| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- gro: initialize network_offset in network layer
- tcp: reduce accepted window in NEW_SYN_RECV state
Current release - new code bugs:
- eth: mlx5e: do not use ptp structure for tx ts stats when not
initialized
- eth: ice: check for unregistering correct number of devlink params
Previous releases - regressions:
- bpf: Allow delete from sockmap/sockhash only if update is allowed
- sched: taprio: extend minimum interval restriction to entire cycle
too
- netfilter: ipset: add list flush to cancel_gc
- ipv4: fix address dump when IPv4 is disabled on an interface
- sock_map: avoid race between sock_map_close and sk_psock_put
- eth: mlx5: use mlx5_ipsec_rx_status_destroy to correctly delete
status rules
Previous releases - always broken:
- core: fix __dst_negative_advice() race
- bpf:
- fix multi-uprobe PID filtering logic
- fix pkt_type override upon netkit pass verdict
- netfilter: tproxy: bail out if IP has been disabled on the device
- af_unix: annotate data-race around unix_sk(sk)->addr
- eth: mlx5e: fix UDP GSO for encapsulated packets
- eth: idpf: don't enable NAPI and interrupts prior to allocating Rx
buffers
- eth: i40e: fully suspend and resume IO operations in EEH case
- eth: octeontx2-pf: free send queue buffers incase of leaf to inner
- eth: ipvlan: dont Use skb->sk in ipvlan_process_v{4,6}_outbound"
* tag 'net-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
netdev: add qstat for csum complete
ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
net: ena: Fix redundant device NUMA node override
ice: check for unregistering correct number of devlink params
ice: fix 200G PHY types to link speed mapping
i40e: Fully suspend and resume IO operations in EEH case
i40e: factoring out i40e_suspend/i40e_resume
e1000e: move force SMBUS near the end of enable_ulp function
net: dsa: microchip: fix RGMII error in KSZ DSA driver
ipv4: correctly iterate over the target netns in inet_dump_ifaddr()
net: fix __dst_negative_advice() race
nfc/nci: Add the inconsistency check between the input data length and count
MAINTAINERS: dwmac: starfive: update Maintainer
net/sched: taprio: extend minimum interval restriction to entire cycle too
net/sched: taprio: make q->picos_per_byte available to fill_sched_entry()
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
net: ti: icssg-prueth: Fix start counter for ft1 filter
sock_map: avoid race between sock_map_close and sk_psock_put
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 syzbot reports that nf_reinject() could be called without
rcu_read_lock() when flushing pending packets at nfnetlink
queue removal, from Eric Dumazet.
Patch #2 flushes ipset list:set when canceling garbage collection to
reference to other lists to fix a race, from Jozsef Kadlecsik.
Patch #3 restores q-in-q matching with nft_payload by reverting
f6ae9f120dad ("netfilter: nft_payload: add C-VLAN support").
Patch #4 fixes vlan mangling in skbuff when vlan offload is present
in skbuff, without this patch nft_payload corrupts packets
in this case.
Patch #5 fixes possible nul-deref in tproxy no IP address is found in
netdevice, reported by syzbot and patch from Florian Westphal.
Patch #6 removes a superfluous restriction which prevents loose fib
lookups from input and forward hooks, from Eric Garver.
My assessment is that patches #1, #2 and #5 address possible kernel
crash, anything else in this batch fixes broken features.
netfilter pull request 24-05-29
* tag 'nf-24-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
netfilter: nft_payload: restore vlan q-in-q match support
netfilter: ipset: Add list flush to cancel_gc
netfilter: nfnetlink_queue: acquire rcu_read_lock() in instance_destroy_rcu()
====================
Link: https://lore.kernel.org/r/20240528225519.1155786-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This removes the restriction of needing iif selector in the
forward/input hooks for fib lookups when requested result is
oif/oifname.
Removing this restriction allows "loose" lookups from the forward hooks.
Fixes: be8be04e5ddb ("netfilter: nft_fib: reverse path filter for policy-based routing on iif")
Signed-off-by: Eric Garver <eric@garver.life>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
syzbot reports:
general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
[..]
RIP: 0010:nf_tproxy_laddr4+0xb7/0x340 net/ipv4/netfilter/nf_tproxy_ipv4.c:62
Call Trace:
nft_tproxy_eval_v4 net/netfilter/nft_tproxy.c:56 [inline]
nft_tproxy_eval+0xa9a/0x1a00 net/netfilter/nft_tproxy.c:168
__in_dev_get_rcu() can return NULL, so check for this.
Reported-and-tested-by: syzbot+b94a6818504ea90d7661@syzkaller.appspotmail.com
Fixes: cc6eb4338569 ("tproxy: use the interface primary IP address as a default value for --on-ip")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Userspace assumes vlan header is present at a given offset, but vlan
offload allows to store this in metadata fields of the skbuff. Hence
mangling vlan results in a garbled packet. Handle this transparently by
adding a parser to the kernel.
If vlan metadata is present and payload offset is over 12 bytes (source
and destination mac address fields), then subtract vlan header present
in vlan metadata, otherwise mangle vlan metadata based on offset and
length, extracting data from the source register.
This is similar to:
8cfd23e67401 ("netfilter: nft_payload: work around vlan header stripping")
to deal with vlan payload mangling.
Fixes: 7ec3f7b47b8d ("netfilter: nft_payload: add packet mangling support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Revert f6ae9f120dad ("netfilter: nft_payload: add C-VLAN support").
f41f72d09ee1 ("netfilter: nft_payload: simplify vlan header handling")
already allows to match on inner vlan tags by subtract the vlan header
size to the payload offset which has been popped and stored in skbuff
metadata fields.
Fixes: f6ae9f120dad ("netfilter: nft_payload: add C-VLAN support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Flushing list in cancel_gc drops references to other lists right away,
without waiting for RCU to destroy list. Fixes race when referenced
ipsets can't be destroyed while referring list is scheduled for destroy.
Fixes: 97f7cf1cd80e ("netfilter: ipset: fix performance regression in swap operation")
Signed-off-by: Alexander Maltsev <keltar.gw@gmail.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
syzbot reported that nf_reinject() could be called without rcu_read_lock() :
WARNING: suspicious RCU usage
6.9.0-rc7-syzkaller-02060-g5c1672705a1a #0 Not tainted
net/netfilter/nfnetlink_queue.c:263 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by syz-executor.4/13427:
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:329 [inline]
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_do_batch kernel/rcu/tree.c:2190 [inline]
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_core+0xa86/0x1830 kernel/rcu/tree.c:2471
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline]
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: nfqnl_flush net/netfilter/nfnetlink_queue.c:405 [inline]
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: instance_destroy_rcu+0x30/0x220 net/netfilter/nfnetlink_queue.c:172
stack backtrace:
CPU: 0 PID: 13427 Comm: syz-executor.4 Not tainted 6.9.0-rc7-syzkaller-02060-g5c1672705a1a #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
lockdep_rcu_suspicious+0x221/0x340 kernel/locking/lockdep.c:6712
nf_reinject net/netfilter/nfnetlink_queue.c:323 [inline]
nfqnl_reinject+0x6ec/0x1120 net/netfilter/nfnetlink_queue.c:397
nfqnl_flush net/netfilter/nfnetlink_queue.c:410 [inline]
instance_destroy_rcu+0x1ae/0x220 net/netfilter/nfnetlink_queue.c:172
rcu_do_batch kernel/rcu/tree.c:2196 [inline]
rcu_core+0xafd/0x1830 kernel/rcu/tree.c:2471
handle_softirqs+0x2d6/0x990 kernel/softirq.c:554
__do_softirq kernel/softirq.c:588 [inline]
invoke_softirq kernel/softirq.c:428 [inline]
__irq_exit_rcu+0xf4/0x1c0 kernel/softirq.c:637
irq_exit_rcu+0x9/0x30 kernel/softirq.c:649
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1043 [inline]
sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1043
</IRQ>
<TASK>
Fixes: 9872bec773c2 ("[NETFILTER]: nfnetlink: use RCU for queue instances hash")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
A recent change to inet_dump_ifaddr had the function incorrectly iterate
over net rather than tgt_net, resulting in the data coming for the
incorrect network namespace.
