summaryrefslogtreecommitdiffstats
path: root/net/mac80211/main.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2018-06-161-6/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking fixes from David Miller: 1) Various netfilter fixlets from Pablo and the netfilter team. 2) Fix regression in IPVS caused by lack of PMTU exceptions on local routes in ipv6, from Julian Anastasov. 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia. 4) Don't crash on poll in TLS, from Daniel Borkmann. 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things including Avahi mDNS. From Bart Van Assche. 6) Missing of_node_put in qcom/emac driver, from Yue Haibing. 7) We lack checking of the TCP checking in one special case during SYN receive, from Frank van der Linden. 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg. 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman. 10) Must grab HW caps before doing quirk checks in stmmac driver, from Jose Abreu. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits) net: stmmac: Run HWIF Quirks after getting HW caps neighbour: skip NTF_EXT_LEARNED entries during forced gc net: cxgb3: add error handling for sysfs_create_group tls: fix waitall behavior in tls_sw_recvmsg tls: fix use-after-free in tls_push_record l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl() l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels mlxsw: spectrum_switchdev: Fix port_vlan refcounting mlxsw: spectrum_router: Align with new route replace logic mlxsw: spectrum_router: Allow appending to dev-only routes ipv6: Only emit append events for appended routes stmmac: added support for 802.1ad vlan stripping cfg80211: fix rcu in cfg80211_unregister_wdev mac80211: Move up init of TXQs mac80211_hwsim: fix module init error paths cfg80211: initialize sinfo in cfg80211_get_station nl80211: fix some kernel doc tag mistakes hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload rds: avoid unenecessary cong_update in loop transport l2tp: clean up stale tunnel or session in pppol2tp_connect's error path ...
| * mac80211: Move up init of TXQsToke Høiland-Jørgensen2018-06-151-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | On init, ieee80211_if_add() dumps the interface. Since that now includes a dump of the TXQ state, we need to initialise that before the dump happens. So move up the TXQ initialisation to to before the call to ieee80211_if_add(). Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace") Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* | treewide: kmalloc() -> kmalloc_array()Kees Cook2018-06-131-1/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* mac80211: Support the new cfg80211 TXQ stats APIToke Høiland-Jørgensen2018-05-081-0/+3
| | | | | | | | This adds support to mac80211 to export TXQ stats via the newly added cfg80211 API. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Send control port frames over nl80211Denis Kenzior2018-03-291-0/+2
| | | | | | | | | | | | If userspace requested control port frames to go over 80211, then do so. The control packets are intercepted just prior to delivery of the packet to the underlying network device. Pre-authentication type frames (protocol: 0x88c7) are also forwarded over nl80211. Signed-off-by: Denis Kenzior <denkenz@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: allow AP_VLAN operation on crypto controlled devicesManikanta Pubbisetty2018-03-291-2/+6
| | | | | | | | | | | | | | | | | | | | In the current implementation, mac80211 advertises the support of AP_VLANs based on the driver's support for AP mode; it also blocks encrypted AP_VLAN operation on devices advertising SW_CRYPTO_CONTROL. The implementation seems weird in it's current form and could be often confusing, this is because there can be drivers advertising both SW_CRYPTO_CONTROL and AP mode support (ex: ath10k) in which case AP_VLAN will still be supported but only in open BSS and not in secured BSS. When SW_CRYPTO_CONTROL is enabled, it makes more sense if the decision to support AP_VLANs is left to the driver. Mac80211 can then allow AP_VLAN operations depending on the driver support. Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Revert "mac80211: Add TXQ scheduling API"Johannes Berg2017-12-191-3/+0
| | | | | | | | | | This reverts commit e937b8da5a591f141fe41aa48a2e898df9888c95. Turns out that a new driver (mt76) is coming in through Kalle's tree, and will conflict with this. It also has some conflicting requirements, so we'll revisit this later. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Revert "mac80211: Add airtime account and scheduling to TXQs"Johannes Berg2017-12-191-2/+1
| | | | | | | | | This reverts commit b0d52ad821843a6c5badebd80feef9f871904fa6. We need to revert the TXQ scheduling API due to conflicts with a new driver, and this depends on that API. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Add airtime account and scheduling to TXQsToke Høiland-Jørgensen2017-12-111-1/+2
| | | | | | | | | | | | | | | | | This adds airtime accounting and scheduling to the mac80211 TXQ scheduler. A new hardware flag, AIRTIME_ACCOUNTING, is added that drivers can set if they support reporting airtime usage of transmissions. When this flag is set, mac80211 will expect the actual airtime usage to be reported in the tx_time and rx_time fields of the respective status structs. When airtime information is present, mac80211 will schedule TXQs (through ieee80211_next_txq()) in a way that enforces airtime fairness between active stations. This scheduling works the same way as the ath9k in-driver airtime fairness scheduling. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Add TXQ scheduling APIToke Høiland-Jørgensen2017-12-111-0/+3
