summaryrefslogtreecommitdiffstats
path: root/net/mac80211 (follow)
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: fix deadlock in driver-managed RX BA session startJohannes Berg2017-09-063-14/+28
| | | | | | | | | | | | | | | | When an RX BA session is started by the driver, and it has to tell mac80211 about it, the corresponding bit in tid_rx_manage_offl gets set and the BA session work is scheduled. Upon testing this bit, it will call __ieee80211_start_rx_ba_session(), thus deadlocking as it already holds the ampdu_mlme.mtx, which that acquires again. Fix this by adding ___ieee80211_start_rx_ba_session(), a version of the function that requires the mutex already held. Cc: stable@vger.kernel.org Fixes: 699cb58c8a52 ("mac80211: manage RX BA session offload without SKB queue") Reported-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Complete ampdu work schedule during session tear downIlan peer2017-09-061-0/+18
| | | | | | | | | | | | | | | | | | Commit 7a7c0a6438b8 ("mac80211: fix TX aggregation start/stop callback race") added a cancellation of the ampdu work after the loop that stopped the Tx and Rx BA sessions. However, in some cases, e.g., during HW reconfig, the low level driver might call mac80211 APIs to complete the stopping of the BA sessions, which would queue the ampdu work to handle the actual completion. This work needs to be performed as otherwise mac80211 data structures would not be properly synced. Fix this by checking if BA session STOP_CB bit is set after the BA session cancellation and properly clean the session. Signed-off-by: Ilan Peer <ilan.peer@intel.com> [Johannes: the work isn't flushed because that could do other things we don't want, and the locking situation isn't clear] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: flush hw_roc_start work before cancelling the ROCAvraham Stern2017-09-051-0/+2
| | | | | | | | | | | | | | | | | | | | | | | When HW ROC is supported it is possible that after the HW notified that the ROC has started, the ROC was cancelled and another ROC was added while the hw_roc_start worker is waiting on the mutex (since cancelling the ROC and adding another one also holds the same mutex). As a result, the hw_roc_start worker will continue to run after the new ROC is added but before it is actually started by the HW. This may result in notifying userspace that the ROC has started before it actually does, or in case of management tx ROC, in an attempt to tx while not on the right channel. In addition, when the driver will notify mac80211 that the second ROC has started, mac80211 will warn that this ROC has already been notified. Fix this by flushing the hw_roc_start work before cancelling an ROC. Cc: stable@vger.kernel.org Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: agg-tx: call drv_wake_tx_queue in proper contextJohannes Berg2017-09-051-0/+4
| | | | | | | | | | | | | | | Since drv_wake_tx_queue() is normally called in the TX path, which is already in an RCU critical section, we should call it the same way in the aggregation code path, so if the driver expects to be able to use RCU, it'll already be protected without having to enter a nested critical section. Additionally, disable soft-IRQs, since not doing so could cause issues in a driver that relies on them already being disabled like in the other path. Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Fix null pointer dereference with iTXQ supportChunho Lee2017-09-051-1/+2
| | | | | | | | | | | | This change adds null pointer check before dereferencing pointer dev on netif_tx_start_all_queues() when an interface is added. With iTXQ support, netif_tx_start_all_queues() is always called while an interface is added. however, the netdev queues are not associated and dev is null when the interface is either NL80211_IFTYPE_P2P_DEVICE or NL80211_IFTYPE_NAN. Signed-off-by: Chunho Lee <ch.lee@newracom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add MESH IE in the correct orderLiad Kaufman2017-09-051-1/+1
| | | | | | | | | VHT MESH support was added, but the order of the IEs wasn't enforced. Fix that. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: shorten debug prints using ht_dbg() to avoid warningSharon Dvir2017-09-051-2/+2
| | | | | | | | | Invoking ht_dbg() with too long of a string will print a warning. Shorten the messages while retaining the printed patameters. Signed-off-by: Sharon Dvir <sharon.dvir@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix VLAN handling with TXQsJohannes Berg2017-09-052-9/+44
| | | | | | | | | | | | | | | | | | | | | | With TXQs, the AP_VLAN interfaces are resolved to their owner AP interface when enqueuing the frame, which makes sense since the frame really goes out on that as far as the driver is concerned. However, this introduces a problem: frames to be encrypted with a VLAN-specific GTK will now be encrypted with the AP GTK, since the information about which virtual interface to use to select the key is taken from the TXQ. Fix this by preserving info->control.vif and using that in the dequeue function. This now requires doing the driver-mapping in the dequeue as well. Since there's no way to filter the frames that are sitting on a TXQ, drop all frames, which may affect other interfaces, when an AP_VLAN is removed. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix incorrect assignment of reassoc valueSimon Dinkin2017-09-051-1/+1
| | | | | | | | | | | this fix minor issue in the log message. in ieee80211_rx_mgmt_assoc_resp function, when assigning the reassoc value from the mgmt frame control: ieee80211_is_reassoc_resp function need to be used, instead of ieee80211_is_reassoc_req function. Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add api to start ba session timer expired flowNaftali Goldstein2017-08-091-1/+21
