summaryrefslogtreecommitdiffstats
path: root/net/mac80211/offchannel.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* wifi: mac80211: expand ieee80211_mgmt_tx() for MLOJohannes Berg2022-07-221-14/+33
| | | | | | | | | | | | | | | There are a couple of new things that should be possible with MLO: * selecting the link to transmit to a station by link ID, which a previous patch added to the nl80211 API * selecting the link by frequency, similarly * allowing transmittion to an MLD without specifying any channel or link ID, with MLD addresses Enable these use cases. Also fix the address comparison in client mode to use the AP (MLD) address. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: RCU-ify link/link_conf pointersJohannes Berg2022-07-151-5/+10
| | | | | | | | | | Since links can be added and removed dynamically, we need to somehow protect the sdata->link[] and vif->link_conf[] array pointers from disappearing when accessing them without locks. RCU-ify the pointers to achieve this, which requires quite a bit of rework. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: Consider MLO links in offchannel logicAndrei Otcheretianski2022-07-151-2/+16
| | | | | | | Check all the MLO links to decide whether offchannel TX is needed. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: split bss_info_changed methodJohannes Berg2022-06-201-4/+4
| | | | | | | | | Split the bss_info_changed method to vif_cfg_changed and link_info_changed, with the latter getting a link ID. Also change the 'changed' parameter to u64 already, we know we need that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: reorg some iface data structs for MLDJohannes Berg2022-06-201-3/+3
| | | | | | | | | | Start reorganizing interface related data structures toward MLD. The most complex part here is for the keys, since we have to split the various kinds of GTKs off to the link but still need to use (for WEP) the other keys as a fallback even for multicast frames. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: move interface config to new structJohannes Berg2022-06-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We'll use bss_conf for per-link configuration later, so move out all the non-link-specific data out into a new struct ieee80211_vif_cfg used in the vif. Some adjustments were done with the following spatch: @@ expression sdata; struct ieee80211_vif *vifp; identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator }; @@ ( -sdata->vif.bss_conf.var +sdata->vif.cfg.var | -vifp->bss_conf.var +vifp->cfg.var ) @bss_conf@ struct ieee80211_bss_conf *bss_conf; identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator }; @@ -bss_conf->var +vif_cfg->var (though more manual fixups were needed, e.g. replacing "vif_cfg->" by "vif->cfg." in many files.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wifi: mac80211: move some future per-link data to bss_confJohannes Berg2022-06-201-3/+3
| | | | | | | | | | | | | | | | | | | | | | | To add MLD, reuse the bss_conf structure later for per-link information, so move some things into it that are per link. Most transformations were done with the following spatch: @@ expression sdata; identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color }; @@ -sdata->vif.var +sdata->vif.bss_conf.var @@ struct ieee80211_vif *vif; identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color }; @@ -vif->var +vif->bss_conf.var Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use ifmgd->bssid instead of ifmgd->associated->bssidJohannes Berg2022-05-161-1/+1
| | | | | | | | Since we always track the BSSID there when we get associated, these are equivalent, but ifmgd->bssid saves a dereference and thus makes the code a bit smaller, and more readable. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Inform AP when returning operating channelLoic Poulain2020-09-281-29/+9
| | | | | | | | | | | | | | | Because we can miss AP wakeup (beacon) while scanning other channels, it's better go into wakeup state and inform the AP of that upon returning to the operating channel, rather than staying asleep and waiting for the next TIM indicating traffic for us. This saves precious time, especially when we only have 200ms inter- scan period for monitoring the active connection. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org [rewrite commit message a bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: rename csa counters to countdown countersJohn Crispin2020-08-271-1/+1
| | | | | | | | | We want to reuse the functions and structs for other counters such as BSS color change. Rename them to more generic names. Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove unused flags argument in transmit functionsMathy Vanhoef2020-07-311-1/+1
