| Commit message (Collapse) | Author | Files | Lines |
|---|
|
The trans_tre_max field of the IPA endpoint structure is only used
to limit the number of fragments allowed for an SKB being prepared
for transmission. Recognizing that, rename the field skb_frag_max,
and reduce its value by 1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each GSI channel has a TLV FIFO of a certain size, specified in the
configuration data for an AP channel. That size dictates the
maximum number of TREs that are allowed in a single transaction.
The only way that value is used after initialization is as a limit
on the number of TREs in a transaction; calling it "tlv_count"
isn't helpful, and in fact gsi_channel_trans_tre_max() exists to
sort of abstract it.
Instead, rename the channel->tlv_count field trans_tre_max, and get
rid of the helper function. Update a couple of comments as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 8797972afff3d ("net: ipa: remove command info pool"), the
maximum number of IPA commands that would be sent in a single
transaction was defined. That number can't exceed the size of the
TLV FIFO on the command channel, and we can check that at runtime.
To add this check, pass a new flag to gsi_channel_data_valid() to
indicate the channel being checked is being used for IPA commands.
Knowing that we can also verify the channel direction is correct.
Use a new local variable that refers to the command-specific portion
of the data being checked.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the traffic class field is ignored while firmware has
already supported to pedit flowinfo fields, including traffic
class and flow label, now add it back.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Link: https://lore.kernel.org/r/20220609080136.151830-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit a14857c27a50 ("rtnetlink: verify rate parameters for calls to
ndo_set_vf_rate") has been merged to master, so we can to remove the
now-duplicate checks in drivers.
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220609084717.155154-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These two helpers are only used from core networking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, tcp_memory_allocated can hit tcp_mem[] limits quite fast.
Each TCP socket can forward allocate up to 2 MB of memory, even after
flow became less active.
10,000 sockets can have reserved 20 GB of memory,
and we have no shrinker in place to reclaim that.
Instead of trying to reclaim the extra allocations in some places,
just keep sk->sk_forward_alloc values as small as possible.
This should not impact performance too much now we have per-cpu
reserves: Changes to tcp_memory_allocated should not be too frequent.
For sockets not using SO_RESERVE_MEM:
- idle sockets (no packets in tx/rx queues) have zero forward alloc.
- non idle sockets have a forward alloc smaller than one page.
Note:
- Removal of SK_RECLAIM_CHUNK and SK_RECLAIM_THRESHOLD
is left to MPTCP maintainers as a follow up.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If sk->sk_forward_alloc is 150000, and we need to schedule 150001 bytes,
we want to allocate 1 byte more (rounded up to one page),
instead of 150001 :/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We plan keeping sk->sk_forward_alloc as small as possible
in future patches.
This means we are going to call sk_memory_allocated_add()
and sk_memory_allocated_sub() more often.
Implement a per-cpu cache of +1/-1 MB, to reduce number
of changes to sk->sk_prot->memory_allocated, which
would otherwise be cause of false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Each protocol having a ->memory_allocated pointer gets a corresponding
per-cpu reserve, that following patches will use.
Instead of having reserved bytes per socket,
we want to have per-cpu reserves.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to memcg interface, SK_MEM_QUANTUM is effectively PAGE_SIZE.
This might change in the future, but it seems better to avoid the
confusion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit bd68a2a854ad5a85f0c8d0a9c8048ca3f6391efb.
This change broke memcg on arches with PAGE_SIZE != 4096
Later, commit 2bb2f5fb21b04 ("net: add new socket option SO_RESERVE_MEM")
also assumed PAGE_SIZE==SK_MEM_QUANTUM
Following patches in the series will greatly reduce the over allocations
problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's a rule in certs/Makefile for which the command begins with eight
spaces. This results in:
../certs/Makefile:21: FORCE prerequisite is missing
../certs/Makefile:21: *** missing separator. Stop.
Fix this by turning the spaces into a tab.
Fixes: addf466389d9 ("certs: Check that builtin blacklist hashes are valid")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Mickaël Salaün <mic@linux.microsoft.com>
cc: keyrings@vger.kernel.org
Link: https://lore.kernel.org/r/486b1b80-9932-aab6-138d-434c541c934a@digikod.net/ # v1
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As Liviu pointed out, the arm,malidp-arqos-high-level property
mentioned in the original .txt binding was a mistake, and
arm,malidp-arqos-value needs to take its place.
The binding commit ce6eb0253cba ("dt/bindings: display: Add optional
property node define for Mali DP500") mentions the right name in the
commit message, but has the wrong name in the diff.
Commit d298e6a27a81 ("drm/arm/mali-dp: Add display QoS interface
configuration for Mali DP500") uses the property in the driver, but uses
the shorter name.
Remove the wrong property from the binding, and use the proper name in
the example. The actual property was already documented properly.
Fixes: 2c8b082a3ab1 ("dt-bindings: display: convert Arm Mali-DP to DT schema")
Link: https://lore.kernel.org/linux-arm-kernel/YnumGEilUblhBx8E@e110455-lin.cambridge.arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220609162729.1441760-1-andre.przywara@arm.com
|
|
There's no reason to list the same value twice in an 'enum'. This was fixed
treewide in commit c3b006819426 ("dt-bindings: Fix 'enum' lists with
duplicate entries"), but this one got added in the merge window.