| | | | | | | | | | | | | | | | | | | | This adds an API to mac80211 to handle scheduling of TXQs and changes the interface between driver and mac80211 for TXQ handling as follows: - The wake_tx_queue callback interface no longer includes the TXQ. Instead, the driver is expected to retrieve that from ieee80211_next_txq() - Two new mac80211 functions are added: ieee80211_next_txq() and ieee80211_schedule_txq(). The former returns the next TXQ that should be scheduled, and is how the driver gets a queue to pull packets from. The latter is called internally by mac80211 to start scheduling a queue, and the driver is supposed to call it to re-schedule the TXQ after it is finished pulling packets from it (unless the queue emptied). The ath9k and ath10k drivers are changed to use the new API. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: call synchronize_net once in the restart flowSara Sharon2017-12-111-0/+3
| | | | | | | | | | | | | | | | | | | Currently the restart flow enables RX back, and then proceeds to tear down RX and TX aggregations. The TX aggregation tear down calls synchronize_net(), which waits for packet receiving to be done. This is done for every session, while RX processing is already active, and in some reproductions it takes up to 3 seconds. Add a call once in the restart_work, before we have traffic active again, and remove the subsequent calls when tearing down the aggregation. This requires to move down the code that turns off the reconfig flag in order to be able to test it in _ieee80211_stop_tx_ba_session(). Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Convert timers to use timer_setup()Kees Cook2017-11-201-2/+1
| | | | | | | | | | | | | In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: disentangle iflist_mtx and chanctx_mtxJohannes Berg2017-04-261-0/+2
| | | | | | | | | | | | | | | At least on iwlwifi, sometimes lockdep complains that we can lock chanctx_mtx -> mvm.mutex -> iflist_mtx (due to iterate_interfaces) and iflist_mtx -> chanctx_mtx Remove the latter dependency in mac80211 by using the RTNL that we already hold in one case, and can relatively easily achieve in the other case. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: keep a separate list of monitor interfaces that are upJohannes Berg2017-04-181-0/+1
| | | | | | | | | In addition to keeping monitor interfaces on the regular list of interfaces, keep those that are up and not in cooked mode on a separate list. This saves having to iterate all interfaces when delivering to monitor interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: initialize SMPS field in HT capabilitiesFelix Fietkau2017-01-131-4/+9
| | | | | | | | | | | | | | | | | | ibss and mesh modes copy the ht capabilites from the band without overriding the SMPS state. Unfortunately the default value 0 for the SMPS field means static SMPS instead of disabled. This results in HT ibss and mesh setups using only single-stream rates, even though SMPS is not supposed to be active. Initialize SMPS to disabled for all bands on ieee80211_hw_register to ensure that the value is sane where it is not overriden with the real SMPS state. Reported-by: Elektra Wagenrad <onelektra@gmx.net> Signed-off-by: Felix Fietkau <nbd@nbd.name> [move VHT TODO comment to a better place] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Claim Fast Initial Link Setup (FILS) STA supportJouni Malinen2016-10-271-0/+1
| | | | | | | | | | With the previous commits, initial FILS authentication/association support is now functional in mac80211-based drivers for station role (and FILS AP case is covered by user space in hostapd withotu requiring mac80211 changes). Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add a HW flag for supporting HW TX fragmentationSara Sharon2016-10-191-0/+4
| | | | | | | | | | | | | | | Currently mac80211 determines whether HW does fragmentation by checking whether the set_frag_threshold callback is set or not. However, some drivers may want to set the HW fragmentation capability depending on HW generation. Allow this by checking a HW flag instead of checking the callback. Signed-off-by: Sara Sharon <sara.sharon@intel.com> [added the flag to ath10k and wlcore] Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Implement add_nan_func and rm_nan_funcAyala Beker2016-09-301-0/+3
| | | | | | | | | | | Implement add/rm_nan_func functions and handle NAN function termination notifications. Handle instance_id allocation for NAN functions and implement the reconfig flow. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add boilerplate code for start / stop NANAyala Beker2016-09-301-0/+5
| | | | | | | | | | | This code doesn't do much besides allowing to start and stop the vif. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add support for radiotap timestamp fieldJohannes Berg2016-09-121-0/+3
| | | | | | | | | | | Use the existing device timestamp from the RX status information to add support for the new radiotap timestamp field. Currently only 32-bit counters are supported, but we also add the radiotap mactime where applicable. This new field allows more flexibility in where the timestamp is taken etc. The non-timestamp data in the field is taken from a new field in the hw struct. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: implement fair queueing per txqMichal Kazior2016-06-091-0/+7
