| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit "b5b4a41b392960010fccf1f9ccf8334d612bd450" was dereferencing
chip after it has been freed. This patch fixes that and at the same
time removes some debugging messages, which are unnecessary, as they
are just printing information about entry and exit from a function,
and which switch-case it is executing.
we can easily get from ftrace the information about the entry and exit
from a function.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
| |
removed all references of snd_printk with the standard dev_* macro.
[a few places degraded to dev_dbg(), too -- tiwai]
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Move the controls init code outside the init_hw() function because is must
not be called during resume.
This patch moves the code that initializes the card's controls with
default valued from the init_hw() function into a separated
set_mixer_defaults() function (one for each of the 16 supported
cards). This change is necessary because during resume we must
resurrect the hardware without losing the previous
settings. set_mixer_defaults() must be called only once when the
module is loaded.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Changes the way the firmware is passed through functions.
When CONFIG_PM is enabled the firmware cannot be released because the
driver will need it again to resume the card.
With this patch the firmware is passed as an index of the struct
firmware card_fw[] in place of a pointer. That same index is then used
to locate the firmware in the firmware cache.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
| |
With this patch the drivers do not set the vmixer volume anymore at startup
because it is actually the output volume of the voices and ALSA mandates
that the volume must be 0 by default.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
| |
Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
From: Giuliano Pochini <pochini@shiny.it>Add echoaudio sound drivers (darla20, darla24, echo3g, gina20, gina24,
indigo, indigodj, indigoio, layla20, lala24, mia, mona)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