Fixes: cdb2f80f1c10 ("inet: use xa_array iterator to implement inet_dump_ifaddr()")
Reported-by: Stéphane Graber <stgraber@stgraber.org>
Closes: https://github.com/lxc/incus/issues/892
Bisected-by: Stéphane Graber <stgraber@stgraber.org>
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Tested-by: Stéphane Graber <stgraber@stgraber.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240528203030.10839-1-aleksandr.mikhalitsyn@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
__dst_negative_advice() does not enforce proper RCU rules when
sk->dst_cache must be cleared, leading to possible UAF.
RCU rules are that we must first clear sk->sk_dst_cache,
then call dst_release(old_dst).
Note that sk_dst_reset(sk) is implementing this protocol correctly,
while __dst_negative_advice() uses the wrong order.
Given that ip6_negative_advice() has special logic
against RTF_CACHE, this means each of the three ->negative_advice()
existing methods must perform the sk_dst_reset() themselves.
Note the check against NULL dst is centralized in
__dst_negative_advice(), there is no need to duplicate
it in various callbacks.
Many thanks to Clement Lecigne for tracking this issue.
This old bug became visible after the blamed commit, using UDP sockets.
Fixes: a87cb3e48ee8 ("net: Facility to report route quality of connected sockets")
Reported-by: Clement Lecigne <clecigne@google.com>
Diagnosed-by: Clement Lecigne <clecigne@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240528114353.1794151-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
It is possible for syzbot to side-step the restriction imposed by the
blamed commit in the Fixes: tag, because the taprio UAPI permits a
cycle-time different from (and potentially shorter than) the sum of
entry intervals.
We need one more restriction, which is that the cycle time itself must
be larger than N * ETH_ZLEN bit times, where N is the number of schedule
entries. This restriction needs to apply regardless of whether the cycle
time came from the user or was the implicit, auto-calculated value, so
we move the existing "cycle == 0" check outside the "if "(!new->cycle_time)"
branch. This way covers both conditions and scenarios.
Add a selftest which illustrates the issue triggered by syzbot.
Fixes: b5b73b26b3ca ("taprio: Fix allowing too small intervals")
Reported-by: syzbot+a7d2b1d5d1af83035567@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000007d66bc06196e7c66@google.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20240527153955.553333-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In commit b5b73b26b3ca ("taprio: Fix allowing too small intervals"), a
comparison of user input against length_to_duration(q, ETH_ZLEN) was
introduced, to avoid RCU stalls due to frequent hrtimers.
The implementation of length_to_duration() depends on q->picos_per_byte
being set for the link speed. The blamed commit in the Fixes: tag has
moved this too late, so the checks introduced above are ineffective.
The q->picos_per_byte is zero at parse_taprio_schedule() ->
parse_sched_list() -> parse_sched_entry() -> fill_sched_entry() time.
Move the taprio_set_picos_per_byte() call as one of the first things in
taprio_change(), before the bulk of the netlink attribute parsing is
done. That's because it is needed there.
Add a selftest to make sure the issue doesn't get reintroduced.
Fixes: 09dbdf28f9f9 ("net/sched: taprio: fix calculation of maximum gate durations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240527153955.553333-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
sk_psock_get will return NULL if the refcount of psock has gone to 0, which
will happen when the last call of sk_psock_put is done. However,
sk_psock_drop may not have finished yet, so the close callback will still
point to sock_map_close despite psock being NULL.
This can be reproduced with a thread deleting an element from the sock map,
while the second one creates a socket, adds it to the map and closes it.
That will trigger the WARN_ON_ONCE:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 7220 at net/core/sock_map.c:1701 sock_map_close+0x2a2/0x2d0 net/core/sock_map.c:1701
Modules linked in:
CPU: 1 PID: 7220 Comm: syz-executor380 Not tainted 6.9.0-syzkaller-07726-g3c999d1ae3c7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
RIP: 0010:sock_map_close+0x2a2/0x2d0 net/core/sock_map.c:1701
Code: df e8 92 29 88 f8 48 8b 1b 48 89 d8 48 c1 e8 03 42 80 3c 20 00 74 08 48 89 df e8 79 29 88 f8 4c 8b 23 eb 89 e8 4f 15 23 f8 90 <0f> 0b 90 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d e9 13 26 3d 02
RSP: 0018:ffffc9000441fda8 EFLAGS: 00010293
RAX: ffffffff89731ae1 RBX: ffffffff94b87540 RCX: ffff888029470000
RDX: 0000000000000000 RSI: ffffffff8bcab5c0 RDI: ffffffff8c1faba0
RBP: 0000000000000000 R08: ffffffff92f9b61f R09: 1ffffffff25f36c3
R10: dffffc0000000000 R11: fffffbfff25f36c4 R12: ffffffff89731840
R13: ffff88804b587000 R14: ffff88804b587000 R15: ffffffff89731870
FS: 000055555e080380(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000207d4000 CR4: 0000000000350ef0
Call Trace:
<TASK>
unix_release+0x87/0xc0 net/unix/af_unix.c:1048
__sock_release net/socket.c:659 [inline]
sock_close+0xbe/0x240 net/socket.c:1421
__fput+0x42b/0x8a0 fs/file_table.c:422
__do_sys_close fs/open.c:1556 [inline]
__se_sys_close fs/open.c:1541 [inline]
__x64_sys_close+0x7f/0x110 fs/open.c:1541
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fb37d618070
Code: 00 00 48 c7 c2 b8 ff ff ff f7 d8 64 89 02 b8 ff ff ff ff eb d4 e8 10 2c 00 00 80 3d 31 f0 07 00 00 74 17 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 48 c3 0f 1f 80 00 00 00 00 48 83 ec 18 89 7c
RSP: 002b:00007ffcd4a525d8 EFLAGS: 00000202 ORIG_RAX: 0000000000000003
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fb37d618070
RDX: 0000000000000010 RSI: 00000000200001c0 RDI: 0000000000000004
RBP: 0000000000000000 R08: 0000000100000000 R09: 0000000100000000
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Use sk_psock, which will only check that the pointer is not been set to
NULL yet, which should only happen after the callbacks are restored. If,
then, a reference can still be gotten, we may call sk_psock_stop and cancel
psock->work.
As suggested by Paolo Abeni, reorder the condition so the control flow is
less convoluted.
After that change, the reproducer does not trigger the WARN_ON_ONCE
anymore.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot+07a2e4a1a57118ef7355@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=07a2e4a1a57118ef7355
Fixes: aadb2bb83ff7 ("sock_map: Fix a potential use-after-free in sock_map_close()")
Fixes: 5b4a79ba65a1 ("bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself")
Cc: stable@vger.kernel.org
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20240524144702.1178377-1-cascardo@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Jason commit made checks against ACK sequence less strict
and can be exploited by attackers to establish spoofed flows
with less probes.
Innocent users might use tcp_rmem[1] == 1,000,000,000,
or something more reasonable.
An attacker can use a regular TCP connection to learn the server
initial tp->rcv_wnd, and use it to optimize the attack.
