| Commit message (Collapse) | Author | Files | Lines |
|---|
|
Because it looks neater.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
R-Car V3H (R8A77980) SoC also has the R-Car gen3 compatible I2C controller,
so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add a module parameter to override SCL frequency provided by firmware.
This can be useful when testing spec compliance for I2C modes or when
debugging issues across multiple operating frequencies.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The I2C spec UM10204 Rev. 6 specifies the following timings.
Standard Fast Mode Fast Mode Plus
SCL low 4.7us 1.3us 0.5us
SCL high 4.0us 0.6us 0.26us
This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle
used for Standard-mode.
Add High Time Divider settings to correct duty cycle for FM(400kHz) and
FM+(1MHz).
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Previously the QUP driver limited operation mode to I2C Fast Mode. Add
Fast Mode Plus functionality by raising SCL limit from 400kHz to 1MHz.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for Qualcomm Centriq devices that are qup-v2 compatible but
do not support DMA, so nodma needs to be set.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In the for-loop test, ret will be either 0 or 1. So, the
comparison is pointless. Drop it, and drop the initializer
which is then also pointless.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Just use the value directly instead of assigning it to a
variable first. And then drop the unused variable.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Now %p doesn't print visible pointer address unless the user
really want it. According to Documentation/core-api/printk-formats.rst,
%px should be used instead, otherwise we could see:
rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
But I don't really understand why we need dump it in the first place!
Let's remove the whole pointless log.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since commit 1eace8344c02 ("i2c: add param sanity check to
i2c_transfer()") and b7f625840267 ("i2c: add quirk checks to core"), the
I2C core does this check now. We can remove it here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
Since commit 1eace8344c02 ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
For SMBus transactions the max permissible transfer size is
I2C_SMBUS_BLOCK_SIZE. It is possible that some clients might
not follow it strictly occasionally.
This would lead to stack corruption if the driver copies more than
I2C_SMBUS_BLOCK_SIZE bytes. Add a check to avoid such conditions.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The hardware does not handle updates to the length register gracefully
if the new value is less than the number of bytes received so far. If
this happens, the i2c controller will not stop the receive transaction
properly.
Fix this by ensuring that the updated length is ok. This is done by
making sure that the new length written to hardware is at least few
bytes more than the bytes received so far.
While at that refactor the length updation to a new function.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for SMBus alert mechanism to i2c-xlp9xx driver.
The second interrupt is parsed to use for SMBus alert.
The first interrupt is the i2c controller main interrupt.
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I3C busses have to know about all I2C devices connected on the I3C bus
to properly initialize the I3C master, and I2C frames can't be sent on
the bus until this initialization is done.
We can't let the I2C core parse the DT and instantiate I2C devices as
part of its i2c_add_adapter() procedure because, when done this way,
I2C devices are directly registered to the device-model and might be
attached to drivers which could in turn start sending frames on the bus,
which won't work since, as said above, the bus is not yet initialized.
Export of_i2c_register_device() in order to let the I3C core parse the
I2C device nodes by itself and initialize the bus.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently, of_i2c_register_devices() is responsible for retaining
info->of_node, but we're about to expose a function to parse I2C board
info without registering the I2C device.
We could possibly let this function retain ->of_node, but this approach
is prone to reference leak since people will have to remember to call
of_node_put() if something goes wrong between the OF node parsing and
the registration step.
Let's just retain the ->of_node in i2c_new_register() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There are no platform_data users anymore. Move the structs into the
driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
Some data structure members were either misspelled or missing.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Fixes: 380b8a85e7 ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
With CONFIG_PM, we get a harmless build warning:
drivers/i2c/busses/i2c-i801.c:1723:12: warning: ‘i801_resume’ defined but not used [-Wunused-function]
static int i801_resume(struct device *dev)
^~~~~~~~~~~
drivers/i2c/busses/i2c-i801.c:1714:12: warning: ‘i801_suspend’ defined but not used [-Wunused-function]
static int i801_suspend(struct device *dev)
^~~~~~~~~~~~
Follow design pattern from other drivers like i2c-brcmstb, i2c-mpc,
i2c-ocores, i2c-pnx, i2c-puv3, i2c-st, i2c-stu300 and i2c-mux-pca954x
and changing the ifdef CONFIG_PM to CONFIG_PM_SLEEP.
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Trivial fix to spelling mistakes in dev_dbg messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is a difference between attempts and retries.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In i2c_smbus_xfer_emulated(), the function i2c_transfer() is invoked to
transfer i2c messages. The number of actual transferred messages is
returned and saved to 'status'. If 'status' is negative, that means an
error occurred during the transfer process. In that case, the value of
'status' is an error code to indicate the reason of the transfer failure.
