| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
Make the code easier to read by using snd_soc_update_bits() over
read/modify/write sequences. Also use separate per-register
variables instead of re-using "data". This can prevent accidental
over-writing and makes it clear for which register each bit value is
intended.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
| |
Inter-register definitions should use BIT and GENMASK definitions
and also be grouped by what register they belong to. This makes it
easy to cross-check with the datasheet and is consistent with other
drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
| |
Drop definition of frequencies that only map from one number to
the same number. This is not needed and if misused can hide
bugs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
| |
All register definitions should use the AIC32X4_REG macro, even the ones
in page 0. This makes datasheet lookup more consistent and helps with
alignment both in this file and across other tlv320aic* drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add the ability to configure the MFP1->MFP5 registers
as GPIOs. In addition adding ALSA controls to get and set
the GPIO state.
Per the data sheet each MFP can be configured as a GPIO
input only, output only or either an input or output.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
| |
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the Negative Terminal Input Routing Configuration is only set
when there is a special routing configuration. If we don't use one of
the inputs IN1 or IN2 as negative terminal input, the PGA and recording
does not work.
This patch adds a route from CM1L/CM1R to the PGA as negative input by
default. With this configuration the PGA can amplify all input signals
and line-in/mic works again.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Playback of a mono stream should output the same stream on both
channels. At the moment only the left analog signal is valid, the right
one is just noise.
This patch maps the left digital channel onto both DACs when receiving a
mono stream.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In its previous status, the first capture didn't work properly;
nothing was actually recorded from the microphone. This
behaviour was observed using a Visstrim M10 board.
In order to solve this BUG a workaround has been added that,
during the initialization process of the codec, powers on and
off the ADC.
The issue seems related to a HW BUG or some behavior that
is not documented in the datasheet.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
