summaryrefslogtreecommitdiffstats
path: root/net/mac80211/tx.c (follow)
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch 'master' of ↵John W. Linville2013-04-241-105/+48
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
| * mac80211: improve the rate control APIFelix Fietkau2013-04-221-108/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow rate control modules to pass a rate selection table to mac80211 and the driver. This allows drivers to fetch the most recent rate selection from the sta pointer for already buffered frames. This allows rate control to respond faster to sudden link changes and it is also a step towards adding minstrel_ht support to drivers like iwlwifi. When a driver sets IEEE80211_HW_SUPPORTS_RC_TABLE, mac80211 will not fill info->control.rates with rates from the rate table (to preserve explicit overrides by the rate control module). The driver then explicitly calls ieee80211_get_tx_rates to merge overrides from info->control.rates with defaults from the sta rate table. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix CTS protection handlingFelix Fietkau2013-04-161-0/+8
| | | | | | | | | | | | | | | | | | The rates[0] CTS and RTS flags are only set after rate control has been called, so minstrel cannot use them to for setting the number of retries. This patch adds two new flags to explicitly indicate RTS/CTS use. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix and optimize MCS mask handlingFelix Fietkau2013-04-161-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | Currently the code always copies the configured MCS mask (even if it is set to default), but only uses it if legacy rates were also masked out. Fix this by adding a flag that tracks whether the configured MCS mask is set to default or not. Optimize the code further by storing a pointer to the configured rate mask in txrc instead of using memcpy. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix rate control tx handler for VHT ratesKarl Beldan2013-04-161-14/+17
| | | | | | | | | | | | | | | | | | Handle VHT rates like HT ones, otherwise we easily trigger the pre-HT rates WARN_ON(rc_rate->idx >= sband->n_bitrates) which will set rc_rate->idx to -1. Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: always pick a basic rate to tx RTS/CTS for pre-HT ratesKarl Beldan2013-04-111-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the 1st rate control entry is a pre-HT rate we want to set rts_cts_rate_idx "as the fastest basic rate that is not faster than the data rate"(code comments). But in case some bss allowed rate indexes are lower than the lowest bss basic rate, if the rate control selects a rate among the formers for its 1st rate control entry, rts_cts_rate_idx remains 0 and is not a basic rate index. This commit sets rts_cts_rate_idx to the lowest bss basic rate index in this situation. Note that the code assumes that lowest indexes == lowest bitrates. Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: Use a cfg80211_chan_def in ieee80211_hw_conf_chanKarl Beldan2013-03-251-2/+2
| | | | | | | | | | | | | | | | | | | | Drivers that don't use chanctxes cannot perform VHT association because they still use a "backward compatibility" pair of {ieee80211_channel, nl80211_channel_type} in ieee80211_conf and ieee80211_local. Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> [fix kernel-doc] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: ibss: use beacon_data struct for beacon and probe responseJohannes Berg2013-03-251-2/+5
| | | | | | | | | | | | | | | | Instead of having an SKB all the time, use a beacon_data struct with just the information required. This also allows removing a synchronize_rcu() and using kfree_rcu() instead. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge branch 'master' of ↵John W. Linville2013-04-101-2/+6
|\| | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/rt2x00/rt2x00pci.c net/mac80211/sta_info.c net/wireless/core.h
| * mac80211: stop queues temporarily for flushingJohannes Berg2013-03-181-0/+1
| | | | | | | | | | | | | | | | | | | | Sometimes queues are flushed in the middle of operation, which can lead to driver issues. Stop queues temporarily, while flushing, to avoid transmitting new packets while they are being flushed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: provide race-free 64-bit traffic countersJohannes Berg2013-03-071-2/+5
| | | | | | | | | | | | | | | | | | | | Make the TX bytes/packets counters race-free by keeping them per AC so concurrent TX on queues can't cause lost or wrong updates. This works since each station belongs to a single interface. While at it also make the bytes counters 64-bit. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * Merge remote-tracking branch 'mac80211/master' into HEADJohannes Berg2013-03-061-29/+51