If we make sure that only the announced window (smaller than 65535)
is used for ACK validation, we force an attacker to use
65537 packets to complete the 3WHS (assuming server ISN is unknown)
Fixes: 378979e94e95 ("tcp: remove 64 KByte limit for initial tp->rcv_wnd value")
Link: https://datatracker.ietf.org/meeting/119/materials/slides-119-tcpm-ghost-acks-00
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/r/20240523130528.60376-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Syzkaller was able to trigger
kernel BUG at net/core/gro.c:424 !
RIP: 0010:gro_pull_from_frag0 net/core/gro.c:424 [inline]
RIP: 0010:gro_try_pull_from_frag0 net/core/gro.c:446 [inline]
RIP: 0010:dev_gro_receive+0x242f/0x24b0 net/core/gro.c:571
Due to using an incorrect NAPI_GRO_CB(skb)->network_offset.
The referenced commit sets this offset to 0 in skb_gro_reset_offset.
That matches the expected case in dev_gro_receive:
pp = INDIRECT_CALL_INET(ptype->callbacks.gro_receive,
ipv6_gro_receive, inet_gro_receive,
&gro_list->list, skb);
But syzkaller injected an skb with protocol ETH_P_TEB into an ip6gre
device (by writing the IP6GRE encapsulated version to a TAP device).
The result was a first call to eth_gro_receive, and thus an extra
ETH_HLEN in network_offset that should not be there. First issue hit
is when computing offset from network header in ipv6_gro_pull_exthdrs.
Initialize both offsets in the network layer gro_receive.
This pairs with all reads in gro_receive, which use
skb_gro_receive_network_offset().
Fixes: 186b1ea73ad8 ("net: gro: use cb instead of skb->network_header")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240523141434.1752483-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Cited commit started returning an error when user space requests to dump
the interface's IPv4 addresses and IPv4 is disabled on the interface.
Restore the previous behavior and do not return an error.
Before cited commit:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether e2:40:68:98:d0:18 brd ff:ff:ff:ff:ff:ff
inet6 fe80::e040:68ff:fe98:d018/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 67 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether e2:40:68:98:d0:18 brd ff:ff:ff:ff:ff:ff
After cited commit:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 32:2d:69:f2:9c:99 brd ff:ff:ff:ff:ff:ff
inet6 fe80::302d:69ff:fef2:9c99/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
RTNETLINK answers: No such device
Dump terminated
With this patch:
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether de:17:56:bb:57:c0 brd ff:ff:ff:ff:ff:ff
inet6 fe80::dc17:56ff:febb:57c0/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
# ip link set dev dummy1 mtu 67
# ip address show dev dummy1
10: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 67 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether de:17:56:bb:57:c0 brd ff:ff:ff:ff:ff:ff
I fixed the exact same issue for IPv6 in commit c04f7dfe6ec2 ("ipv6: Fix
address dump when IPv6 is disabled on an interface"), but noted [1] that
I am not doing the change for IPv4 because I am not aware of a way to
disable IPv4 on an interface other than unregistering it. I clearly
missed the above case.
[1] https://lore.kernel.org/netdev/20240321173042.2151756-1-idosch@nvidia.com/
Fixes: cdb2f80f1c10 ("inet: use xa_array iterator to implement inet_dump_ifaddr()")
Reported-by: Carolina Jubran <cjubran@nvidia.com>
Reported-by: Yamen Safadi <ysafadi@nvidia.com>
Tested-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240523110257.334315-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-05-27
We've added 15 non-merge commits during the last 7 day(s) which contain
a total of 18 files changed, 583 insertions(+), 55 deletions(-).
The main changes are:
1) Fix broken BPF multi-uprobe PID filtering logic which filtered by thread
while the promise was to filter by process, from Andrii Nakryiko.
2) Fix the recent influx of syzkaller reports to sockmap which triggered
a locking rule violation by performing a map_delete, from Jakub Sitnicki.
3) Fixes to netkit driver in particular on skb->pkt_type override upon pass
verdict, from Daniel Borkmann.
4) Fix an integer overflow in resolve_btfids which can wrongly trigger build
failures, from Friedrich Vock.
5) Follow-up fixes for ARC JIT reported by static analyzers,
from Shahab Vahedi.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Cover verifier checks for mutating sockmap/sockhash
Revert "bpf, sockmap: Prevent lock inversion deadlock in map delete elem"
bpf: Allow delete from sockmap/sockhash only if update is allowed
selftests/bpf: Add netkit test for pkt_type
selftests/bpf: Add netkit tests for mac address
netkit: Fix pkt_type override upon netkit pass verdict
netkit: Fix setting mac address in l2 mode
ARC, bpf: Fix issues reported by the static analyzers
selftests/bpf: extend multi-uprobe tests with USDTs
selftests/bpf: extend multi-uprobe tests with child thread case
libbpf: detect broken PID filtering logic for multi-uprobe
bpf: remove unnecessary rcu_read_{lock,unlock}() in multi-uprobe attach logic
bpf: fix multi-uprobe PID filtering logic
bpf: Fix potential integer overflow in resolve_btfids
MAINTAINERS: Add myself as reviewer of ARM64 BPF JIT
====================
Link: https://lore.kernel.org/r/20240527203551.29712-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This reverts commit ff91059932401894e6c86341915615c5eb0eca48.
This check is no longer needed. BPF programs attached to tracepoints are
now rejected by the verifier when they attempt to delete from a
sockmap/sockhash maps.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20240527-sockmap-verify-deletes-v1-2-944b372f2101@cloudflare.com
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When running Cilium connectivity test suite with netkit in L2 mode, we
found that compared to tcx a few tests were failing which pushed traffic
into an L7 proxy sitting in host namespace. The problem in particular is
around the invocation of eth_type_trans() in netkit.
In case of tcx, this is run before the tcx ingress is triggered inside
host namespace and thus if the BPF program uses the bpf_skb_change_type()
helper the newly set type is retained. However, in case of netkit, the
late eth_type_trans() invocation overrides the earlier decision from the
BPF program which eventually leads to the test failure.
Instead of eth_type_trans(), split out the relevant parts, meaning, reset
of mac header and call to eth_skb_pkt_type() before the BPF program is run
in order to have the same behavior as with tcx, and refactor a small helper
called eth_skb_pull_mac() which is run in case it's passed up the stack
where the mac header must be pulled. With this all connectivity tests pass.
Fixes: 35dfaad7188c ("netkit, bpf: Add bpf programmable net device")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240524163619.26001-2-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
syzkaller reported data-race of sk->sk_hash in unix_autobind() [0],
and the same ones exist in unix_bind_bsd() and unix_bind_abstract().
The three bind() functions prefetch sk->sk_hash locklessly and
use it later after validating that unix_sk(sk)->addr is NULL under
unix_sk(sk)->bindlock.
The prefetched sk->sk_hash is the hash value of unbound socket set
in unix_create1() and does not change until bind() completes.
There could be a chance that sk->sk_hash changes after the lockless
read. However, in such a case, non-NULL unix_sk(sk)->addr is visible
under unix_sk(sk)->bindlock, and bind() returns -EINVAL without using
the prefetched value.
The KCSAN splat is false-positive, but let's silence it by reading
sk->sk_hash under unix_sk(sk)->bindlock.
