| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ux500 platform hasn't used board files for a long time, and
nothing defines a ab8500_codec_platform_data, so we can just
remove the probing based on that and always use device tree
properties directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | | |
| | \ | |
| |\ \ \
| | | |
| | | |
| | | | |
into asoc-next
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
I just added an I2C dependency to the wm8985 driver to work around
a build failure, but it turns out that was premature: we actually
need to depend on SND_SOC_I2C_AND_SPI, as the driver can work with either
of the two, and we only need to prevent a configuration that has
I2C=m and SND_SOC_WM8985=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 05252513fbb9 ("ASoC: wm8985: add i2c dependency")
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The wm8985 driver is now user-selectable, but building it with
I2C disabled results in a link failure:
sound/built-in.o: In function `wm8985_i2c_probe':
:(.text+0x44914): undefined reference to `__devm_regmap_init_i2c'
sound/built-in.o: In function `wm8985_exit':
:(.exit.text+0x3d8): undefined reference to `i2c_del_driver'
sound/built-in.o: In function `wm8985_modinit':
:(.init.text+0x1454): undefined reference to `i2c_register_driver'
This adds a Kconfig dependency the way that the other codec
drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 811e66de2241 ("ASoC: wm8985: add support for WM8758")
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the WM8758 support into the
WM8985 driver.
The chip selection is done by the I2C name. The SPI probe supports only
the WM8985.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the register definitions
for WM8758 specific bit fields to the header file.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Use SND_SOC_NOPM constant, instead of -1.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Drop redundant include of moduleparam.h
The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@
@ depends on includesmodule @
@@
- #include <linux/moduleparam.h>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| |\ \ \ \ \ \ \
| | | | | |/ /
| | | | |/| |
| | | | | | | |
'asoc/topic/tlv320aic31xx', 'asoc/topic/tpa6130a2', 'asoc/topic/twl6040' and 'asoc/topic/wm8731' into asoc-next
|
| | | | | |/ /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This patch adds 32 bit word capability to the wm8731 driver. The wm8731
codec is capable of handling 32 bit word sizes, however that has not
previously been activated in the codec driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Replace goto err_gpio by return ret
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add DAPM support and updated rx51 accordingly.
As a consequence:
- the exported function tpa6130a2_stereo_enable is not needed anymore
- the mutex is dealt in the DAPM
- the power state is tracked by the DAPM
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use snd_soc_{info,get,put}_volsw instead of custom volume functions
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use regmap instead of open-coding IO access and caching
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
[On N900]
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |/ /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add tpa6130a2 controls by the component API and update rx51 accordingly
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[koike: port for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |/
| | |/|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The datasheet uses decimal numbers for the register addresses, convert the
register values from hexadecimal to decimal and introduce macro for the
register definitions. This way it is easier to look up registers in the
documentation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add channel 1 and 2 input mixer registers and the related ALSA mixer
controls for TAS5717/19 chips.
The mixer control coefficients on the chip are linear in the range
-3.99999 to +3.99999, encoded in 3.23 number format.
In this patch the mixer controls are limited to 128 values
from 0.0 to 1.0 in 1/64 steps.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
TAS571x features multiple biquad filters. Their coefficients
are stored in 20-byte registers, which cannot be supported by
regmap.
This patch adds read and write functions for multi-word (32-bit) register
access and mixer controls for the biquads. The multi-word read/write
functions can be used in the future to implement other features like DRC or
output mixer.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | | |
Add biquad register definitions for TAS5717/19.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | \ \ | |
| |\ \ \ \
| | |/ /
| |/| |
| | | | |
'asoc/topic/sti' and 'asoc/topic/sunxi' into asoc-next
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This controls the volume for the line out pins of SGTL5000.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Disabling the SGTL5000 through regulators would certainly save more
power than simply disabling the reference voltages as described in the
data sheet, but won't properly restore things on resume.
This driver does not support active regulators. So we simply disable the
reference bias currents.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
To handle the soft reboot case, the internal PLL must be
disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits
SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in
register SGTL5000_CHIP_ANA_POWER.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.
In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK
And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
If an error occurs writing defaults, produce an error message but
continue writing other registers. The failure of a single write should
not cause catastrophic device failure.
In at least one occurrence, I2C writes of CHIP_ANA_POWER were nacked,
though continuing allowed the device to operate properly.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Regulator support on SGTL5000 is broken because the VDDIO and
VDDA and VDDD should be powered on before enabling MCLK as
shown in Figure 4 of [1]. This requires moving control of the
regulators from the codec block to the I2C block of the driver.
The bulk of this patch consists of swapping the codec device with
the i2c client. The new field num_supplies in struct sgtl5000_priv
is used instead of ARRAY_SIZE(supplies) to handle the special case
when the internal LDO is used instead of external VDDD.