| |\ | | | | | | | | | | | | | | | There are a few things that would otherwise conflict. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | | net: add ETH_P_802_3_MINSimon Horman2013-03-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for an 802.3 frame. Frames with a lower value in the ethernet type field are Ethernet II. Also update all the users of this value that David Miller and I could find to use the new constant. Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN should be >= not >. As suggested by Jesse Gross. Compile tested only. Cc: David Miller <davem@davemloft.net> Cc: Jesse Gross <jesse@nicira.com> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: John W. Linville <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Bart De Schuymer <bart.de.schuymer@pandora.be> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: linux-bluetooth@vger.kernel.org Cc: netfilter-devel@vger.kernel.org Cc: bridge@lists.linux-foundation.org Cc: linux-wireless@vger.kernel.org Cc: linux1394-devel@lists.sourceforge.net Cc: linux-media@vger.kernel.org Cc: netdev@vger.kernel.org Cc: dev@openvswitch.org Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge branch 'master' of ↵John W. Linville2013-03-061-1/+2
|\ \ \ | | |/ | |/| | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
| * | mac80211: fix oops on mesh PS broadcast forwardingMarco Porsch2013-03-011-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduced with de74a1d9032f4d37ea453ad2a647e1aff4cd2591 "mac80211: fix WPA with VLAN on AP side with ps-sta". Apparently overwrites the sdata pointer with non-valid data in the case of mesh. Fix this by checking for IFTYPE_AP_VLAN. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2013-03-061-28/+49
|\| | | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking fixes from David Miller: "A moderately sized pile of fixes, some specifically for merge window introduced regressions although others are for longer standing items and have been queued up for -stable. I'm kind of tired of all the RDS protocol bugs over the years, to be honest, it's way out of proportion to the number of people who actually use it. 1) Fix missing range initialization in netfilter IPSET, from Jozsef Kadlecsik. 2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes Berg. 3) Fix DMA syncing in SFC driver, from Ben Hutchings. 4) Fix regression in BOND device MAC address setting, from Jiri Pirko. 5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko. 6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips, fix from Dmitry Kravkov. 7) Missing cfgspace_lock initialization in BCMA driver. 8) Validate parameter size for SCTP assoc stats getsockopt(), from Guenter Roeck. 9) Fix SCTP association hangs, from Lee A Roberts. 10) Fix jumbo frame handling in r8169, from Francois Romieu. 11) Fix phy_device memory leak, from Petr Malat. 12) Omit trailing FCS from frames received in BGMAC driver, from Hauke Mehrtens. 13) Missing socket refcount release in L2TP, from Guillaume Nault. 14) sctp_endpoint_init should respect passed in gfp_t, rather than use GFP_KERNEL unconditionally. From Dan Carpenter. 15) Add AISX AX88179 USB driver, from Freddy Xin. 16) Remove MAINTAINERS entries for drivers deleted during the merge window, from Cesar Eduardo Barros. 17) RDS protocol can try to allocate huge amounts of memory, check that the user's request length makes sense, from Cong Wang. 18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own, bogus, definition. From Cong Wang. 19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll, from Frank Li. Also, fix a build error introduced in the merge window. 20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti. 21) Don't double count RTT measurements when we leave the TCP receive fast path, from Neal Cardwell." * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits) tcp: fix double-counted receiver RTT when leaving receiver fast path CAIF: fix sparse warning for caif_usb rds: simplify a warning message net: fec: fix build error in no MXC platform net: ipv6: Don't purge default router if accept_ra=2 net: fec: put tx to napi poll function to fix dead lock sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE rds: limit the size allocated by rds_message_alloc() MAINTAINERS: remove eexpress MAINTAINERS: remove drivers/net/wan/cycx* MAINTAINERS: remove 3c505 caif_dev: fix sparse warnings for caif_flow_cb ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver sctp: use the passed in gfp flags instead GFP_KERNEL ipv[4|6]: correct dropwatch false positive in local_deliver_finish l2tp: Restore socket refcount when sendmsg succeeds net/phy: micrel: Disable asymmetric pause for KSZ9021 bgmac: omit the fcs phy: Fix phy_device_free memory leak bnx2x: Fix KR2 work-around condition ...