| | | | | | | | | The flags argument in transmit functions is no longer being used and can be removed. Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be> Link: https://lore.kernel.org/r/20200723100153.31631-5-Mathy.Vanhoef@kuleuven.be Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Use fallthrough pseudo-keywordGustavo A. R. Silva2020-07-311-2/+2
| | | | | | | | | | | | Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://lore.kernel.org/r/20200707204548.GA9320@embeddedor Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: handle channel frequency offsetThomas Pedersen2020-04-241-0/+4
| | | | | | | | | | | | | | | | | | | | cfg80211_chan_def and ieee80211_channel recently gained a frequency offset component. Handle this where it makes sense (potentially required by S1G channels). For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a channel with frequency offset is passed, since they may or may not work. Once someone tests and verifies these commands work on thos types of channels, we can remove that error. join_ocb and join_mesh look harmless because they use a simple ieee80211_vif_use_channel(), which is using an already verified channel, so we let those through. Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: pass the vif to cancel_remain_on_channelEmmanuel Grumbach2019-07-261-2/+3
| | | | | | | | | | | This low level driver can find it useful to get the vif when a remain on channel session is cancelled. iwlwifi will need this soon. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-06-221-4/+1
|\ | | | | | | | | | | Minor SPDX change conflict. Signed-off-by: David S. Miller <davem@davemloft.net>
| * treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner2019-06-191-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | mac80211: notify offchannel expire on mgmt_txJames Prestwood2019-06-141-0/+4
|/ | | | | | | When the offchannel TX wait time expires, send the appropriate event. Signed-off-by: James Prestwood <james.prestwood@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: support scan features for improved scan privacyJohannes Berg2018-06-151-1/+1
| | | | | | | | | | Support the new random SN and minimal probe request contents scan flags for the case of software scan - for hardware scan the drivers need to opt in, but may need to do only that, depending on their implementation. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* mac80211: mark expected switch fall-throughsGustavo A. R. Silva2017-12-111-2/+2
| | | | | | | | | | | | In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Notice that in some cases I replaced "fall through on else" and "otherwise fall through" comments with just a "fall through" comment, which is what GCC is expecting to find. Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: flush hw_roc_start work before cancelling the ROCAvraham Stern2017-09-051-0/+2
| | | | | | | | | | | | | | | | | | | | | | | When HW ROC is supported it is possible that after the HW notified that the ROC has started, the ROC was cancelled and another ROC was added while the hw_roc_start worker is waiting on the mutex (since cancelling the ROC and adding another one also holds the same mutex). As a result, the hw_roc_start worker will continue to run after the new ROC is added but before it is actually started by the HW. This may result in notifying userspace that the ROC has started before it actually does, or in case of management tx ROC, in an attempt to tx while not on the right channel. In addition, when the driver will notify mac80211 that the second ROC has started, mac80211 will warn that this ROC has already been notified. Fix this by flushing the hw_roc_start work before cancelling an ROC. Cc: stable@vger.kernel.org Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* networking: introduce and use skb_put_data()Johannes Berg2017-06-161-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211: fix CMD_FRAME for AP_VLANMichael Braun2016-10-121-1/+1
| | | | | | | | | | | | | | | | | | When using IEEE 802.11r FT OVER-DS roaming with AP_VLAN, hostapd needs to send out a frame using CMD_FRAME for a station assigned to an AP_VLAN interface. Right now, the userspace needs to give the exact AP_VLAN interface index for CMD_FRAME; hostapd does not do this. Additionally, userspace cannot use GET_STATION to query the AP_VLAN ifidx, as while GET_STATION finds stations assigned to AP_VLAN even if the AP iface is queried, it does not return AP_VLAN ifidx (it returns the queried one). This breaks IEEE 802.11r over_ds with vlans, as the reply frame does not get out. This patch fixes this by using get_sta_bss for CMD_FRAME. Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add boilerplate code for start / stop NANAyala Beker2016-09-301-1/+2
| | | | | | | | | | | This code doesn't do much besides allowing to start and stop the vif. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: add start / stop NAN commandsAyala Beker2016-09-301-0/+1