In most cases, i2c_transfer() can transfer 'num' messages with no error.
And so 'status' == 'num'. However, due to unexpected errors, it is probable
that only partial messages are transferred by i2c_transfer(). As a result,
'status' != 'num'. This special case is not checked after the invocation of
i2c_transfer() and can potentially lead to unexpected issues in the
following execution since it is expected that 'status' == 'num'.
This patch checks the return value of i2c_transfer() and returns an error
code -EIO if the number of actual transferred messages 'status' is not
equal to 'num'.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Move the code responsible for creating the dummy i2c clients used by
chips taking multiple slave addresses to a separate function.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
This allows us to drop two opencoded for loops. We also don't need to
check if the i2c client is NULL before calling i2c_unregister_device().
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
We now have a managed variant of nvmem_register(). Use it
in at24_probe().
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Peter Rosin <peda@axentia.se>
|
|
Commit feb2f19b1e8f ("eeprom: at24: move platform data processing into
a separate routine") introduced a bug where we incorrectly retireve the
at24_chip_data structure. Remove the unnecessary ampersand operator.
Fixes: feb2f19b1e8f ("eeprom: at24: move platform data processing into a separate routine")
Reported-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
The else branch cannot be taken as i will always equal num.
Get rid of the whole construct.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
exynos5_i2c_xfer contains lots of dead code, let's remove it and simplify
the rest. The patch should not introduce functional changes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Suggested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The only user of i2c_board_info->archdata is the OF parsing code and it
just pass a zero-initialized object which has the same effect as leaving
->archdata to NULL since the client object is allocated with kzalloc().
Get rid of this useless field.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Low-level controller enable function __i2c_dw_enable is overloaded to
also handle disabling. What's worse, even though the documentation
requires polling the IC_ENABLE_STATUS register when disabling, this
is not done: polling needs to be requested specifically by calling
__i2c_dw_enable_and_wait, which can also poll on enabling, but that
doesn't work if the IC_ENABLE_STATUS register is not implemented.
This is quite confusing if not in fact backwards.
Especially since the documentation says that disabling should be
followed by polling, the driver should be using a separate function
where it does one-shot disables to make the optimization stand out.
This refactors the two functions so that requested status is given
in the name rather than in a boolean argument. Specifically:
- __i2c_dw_enable: enable without polling (in accordance with docs)
- __i2c_dw_disable: disable and do poll (also as suggested by docs)
- __i2c_dw_disable_nowait: disable without polling (Linux-specific)
No functional change.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: fixed blank lines in header file]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 174a13aa8669 ("i2c: Add viperboard i2c master driver")
|
|
Returning -1 (-EPERM) is not appropriate here, go with -EIO.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7d6 ("i2c: New PMC MSP71xx TWI bus driver")
|
|
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7d6 ("i2c: New PMC MSP71xx TWI bus driver")
|
|
|
|
If DMA_ATTR_NO_WARN is passed to swiotlb_alloc_buffer(), it should be
passed further down to swiotlb_tbl_map_single(). Otherwise we escape
half of the warnings but still log the other half.
This is one of the multiple causes of spurious warnings reported at:
https://bugs.freedesktop.org/show_bug.cgi?id=104082
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 0176adb00406 ("swiotlb: refactor coherent buffer allocation")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # v4.16
|
|
after wake_affine()"
This reverts commit 7347fc87dfe6b7315e74310ee1243dc222c68086.
Srikar Dronamra pointed out that while the commit in question did show
a performance improvement on ppc64, it did so at the cost of disabling
active CPU migration by automatic NUMA balancing which was not the intent.
The issue was that a serious flaw in the logic failed to ever active balance
if SD_WAKE_AFFINE was disabled on scheduler domains. Even when it's enabled,
the logic is still bizarre and against the original intent.
Investigation showed that fixing the patch in either the way he suggested,
using the correct comparison for jiffies values or introducing a new
numa_migrate_deferred variable in task_struct all perform similarly to a
revert with a mix of gains and losses depending on the workload, machine
and socket count.