[0]:
BUG: KCSAN: data-race in unix_autobind / unix_autobind
write to 0xffff888034a9fb88 of 4 bytes by task 4468 on cpu 0:
__unix_set_addr_hash net/unix/af_unix.c:331 [inline]
unix_autobind+0x47a/0x7d0 net/unix/af_unix.c:1185
unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373
__sys_connect_file+0xd7/0xe0 net/socket.c:2048
__sys_connect+0x114/0x140 net/socket.c:2065
__do_sys_connect net/socket.c:2075 [inline]
__se_sys_connect net/socket.c:2072 [inline]
__x64_sys_connect+0x40/0x50 net/socket.c:2072
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x46/0x4e
read to 0xffff888034a9fb88 of 4 bytes by task 4465 on cpu 1:
unix_autobind+0x28/0x7d0 net/unix/af_unix.c:1134
unix_dgram_connect+0x7e3/0x890 net/unix/af_unix.c:1373
__sys_connect_file+0xd7/0xe0 net/socket.c:2048
__sys_connect+0x114/0x140 net/socket.c:2065
__do_sys_connect net/socket.c:2075 [inline]
__se_sys_connect net/socket.c:2072 [inline]
__x64_sys_connect+0x40/0x50 net/socket.c:2072
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x46/0x4e
value changed: 0x000000e4 -> 0x000001e3
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 4465 Comm: syz-executor.0 Not tainted 6.8.0-12822-gcd51db110a7e #12
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Fixes: afd20b9290e1 ("af_unix: Replace the big lock with small locks.")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240522154218.78088-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Once unix_sk(sk)->addr is assigned under net->unx.table.locks and
unix_sk(sk)->bindlock, *(unix_sk(sk)->addr) and unix_sk(sk)->path are
fully set up, and unix_sk(sk)->addr is never changed.
unix_getname() and unix_copy_addr() access the two fields locklessly,
and commit ae3b564179bf ("missing barriers in some of unix_sock ->addr
and ->path accesses") added smp_store_release() and smp_load_acquire()
pairs.
In other functions, we still read unix_sk(sk)->addr locklessly to check
if the socket is bound, and KCSAN complains about it. [0]
Given these functions have no dependency for *(unix_sk(sk)->addr) and
unix_sk(sk)->path, READ_ONCE() is enough to annotate the data-race.
Note that it is safe to access unix_sk(sk)->addr locklessly if the socket
is found in the hash table. For example, the lockless read of otheru->addr
in unix_stream_connect() is safe.
Note also that newu->addr there is of the child socket that is still not
accessible from userspace, and smp_store_release() publishes the address
in case the socket is accept()ed and unix_getname() / unix_copy_addr()
is called.
[0]:
BUG: KCSAN: data-race in unix_bind / unix_listen
write (marked) to 0xffff88805f8d1840 of 8 bytes by task 13723 on cpu 0:
__unix_set_addr_hash net/unix/af_unix.c:329 [inline]
unix_bind_bsd net/unix/af_unix.c:1241 [inline]
unix_bind+0x881/0x1000 net/unix/af_unix.c:1319
__sys_bind+0x194/0x1e0 net/socket.c:1847
__do_sys_bind net/socket.c:1858 [inline]
__se_sys_bind net/socket.c:1856 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1856
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x46/0x4e
read to 0xffff88805f8d1840 of 8 bytes by task 13724 on cpu 1:
unix_listen+0x72/0x180 net/unix/af_unix.c:734
__sys_listen+0xdc/0x160 net/socket.c:1881
__do_sys_listen net/socket.c:1890 [inline]
__se_sys_listen net/socket.c:1888 [inline]
__x64_sys_listen+0x2e/0x40 net/socket.c:1888
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x4f/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x46/0x4e
value changed: 0x0000000000000000 -> 0xffff88807b5b1b40
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 13724 Comm: syz-executor.4 Not tainted 6.8.0-12822-gcd51db110a7e #12
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240522154002.77857-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull 9p fixes from Dominique Martinet:
"Two fixes headed to stable trees:
- a trace event was dumping uninitialized values
- a missing lock that was thought to have exclusive access, and it
turned out not to"
* tag '9p-for-6.10-rc2' of https://github.com/martinetd/linux:
9p: add missing locking around taking dentry fid list
net/9p: fix uninit-value in p9_client_rpc()
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Syzbot with the help of KMSAN reported the following error:
BUG: KMSAN: uninit-value in trace_9p_client_res include/trace/events/9p.h:146 [inline]
BUG: KMSAN: uninit-value in p9_client_rpc+0x1314/0x1340 net/9p/client.c:754
trace_9p_client_res include/trace/events/9p.h:146 [inline]
p9_client_rpc+0x1314/0x1340 net/9p/client.c:754
p9_client_create+0x1551/0x1ff0 net/9p/client.c:1031
v9fs_session_init+0x1b9/0x28e0 fs/9p/v9fs.c:410
v9fs_mount+0xe2/0x12b0 fs/9p/vfs_super.c:122
legacy_get_tree+0x114/0x290 fs/fs_context.c:662
vfs_get_tree+0xa7/0x570 fs/super.c:1797
do_new_mount+0x71f/0x15e0 fs/namespace.c:3352
path_mount+0x742/0x1f20 fs/namespace.c:3679
do_mount fs/namespace.c:3692 [inline]
__do_sys_mount fs/namespace.c:3898 [inline]
__se_sys_mount+0x725/0x810 fs/namespace.c:3875
__x64_sys_mount+0xe4/0x150 fs/namespace.c:3875
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Uninit was created at:
__alloc_pages+0x9d6/0xe70 mm/page_alloc.c:4598
__alloc_pages_node include/linux/gfp.h:238 [inline]
alloc_pages_node include/linux/gfp.h:261 [inline]
alloc_slab_page mm/slub.c:2175 [inline]
allocate_slab mm/slub.c:2338 [inline]
new_slab+0x2de/0x1400 mm/slub.c:2391
___slab_alloc+0x1184/0x33d0 mm/slub.c:3525
__slab_alloc mm/slub.c:3610 [inline]
__slab_alloc_node mm/slub.c:3663 [inline]
slab_alloc_node mm/slub.c:3835 [inline]
kmem_cache_alloc+0x6d3/0xbe0 mm/slub.c:3852
p9_tag_alloc net/9p/client.c:278 [inline]
p9_client_prepare_req+0x20a/0x1770 net/9p/client.c:641
p9_client_rpc+0x27e/0x1340 net/9p/client.c:688
p9_client_create+0x1551/0x1ff0 net/9p/client.c:1031
v9fs_session_init+0x1b9/0x28e0 fs/9p/v9fs.c:410
v9fs_mount+0xe2/0x12b0 fs/9p/vfs_super.c:122
legacy_get_tree+0x114/0x290 fs/fs_context.c:662
vfs_get_tree+0xa7/0x570 fs/super.c:1797
do_new_mount+0x71f/0x15e0 fs/namespace.c:3352
path_mount+0x742/0x1f20 fs/namespace.c:3679
do_mount fs/namespace.c:3692 [inline]
__do_sys_mount fs/namespace.c:3898 [inline]
__se_sys_mount+0x725/0x810 fs/namespace.c:3875
__x64_sys_mount+0xe4/0x150 fs/namespace.c:3875
do_syscall_64+0xd5/0x1f0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
If p9_check_errors() fails early in p9_client_rpc(), req->rc.tag
will not be properly initialized. However, trace_9p_client_res()
ends up trying to print it out anyway before p9_client_rpc()
finishes.
Fix this issue by assigning default values to p9_fcall fields
such as 'tag' and (just in case KMSAN unearths something new) 'id'
during the tag allocation stage.