| | | | | | | | | | | | | | | | | This allows user space to start/stop NAN interface. A NAN interface is like P2P device in a few aspects: it doesn't have a netdev associated to it. Add the new interface type and prevent operations that can't be executed on NAN interface like scan. Define several attributes that may be configured by user space when starting NAN functionality (master preference and dual band operation) Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: avoid ROC during hw restartEliad Peller2016-01-141-0/+4
| | | | | | | | | | Defer ROC requests during hw restart, as the driver might not be fully configured in this stage (e.g. channel contexts were not added yet) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix remain-on-channel cancellationJohannes Berg2016-01-141-2/+4
| | | | | | | | | | | | | Ilan's previous commit 1b894521e60c ("mac80211: handle HW ROC expired properly") neglected to take into account that hw_begun was now always set in the software implementation as well as the offloaded case. Fix hw_begun to only apply to the offloaded case to make the check in Ilan's commit safe and correct. Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: recalculate SW ROC only when neededJohannes Berg2016-01-141-5/+1
| | | | | | | | | | | | | | | | | | | | The current (new) code recalculates the new work timeout for software remain-on-channel whenever any item started. In two of the callers of ieee80211_handle_roc_started(), this is completely pointless since they're for hardware and will skip the recalculation entirely; it's necessary only in the case of having just added a new item to the list, as in the last remaining case the recalculation had just been done. This last case, however, is also problematic - if one of the items on the list actually expires during the recalc the list iteration outside becomes corrupted and crashes. Fix this by moving the recalculation to the only place where it's required. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: handle HW ROC expired properlyIlan Peer2015-12-071-1/+5
| | | | | | | | | | | | | | In case of HW ROC, when the driver reports that the ROC expired, it is not sufficient to purge the ROCs based on the remaining time, as it possible that the device finished the ROC session before the actual requested duration. To handle such cases, in case of ROC expired notification from the driver, complete all the ROCs which are marked with hw_begun, regardless of the remaining duration. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: reject zero cookie in mgmt-tx/roc cancelJohannes Berg2015-12-041-0/+3
| | | | | | | | | | | | | | | When cancelling, you can cancel "any" (first in list) mgmt-tx or remain-on-channel operation by using the value 0 for the cookie along with the *opposite* operation, i.e. * cancel the first mgmt-tx by cancelling roc with 0 cookie * cancel the first roc by cancelling mgmt-tx with 0 cookie This isn't really that bad since userspace should only pass cookies that we gave it, but could lead to hard-to-debug issues so better prevent it and reject zero values since we never hand those out. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: rewrite remain-on-channel logicJohannes Berg2015-12-041-286/+313
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jouni found a bug in the remain-on-channel logic: when a short item is queued, a long item is combined with it extending the original one, and then the long item is deleted, the timeout doesn't go back to the short one, and the short item ends up taking a long time. In this case, this showed as blocking scan when running two test cases back to back - the scan from the second was delayed even though all the remain-on-channel items should long have been gone. Fixing this with the current data structures turns out to be a bit complicated, we just remove the long item from the dependents list right now and don't recalculate the timeouts. There's a somewhat similar bug where we delete the short item and all the dependents go with it; to fix this we'd have to move them from the dependents to the real list. Instead of trying to do that, rewrite the code to not have all this complexity in the data structures: use a single list and allow more than one entry in it being marked as started. This makes the code a bit more complex, the worker needs to understand that it might need to just remove one of the started items, while keeping the device off-channel, but that's not more complicated than the nested data structures. This then fixes both issues described, and makes it easier to also limit the overall off-channel time when combining. TODO: as before, with hardware remain-on-channel, deleting an item after combining results in cancelling them all - we can keep track of the time elapsed and only cancel after that to fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: simplify ack_skb handlingJohannes Berg2015-12-041-5/+3