| | | | | | | | | | | Some drivers handle rx buffer reordering internally (and by extension handle also the rx ba session timer internally), but do not ofload the addba/delba negotiation. Add an api for these drivers to properly tear-down the ba session, including sending a delba. Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* net: manual clean code which call skb_put_[data:zero]yuan linyu2017-06-202-18/+13
| | | | | Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
* networking: make skb_push & __skb_push return void pointersJohannes Berg2017-06-163-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* networking: make skb_put & friends return void pointersJohannes Berg2017-06-168-15/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions (skb_put, __skb_put and pskb_put) return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_put, __skb_put }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_put, __skb_put }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) which actually doesn't cover pskb_put since there are only three users overall. A handful of stragglers were converted manually, notably a macro in drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many instances in net/bluetooth/hci_sock.c. In the former file, I also had to fix one whitespace problem spatch introduced. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* networking: introduce and use skb_put_data()Johannes Berg2017-06-168-53/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* networking: convert many more places to skb_put_zero()Johannes Berg2017-06-1614-44/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There were many places that my previous spatch didn't find, as pointed out by yuan linyu in various patches. The following spatch found many more and also removes the now unnecessary casts: @@ identifier p, p2; expression len; expression skb; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_zero(skb, len); | -p = (t)skb_put(skb, len); +p = skb_put_zero(skb, len); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, len); | -memset(p, 0, len); ) @@ type t, t2; identifier p, p2; expression skb; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, sizeof(*p)); | -memset(p, 0, sizeof(*p)); ) @@ expression skb, len; @@ -memset(skb_put(skb, len), 0, len); +skb_put_zero(skb, len); Apply it to the tree (with one manual fixup to keep the comment in vxlan.c, which spatch removed.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-06-156-40/+48
|\ | | | | | | | | | | | | The conflicts were two cases of overlapping changes in batman-adv and the qed driver. Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge tag 'mac80211-for-davem-2017-06-13' of ↵David S. Miller2017-06-135-37/+44
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Some fixes: * Avi fixes some fallout from my mac80211 RX flags changes * Emmanuel fixes an issue with adhering to the spec, and an oversight in the SMPS management code * Jason's patch makes mac80211 use constant-time memory comparisons for message authentication, to avoid having potentially observable timing differences * my fix makes mac80211 set the basic rates bitmap before the channel so the next update to the driver has more consistent data - this required another rework patch to remove some useless 5/10 MHz code that can never be hit ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| | * mac80211: don't send SMPS action frame in AP mode when not neededEmmanuel Grumbach2017-06-131-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mac80211 allows to modify the SMPS state of an AP both, when it is started, and after it has been started. Such a change will trigger an action frame to all the peers that are currently connected, and will be remembered so that new peers will get notified as soon as they connect (since the SMPS setting in the beacon may not be the right one). This means that we need to remember the SMPS state currently requested as well as the SMPS state that was configured initially (and advertised in the beacon). The former is bss->req_smps and the latter is sdata->smps_mode. Initially, the AP interface could only be started with SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF always. Later, a nl80211 API was added to be able to start an AP with a different AP mode. That code forgot to update bss->req_smps and because of that, if the AP interface was started with SMPS_DYNAMIC, we had: sdata->smps_mode = SMPS_DYNAMIC bss->req_smps = SMPS_OFF That configuration made mac80211 think it needs to fire off an action frame to any new station connecting to the AP in order to let it know that the actual SMPS configuration is SMPS_OFF. Fix that by properly setting bss->req_smps in ieee80211_start_ap. Fixes: f69931748730 ("mac80211: set smps_mode according to ap params") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * mac80211/wpa: use constant time memory comparison for MACsJason A. Donenfeld2017-06-131-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Otherwise, we enable all sorts of forgeries via timing attack. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * mac80211: set bss_info data before configuring the channelJohannes Berg2017-06-131-10/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When mac80211 changes the channel, it also calls into the driver's bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver may, like iwlwifi does, access more data from bss_info in that case and iwlwifi accesses the basic_rates bitmap, but if changing from a band with more (basic) rates to one with fewer, an out-of-bounds access of the rate array may result. While we can't avoid having invalid data at some point in time, we can avoid having it while we call the driver - so set up all the data before configuring the channel, and then apply it afterwards. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677 Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * mac80211: remove 5/10 MHz rate code from station MLMEJohannes Berg2017-06-131-21/+3