Reported-and-tested-by: syzbot+ff14db38f56329ef68df@syzkaller.appspotmail.com
Fixes: 348b59012e5c ("net/9p: Convert net/9p protocol dumps to tracepoints")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Cc: stable@vger.kernel.org
Message-ID: <20240408141039.30428-1-n.zhandarovich@fintech.ru>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
|
| |\ \ \ \ \
| |_|/ / /
|/| | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull NFS client updates from Trond Myklebust:
"Stable fixes:
- nfs: fix undefined behavior in nfs_block_bits()
- NFSv4.2: Fix READ_PLUS when server doesn't support OP_READ_PLUS
Bugfixes:
- Fix mixing of the lock/nolock and local_lock mount options
- NFSv4: Fixup smatch warning for ambiguous return
- NFSv3: Fix remount when using the legacy binary mount api
- SUNRPC: Fix the handling of expired RPCSEC_GSS contexts
- SUNRPC: fix the NFSACL RPC retries when soft mounts are enabled
- rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
Features and cleanups:
- NFSv3: Use the atomic_open API to fix open(O_CREAT|O_TRUNC)
- pNFS/filelayout: S layout segment range in LAYOUTGET
- pNFS: rework pnfs_generic_pg_check_layout to check IO range
- NFSv2: Turn off enabling of NFS v2 by default"
* tag 'nfs-for-6.10-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix undefined behavior in nfs_block_bits()
pNFS: rework pnfs_generic_pg_check_layout to check IO range
pNFS/filelayout: check layout segment range
pNFS/filelayout: fixup pNfs allocation modes
rpcrdma: fix handling for RDMA_CM_EVENT_DEVICE_REMOVAL
NFS: Don't enable NFS v2 by default
NFS: Fix READ_PLUS when server doesn't support OP_READ_PLUS
sunrpc: fix NFSACL RPC retry on soft mount
SUNRPC: fix handling expired GSS context
nfs: keep server info for remounts
NFSv4: Fixup smatch warning for ambiguous return
NFS: make sure lock/nolock overriding local_lock mount option
NFS: add atomic_open for NFSv3 to handle O_TRUNC correctly.
pNFS/filelayout: Specify the layout segment range in LAYOUTGET
pNFS/filelayout: Remove the whole file layout requirement
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Under the scenario of IB device bonding, when bringing down one of the
ports, or all ports, we saw xprtrdma entering a non-recoverable state
where it is not even possible to complete the disconnect and shut it
down the mount, requiring a reboot. Following debug, we saw that
transport connect never ended after receiving the
RDMA_CM_EVENT_DEVICE_REMOVAL callback.
The DEVICE_REMOVAL callback is irrespective of whether the CM_ID is
connected, and ESTABLISHED may not have happened. So need to work with
each of these states accordingly.
Fixes: 2acc5cae2923 ('xprtrdma: Prevent dereferencing r_xprt->rx_ep after it is freed')
Cc: Sagi Grimberg <sagi.grimberg@vastdata.com>
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
It used to be quite awhile ago since 1b63a75180c6 ('SUNRPC: Refactor
rpc_clone_client()'), in 2012, that `cl_timeout` was copied in so that
all mount parameters propagate to NFSACL clients. However since that
change, if mount options as follows are given:
soft,timeo=50,retrans=16,vers=3
The resultant NFSACL client receives:
cl_softrtry: 1
cl_timeout: to_initval=60000, to_maxval=60000, to_increment=0, to_retries=2, to_exponential=0
These values lead to NFSACL operations not being retried under the
condition of transient network outages with soft mount. Instead, getacl
call fails after 60 seconds with EIO.
The simple fix is to pass the existing client's `cl_timeout` as the new
client timeout.
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Link: https://lore.kernel.org/all/20231105154857.ryakhmgaptq3hb6b@gmail.com/T/
Fixes: 1b63a75180c6 ('SUNRPC: Refactor rpc_clone_client()')
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In the case where we have received a successful reply to an RPC request,
but while processing the reply the client in rpc_decode_header() finds
an expired context, the code ends up propagating the error to the caller
instead of getting a new context and retrying the request.
To give more details, in rpc_decode_header() we call rpcauth_checkverf()
will call into the gss and internally will at some point call
gss_validate() which has a check if the current’s context lifetime
expired, and it would fail. The reason for the failure gets ‘scrubbed’
and translated to EACCES so when we get back to rpc_decode_header() we
just go to “out_verifier” which for that error would get converted to
“out_garbage” (ie it’s treated as garballed reply) and the next
action is call_encode. Which (1) doesn’t reencode or re-send (not to
mention no upcall happens because context expires as that reason just
not known) and it again fails in the same decoding process. After
re-trying it 3 times the error is propagated back to the caller
(ie nfs4_write_done_cb() in the case a failing write).
To fix this, instead we need to look to the case where the server
decides that context has expired and replies with an RPC auth error.
In that case, the rpc_decode_header() goes to "out_msg_denied" in that
we return EKEYREJECTED which in call_decode() is sent to “call_reserve”
which triggers an upcalls and a re-try of the operation.
The proposed fix is in case of a failed rpc_decode_header() to check
if credentials were set to be invalid and use that as a proxy for
deciding that context has expired and then treat is same way as
receiving an auth error.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Quite smaller than usual. Notably it includes the fix for the unix
regression from the past weeks. The TCP window fix will require some
follow-up, already queued.
Current release - regressions:
- af_unix: fix garbage collection of embryos
Previous releases - regressions:
- af_unix: fix race between GC and receive path
- ipv6: sr: fix missing sk_buff release in seg6_input_core
- tcp: remove 64 KByte limit for initial tp->rcv_wnd value
- eth: r8169: fix rx hangup
- eth: lan966x: remove ptp traps in case the ptp is not enabled
- eth: ixgbe: fix link breakage vs cisco switches
- eth: ice: prevent ethtool from corrupting the channels
Previous releases - always broken:
- openvswitch: set the skbuff pkt_type for proper pmtud support
- tcp: Fix shift-out-of-bounds in dctcp_update_alpha()
Misc:
- a bunch of selftests stabilization patches"
* tag 'net-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (25 commits)
r8169: Fix possible ring buffer corruption on fragmented Tx packets.
idpf: Interpret .set_channels() input differently
ice: Interpret .set_channels() input differently
nfc: nci: Fix handling of zero-length payload packets in nci_rx_work()
net: relax socket state check at accept time.
tcp: remove 64 KByte limit for initial tp->rcv_wnd value
net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe()
tls: fix missing memory barrier in tls_init
net: fec: avoid lock evasion when reading pps_enable
Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"
testing: net-drv: use stats64 for testing
net: mana: Fix the extra HZ in mana_hwc_send_request
net: lan966x: Remove ptp traps in case the ptp is not enabled.
openvswitch: Set the skbuff pkt_type for proper pmtud support.
selftest: af_unix: Make SCM_RIGHTS into OOB data.
af_unix: Fix garbage collection of embryos carrying OOB with SCM_RIGHTS
tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
selftests/net: use tc rule to filter the na packet
ipv6: sr: fix memleak in seg6_hmac_init_algo
af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock.
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When nci_rx_work() receives a zero-length payload packet, it should not
discard the packet and exit the loop. Instead, it should continue
processing subsequent packets.