Note that ER1 in the SGTL5000 Errata document [2] suggests that
all designs should use external VDDD.
Since the internal LDO can only be enabled after I2C is available,
there's no benefit in treating it as a regulator, so this patch
removes the regulator structure surrounding it.
Instead, a single block of code in sgtl5000_i2c_probe() performs
the initialization sequence in section 2.2.1.1 of [3] and page
26 of [1].
References:
[1] SGTL5000 data sheet
http://cache.nxp.com/files/analog/doc/data_sheet/SGTL5000.pdf
[2] SGTL5000 errata
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
[3] SGTL5000 Initialization and programming app note
http://cache.nxp.com/files/analog/doc/app_note/AN3663.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
All new designs should use external VDDD according to official
documentation. See ER1 in errata sheet:
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| |\ \ \ \| |
| | | | | |
| | | | | |
| | | | | | |
'asoc/topic/rt5670' and 'asoc/topic/s8' into asoc-next
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
reg-8a assign the tracking source for each ASRC tracker. The default
value is 0x0000 which means all ASRC trackers will track LRCK1. But
in most case, we wish each ASRC tracker track the corresponding LRCK.
i.e. ASRC1 tracks LRCK1, ASRC2 tracks LRCK2 and so on. So, we rewrite
reg-8a as 0x0123.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | |/ /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The register setting for HP Playback Volume is inverted. So, set
the invert flag in SOC_DOUBLE_TLV.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use devm_* API to simplify the code.
This patch also fixes the return value in probe error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The patch fixes the issue that variable dereferenced before checking
'rt5514_dsp->substream'. Move the assignment to after the variable
checking of 'rt5514_dsp->substream'.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | |/ /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The device has multiple control interfaces, I2C and SPI. The I2C interface
mainly controls the register settings of codec. The SPI interface is in
order to provide the high speed transmission of data. For example, high
bandwidth memory read/write of DSP. The patch adds the rt5514 SPI driver
for loading the firmware of DSP and retrieving the voice data from DSP
after the system is waked up by specific voice.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | | |
The patch adds the control of MCLK that depends on the status of DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| | \ \ | |
| |\ \ \ \ \ \ \
| | | | | |/ /
| | | | |/| |
| | | | | | | |
'asoc/topic/max9877', 'asoc/topic/mtk' and 'asoc/topic/nau8825' into asoc-next
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Thanks Mark and Anatol for the discussion. According to the result,
the standard C will translate any non-zero value into true, or
false otherwise.
QUOTE:
"6.3.1.2 Boolean type
When any scalar value is converted to _Bool, the result is 0 if the
value compares equal to 0; otherwise, the result is 1
"
Thus, the "!!" idiom is removed.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The original design only covers the jack insertion logic is active low.
Add more condition to cover no matter the logic is active low and high.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The newly added nau8825_dai_is_active() function is only called from
the PM logic that is build-time conditional in this driver, so we get
a warning when CONFIG_PM is disabled:
sound/soc/codecs/nau8825.c:229:13: error: 'nau8825_dai_is_active' defined but not used [-Werror=unused-function]
static bool nau8825_dai_is_active(struct nau8825 *nau8825)
By replacing the #ifdef around the functions with a __maybe_unused
annotation, the code becomes more robust to this kind of problem
and we no longer get the warning while also slightly improving
readability.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b50455fab459 ("ASoC: nau8825: cross talk suppression measurement function")
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The cross talk measurement function can reduce cross talk across the JKTIP
HPL) and JKR1(HPR) outputs which measures the cross talk signal level to
determine what is the cross talk reduction gain. This system works by
sending a 23Hz -24dBV sine wave into the headset output DAC and through
the PGA. The output of the PGA is then connected to an internal current
sense which measures the attenuated 23Hz signal and passing the output to
an ADC which converts the measurement to a binary code. With two separated
measurement, one for JKR1(HPR) and the other JKTIP(HPL), measurement data
can be separated read in IMM_RMS_L for HSR and HSL after each measurement.
Thus, the measurement function has four states to complete whole sequence.
(1)Prepare state : Prepare the resource for detection and transfer to HPR
IMM stat to make JKR1(HPR) impedance measure.
(2)HPR IMM state : Read out orignal signal level of JKR1(HPR) and transfer
to HPL IMM state to make JKTIP(HPL) impedance measure.
(3)HPL IMM state : Read out cross talk signal level of JKTIP(HPL) and
transfer to IMM state to determine suppression sidetone gain.
(4)IMM state : Computes cross talk suppression sidetone gain with orignal
and cross talk signal level. Apply this gain and then restore codec con-
figuration. Then transfer to Done state for ending.