| * mac80211: Ensure off-channel frames don't get queuedSeth Forshee2013-02-261-25/+31
| | | | | | | | | | | | | | | | | | | | | | Commit 6c17b77b67587b9f9e3070fb89fe98cef3187131 (mac80211: Fix tx queue handling during scans) contains a bug that causes off-channel frames to get queued when they should be handed down to the driver for transmit. Prevent this from happening. Reported-by: Fabio Rossi <rossi.f@inwind.it> Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix the problem of forwarding from DS to DS in MeshChun-Yeow Yeoh2013-02-261-1/+16
| | | | | | | | | | | | | | | | | | | | | | Unicast frame with unknown forwarding information always trigger the path discovery assuming destination is always located inside the MBSS. This patch allows the forwarding to look for mesh gate if path discovery inside the MBSS has failed. Reported-by: Cedric Voncken <cedric.voncken@acksys.fr> Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix tim_lock lockingJohannes Berg2013-02-261-2/+2
| | | | | | | | | | | | | | | | | | The ieee80211_beacon_add_tim() function might be called by drivers with BHs enabled, which causes a potential deadlock if TX happens at the same time and attempts to lock the tim_lock as well. Use spin_lock_bh to fix it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: convert to idr_alloc()Tejun Heo2013-02-281-14/+4
|/ | | | | | | | | Convert to the much saner new idr interface. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mac80211: clean up mesh codeJohannes Berg2013-02-151-15/+11
| | | | | | | | | | | There's various code with strange indentation, questionable loop and locking constructs, etc. The bigger change is moving the "sdata" argument to the first argument of all functions, like all other mac80211 functions that have one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: cache mesh beaconThomas Pedersen2013-02-151-53/+8
| | | | | | | | | | | | | | Previously, the entire mesh beacon would be generated each time the beacon timer fired. Instead generate a beacon head and tail (so the TIM can easily be inserted when mesh power save is on) when starting a mesh or the MBSS parameters change. Also add a mutex for protecting beacon updates and preventing leaks. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use spin_lock_bh() for tim_lockJohannes Berg2013-02-151-4/+2
| | | | | | | | | | | There's no need to use _irqsave() as the lock is never used in interrupt context. This also fixes a problem in the iwlwifi MVM driver that calls spin_unlock_bh() within its set_tim() callback. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix auth/assoc timeout handlingJohannes Berg2013-02-151-0/+2
| | | | | | | | | | | | | | | | | | | | | | | In my commit 1672c0e31917f49d31d30d79067103432bc20cc7 ("mac80211: start auth/assoc timeout on frame status") I broke auth/assoc timeout handling: in case we wait for the TX status, it now leaves the timeout field set to 0, which is a valid time and can compare as being before now ("jiffies"). Thus, if the work struct runs for some other reason, the auth/assoc is treated as having timed out. Fix this by introducing a separate "timeout_started" variable that tracks whether the timeout has started and is checked before timing out. Additionally, for proper TX status handling the change requires that the skb->dev pointer is set up for all the frames, so set it up for all frames in mac80211. Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix WPA with VLAN on AP side with ps-staMichael Braun2013-02-151-0/+1
| | | | | | | | | | | | | When sending a broadcast while at least on of the connected stations is sleeping, it gets queued and send after a DTIM beacon is sent. If the packet was to be sent on a vlan interface, the vif used for dequeing from the per-bss queue does not hold the per-vlan sdata. The correct sdata is required to use the correct per-vlan broadcast/multicast key. This patch fixes this by restoring the per-vlan sdata using the skb->dev entry. Signed-off-by: Michael Braun <michael-dev@fami-braun.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Fix tx queue handling during scansSeth Forshee2013-02-111-0/+15