Fixes: d24b03535e5e ("nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet")
Signed-off-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240521153444.535399-1-ryasuoka@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Christoph reported the following splat:
WARNING: CPU: 1 PID: 772 at net/ipv4/af_inet.c:761 __inet_accept+0x1f4/0x4a0
Modules linked in:
CPU: 1 PID: 772 Comm: syz-executor510 Not tainted 6.9.0-rc7-g7da7119fe22b #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
RIP: 0010:__inet_accept+0x1f4/0x4a0 net/ipv4/af_inet.c:759
Code: 04 38 84 c0 0f 85 87 00 00 00 41 c7 04 24 03 00 00 00 48 83 c4 10 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 ec b7 da fd <0f> 0b e9 7f fe ff ff e8 e0 b7 da fd 0f 0b e9 fe fe ff ff 89 d9 80
RSP: 0018:ffffc90000c2fc58 EFLAGS: 00010293
RAX: ffffffff836bdd14 RBX: 0000000000000000 RCX: ffff888104668000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: dffffc0000000000 R08: ffffffff836bdb89 R09: fffff52000185f64
R10: dffffc0000000000 R11: fffff52000185f64 R12: dffffc0000000000
R13: 1ffff92000185f98 R14: ffff88810754d880 R15: ffff8881007b7800
FS: 000000001c772880(0000) GS:ffff88811b280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb9fcf2e178 CR3: 00000001045d2002 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
inet_accept+0x138/0x1d0 net/ipv4/af_inet.c:786
do_accept+0x435/0x620 net/socket.c:1929
__sys_accept4_file net/socket.c:1969 [inline]
__sys_accept4+0x9b/0x110 net/socket.c:1999
__do_sys_accept net/socket.c:2016 [inline]
__se_sys_accept net/socket.c:2013 [inline]
__x64_sys_accept+0x7d/0x90 net/socket.c:2013
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x58/0x100 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x4315f9
Code: fd ff 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 ab b4 fd ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffdb26d9c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002b
RAX: ffffffffffffffda RBX: 0000000000400300 RCX: 00000000004315f9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000004
RBP: 00000000006e1018 R08: 0000000000400300 R09: 0000000000400300
R10: 0000000000400300 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000040cdf0 R14: 000000000040ce80 R15: 0000000000000055
</TASK>
The reproducer invokes shutdown() before entering the listener status.
After commit 94062790aedb ("tcp: defer shutdown(SEND_SHUTDOWN) for
TCP_SYN_RECV sockets"), the above causes the child to reach the accept
syscall in FIN_WAIT1 status.
Eric noted we can relax the existing assertion in __inet_accept()
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/490
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: 94062790aedb ("tcp: defer shutdown(SEND_SHUTDOWN) for TCP_SYN_RECV sockets")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/23ab880a44d8cfd967e84de8b93dbf48848e3d8c.1716299669.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Recently, we had some servers upgraded to the latest kernel and noticed
the indicator from the user side showed worse results than before. It is
caused by the limitation of tp->rcv_wnd.
In 2018 commit a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin
to around 64KB") limited the initial value of tp->rcv_wnd to 65535, most
CDN teams would not benefit from this change because they cannot have a
large window to receive a big packet, which will be slowed down especially
in long RTT. Small rcv_wnd means slow transfer speed, to some extent. It's
the side effect for the latency/time-sensitive users.
To avoid future confusion, current change doesn't affect the initial
receive window on the wire in a SYN or SYN+ACK packet which are set within
65535 bytes according to RFC 7323 also due to the limit in
__tcp_transmit_skb():
th->window = htons(min(tp->rcv_wnd, 65535U));
In one word, __tcp_transmit_skb() already ensures that constraint is
respected, no matter how large tp->rcv_wnd is. The change doesn't violate
RFC.
Let me provide one example if with or without the patch:
Before:
client --- SYN: rwindow=65535 ---> server
client <--- SYN+ACK: rwindow=65535 ---- server
client --- ACK: rwindow=65536 ---> server
Note: for the last ACK, the calculation is 512 << 7.
After:
client --- SYN: rwindow=65535 ---> server
client <--- SYN+ACK: rwindow=65535 ---- server
client --- ACK: rwindow=175232 ---> server
Note: I use the following command to make it work:
ip route change default via [ip] dev eth0 metric 100 initrwnd 120
For the last ACK, the calculation is 1369 << 7.
When we apply such a patch, having a large rcv_wnd if the user tweak this
knob can help transfer data more rapidly and save some rtts.
Fixes: a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20240521134220.12510-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In tls_init(), a write memory barrier is missing, and store-store
reordering may cause NULL dereference in tls_{setsockopt,getsockopt}.
CPU0 CPU1
----- -----
// In tls_init()
// In tls_ctx_create()
ctx = kzalloc()
ctx->sk_proto = READ_ONCE(sk->sk_prot) -(1)
// In update_sk_prot()
WRITE_ONCE(sk->sk_prot, tls_prots) -(2)
// In sock_common_setsockopt()
READ_ONCE(sk->sk_prot)->setsockopt()
// In tls_{setsockopt,getsockopt}()
ctx->sk_proto->setsockopt() -(3)
In the above scenario, when (1) and (2) are reordered, (3) can observe
the NULL value of ctx->sk_proto, causing NULL dereference.
To fix it, we rely on rcu_assign_pointer() which implies the release
barrier semantic. By moving rcu_assign_pointer() after ctx->sk_proto is
initialized, we can ensure that ctx->sk_proto are visible when
changing sk->sk_prot.
Fixes: d5bee7374b68 ("net/tls: Annotate access to sk_prot with READ_ONCE/WRITE_ONCE")
Signed-off-by: Yewon Choi <woni9911@gmail.com>
Signed-off-by: Dae R. Jeong <threeearcat@gmail.com>
Link: https://lore.kernel.org/netdev/ZU4OJG56g2V9z_H7@dragonet/T/
Link: https://lore.kernel.org/r/Zkx4vjSFp0mfpjQ2@libra05
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5a7 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
GC attempts to explicitly drop oob_skb's reference before purging the hit
list.
The problem is with embryos: kfree_skb(u->oob_skb) is never called on an
embryo socket.
The python script below [0] sends a listener's fd to its embryo as OOB
data. While GC does collect the embryo's queue, it fails to drop the OOB
skb's refcount. The skb which was in embryo's receive queue stays as
unix_sk(sk)->oob_skb and keeps the listener's refcount [1].
Tell GC to dispose embryo's oob_skb.
[0]:
from array import array
from socket import *
addr = '\x00unix-oob'
lis = socket(AF_UNIX, SOCK_STREAM)
lis.bind(addr)
lis.listen(1)
s = socket(AF_UNIX, SOCK_STREAM)
s.connect(addr)
scm = (SOL_SOCKET, SCM_RIGHTS, array('i', [lis.fileno()]))
s.sendmsg([b'x'], [scm], MSG_OOB)
lis.close()
[1]
$ grep unix-oob /proc/net/unix
$ ./unix-oob.py
$ grep unix-oob /proc/net/unix
0000000000000000: 00000002 00000000 00000000 0001 02 0 @unix-oob
0000000000000000: 00000002 00000000 00010000 0001 01 6072 @unix-oob
Fixes: 4090fa373f0e ("af_unix: Replace garbage collection algorithm.")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In dctcp_update_alpha(), we use a module parameter dctcp_shift_g
as follows:
alpha -= min_not_zero(alpha, alpha >> dctcp_shift_g);
...
delivered_ce <<= (10 - dctcp_shift_g);
It seems syzkaller started fuzzing module parameters and triggered
shift-out-of-bounds [0] by setting 100 to dctcp_shift_g:
memcpy((void*)0x20000080,
"/sys/module/tcp_dctcp/parameters/dctcp_shift_g\000", 47);
res = syscall(__NR_openat, /*fd=*/0xffffffffffffff9cul, /*file=*/0x20000080ul,
/*flags=*/2ul, /*mode=*/0ul);
memcpy((void*)0x20000000, "100\000", 4);
syscall(__NR_write, /*fd=*/r[0], /*val=*/0x20000000ul, /*len=*/4ul);
Let's limit the max value of dctcp_shift_g by param_set_uint_minmax().