In order to get the cross talk suppression sidetone gain, we need the
function to compute log10 value and the result is round off to 3 decimal.
This function takes reference to dvb-math. The source code locates as the
following. "Linux/drivers/media/dvb-core/dvb_math.c"
Then, the orignal and cross talk signal vlues need to be characterized.
The sidetone value can be converted to decibel with the equation below.
sidetone = 20 * log (original signal level / crosstalk signal level)
Besides, the state machine for cross talk process needs interruptions to
trigger worked. We have the RMS intrruption enabled with the internal VCO
clock when headset connected. In the interrupt handler, the driver will
judge the headset is high impedance or not. If yes, the cross talk supp-
ression shouldn't apply and do nothing but relieve the protection raised
before. Otherwise, apply the cross talk suppression in the headset and
start the process.
Because the process spends a lot of time, there is an resource race issue
easily between the application and interruption. They will control codec
power and clock concurrently. In one situaiton, the jack is inserted when
playback, and then the application changes to headset device. The applica-
tion prepares the playback and interrupt handler raises work for cross
talk process together. For this case, the solution is that driver delays
soc jack report until cross talk process completes. The mechanism can
avoid application to do playback preparation before cross talk detection
is still working.
In another situaiton, the system suspends when playback. After resume, the
system restarts playback, and meanwhile jack detection restarts. The play-
back preparation and cross talk process triggered by interruptions happens
concurrently. For the case, the driver provides the semaphone to syn-
chronize the playback and interrupt handler. In order to avoid the play-
back interfered by cross talk process, the driver make the playback prepa-
ration halted until cross talk process finish. After codec resume, the
driver finds the codec dai is active, and then the driver raises the pro-
tection for cross talk function to avoid the playback recovers before
cross talk process finish.
The driver also provides cancel method to forcely cancel the cross talk
task and restores the configuration to original status. Before the codec
remove, ejection, or suspend, the driver is obliged to cancel the cross
talk detection process. It can reduce the risk of failure when quickly and
continually doing jack insertion and ejection.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
There is typo in the name of biquad filter coefficients control.
The patch is to fix the typo.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The driver changes jack type detection interruption to non-clock archi-
tecture for less 1mW power saving. The architecture is called manual mode
jack detection. It has no hardware debounce, no jack type detection, but
only detecting jack insertion. After jack insertion, the driver will
switch to auto mode jack detection with internal clock which can detect
microphone, jack type and do hardware debounce.
The manual architecture has these main changes including codec initiation,
interruption, clock control, and power management. When codec initiation
or system resume, the clock is closed as jack insertion detection at man-
ual mode, and bypass debounce circuit. These configurations move to resume
setup function when setup bias level after resume.
When jack insertion detection happens, the manual mode turns off and make
configuration about jack type detection interruption at auto mode in auto
irq setup function which can detect microphone and jack type. The inter-
ruption will switch to manual mode again with clock free until jack ejec-
tion happens.
The system clock configuration adds clock disable option which can disable
internal VCO clock. Before the system clock change, there is an restric-
tion added to make sure clock disabled and not config any clock when no
headset connected.
In power management, we involve the solution about races and jack detec-
tion in resume from Ben Zhang in the following patch and list his comment.
[PATCH] ASoC: nau8825: Fix jack detection across suspend
"Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power."
"Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly."
Change SAR widget to supply type which can prevent the codec keeping at
SND_SOC_BIAS_ON during suspend. The codec suspend function can just invoke
normally.
Before the system suspends, the driver turns off all interruptions. Keep
the interruption quiet before resume setup completes. The ADC channel will
be disabled which is needed for interruptions at audo mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add programmable biquad filter configuration control for user space.
The filter is configurable for low pass filters, high pass filters,
Notch filter, etc in the ADC and DAC path.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The I2C driver has an i2c_device_id array but that information isn't
exported to the module using the MODULE_DEVICE_TABLE() macro. So the
module autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the module.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The default value of DAC channel select is reverse in codec.
For normal usage, switch the channel select when codec bootup.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The interrupt clock is gated by x1[10:8], one of them needs to be enabled
all the time for interrupts to happen. We change codec to enable ADC
because it's helpful to reduce playback pop noise.
Don't use force enable pin to enable ADC instead of ADC widget event.
That won't interfere DAPM operation and let bias work normally.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Decrease internal clock frequency for power saving when standby.
But clock divider needs restore when MCLK as system clock in playback.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In FLL calculation, increase VCO/DCO frequency for better performance.
Besides, have different register configuration according to fraction or not
when apply FLL parameters.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
| | | | | |/ /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Extend FLL clock source selection. The source can be from MCLK, BCLK or FS.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
