplify error pathsKrzysztof Kozlowski2024-09-031-12/+7
| | | | | | | | | | Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-9-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: qcom: simplify with devm_platform_ioremap_resourceKrzysztof Kozlowski2024-09-031-4/+1
| | | | | | | | | | Use devm_platform_ioremap_resource() wrapper instead of two calls. This allows also dropping local 'res' variable. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-8-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: qcom: use scoped device node handling to simplify error pathsKrzysztof Kozlowski2024-09-031-6/+5
| | | | | | | | | | Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-7-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: imx8mp: use scoped device node handling to simplify error pathsKrzysztof Kozlowski2024-09-031-12/+8
| | | | | | | | | | | | | | Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Scoped/cleanup.h coding style expects variable declaration with initialization, so the of_get_compatible_child() call has to be moved earlier, before any goto jumps happen. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-6-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: imx8mp: simplify with dev_err_probeKrzysztof Kozlowski2024-09-031-10/+6
| | | | | | | | | | Use dev_err_probe() to make the error paths a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-5-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: imx8mp: simplify with devm_clk_get_enabledKrzysztof Kozlowski2024-09-031-27/+5
| | | | | | | | | | | Use devm_clk_get_enabled() to drop clock preparing and handling from error and remove paths. This makes the code a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-4-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: st: simplify pdev->dev usageKrzysztof Kozlowski2024-09-031-2/+2
| | | | | | | | | | | The probe() function already stores '&pdev->dev' in local 'dev' variable. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-3-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: st: simplify with dev_err_probeKrzysztof Kozlowski2024-09-031-6/+5
| | | | | | | | | | Use dev_err_probe() to make the error paths a bit simpler. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-2-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: dwc3: st: use scoped device node handling to simplify error pathsKrzysztof Kozlowski2024-09-031-14/+11
| | | | | | | | | | | | | | Obtain the device node reference with scoped/cleanup.h to reduce error handling and make the code a bit simpler. Scoped/cleanup.h coding style expects variable declaration with initialization, so the of_get_compatible_child() call has to be moved earlier, before any goto jumps happen. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-1-95481b9682bc@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb-storage: Constify struct usb_device_id and us_unusual_devChristophe JAILLET2024-09-0313-25/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | 'struct usb_device_id' and 'struct us_unusual_dev' are not modified in these drivers. Constifying these structures moves some data to a read-only section, so increase overall security, especially when the structure holds some function pointers (which is the case for struct us_unusual_dev). On a x86_64, with allmodconfig, as an example: Before: ====== text data bss dec hex filename 25249 4261 896 30406 76c6 drivers/usb/storage/alauda.o 3969 672 360 5001 1389 drivers/usb/storage/cypress_atacb.o After: ===== text data bss dec hex filename 25461 4041 896 30398 76be drivers/usb/storage/alauda.o 4225 400 360 4985 1379 drivers/usb/storage/cypress_atacb.o Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/b1b75a2a64b1f6cfad2a611f71393f281178fd3f.1724507157.git.christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* usb: chipidea: udc: enable suspend interrupt after usb resetXu Yang2024-09-031-1/+7
| | | | | | | | | | | | Currently, suspend interrupt is enabled before pullup enable operation. This will cause a suspend interrupt assert right after pullup DP. This suspend interrupt is meaningless, so this will ignore such interrupt by enable it after usb reset completed. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240823073832.1702135-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge 6.11-rc6 into usb-nextGreg Kroah-Hartman2024-09-03242-955/+2759
|\ | | | | | | | | | | We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * Merge tag 'pwrseq-fixes-for-v6.11-rc6' of ↵Linus Torvalds2024-08-311-0/+7
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull power sequencing fix from Bartosz Golaszewski: "A follow-up fix for the power sequencing subsystem. It turned out the previous fix for this driver was incomplete and broke the WLAN support on some platforms. This addresses the issue. - set the direction of the wlan-enable GPIO to output after requesting it as-is" * tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