| | | | | | | | | | | | | | | | | | | | | mac80211's software queues were designed to work very closely with device tx queues. They are required to make use of 802.11 packet aggregation easily and efficiently. Due to the way 802.11 aggregation is designed it only makes sense to keep fair queuing as close to hardware as possible to reduce induced latency and inertia and provide the best flow responsiveness. This change doesn't translate directly to immediate and significant gains. End result depends on driver's induced latency. Best results can be achieved if driver keeps its own tx queue/fifo fill level to a minimum. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: skip netdev queue control with software queuingMichal Kazior2016-06-091-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qdiscs are designed with no regard to 802.11 aggregation requirements and hand out packet-by-packet with no guarantee they are destined to the same tid. This does more bad than good no matter how fairly a given qdisc may behave on an ethernet interface. Software queuing used per-AC netdev subqueue congestion control whenever a global AC limit was hit. This meant in practice a single station or tid queue could starve others rather easily. This could resonate with qdiscs in a bad way or could just end up with poor aggregation performance. Increasing the AC limit would increase induced latency which is also bad. Disabling qdiscs by default and performing taildrop instead of netdev subqueue congestion control on the other hand makes it possible for tid queues to fill up "in the meantime" while preventing stations starving each other. This increases aggregation opportunities and should allow software queuing based drivers achieve better performance by utilizing airtime more efficiently with big aggregates. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: remove enum ieee80211_bandJohannes Berg2016-04-121-3/+3
| | | | | | | | | This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add NETIF_F_RXCSUM to features white listSara Sharon2016-04-051-1/+1
| | | | | | | | | | NETIF_F_RXCSUM is not in the white list, though some drivers may want to set it in order to enable seeing the actual RX checksum status in ethtool. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Set global RRM capabilityEmmanuel Grumbach2016-04-051-0/+2
| | | | | | | | Allow publishing RRM capabilities for features that are not HW dependent. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: handle sched_scan_stopped vs. hw restart raceEliad Peller2016-01-141-0/+1
| | | | | | | | | | | | | | | | | | On hw restart, mac80211 might try to reconfigure already stopped sched scan, if ieee80211_sched_scan_stopped_work() wasn't scheduled yet. This in turn will keep the device driver with scheduled scan configured, while both mac80211 and cfg80211 will clear their sched scan state once the work is scheduled. Fix it by ignoring ieee80211_sched_scan_stopped() calls while in hw restart, and flush the work before starting the reconfiguration. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: avoid ROC during hw restartEliad Peller2016-01-141-0/+5
| | | | | | | | | | Defer ROC requests during hw restart, as the driver might not be fully configured in this stage (e.g. channel contexts were not added yet) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: rewrite remain-on-channel logicJohannes Berg2015-12-041-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jouni found a bug in the remain-on-channel logic: when a short item is queued, a long item is combined with it extending the original one, and then the long item is deleted, the timeout doesn't go back to the short one, and the short item ends up taking a long time. In this case, this showed as blocking scan when running two test cases back to back - the scan from the second was delayed even though all the remain-on-channel items should long have been gone. Fixing this with the current data structures turns out to be a bit complicated, we just remove the long item from the dependents list right now and don't recalculate the timeouts. There's a somewhat similar bug where we delete the short item and all the dependents go with it; to fix this we'd have to move them from the dependents to the real list. Instead of trying to do that, rewrite the code to not have all this complexity in the data structures: use a single list and allow more than one entry in it being marked as started. This makes the code a bit more complex, the worker needs to understand that it might need to just remove one of the started items, while keeping the device off-channel, but that's not more complicated than the nested data structures. This then fixes both issues described, and makes it easier to also limit the overall off-channel time when combining. TODO: as before, with hardware remain-on-channel, deleting an item after combining results in cancelling them all - we can keep track of the time elapsed and only cancel after that to fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Revert "mac80211: don't advertise NL80211_FEATURE_FULL_AP_CLIENT_STATE"Johannes Berg2015-12-041-1/+2
| | | | | | | This reverts commit 45bb780a2147b9995f3d288c44ecb87ca8a330e2, the previous two patches fixed the functionality. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: don't advertise NL80211_FEATURE_FULL_AP_CLIENT_STATEJohannes Berg2015-11-171-2/+1