The original intent of the commit was to handle a problem whereby
wake_affine, idle balancing and automatic NUMA balancing disagree on the
appropriate placement for a task. This was particularly true for cases where
a single task was a massive waker of tasks but where wake_wide logic did
not apply. This was particularly noticeable when a futex (a barrier) woke
all worker threads and tried pulling the wakees to the waker nodes. In that
specific case, it could be handled by tuning MPI or openMP appropriately,
but the behavior is not illogical and was worth attempting to fix. However,
the approach was wrong. Given that we're at rc4 and a fix is not obvious,
it's better to play safe, revert this commit and retry later.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: efault@gmx.de
Cc: ggherdovich@suse.cz
Cc: hpa@zytor.com
Cc: matt@codeblueprint.co.uk
Cc: mpe@ellerman.id.au
Link: http://lkml.kernel.org/r/20180509163115.6fnnyeg4vdm2ct4v@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit c1adf20052d8 ("Introduce rb_replace_node_rcu()")
rbtree_augmented.h uses RCU related data structures but does not include
the header file. It works as long as it gets somehow included before
that and fails otherwise.
Link: http://lkml.kernel.org/r/20180504103159.19938-1-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When addr2line output contains discriminator, the current awk script
cannot parse it. This patch fixes it by extracting key words using
regex which is more reliable.
$ scripts/faddr2line vmlinux tlb_flush_mmu_free+0x26
tlb_flush_mmu_free+0x26/0x50:
tlb_flush_mmu_free at mm/memory.c:258 (discriminator 3)
scripts/faddr2line: eval: line 173: unexpected EOF while looking for matching `)'
Link: http://lkml.kernel.org/r/1525323379-25193-1-git-send-email-changbin.du@intel.com
Fixes: 6870c0165feaa5 ("scripts/faddr2line: show the code context")
Signed-off-by: Changbin Du <changbin.du@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While reflinking an inode, we create a new inode in orphan directory,
then take EX lock on it, reflink the original inode to orphan inode and
release EX lock. Once the lock is released another node could request
it in EX mode from ocfs2_recover_orphans() which causes downconvert of
the lock, on this node, to NL mode.
Later we attempt to initialize security acl for the orphan inode and
move it to the reflink destination. However, while doing this we dont
take EX lock on the inode. This could potentially cause problems
because we could be starting transaction, accessing journal and
modifying metadata of the inode while holding NL lock and with another
node holding EX lock on the inode.
Fix this by taking orphan inode cluster lock in EX mode before
initializing security and moving orphan inode to reflink destination.
Use the __tracker variant while taking inode lock to avoid recursive
locking in the ocfs2_init_security_and_acl() call chain.
Link: http://lkml.kernel.org/r/1523475107-7639-1-git-send-email-ashish.samant@oracle.com
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since exit_mmap() is done without the protection of mm->mmap_sem, it is
possible for the oom reaper to concurrently operate on an mm until
MMF_OOM_SKIP is set.
This allows munlock_vma_pages_all() to concurrently run while the oom
reaper is operating on a vma. Since munlock_vma_pages_range() depends
on clearing VM_LOCKED from vm_flags before actually doing the munlock to
determine if any other vmas are locking the same memory, the check for
VM_LOCKED in the oom reaper is racy.
This is especially noticeable on architectures such as powerpc where
clearing a huge pmd requires serialize_against_pte_lookup(). If the pmd
is zapped by the oom reaper during follow_page_mask() after the check
for pmd_none() is bypassed, this ends up deferencing a NULL ptl or a
kernel oops.
Fix this by manually freeing all possible memory from the mm before
doing the munlock and then setting MMF_OOM_SKIP. The oom reaper can not
run on the mm anymore so the munlock is safe to do in exit_mmap(). It
also matches the logic that the oom reaper currently uses for
determining when to set MMF_OOM_SKIP itself, so there's no new risk of
excessive oom killing.
This issue fixes CVE-2018-1000200.
Link: http://lkml.kernel.org/r/alpine.DEB.2.21.1804241526320.238665@chino.kir.corp.google.com
Fixes: 212925802454 ("mm: oom: let oom_reap_task and exit_mmap run concurrently")
Signed-off-by: David Rientjes <rientjes@google.com>
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
radix_tree_replace_slot() is called twice for head page, it's obviously
a bug. Let's fix it.
Link: http://lkml.kernel.org/r/20180423072101.GA12157@hori1.linux.bs1.fc.nec.co.jp
Fixes: e71769ae5260 ("mm: enable thp migration for shmem thp")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Zi Yan <zi.yan@sent.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The existing kcore code checks for bad addresses against __va(0) with
the assumption that this is the lowest address on the system. This may
not hold true on some systems (e.g. arm64) and produce overflows and
crashes. Switch to using other functions to validate the address range.
It's currently only seen on arm64 and it's not clear if anyone wants to
use that particular combination on a stable release. So this is not
urgent for stable.
Link: http://lkml.kernel.org/r/20180501201143.15121-1-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Tested-by: Dave Anderson <anderson@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>a
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
