| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Each of qcom,spmi-adc7-pm*.h headers define a set of ADC channels that
can be used for monitoring on thie particular chip. Switch them to use
channel IDs defined in the dt-bindings/iio/qcom,spmi-vadc.h header
instead of specifying the numeric IDs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As per the new ADC7 architecture used by the Qualcomm PMICs, each PMIC
has the static Slave ID (SID) assigned by default. The primary PMIC
PMK8350 is responsible for collecting the temperature/voltage data from
the slave PMICs and exposing them via it's registers.
For getting the measurements from the slave PMICs, PMK8350 uses the
channel ID encoded with the SID of the relevant PMIC. So far, the
dt-binding for the slave PMIC PM8350 assumed that there will be only
one PM8350 in a system. So it harcoded SID 1 with channel IDs.
But this got changed in platforms such as Lenovo X13s where there are a
couple of PM8350 PMICs available. So to address multiple PM8350s, change
the binding to accept the SID specified by the user and use it for
encoding the channel ID.
It should be noted that, even though the SID is static it is not
globally unique. Only the primary PMIC has the unique SID id 0.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221103095810.64606-2-manivannan.sadhasivam@linaro.org
|
|
|
Add documentation for PMIC7 ADC peripheral.
For the PMIC7-type PMICs, ADC peripheral is present in HW for the
following PMICs: PMK8350, PM8350, PM8350b, PMR735a and PMR735b.
Of these, only the ADC peripheral on PMK8350 is exposed directly to SW.
If SW needs to communicate with ADCs on other PMICs, it specifies the
PMIC to PMK8350 through the newly added SID register and communication
between PMK8350 ADC and other PMIC ADCs is carried out through
PBS(Programmable Boot Sequence) at the firmware level.
In addition, add definitions for ADC channels and virtual channel
definitions (combination of ADC channel number and PMIC SID number)
per PMIC, to be used by ADC clients for PMIC7.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