| | | | | | | | | | | | For now, this feature doesn't actually work. To avoid shipping a kernel that has it enabled but where it can't be used disable it for now - we can re-enable it when it's fixed. This partially reverts 44674d9c2267 ("mac80211: advertise support for full station state in AP mode"). Cc: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use freezable workqueue for restart workEliad Peller2015-11-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Requesting hw restart during suspend might result in the restart work being executed after mac80211 and the hw are suspended. Solve the race by simply scheduling the restart work on a freezable workqueue. Note that there can be some cases of reconfiguration on resume (besides the hardware restart): * wowlan is not configured - All the interfaces removed were removed on suspend, and drv_stop() was called. At this point the driver shouldn't expect for hw_restart anyway, so we can simply cancel it (on resume). * wowlan is configured, drv_resume() == 1 There is no definitive expected behavior in this case, as each driver might have different expectations (e.g. setting some flags on suspend/restart vs. not handling spurious recovery). For now, simply let the hw_restart work run again after resume, and hope the driver will handle it well (or at least initiate another hw restart). Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove cfg.hJohannes Berg2015-10-141-1/+0
| | | | | | | The file contains just a single declaration that can easily move to another file - remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove PM-QoS listenerJohannes Berg2015-10-141-13/+0
| | | | | | | | | | As this API has never really seen any use and most drivers don't ever use the value derived from it, remove it. Change the only driver using it (rt2x00) to simply use the DTIM period instead of the "max sleep" time. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: advertise support for full station state in AP modeAyala Beker2015-09-291-1/+2
| | | | | | | | | | | | | This enables adding stations in unauthenticated mode, just after receiving the first authentication frame; which in turn allows sending a negative authentication reply if the station cannot be added. In addition init rate control for unassociated station only when it becomes associated, prior to that low rates will be used. Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: TDLS: handle chan-switch in RTNL locked workArik Nemtsov2015-07-171-0/+5
| | | | | | | | | | | | Move TDLS channel-switch Rx handling into an RTNL locked work. This is required to add proper regulatory checking to incoming channel-switch requests. Queue incoming requests in a dedicated skb queue and handle the request in a device-specific work to avoid deadlocking on interface removal. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: don't store napi structJohannes Berg2015-07-171-12/+0
| | | | | | | | | | | | | | When introducing multiple RX queues, a single NAPI struct will not be sufficient. Instead of trying to store multiple, simply change the API to have the NAPI struct passed to the RX function. This of course means that drivers using rx_irqsafe() cannot use NAPI, but that seems a reasonable trade-off, particularly since only two of all drivers are currently using it at all. While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag again since this code path cannot have a napi struct anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: convert HW flags to unsigned long bitmapJohannes Berg2015-06-101-7/+7
| | | | | | | | | | | | | | | As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: prevent possible crypto tx tailroom corruptionMichal Kazior2015-05-291-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There was a possible race between ieee80211_reconfig() and ieee80211_delayed_tailroom_dec(). This could result in inability to transmit data if driver crashed during roaming or rekeying and subsequent skbs with insufficient tailroom appeared. This race was probably never seen in the wild because a device driver would have to crash AND recover within 0.5s which is very unlikely. I was able to prove this race exists after changing the delay to 10s locally and crashing ath10k via debugfs immediately after GTK rekeying. In case of ath10k the counter went below 0. This was harmless but other drivers which actually require tailroom (e.g. for WEP ICV or MMIC) could end up with the counter at 0 instead of >0 and introduce insufficient skb tailroom failures because mac80211 would not resize skbs appropriately anymore. Fixes: 8d1f7ecd2af5 ("mac80211: defer tailroom counter manipulation when roaming") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix memory leakJohannes Berg2015-05-201-1/+3
| | | | | | | | | My recent change here introduced a possible memory leak if the driver registers an invalid cipher schemes. This won't really happen in practice, but fix the leak nonetheless. Fixes: e3a55b5399d55 ("mac80211: validate cipher scheme PN length better") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: validate cipher scheme PN length betterJohannes Berg2015-05-061-1/+4
| | | | | | | | | | | | | | Currently, a cipher scheme can advertise an arbitrarily long sequence counter, but mac80211 only supports up to 16 bytes and the initial value from userspace will be truncated. Fix two things: * don't allow the driver to register anything longer than the 16 bytes that mac80211 reserves space for * require userspace to specify a starting value with the correct length (or none at all) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: make LED triggering depend on activationJohannes Berg2015-05-051-1/+3
| | | | | | | | | | | | | | | | When LED triggers are compiled in, but not used, mac80211 will still call them to update the status. This isn't really a problem for the assoc and radio ones, but the TX/RX (and to a certain extend TPT) ones can be called very frequently (for every packet.) In order to avoid that when they're not used, track their activation and call the corresponding trigger (and in the TPT case, account for throughput) only when the trigger is actually used by an LED. Additionally, make those trigger functions inlines since theyre only used once in the remaining code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove support for IFF_PROMISCJohannes Berg2015-04-241-3/+0