| | | | | | | | | | | | | | | | | | | | | | Scans currently work by stopping the netdev tx queues but leaving the mac80211 queues active. This stops the flow of incoming packets while still allowing mac80211 to transmit nullfunc and probe request frames to facilitate scanning. However, the driver may try to wake the mac80211 queues while in this state, which will also wake the netdev queues. To prevent this, add a new queue stop reason, IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx queues for off-channel operation. This prevents the netdev queues from waking when a driver wakes the mac80211 queues. This also stops all frames from being transmitted, even those meant to be sent off-channel. Add a new tx control flag, IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted when the queues are stopped only for the off-channel stop reason. Update all locations transmitting off-channel frames to use this flag. Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: mesh power save basicsMarco Porsch2013-02-041-9/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: allow transmitting deauth with tainted keyJohannes Berg2013-02-041-1/+2
| | | | | | | | | | | | | | | When we had a connection for WoWLAN and after resume it needed to be disconnected, the previous commit enabled sending a deauth frame to the AP. This frame would not go through on MFP-enabled networks as the key for it is marked tainted before the frame is transmitted. Allow a tainted key to be used for deauth frames. Worst case, we'll use a wrong key because the PTK was rekeyed while suspended, but more likely the PTK is still fine and the taint flag really only applies to the GTK(s). Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge remote-tracking branch 'wireless-next/master' into HEADJohannes Berg2013-01-291-3/+6
|\
| * Merge branch 'master' of ↵John W. Linville2013-01-281-3/+6
| |\ | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/ath/ath9k/main.c drivers/net/wireless/iwlwifi/dvm/tx.c
| | * mac80211: fix monitor mode injectionFelix Fietkau2013-01-161-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | Channel contexts are not always used with monitor interfaces. If no channel context is set, use the oper channel, otherwise tx fails. Signed-off-by: Felix Fietkau <nbd@openwrt.org> [check local->use_chanctx] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | | mac80211: avoid a build warningArnd Bergmann2013-01-251-4/+4
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gcc cannot prove that the value of sdata->vif.type does not change between the switch() statement and the second comparison to NL80211_IFTYPE_AP, causing a harmless warning. Slightly reordering the code makes the warning go away with no functional change. Without this patch, building ARM at91sam9g45_defconfig with gcc-4.6 results in: net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit': net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* / mac80211: move add_tim to subfunctionMarco Porsch2013-01-161-19/+28
|/ | | | | | | | This functions will be used for mesh beacons, too. Signed-off-by: Marco Porsch <marco@cozybit.com> [some formatting fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge branch 'for-john' of ↵John W. Linville2012-12-061-7/+2
|\ | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Conflicts: drivers/net/wireless/mwifiex/sta_ioctl.c net/mac80211/scan.c
| * mac80211: remove probe response temporary buffer allocationJohannes Berg2012-11-301-7/+2
| | | | | | | | | | | | | | Instead of allocating a temporary buffer to build IEs build them right into the SKB. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge branch 'for-john' of ↵John W. Linville2012-11-261-10/+10
|\| | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
| * mac80211: convert to channel definition structJohannes Berg2012-11-261-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert mac80211 (and where necessary, some drivers a little bit) to the new channel definition struct. This will allow extending mac80211 for VHT, which is currently restricted to channel contexts since there are no drivers using that which makes it easier. As I also don't care about VHT for drivers not using the channel context API, I won't convert the previous API to VHT support. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge branch 'master' of ↵John W. Linville2012-11-211-3/+6
|\ \ | |/ |/| | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c drivers/net/wireless/iwlwifi/pcie/tx.c
| * mac80211: call skb_dequeue/ieee80211_free_txskb instead of __skb_queue_purgeFelix Fietkau2012-11-101-3/+6
| | | | | | | | | | | | | | | | Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: fix TX error pathJohannes Berg2012-11-071-0/+1