| | | | | | | | | | Since the cookie is assigned inside ieee80211_make_ack_skb() now, we no longer need to return the ack_skb as the cookie and can simplify the function's return and the callers. Also rename it to ieee80211_attach_ack_skb() to more accurately reflect its purpose. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: move off-channel/mgmt-tx code to offchannel.cJohannes Berg2015-12-041-3/+471
| | | | | | | This is quite a bit of code that logically depends here since it has to deal with all the remain-on-channel logic. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix mgmt-tx abort cookie and leakJohannes Berg2015-12-041-3/+2
| | | | | | | | | | If a mgmt-tx operation is aborted before it runs, the wrong cookie is reported back to userspace, and the ack_skb gets leaked since the frame is freed directly instead of freeing it using ieee80211_free_txskb(). Fix that. Fixes: 3b79af973cf4 ("mac80211: stop using pointers as userspace cookies") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use bool argument to ieee80211_send_nullfuncJohannes Berg2015-09-291-3/+3
| | | | | | | Instead of int with 0/1, use bool with false/true for the powersave argument to ieee80211_send_nullfunc(). Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: convert HW flags to unsigned long bitmapJohannes Berg2015-06-101-1/+1
| | | | | | | | | | | | | | | As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: let flush() drop packets when possibleEmmanuel Grumbach2015-01-141-2/+2
| | | | | | | | | | | | | | | | When roaming / suspending, it makes no sense to wait until the transmit queues of the device are empty. In extreme condition they can be starved (VO saturating the air), but even in regular cases, it is pointless to delay the roaming because the low level driver is trying to send packets to an AP which is far away. We'd rather drop these packets and let TCP retransmit if needed. This will allow to speed up the roaming. For suspend, the explanation is even more trivial. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: introduce refcount for queue_stop_reasonsLuciano Coelho2014-06-231-2/+4
| | | | | | | | | | | | | Sometimes different vifs may be stopping the queues for the same reason (e.g. when several interfaces are performing a channel switch). Instead of using a bitmask for the reasons, use an integer that holds a refcount instead. In order to keep it backwards compatible, introduce a boolean in some functions that tell us whether the queue stopping should be refcounted or not. For now, use not refcounted for all calls to keep it functionally the same as before. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix on-channel remain-on-channelJohannes Berg2014-05-141-7/+20
| | | | | | | | | | | | | | | | | | | | | | | Jouni reported that if a remain-on-channel was active on the same channel as the current operating channel, then the ROC would start, but any frames transmitted using mgmt-tx on the same channel would get delayed until after the ROC. The reason for this is that the ROC starts, but doesn't have any handling for "remain on the same channel", so it stops the interface queues. The later mgmt-tx then puts the frame on the interface queues (since it's on the current operating channel) and thus they get delayed until after the ROC. To fix this, add some logic to handle remaining on the same channel specially and not stop the queues etc. in this case. This not only fixes the bug but also improves behaviour in this case as data frames etc. can continue to flow. Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Tested-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix software remain-on-channel implementationJohannes Berg2014-04-091-0/+1
| | | | | | | | | | | | | | | | | | | Jouni reported that when doing off-channel transmissions mixed with on-channel transmissions, the on-channel ones ended up on the off-channel in some cases. The reason for that is that during the refactoring of the off- channel code, I lost the part that stopped all activity and as a consequence the on-channel frames (including data frames) were no longer queued but would be transmitted on the temporary channel. Fix this by simply restoring the lost activity stop call. Cc: stable@vger.kernel.org Fixes: 2eb278e083549 ("mac80211: unify SW/offload remain-on-channel") Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Run deferred scan if last roc_list item is not startedJouni Malinen2013-09-301-0/+2
| | | | | | | | | | | | | | | | | mac80211 scan processing could get stuck if roc work for pending, but not started when a scan request was deferred due to such roc item. Normally the deferred scan would be started from ieee80211_start_next_roc(), but ieee80211_sw_roc_work() calls that only if the finished ROC was started. Fix this by calling ieee80211_run_deferred_scan() in the case the last ROC was not actually started. This issue was hit relatively easily in P2P find operations where Listen state (remain-on-channel) and Search state (scan) are repeated in a loop. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge branch 'for-john' of ↵John W. Linville2013-04-101-3/+3