| | * power: sequencing: qcom-wcn: set the wlan-enable GPIO to outputBartosz Golaszewski2024-08-311-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the wifi module isn't in output mode by default. We need to set direction to output while retaining the value that was already set to keep the ath module on if it's already started. Fixes: a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is") Link: https://lore.kernel.org/r/20240823115500.37280-1-brgl@bgdev.pl Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
| * | Merge tag 'usb-6.11-rc6' of ↵Linus Torvalds2024-08-3112-14/+69
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are some small USB fixes for 6.11-rc6. Included in here are: - dwc3 driver fixes for reported issues - MAINTAINER file update, marking a driver as unsupported :( - cdnsp driver fixes - USB gadget driver fix - USB sysfs fix - other tiny fixes - new device ids for usb serial driver All of these have been in linux-next this week with no reported issues" * tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: serial: option: add MeiG Smart SRM825L usb: cdnsp: fix for Link TRB with TC usb: dwc3: st: add missing depopulate in probe error path usb: dwc3: st: fix probed platform device ref count on probe error path usb: dwc3: ep0: Don't reset resource alloc flag (including ep0) usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes() usb: typec: fsa4480: Relax CHIP_ID check usb: dwc3: xilinx: add missing depopulate in probe error path usb: dwc3: omap: add missing depopulate in probe error path dt-bindings: usb: microchip,usb2514: Fix reference USB device schema usb: gadget: uvc: queue pump work in uvcg_video_enable() cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function usb: dwc3: core: Prevent USB core invalid event buffer address access MAINTAINERS: Mark UVC gadget driver as orphan
| | * \ Merge tag 'usb-serial-6.11-rc6' of ↵Greg Kroah-Hartman2024-08-301-0/+5
| | |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial device id for 6.11-rc6 Here's a new modem device id. This one has been in linux-next with no reported issues. * tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add MeiG Smart SRM825L
| | | * | USB: serial: option: add MeiG Smart SRM825LZHANG Yuntian2024-08-271-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for MeiG Smart SRM825L which is based on Qualcomm 315 chip. T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=2dee ProdID=4d22 Rev= 4.14 S: Manufacturer=MEIG S: Product=LTE-A Module S: SerialNumber=6f345e48 C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms Signed-off-by: ZHANG Yuntian <yt@radxa.com> Link: https://lore.kernel.org/0041DFA5200EFB1B+20240803074619.563116-1-yt@radxa.com/ Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>
| | * | | usb: cdnsp: fix for Link TRB with TCPawel Laszczak2024-08-242-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Stop Endpoint command on LINK TRB with TC bit set to 1 causes that internal cycle bit can have incorrect state after command complete. In consequence empty transfer ring can be incorrectly detected when EP is resumed. NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command is then on NOP TRB and internal cycle bit is not changed and have correct value. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") cc: <stable@vger.kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: st: add missing depopulate in probe error pathKrzysztof Kozlowski2024-08-221-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Depopulate device in probe error paths to fix leak of children resources. Fixes: f83fca0707c6 ("usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240814093957.37940-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: st: fix probed platform device ref count on probe error pathKrzysztof Kozlowski2024-08-221-8/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The probe function never performs any paltform device allocation, thus error path "undo_platform_dev_alloc" is entirely bogus. It drops the reference count from the platform device being probed. If error path is triggered, this will lead to unbalanced device reference counts and premature release of device resources, thus possible use-after-free when releasing remaining devm-managed resources. Fixes: f83fca0707c6 ("usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Link: https://lore.kernel.org/r/20240814093957.37940-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: ep0: Don't reset resource alloc flag (including ep0)Michael Grzeschik2024-08-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an endpoint is only assigned once. Unless the endpoint is reset, don't clear this flag. Otherwise we may set endpoint resource again, which prevents the driver from initiate transfer after handling a STALL or endpoint halt to the control endpoint. Commit f2e0eee47038 ("usb: dwc3: ep0: Don't reset resource alloc flag") was fixing the initial issue, but did this only for physical ep1. Since the