| | | | | | | | | | | This support is essentially useless as typically networks are encrypted, frames will be filtered by hardware, and rate scaling will be done with the intended recipient in mind. For real monitoring of the network, the monitor mode support should be used instead. Removing it removes a lot of corner cases. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: allow segmentation offloadsJohannes Berg2015-04-221-1/+2
| | | | | | | | Implement the necessary software segmentation on the normal TX path so that fast-xmit can use segmentation offload if the hardware (or driver) supports it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: allow drivers to support S/GJohannes Berg2015-04-221-1/+1
| | | | | | | | | | | | | | | If drivers want to support S/G (really just gather DMA on TX) then we can now easily support this on the fast-xmit path since it just needs to write to the ethernet header (and already has a check for that being possible.) However, disallow this on the regular TX path (which has to handle fragmentation, software crypto, etc.) by calling skb_linearize(). Also allow the related HIGHDMA since that's not interesting to the code in mac80211 at all anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add an intermediate software queue implementationFelix Fietkau2015-04-011-0/+3
| | | | | | | | | | | | | | | | | | This allows drivers to request per-vif and per-sta-tid queues from which they can pull frames. This makes it easier to keep the hardware queues short, and to improve fairness between clients and vifs. The task of scheduling packet transmission is left up to the driver - queueing is controlled by mac80211. Drivers can only dequeue packets by calling ieee80211_tx_dequeue. This makes it possible to add active queue management later without changing drivers using this code. This can also be used as a starting point to implement A-MSDU aggregation in a way that does not add artificially induced latency. Signed-off-by: Felix Fietkau <nbd@openwrt.org> [resolved minor context conflict, minor changes, endian annotations] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use rhashtable for station tableJohannes Berg2015-04-011-3/+6
| | | | | | | | | | | | | | | | | | | | | | We currently have a hand-rolled table with 256 entries and are using the last byte of the MAC address as the hash. This hash is obviously very fast, but collisions are easily created and we waste a lot of space in the common case of just connecting as a client to an AP where we just have a single station. The other common case of an AP is also suboptimal due to the size of the hash table and the ease of causing collisions. Convert all of this to use rhashtable with jhash, which gives us the advantage of a far better hash function (with random perturbation to avoid hash collision attacks) and of course that the hash table grows and shrinks dynamically with chain length, improving both cases above. Use a specialised hash function (using jhash, but with fixed length) to achieve better compiler optimisation as suggested by Sergey Ryazanov. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: pass name_assign_type to rdev_add_virtual_intf()Tom Gundersen2015-03-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | This will expose in /sys whether the ifname of a device is set by userspace or generated by the kernel. The latter kind (wlanX, etc) is not deterministic, so userspace needs to rename these devices to names that are guaranteed to stay the same between reboots. The former, however should never be renamed, so userspace needs to be able to reliably tell the difference. Similar functionality was introduced for the rtnetlink core in commit 5517750f058e ("net: rtnetlink - make create_link take name_assign_type") Signed-off-by: Tom Gundersen <teg@jklm.no> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: Johannes Berg <johannes@sipsolutions.net> [reformat changelog to fit 72 cols] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove TX latency measurement codeJohannes Berg2015-02-281-2/+0
| | | | | | | | | | | | | | | | Revert commit ad38bfc916da ("mac80211: Tx frame latency statistics") (along with some follow-up fixes). This code turned out not to be as useful in the current form as we thought, and we've internally hacked it up more, but that's not very suitable for upstream (for now), and we might just do that with tracing instead. Therefore, for now at least, remove this code. We might also need to use the skb->tstamp field for the TCP performance issue, which is more important than the debugging. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80111: Add BIP-GMAC-128 and BIP-GMAC-256 ciphersJouni Malinen2015-01-271-3/+9
| | | | | | | | | This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the driver and also use software-implementation within mac80211 when the driver does not support this with hardware accelaration. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80111: Add BIP-CMAC-256 cipherJouni Malinen2015-01-271-5/+8
| | | | | | | | | This allows mac80211 to configure BIP-CMAC-256 to the driver and also use software-implementation within mac80211 when the driver does not support this with hardware accelaration. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-30 22:09:04 +0100