With this patch:
# echo 10 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
# cat /sys/module/tcp_dctcp/parameters/dctcp_shift_g
10
# echo 11 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
-bash: echo: write error: Invalid argument
[0]:
UBSAN: shift-out-of-bounds in net/ipv4/tcp_dctcp.c:143:12
shift exponent 100 is too large for 32-bit type 'u32' (aka 'unsigned int')
CPU: 0 PID: 8083 Comm: syz-executor345 Not tainted 6.9.0-05151-g1b294a1f3561 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x300 lib/dump_stack.c:114
ubsan_epilogue lib/ubsan.c:231 [inline]
__ubsan_handle_shift_out_of_bounds+0x346/0x3a0 lib/ubsan.c:468
dctcp_update_alpha+0x540/0x570 net/ipv4/tcp_dctcp.c:143
tcp_in_ack_event net/ipv4/tcp_input.c:3802 [inline]
tcp_ack+0x17b1/0x3bc0 net/ipv4/tcp_input.c:3948
tcp_rcv_state_process+0x57a/0x2290 net/ipv4/tcp_input.c:6711
tcp_v4_do_rcv+0x764/0xc40 net/ipv4/tcp_ipv4.c:1937
sk_backlog_rcv include/net/sock.h:1106 [inline]
__release_sock+0x20f/0x350 net/core/sock.c:2983
release_sock+0x61/0x1f0 net/core/sock.c:3549
mptcp_subflow_shutdown+0x3d0/0x620 net/mptcp/protocol.c:2907
mptcp_check_send_data_fin+0x225/0x410 net/mptcp/protocol.c:2976
__mptcp_close+0x238/0xad0 net/mptcp/protocol.c:3072
mptcp_close+0x2a/0x1a0 net/mptcp/protocol.c:3127
inet_release+0x190/0x1f0 net/ipv4/af_inet.c:437
__sock_release net/socket.c:659 [inline]
sock_close+0xc0/0x240 net/socket.c:1421
__fput+0x41b/0x890 fs/file_table.c:422
task_work_run+0x23b/0x300 kernel/task_work.c:180
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0x9c8/0x2540 kernel/exit.c:878
do_group_exit+0x201/0x2b0 kernel/exit.c:1027
__do_sys_exit_group kernel/exit.c:1038 [inline]
__se_sys_exit_group kernel/exit.c:1036 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1036
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xe4/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x67/0x6f
RIP: 0033:0x7f6c2b5005b6
Code: Unable to access opcode bytes at 0x7f6c2b50058c.
RSP: 002b:00007ffe883eb948 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00007f6c2b5862f0 RCX: 00007f6c2b5005b6
RDX: 0000000000000001 RSI: 000000000000003c RDI: 0000000000000001
RBP: 0000000000000001 R08: 00000000000000e7 R09: ffffffffffffffc0
R10: 0000000000000006 R11: 0000000000000246 R12: 00007f6c2b5862f0
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
</TASK>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Reported-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Closes: https://lore.kernel.org/netdev/CAEkJfYNJM=cw-8x7_Vmj1J6uYVCWMbbvD=EFmDPVBGpTsqOxEA@mail.gmail.com/
Fixes: e3118e8359bb ("net: tcp: add DCTCP congestion control algorithm")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240517091626.32772-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
seg6_hmac_init_algo returns without cleaning up the previous allocations
if one fails, so it's going to leak all that memory and the crypto tfms.
Update seg6_hmac_exit to only free the memory when allocated, so we can
reuse the code directly.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Closes: https://lore.kernel.org/netdev/Zj3bh-gE7eT6V6aH@hog/
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240517005435.2600277-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Billy Jheng Bing-Jhong reported a race between __unix_gc() and
queue_oob().
__unix_gc() tries to garbage-collect close()d inflight sockets,
and then if the socket has MSG_OOB in unix_sk(sk)->oob_skb, GC
will drop the reference and set NULL to it locklessly.
However, the peer socket still can send MSG_OOB message and
queue_oob() can update unix_sk(sk)->oob_skb concurrently, leading
NULL pointer dereference. [0]
To fix the issue, let's update unix_sk(sk)->oob_skb under the
sk_receive_queue's lock and take it everywhere we touch oob_skb.
Note that we defer kfree_skb() in manage_oob() to silence lockdep
false-positive (See [1]).
[0]:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PF: supervisor write access in kernel mode
PF: error_code(0x0002) - not-present page
PGD 8000000009f5e067 P4D 8000000009f5e067 PUD 9f5d067 PMD 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 3 PID: 50 Comm: kworker/3:1 Not tainted 6.9.0-rc5-00191-gd091e579b864 #110
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events delayed_fput
RIP: 0010:skb_dequeue (./include/linux/skbuff.h:2386 ./include/linux/skbuff.h:2402 net/core/skbuff.c:3847)
Code: 39 e3 74 3e 8b 43 10 48 89 ef 83 e8 01 89 43 10 49 8b 44 24 08 49 c7 44 24 08 00 00 00 00 49 8b 14 24 49 c7 04 24 00 00 00 00 <48> 89 42 08 48 89 10 e8 e7 c5 42 00 4c 89 e0 5b 5d 41 5c c3 cc cc
RSP: 0018:ffffc900001bfd48 EFLAGS: 00000002
RAX: 0000000000000000 RBX: ffff8880088f5ae8 RCX: 00000000361289f9
RDX: 0000000000000000 RSI: 0000000000000206 RDI: ffff8880088f5b00
RBP: ffff8880088f5b00 R08: 0000000000080000 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000001 R12: ffff8880056b6a00
R13: ffff8880088f5280 R14: 0000000000000001 R15: ffff8880088f5a80
FS: 0000000000000000(0000) GS:ffff88807dd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000006314000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<TASK>
unix_release_sock (net/unix/af_unix.c:654)
unix_release (net/unix/af_unix.c:1050)
__sock_release (net/socket.c:660)
sock_close (net/socket.c:1423)
__fput (fs/file_table.c:423)
delayed_fput (fs/file_table.c:444 (discriminator 3))
process_one_work (kernel/workqueue.c:3259)
worker_thread (kernel/workqueue.c:3329 kernel/workqueue.c:3416)
kthread (kernel/kthread.c:388)
ret_from_fork (arch/x86/kernel/process.c:153)
ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
</TASK>
Modules linked in:
CR2: 0000000000000008
Link: https://lore.kernel.org/netdev/a00d3993-c461-43f2-be6d-07259c98509a@rbox.co/ [1]
Fixes: 1279f9d9dec2 ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Reported-by: Billy Jheng Bing-Jhong <billy@starlabs.sg>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240516134835.8332-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
syzbot reported the following uninit-value access issue [1]
nci_rx_work() parses received packet from ndev->rx_q. It should be
validated header size, payload size and total packet size before
processing the packet. If an invalid packet is detected, it should be
silently discarded.
Fixes: d24b03535e5e ("nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet")
Reported-and-tested-by: syzbot+d7b4dc6cd50410152534@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d7b4dc6cd50410152534 [1]
Signed-off-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The seg6_input() function is responsible for adding the SRH into a
packet, delegating the operation to the seg6_input_core(). This function
uses the skb_cow_head() to ensure that there is sufficient headroom in
the sk_buff for accommodating the link-layer header.
In the event that the skb_cow_header() function fails, the
seg6_input_core() catches the error but it does not release the sk_buff,
which will result in a memory leak.