| | | | | | | | | | | | | | | | | | | | | | | | There's no need for the station MLME code to handle bitrates for 5 or 10 MHz channels when it can't ever create such a configuration. Remove the unnecessary code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * mac80211: Fix incorrect condition when checking rx timestampAvraham Stern2017-06-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the driver reports the rx timestamp at PLCP start, mac80211 can only handle legacy encoding, but the code checks that the encoding is not legacy. Fix this. Fixes: da6a4352e7c8 ("mac80211: separate encoding/bandwidth from flags") Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| | * mac80211: don't look at the PM bit of BAR framesEmmanuel Grumbach2017-06-131-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a peer sends a BAR frame with PM bit clear, we should not modify its PM state as madated by the spec in 802.11-20012 10.2.1.2. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * | mac80211: free netdev on dev_alloc_name() errorJohannes Berg2017-06-091-0/+1
| |/ | | | | | | | | | | | | | | | | | | | | The change to remove free_netdev() from ieee80211_if_free() erroneously didn't add the necessary free_netdev() for when ieee80211_if_free() is called directly in one place, rather than as the priv_destructor. Add the missing call. Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: Fix inconsistent teardown and release of private netdev state.David S. Miller2017-06-071-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Network devices can allocate reasources and private memory using netdev_ops->ndo_init(). However, the release of these resources can occur in one of two different places. Either netdev_ops->ndo_uninit() or netdev->destructor(). The decision of which operation frees the resources depends upon whether it is necessary for all netdev refs to be released before it is safe to perform the freeing. netdev_ops->ndo_uninit() presumably can occur right after the NETDEV_UNREGISTER notifier completes and the unicast and multicast address lists are flushed. netdev->destructor(), on the other hand, does not run until the netdev references all go away. Further complicating the situation is that netdev->destructor() almost universally does also a free_netdev(). This creates a problem for the logic in register_netdevice(). Because all callers of register_netdevice() manage the freeing of the netdev, and invoke free_netdev(dev) if register_netdevice() fails. If netdev_ops->ndo_init() succeeds, but something else fails inside of register_netdevice(), it does call ndo_ops->ndo_uninit(). But it is not able to invoke netdev->destructor(). This is because netdev->destructor() will do a free_netdev() and then the caller of register_netdevice() will do the same. However, this means that the resources that would normally be released by netdev->destructor() will not be. Over the years drivers have added local hacks to deal with this, by invoking their destructor parts by hand when register_netdevice() fails. Many drivers do not try to deal with this, and instead we have leaks. Let's close this hole by formalizing the distinction between what private things need to be freed up by netdev->destructor() and whether the driver needs unregister_netdevice() to perform the free_netdev(). netdev->priv_destructor() performs all actions to free up the private resources that used to be freed by netdev->destructor(), except for free_netdev(). netdev->needs_free_netdev is a boolean that indicates whether free_netdev() should be done at the end of unregister_netdevice(). Now, register_netdevice() can sanely release all resources after ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit() and netdev->priv_destructor(). And at the end of unregister_netdevice(), we invoke netdev->priv_destructor() and optionally call free_netdev(). Signed-off-by: David S. Miller <davem@davemloft.net>
* | mac80211: add the action to the drv_ampdu_action tracepointEmmanuel Grumbach2017-06-131-4/+7
| | | | | | | | | | | | | | | | | | It is very useful to know what ampdu action is currently happening. Add this information to the tracepoint. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: manage RX BA session offload without SKB queueJohannes Berg2017-06-086-73/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | Instead of using the SKB queue with the fake pkt_type for the offloaded RX BA session management, also handle this with the normal aggregation state machine worker. This also makes the use of this more reliable since it gets rid of the allocation of the fake skb. Combined with the previous patch, this finally allows us to get rid of the pkt_type hack entirely, so do that as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge remote-tracking branch 'net-next/master' into mac80211-nextJohannes Berg2017-06-087-102/+74