function dwc3_ep0_stall_and_restart is resetting the flags for both physical endpoints, this also has to be done for ep0. Cc: stable@vger.kernel.org Fixes: b311048c174d ("usb: dwc3: gadget: Rewrite endpoint allocation flow") Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Link: https://lore.kernel.org/r/20240814-dwc3hwep0reset-v2-1-29e1d7d923ea@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in ↵Zijun Hu2024-08-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | remove_power_attributes() Device attribute group @usb3_hardware_lpm_attr_group is merged by add_power_attributes(), but it is not unmerged explicitly, fixed by unmerging it in remove_power_attributes(). Fixes: 655fe4effe0f ("usbcore: add sysfs support to xHCI usb3 hardware LPM") Cc: stable@vger.kernel.org Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: typec: fsa4480: Relax CHIP_ID checkLuca Weiss2024-08-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some FSA4480-compatible chips like the OCP96011 used on Fairphone 5 return 0x00 from the CHIP_ID register. Handle that gracefully and only fail probe when the I2C read has failed. With this the dev_dbg will print 0 but otherwise continue working. [ 0.251581] fsa4480 1-0042: Found FSA4480 v0.0 (Vendor ID = 0) Cc: stable@vger.kernel.org Fixes: e885f5f1f2b4 ("usb: typec: fsa4480: Check if the chip is really there") Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20240818-fsa4480-chipid-fix-v1-1-17c239435cf7@fairphone.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: xilinx: add missing depopulate in probe error pathKrzysztof Kozlowski2024-08-221-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Depopulate device in probe error paths to fix leak of children resources. Fixes: 53b5ff83d893 ("usb: dwc3: xilinx: improve error handling for PM APIs") Cc: stable@vger.kernel.org Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240816075409.23080-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: omap: add missing depopulate in probe error pathKrzysztof Kozlowski2024-08-221-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Depopulate device in probe error paths to fix leak of children resources. Fixes: ee249b455494 ("usb: dwc3: omap: remove IRQ_NOAUTOEN used with shared irq") Cc: stable@vger.kernel.org Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Link: https://lore.kernel.org/r/20240816075409.23080-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: gadget: uvc: queue pump work in uvcg_video_enable()Xu Yang2024-08-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit "6acba0345b68 usb:gadget:uvc Do not use worker thread to pump isoc usb requests", pump work could only be queued in uvc_video_complete() and uvc_v4l2_qbuf(). If VIDIOC_QBUF is executed before VIDIOC_STREAMON, we can only depend on uvc_video_complete() to queue pump work. However, this requires some free requests in req_ready list. If req_ready list is empty all the time, pump work will never be queued and video datas will never be pumped to usb controller. Actually, this situation could happen when run uvc-gadget with static image: $ ./uvc-gadget -i 1080p.jpg uvc.0 When capture image from this device, the user app will always block there. The issue is uvc driver has queued video buffer before streamon, but the req_ready list is empty all the time after streamon. This will queue pump work in uvcg_video_enable() to fill some request to req_ready list so the uvc device could work properly. Fixes: 6acba0345b68 ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests") Cc: stable@vger.kernel.org Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20240814112537.2608949-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI ControllerIan Ray2024-08-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | USB_DEVICE(0x1901, 0x0006) may send data before cdc_acm is ready, which may be misinterpreted in the default N_TTY line discipline. Signed-off-by: Ian Ray <ian.ray@gehealthcare.com> Acked-by: Oliver Neuku <oneukum@suse.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20240814072905.2501-1-ian.ray@gehealthcare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq functionPawel Laszczak2024-08-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Patch fixes the incorrect "stream_id" table index instead of "ep_index" used in cdnsp_get_hw_deq function. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") cc: stable@vger.kernel.org Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/PH7PR07MB95381F2182688811D5C711CEDD8D2@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | * | | usb: dwc3: core: Prevent USB core invalid event buffer address accessSelvarasu Ganesan2024-08-221-0/+8