This issue was introduced in commit af3b5158b89d ("ipv6: sr: fix BUG due
to headroom too small after SRH push") and persists even after commit
7a3f5b0de364 ("netfilter: add netfilter hooks to SRv6 data plane"),
where the entire seg6_input() code was refactored to deal with netfilter
hooks.
The proposed patch addresses the identified memory leak by requiring the
seg6_input_core() function to release the sk_buff in the event that
skb_cow_head() fails.
Fixes: af3b5158b89d ("ipv6: sr: fix BUG due to headroom too small after SRH push")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing cleanup from Steven Rostedt:
"Remove second argument of __assign_str()
The __assign_str() macro logic of the TRACE_EVENT() macro was
optimized so that it no longer needs the second argument. The
__assign_str() is always matched with __string() field that takes a
field name and the source for that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then
use that value to copy into the ring buffer via the __assign_str().
Before commit c1fa617caeb0 ("tracing: Rework __assign_str() and
__string() to not duplicate getting the string"), the __assign_str()
needed the second argument which would perform the same logic as the
__string() source parameter did. Not only would this add overhead, but
it was error prone as if the __assign_str() source produced something
different, it may not have allocated enough for the string in the ring
buffer (as the __string() source was used to determine how much to
allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be
removed"
* tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/treewide: Remove second parameter of __assign_str()
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
| |\ \ \ \
| |/ / /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
virtio core already sets the .owner, so driver does not need to.
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-19-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
virtio core already sets the .owner, so driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-18-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Switch read and write software bits for PUDs
- Add missing hardware bits for PUDs and PMDs
- Generate unwind information for C modules to fix GDB unwind error for
vDSO functions
- Create .build-id links for unstripped vDSO files to enable vDSO
debugging with symbols
- Use standard stack frame layout for vDSO generated stack frames to
manually walk stack frames without DWARF information
- Rework perf_callchain_user() and arch_stack_walk_user() functions to
reduce code duplication
- Skip first stack frame when walking user stack
- Add basic checks to identify invalid instruction pointers when
walking stack frames
- Introduce and use struct stack_frame_vdso_wrapper within vDSO user
wrapper code to automatically generate an asm-offset define. Also use
STACK_FRAME_USER_OVERHEAD instead of STACK_FRAME_OVERHEAD to document
that the code works with user space stack
- Clear the backchain of the extra stack frame added by the vDSO user
wrapper code. This allows the user stack walker to detect and skip
the non-standard stack frame. Without this an incorrect instruction
pointer would be added to stack traces.
- Rewrite psw_idle() function in C to ease maintenance and further
enhancements
- Remove get_vtimer() function and use get_cpu_timer() instead
- Mark psw variable in __load_psw_mask() as __unitialized to avoid
superfluous clearing of PSW
- Remove obsolete and superfluous comment about removed TIF_FPU flag
- Replace memzero_explicit() and kfree() with kfree_sensitive() to fix
warnings reported by Coccinelle
- Wipe sensitive data and all copies of protected- or secure-keys from
stack when an IOCTL fails
- Both do_airq_interrupt() and do_io_interrupt() functions set
CIF_NOHZ_DELAY flag. Move it in do_io_irq() to simplify the code
- Provide iucv_alloc_device() and iucv_release_device() helpers, which
can be used to deduplicate more or less identical IUCV device
allocation and release code in four different drivers
- Make use of iucv_alloc_device() and iucv_release_device() helpers to
get rid of quite some code and also remove a cast to an incompatible
function (clang W=1)
- There is no user of iucv_root outside of the core IUCV code left.
Therefore remove the EXPORT_SYMBOL
- __apply_alternatives() contains a runtime check which verifies that
the size of the to be patched code area is even. Convert this to a
compile time check
- Increase size of buffers for sending z/VM CP DIAGNOSE X'008' commands
from 128 to 240
- Do not accept z/VM CP DIAGNOSE X'008' commands longer than maximally
allowed
- Use correct defines IPL_BP_NVME_LEN and IPL_BP0_NVME_LEN instead of
IPL_BP_FCP_LEN and IPL_BP0_FCP_LEN ones to initialize NVMe reIPL
block on 'scp_data' sysfs attribute update
- Initialize the correct fields of the NVMe dump block, which were
confused with FCP fields
- Refactor macros for 'scp_data' (re-)IPL sysfs attribute to reduce
code duplication
- Introduce 'scp_data' sysfs attribute for dump IPL to allow tools such
as dumpconf passing additional kernel command line parameters to a
stand-alone dumper
- Rework the CPACF query functions to use the correct RRE or RRF
instruction formats and set instruction register fields correctly
- Instead of calling BUG() at runtime force a link error during compile
when a unsupported opcode is used with __cpacf_query() or
__cpacf_check_opcode() functions
- Fix a crash in ap_parse_bitmap_str() function on /sys/bus/ap/apmask
or /sys/bus/ap/aqmask sysfs file update with a relative mask value
- Fix "bindings complete" udev event which should be sent once all AP
devices have been bound to device drivers and again when unbind/bind
actions take place and all AP devices are bound again
- Facility list alt_stfle_fac_list is nowhere used in the decompressor,
therefore remove it there
- Remove custom kprobes insn slot allocator in favour of the standard
module_alloc() one, since kernel image and module areas are located
within 4GB
- Use kvcalloc() instead of kvmalloc_array() in zcrypt driver to avoid
calling memset() with a large byte count and get rid of the sparse
warning as result
* tag 's390-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/zcrypt: Use kvcalloc() instead of kvmalloc_array()
s390/kprobes: Remove custom insn slot allocator
s390/boot: Remove alt_stfle_fac_list from decompressor
s390/ap: Fix bind complete udev event sent after each AP bus scan
s390/ap: Fix crash in AP internal function modify_bitmap()
s390/cpacf: Make use of invalid opcode produce a link error
s390/cpacf: Split and rework cpacf query functions
s390/ipl: Introduce sysfs attribute 'scp_data' for dump ipl
s390/ipl: Introduce macros for (re)ipl sysfs attribute 'scp_data'
s390/ipl: Fix incorrect initialization of nvme dump block
s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
s390/ipl: Do not accept z/VM CP diag X'008' cmds longer than max length
s390/ipl: Fix size of vmcmd buffers for sending z/VM CP diag X'008' cmds
s390/alternatives: Convert runtime sanity check into compile time check
s390/iucv: Unexport iucv_root
tty: hvc-iucv: Make use of iucv_alloc_device()
s390/smsgiucv_app: Make use of iucv_alloc_device()
s390/netiucv: Make use of iucv_alloc_device()
s390/vmlogrdr: Make use of iucv_alloc_device()
s390/iucv: Provide iucv_alloc_device() / iucv_release_device()
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There is no user of iucv_root outside of the core IUCV code left.
Therefore remove the EXPORT_SYMBOL.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240506194454.1160315-7-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
| | | |_|/
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Provide iucv_alloc_device() and iucv_release_device() helper functions,
which can be used to deduplicate more or less identical IUCV device
allocation and release code in four different drivers.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240506194454.1160315-2-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
XSk infra's been using its own DMA sync shortcut to try avoiding
redundant function calls. Now that there is a generic one, remove
the custom implementation and rely on the generic helpers.
xsk_buff_dma_sync_for_cpu() doesn't need the second argument anymore,
remove it.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
We can save a couple more function calls in the Page Pool code if we
check for dma_need_sync() earlier, just when we test pp->p.dma_sync.
Move both these checks into an inline wrapper and call the PP wrapper
over the generic DMA sync function only when both are true.
You can't cache the result of dma_need_sync() in &page_pool, as it may
change anytime if an SWIOTLB buffer is allocated or mapped.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