|\| | | | | | | | | | | | | This brings in commit 7a7c0a6438b8 ("mac80211: fix TX aggregation start/stop callback race") to allow the follow-up cleanup. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix dropped counter in multiqueue RXJohannes Berg2017-06-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | In the commit enabling per-CPU station statistics, I inadvertedly copy-pasted some code to update rx_packets and forgot to change it to update rx_dropped_misc. Fix that. This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953. Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU") Reported-by: Petru-Florin Mihancea <petrum@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: fix TX aggregation start/stop callback raceJohannes Berg2017-05-305-100/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When starting or stopping an aggregation session, one of the steps is that the driver calls back to mac80211 that the start/stop can proceed. This is handled by queueing up a fake SKB and processing it from the normal iface/sdata work. Since this isn't flushed when disassociating, the following race is possible: * associate * start aggregation session * driver callback * disassociate * associate again to the same AP * callback processing runs, leading to a WARN_ON() that the TID hadn't requested aggregation If the second association isn't to the same AP, there would only be a message printed ("Could not find station: <addr>"), but the same race could happen. Fix this by not going the whole detour with a fake SKB etc. but simply looking up the aggregation session in the driver callback, marking it with a START_CB/STOP_CB bit and then scheduling the regular aggregation work that will now process these bits as well. This also simplifies the code and gets rid of the whole problem with allocation failures of said skb, which could have left the session in limbo. Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: strictly check mesh address extension modeRajkumar Manoharan2017-05-171-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Mesh forwarding path checks for address extension mode to fetch appropriate proxied address and MPP address. Existing condition that looks for 6 address format is not strict enough so that frames with improper values are processed and invalid entries are added into MPP table. Fix that by adding a stricter check before processing the packet. Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension mode 0x3 as reserved one. And also Table Table 9-13 does not specify 0x3 as valid address field. Fixes: 9b395bc3be1c ("mac80211: verify that skb data is present") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: Invoke TX LED in more code pathsBjorn Andersson2017-05-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ieee80211_tx_status() is only one of the possible ways a driver can report a handled packet, some drivers call this for every packet while others calls it rarely or never. In order to invoke the TX LED in the non-status reporting cases this patch pushes the call to ieee80211_led_tx() into ieee80211_report_used_skb(), which is shared between the various code paths. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | skbuff/mac80211: introduce and use skb_put_zero()Johannes Berg2017-05-302-8/+4
| | | | | | | | | | | | | | | | | | | | | | | | This pattern was introduced a number of times in mac80211 just now, and since it's present in a number of other places it makes sense to add a little helper for it. This just adds the helper and transforms the mac80211 code, a later patch will transform other places. Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: enable VHT for mesh channel processingSimon Wunderlich2017-05-241-1/+3
| | | | | | | | | | Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: mesh: support sending wide bandwidth CSASimon Wunderlich2017-05-243-2/+82
| | | | | | | | | | | | | | | | | | To support HT and VHT CSA, beacons and action frames must include the corresponding IEs. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> [make ieee80211_ie_build_wide_bw_cs() return void] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: mark as action frame when parsing IEs of CSA action framesSimon Wunderlich2017-05-191-1/+1
| | | | | | | | | | Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: mesh: Allow following CSA to DFS channels if userspace handles itBenjamin Berg2017-05-193-3/+15
| | | | | | | | | | | | | | | | | | | | If userspace has flagged support for DFS earlier, then we can follow CSA to DFS channels. So instead of rejecting the switch, allow it to happen if the flag has been set during mesh setup. Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: move clearing result into ieee80211_parse_ch_switch_ie()Johannes Berg2017-05-194-3/+2
| | | | | | | | | | | | | | Clear the csa_ie in ieee80211_parse_ch_switch_ie() where the data is filled in, rather than in each caller. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: mesh: mark channel as unusable if a regulatory MESH CSA is receivedBenjamin Berg2017-05-193-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In the Mesh Channel Switch Parameters (8.4.2.105) the reason is specified to WLAN_REASON_MESH_CHAN_REGULATORY in the case that a regulatory limitation was the cause for the switch. This means another station detected a radar event. Mark the channel as unusable if this happens. Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> [sw: style cleanup, rebase] Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: Dynamically set CoDel parameters per stationToke Høiland-Jørgensen2017-05-175-2/+57
|/ | | | | | | | | | | | | | | | | | | | | | CoDel can be too aggressive if a station sends at a very low rate, leading reduced throughput. This gets worse the more stations are present, as each station gets more bursty the longer the round-robin scheduling between stations takes. This adds dynamic adjustment of CoDel parameters per station. It uses the rate selection information to estimate throughput and sets more lenient CoDel parameters if the estimated throughput is below a threshold (modified by the number of active stations). A new callback is added that drivers can use to notify mac80211 about changes in expected throughput, so the same adjustment can be made for cards that implement rate control in firmware. Drivers that don't use this will just get the default parameters. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> [remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove inline annotation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix IBSS presp allocation sizeJohannes Berg2017-05-081-0/+2