|\ | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Conflicts: drivers/net/wireless/ath/carl9170/debug.c drivers/net/wireless/ath/carl9170/main.c net/mac80211/ieee80211_i.h
| * mac80211: purge remain-on-channel items when suspendingJohannes Berg2013-04-081-3/+3
| | | | | | | | | | | | | | | | | | | | They can't really be executed while suspended and could trigger work warnings, so abort all ROC items. When the system resumes the notifications about this will be delivered to userspace which can then act accordingly (though it will assume they were canceled/finished.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge branch 'master' of ↵John W. Linville2013-04-101-6/+17
|\ \ | |/ |/| | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/rt2x00/rt2x00pci.c
| * mac80211: fix remain-on-channel cancel crashJohannes Berg2013-03-251-6/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a ROC item is canceled just as it expires, the work struct may be scheduled while it is running (and waiting for the mutex). This results in it being run after being freed, which obviously crashes. To fix this don't free it when aborting is requested but instead mark it as "to be freed", which makes the work a no-op and allows freeing it outside. Cc: stable@vger.kernel.org [3.6+] Reported-by: Jouni Malinen <j@w1.fi> Tested-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: stop queues temporarily for flushingJohannes Berg2013-03-181-2/+2
| | | | | | | | | | | | | | | | | | | | Sometimes queues are flushed in the middle of operation, which can lead to driver issues. Stop queues temporarily, while flushing, to avoid transmitting new packets while they are being flushed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: pass queue bitmap to flush operationJohannes Berg2013-03-181-2/+2
| | | | | | | | | | | | | | | | | | | | There are a number of situations in which mac80211 only really needs to flush queues for one virtual interface, and in fact during this frames might be transmitted on other virtual interfaces. Calculate and pass a queue bitmap to the driver so it knows which queues to flush. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: Allow drivers to differentiate between ROC typesIlan Peer2013-03-061-1/+1
|/ | | | | | | | | | | Some devices can handle remain on channel requests differently based on the request type/priority. Add support to differentiate between different ROC types, i.e., indicate that the ROC is required for sending managment frames. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Add flushes before going off-channelSeth Forshee2013-02-111-0/+5
| | | | | | | | | | | | | | | | | | We've got a couple of races when enabling powersave with an AP for off-channel operation. The first is fairly simple. If we go off-channel before the nullfunc frame to enable PS is transmitted then it may not be received by the AP. Add a flush after enabling off-channel PS to prevent this from happening. The second race is a bit more subtle. If the driver supports QoS and has frames queued when the nullfunc frame is queued, those frames may get transmitted after the nullfunc frame. If PM is not set then the AP is being told that we've exited PS before we go off-channel and may try to deliver frames. To prevent this, add a flush after stopping the queues but before passing the nullfunc frame to the driver. Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Fix tx queue handling during scansSeth Forshee2013-02-111-20/+10
| | | | | | | | | | | | | | | | | | | | | | Scans currently work by stopping the netdev tx queues but leaving the mac80211 queues active. This stops the flow of incoming packets while still allowing mac80211 to transmit nullfunc and probe request frames to facilitate scanning. However, the driver may try to wake the mac80211 queues while in this state, which will also wake the netdev queues. To prevent this, add a new queue stop reason, IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx queues for off-channel operation. This prevents the netdev queues from waking when a driver wakes the mac80211 queues. This also stops all frames from being transmitted, even those meant to be sent off-channel. Add a new tx control flag, IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted when the queues are stopped only for the off-channel stop reason. Update all locations transmitting off-channel frames to use this flag. Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge branch 'master' of ↵John W. Linville2013-01-281-12/+7
|\ | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/ath/ath9k/main.c drivers/net/wireless/iwlwifi/dvm/tx.c
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 12:59:12 +0100