| | | | | | | | | | | | | | | | | | | | One error path in ieee80211_subif_start_xmit() will double-free the SKB. Set it to NULL to prevent that. This issue was introduced by my channel context changes. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: make client powersave independent of interface typeMarco Porsch2012-10-191-42/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch prepares mac80211 for a later implementation of mesh or ad-hoc powersave clients. The structures related to powersave (buffer, TIM map, counters) are moved from the AP-specific interface structure to a generic structure that can be embedded into any interface type. The functions related to powersave are prepared to allow easy extension with different interface types. For example with: + } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) { + ps = &sdata->u.mesh.ps; Some references to the AP's beacon structure are removed where they were obviously not used. The patch compiles without warning and has been briefly tested as AP interface with one client in PS mode. Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: remove some unused codeJohannes Berg2012-10-181-2/+0
| | | | | | | | | | | | | | | | | | | | There are a number of unused variables that gcc pointed out (when building with W=1) as well as some conditions that can never be true due to the datatypes used: unsigned values can't be less than zero. Remove this code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: use channel contextsJohannes Berg2012-10-171-68/+115
|/ | | | | | | | | | | | | | | | | | | | | | | | | Instead of operating on a single channel only, use the new channel context infrastructure in all mac80211 code. This enables drivers that want to use the new channel context infrastructure to use multiple channels, while nothing should change for all the other drivers that don't support it. Right now this disables both TX power settings and spatial multiplexing powersave. Both need to be re-enabled on a channel context basis. Additionally, when channel contexts are used drop the connection when channel switch is received rather than trying to handle it. This will have to be improved later. [With fixes from Eliad and Emmanuel incorporated] Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use ieee80211_free_txskb to fix possible skb leaksFelix Fietkau2012-10-081-10/+12
| | | | | | | | | | A few places free skbs using dev_kfree_skb even though they're called after ieee80211_subif_start_xmit might have cloned it for tracking tx status. Use ieee80211_free_txskb here to prevent skb leaks. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: add key flag for management keysJohannes Berg2012-09-101-1/+1
| | | | | | | | | | | | Mark keys that might be used to receive management frames so drivers can fall back on software crypto for them if they don't support hardware offload. As the new flag is only set correctly for RX keys and the existing IEEE80211_KEY_FLAG_SW_MGMT flag can only affect TX, also rename the latter to IEEE80211_KEY_FLAG_SW_MGMT_TX. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge remote-tracking branch 'mac80211/master' into mac80211-nextJohannes Berg2012-09-061-22/+16
|\ | | | | | | | | | | | | | | | | | | Pull in mac80211.git to let the next patch apply without conflicts, also resolving a hwsim conflict. Conflicts: drivers/net/wireless/mac80211_hwsim.c Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix DS to MBSS address translationThomas Pedersen2012-08-221-22/+16
| | | | | | | | | | | | | | | | | | | | | | | | The destination address of unicast frames forwarded through a mesh gate was being replaced with the broadcast address. Instead leave the original destination address as the mesh DA. If the nexthop address is not in the mpath table it will be resolved. If that fails, the frame will be forwarded to known mesh gates. Reported-by: Cedric Voncken <cedric.voncken@acksys.fr> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: clean up ieee80211_subif_start_xmitJohannes Berg2012-08-201-17/+6
| | | | | | | | | | | | | | There's no need to carry around a return value that is always NETDEV_TX_OK anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: remove almost unused local variableJohannes Berg2012-08-201-5/+2
| | | | | | | | | | | | | | In ieee80211_beacon_get_tim() we can use the txrc.sband instead of a separate local variable. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: avoid using synchronize_rcu in ieee80211_set_probe_respEyal Shapira2012-08-201-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This could take a while (100ms+) and may delay sending assoc resp in AP mode with WPS or P2P GO (as setting the probe resp takes place there). We've encountered situations where the delay was big enough to cause connection problems with devices like Galaxy Nexus. Switch to using call_rcu with a free handler. [Arik - rework to use plain buffer and instead of skb] Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-02 22:05:27 +0100