| | | | | | | | | | | When VHT IBSS support was added, the size of the extra elements wasn't considered in ieee80211_ibss_build_presp(), which makes it possible that it would overrun the allocated buffer. Fix it by allocating the necessary space. Fixes: abcff6ef01f9 ("mac80211: add VHT support for IBSS") Reported-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: bail out from prep_connection() if a reconfig is ongoingLuca Coelho2017-05-081-0/+4
| | | | | | | | | | | | | If ieee80211_hw_restart() is called during authentication, the authentication process will continue, causing the driver to be called in a wrong state. This ultimately causes an oops in the iwlwifi driver (at least). This fixes bugzilla 195299 partly. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195299 Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: add request id to cfg80211_sched_scan_*() apiArend Van Spriel2017-04-283-4/+4
| | | | | | | | | | | | Have proper request id filled in the SCHED_SCAN_RESULTS and SCHED_SCAN_STOPPED notifications toward user-space by having the driver provide it through the api. Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Add support for BSS max idle period elementAvraham Stern2017-04-283-1/+23
| | | | | | | | | | | | | | Parse the BSS max idle period element and set the BSS configuration accordingly so the driver can use this information to configure the max idle period and to use protected management frames for keep alive when required. The BSS max idle period element is defined in IEEE802.11-2016, section 9.4.2.79 Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Fix possible sband related NULL pointer de-referenceMohammed Shafi Shajakhan2017-04-2811-70/+139
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even if the channel context configuration is NULL. This crashes for chipsets which support 5 Ghz alone when it tries to access members of 'sband'. Channel context configuration can be NULL in multivif case and when channel switch is in progress (or) when it fails. Fix this by replacing the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which returns a NULL pointer for sband when the channel configuration is NULL. An example scenario is as below: In multivif mode (AP + STA) with drivers like ath10k, when we do a channel switch in the AP vif (which has a number of clients connected) and a STA vif which is connected to some other AP, when the channel switch in AP vif fails, while the STA vifs tries to connect to the other AP, there is a window where the channel context is NULL/invalid and this results in a crash while the clients connected to the AP vif tries to reconnect and this race is very similar to the one investigated by Michal in https://patchwork.kernel.org/patch/3788161/ and this does happens with hardware that supports 5Ghz alone after long hours of testing with continuous channel switch on the AP vif ieee80211 phy0: channel context reservation cannot be finalized because some interfaces aren't switching wlan0: failed to finalize CSA, disconnecting wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice (Reason: 3=DEAUTH_LEAVING) WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211] [<bf77272c>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211])) [<bf73cc50>] (nl80211_new_station [cfg80211]) Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = d5f4c000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM PC is at sta_info_alloc+0x380/0x3fc [mac80211] LR is at sta_info_alloc+0x37c/0x3fc [mac80211] [<bf772738>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211]) [<bf73cc50>] (nl80211_new_station [cfg80211])) Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add ieee80211_tx_status_extFelix Fietkau2017-04-281-28/+46
| | | | | | | | | | | | | | | | This allows the driver to pass in struct ieee80211_tx_status directly. Make ieee80211_tx_status_noskb a wrapper around it. As with ieee80211_tx_status_noskb, there is no _ni variant of this call, because it probably won't be needed. Even if the driver won't provide any extra status info other than what's in struct ieee80211_tx_info already, it can optimize status reporting this way by passing in the station pointer. Signed-off-by: Felix Fietkau <nbd@nbd.name> [use C99 initializers] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: move ieee80211_tx_status_noskb below ieee80211_tx_statusFelix Fietkau2017-04-281-58/+58
| | | | | | | Makes further cleanups more readable Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: make rate control tx status API more extensibleFelix Fietkau2017-04-285-51/+42
| | | | | | | | | | | Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack struct ieee80211_tx_status instead of struct ieee80211_tx_info. This struct can be used to pass extra information, e.g. for dynamic tx power control Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use bitfield macros for encoded rateJohannes Berg2017-04-282-30/+50
| | | | | | | Instead of hand-coding the bit manipulations, use the bitfield macros to generate the code for the encoded bitrate. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: rename ieee80211_rx_status::vht_nss to just nssJohannes Berg2017-04-283-7/+7
| | | | | | | | | | | | | | | | | | | This field will need to be used again for HE, so rename it now. Again, mostly done with this spatch: @@ expression status; @@ -status->vht_nss +status->nss @@ expression status; @@ -status.vht_nss +status.nss Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-01 13:37:23 +0100