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit addresses an issue where the USB core could access an invalid event buffer address during runtime suspend, potentially causing SMMU faults and other memory issues in Exynos platforms. The problem arises from the following sequence. 1. In dwc3_gadget_suspend, there is a chance of a timeout when moving the USB core to the halt state after clearing the run/stop bit by software. 2. In dwc3_core_exit, the event buffer is cleared regardless of the USB core's status, which may lead to an SMMU faults and other memory issues. if the USB core tries to access the event buffer address. To prevent this hardware quirk on Exynos platforms, this commit ensures that the event buffer address is not cleared by software when the USB core is active during runtime suspend by checking its status before clearing the buffer address. Cc: stable <stable@kernel.org> Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240815064836.1491-1-selvarasu.g@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | Merge tag 'scsi-fixes' of ↵Linus Torvalds2024-08-313-6/+10
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Minor fixes only. The sd.c one ignores a sync cache request if format is in progress which can happen if formatting a drive across suspend/resume" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: sd: Ignore command SYNCHRONIZE CACHE error if format in progress scsi: aacraid: Fix double-free on probe failure scsi: lpfc: Fix overflow build issue
| | * | | scsi: sd: Ignore command SYNCHRONIZE CACHE error if format in progressYihang Li2024-08-231-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If formatting a suspended disk (such as formatting with different DIF type), the disk will be resuming first, and then the format command will submit to the disk through SG_IO ioctl. When the disk is processing the format command, the system does not submit other commands to the disk. Therefore, the system attempts to suspend the disk again and sends the SYNCHRONIZE CACHE command. However, the SYNCHRONIZE CACHE command will fail because the disk is in the formatting process. This will cause the runtime_status of the disk to error and it is difficult for user to recover it. Error info like: [ 669.925325] sd 6:0:6:0: [sdg] Synchronizing SCSI cache [ 670.202371] sd 6:0:6:0: [sdg] Synchronize Cache(10) failed: Result: hostbyte=0x00 driverbyte=DRIVER_OK [ 670.216300] sd 6:0:6:0: [sdg] Sense Key : 0x2 [current] [ 670.221860] sd 6:0:6:0: [sdg] ASC=0x4 ASCQ=0x4 To solve the issue, ignore the error and return success/0 when format is in progress. Cc: stable@vger.kernel.org Signed-off-by: Yihang Li <liyihang9@huawei.com> Link: https://lore.kernel.org/r/20240819090934.2130592-1-liyihang9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * | | scsi: aacraid: Fix double-free on probe failureBen Hutchings2024-08-231-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | aac_probe_one() calls hardware-specific init functions through the aac_driver_ident::init pointer, all of which eventually call down to aac_init_adapter(). If aac_init_adapter() fails after allocating memory for aac_dev::queues, it frees the memory but does not clear that member. After the hardware-specific init function returns an error, aac_probe_one() goes down an error path that frees the memory pointed to by aac_dev::queues, resulting.in a double-free. Reported-by: Michael Gordon <m.gordon.zelenoborsky@gmail.com> Link: https://bugs.debian.org/1075855 Fixes: 8e0c5ebde82b ("[SCSI] aacraid: Newer adapter communication iterface support") Signed-off-by: Ben Hutchings <benh@debian.org> Link: https://lore.kernel.org/r/ZsZvfqlQMveoL5KQ@decadent.org.uk Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
| | * | | scsi: lpfc: Fix overflow build issueSherry Yang2024-08-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Build failed while enabling "CONFIG_GCOV_KERNEL=y" and "CONFIG_GCOV_PROFILE_ALL=y" with following error: BUILDSTDERR: drivers/scsi/lpfc/lpfc_bsg.c: In function 'lpfc_get_cgnbuf_info': BUILDSTDERR: ./include/linux/fortify-string.h:114:33: error: '__builtin_memcpy' accessing 18446744073709551615 bytes at offsets 0 and 0 overlaps 9223372036854775807 bytes at offset -9223372036854775808 [-Werror=restrict] BUILDSTDERR: 114 | #define __underlying_memcpy __builtin_memcpy BUILDSTDERR: | ^ BUILDSTDERR: ./include/linux/fortify-string.h:637:9: note: in expansion of macro '__underlying_memcpy' BUILDSTDERR: 637 | __underlying_##op(p, q, __fortify_size); \ BUILDSTDERR: | ^~~~~~~~~~~~~ BUILDSTDERR: ./include/linux/fortify-string.h:682:26: note: in expansion of macro '__fortify_memcpy_chk' BUILDSTDERR: 682 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \ BUILDSTDERR: | ^~~~~~~~~~~~~~~~~~~~ BUILDSTDERR: drivers/scsi/lpfc/lpfc_bsg.c:5468:9: note: in expansion of macro 'memcpy' BUILDSTDERR: 5468 | memcpy(cgn_buff, cp, cinfosz); BUILDSTDERR: | ^~~~~~ This happens from the commit 06bb7fc0feee ("kbuild: turn on -Wrestrict by default"). Address this issue by using size_t type. Signed-off-by: Sherry Yang <sherry.yang@oracle.com> Link: https://lore.kernel.org/r/20240821065131.1180791-1-sherry.yang@oracle.com Reviewed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-01-15 14:21:10 +0100