| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.
The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.
Fixes: 9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As mentioned slightly out of patch context in the code, there
is no reset routine for the chip. On boards where the chip is
supplied by a fixed regulator, it might not even be resetted
during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe
routine will generate a loud pop sound when ANA_POWER is
being programmed. Avoid this by properly disabling just the
VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Fabio Estevam <festivem@gmail.com>
Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
SGTL5000_SMALL_POP is a bit mask, not a value. Usage of
correct definition makes device probing code more clear.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20190719100524.23300-4-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
| |
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
| |
Enable 5-band graphic equalizer which allows manipulation of
gain in range -11.75dB to 12dB for 5 specific sound bands:
115Hz, 330Hz, 990Hz, 3000Hz, 9900Hz.
Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
To handle the soft reboot case, the internal PLL must be
disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits
SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in
register SGTL5000_CHIP_ANA_POWER.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.
In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK
And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, below code actually does not update any bit because
SGTL5000_SMALL_POP is 0.
snd_soc_update_bits(codec, SGTL5000_CHIP_REF_CTRL, SGTL5000_SMALL_POP, 1);
The SGTL5000_SMALL_POP should be BIT(0) rather than 0, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
| |
|
|
|
|
|
|
|
|
| |
SGTL5000_PLL_FRAC_DIV_MASK is used to mask bits 0-10 (11 bits in total) of
register CHIP_PLL_CTRL, so fix the mask to accomodate all this bit range.
Reported-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
| |
|
|
|
|
|
|
| |
The list below the comment relates to sgtl5000 registers addresses, so change
the comment to improve the description.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
According to the datasheet:
CHIP_MIC_CTRL 0x002A
BITS[9:8] BIAS_RESISTOR
0x0 = Powerd off
0x1 = 2.0 kohm
0x2 = 4.0 kohm
0x3 = 8.0 kohm
Thus SGTL5000_BIAS_R_MASK should be defined as 0x0300 instead of 0x0200.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |
|
|
|
|
|
|
|
| |
Remove unnecessary headers:
- mach/hardware.h in sgtl5000.c
- linux/i2c.h in sgtl5000.h
Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
Add Freescale SGTL5000 codec support.
Supported features:
- line-in and mic input
- headphone and line-out output
- line-in bypass ADC and DAC to headphone
- 16, 20, 24, 32 bit audio
- 8 ~ 96k sample rates
Signed-off-by: Zeng Zhaoming <zhaoming.zeng@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