A meta-schema change will catch future cases.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220606212239.1360877-1-robh@kernel.org
|
|
This function is only called from assembly, no need for a prototype
declaration in a header file. In addition, add #ifdef around the
function since it is only used when CONFIG_KASAN_HW_TAGS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
|
|
The EFI save/restore code is confused. When saving the check for saving
FFR is inverted due to confusion with the streaming mode check, and when
restoring we check if we need to restore FFR by checking the percpu
efi_sm_state without the required wrapper rather than based on the
combination of FA64 support and streaming mode.
Fixes: e0838f6373e5 ("arm64/sme: Save and restore streaming mode over EFI runtime calls")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220602124132.3528951-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
While here it may be no difference, the kcalloc() has some checks
against overflow and it's logically correct to call it for an array.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cleaning up driver data is actually already handled by driver core,
so there is no need to do it manually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since platform_device_unregister() is NULL-aware, we don't need to duplicate
this check. Remove it and fold the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently we are using BIT(), but GENMASK(). Make use of the latter one
as well (far less error-prone, far more concise).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete the redundant word 'in'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20220610070543.59338-1-wangxiang@cdjrlc.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In the awk script, there was a typo with the comparison operator when
checking if the matched pattern is inside an Enum block.
This prevented the generation of the whole sysreg-defs.h header.
Fixes: 66847e0618d7 ("arm64: Add sysreg header generation scripting")
Signed-off-by: Alejandro Tafalla <atafalla@dnyon.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220609204220.12112-1-atafalla@dnyon.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove().
Signed-off-by: Ke Liu <liuke94@huawei.com>
Link: https://lore.kernel.org/r/20220528093140.1573816-1-liuke94@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's some pretty close code here, with the exception
of RCU dereference vs. protected dereference. Refactor
this to just return a pointer and then do the deref in
the caller later.
Change-Id: Ide5315e2792da6ac66eaf852293306a3ac71ced9
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-77-Julia.Lawall@inria.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-8-Julia.Lawall@inria.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add an new state, RTW89_PHY_DCFO_STATE_HOLD, to keep CFO acceleration
after CFO_PERIOD_CNT if the traffic is UL-OFDMA, which is calculated
based on RX trigger frame counter.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-4-pkshih@realtek.com
|
|
Adding this allows us to maintain trigger frame statistics, which is
required for our CFO tracking decisions.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-3-pkshih@realtek.com
|
|
Define trigger stype of control frame, and its checking function, struct
and trigger type within common_info of trigger.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-2-pkshih@realtek.com
|
|
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220606014237.290466-1-chi.minghao@zte.com.cn
|
|
Setting RLB_NULL_INDEX is not needed as this is done in bond_alb_initialize
which is called by bond_open.
Also reduce the number of rtnl_unlock calls by just using the standard
goto cleanup path.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reporting errors via extack in both bond_newlink
and bond_changelink.
Instead of having to look in the kernel log for why an option was not
correct just report the error to the user via the extack variable.
What is currently reported today:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
RTNETLINK answers: Device or resource busy
After this change:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
Error: unable to set option because the bond is up.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif
reset for port devices") adds a new entry (flowi_l3mdev) in the common
flow struct used for indicating the l3mdev index for later rule and
table matching.
The l3mdev_update_flow() has been adapted to properly set the
flowi_l3mdev based on the flowi_oif/flowi_iif. In fact, when a valid
flowi_iif is supplied to the l3mdev_update_flow(), this function can
update the flowi_l3mdev entry only if it has not yet been set (i.e., the
flowi_l3mdev entry is equal to 0).
The SRv6 End.DT6 behavior in VRF mode leverages a VRF device in order to
force the routing lookup into the associated routing table. This routing
operation is performed by seg6_lookup_any_nextop() preparing a flowi6
data structure used by ip6_route_input_lookup() which, in turn,
(indirectly) invokes l3mdev_update_flow().
However, seg6_lookup_any_nexthop() does not initialize the new
flowi_l3mdev entry which is filled with random garbage data. This
prevents l3mdev_update_flow() from properly updating the flowi_l3mdev
with the VRF index, and thus SRv6 End.DT6 (VRF mode)/DT46 behaviors are
broken.
This patch correctly initializes the flowi6 instance allocated and used
by seg6_lookup_any_nexhtop(). Specifically, the entire flowi6 instance
is wiped out: in case new entries are added to flowi/flowi6 (as happened
with the flowi_l3mdev entry), we should no longer have incorrectly
initialized values. As a result of this operation, the value of
flowi_l3mdev is also set to 0.
The proposed fix can be tested easily. Starting from the commit
referenced in the Fixes, selftests [1],[2] indicate that the SRv6
End.DT6 (VRF mode)/DT46 behaviors no longer work correctly. By applying
this patch, those behaviors are back to work properly again.
[1] - tools/testing/selftests/net/srv6_end_dt46_l3vpn_test.sh
[2] - tools/testing/selftests/net/srv6_end_dt6_l3vpn_test.sh
Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices")
Reported-by: Anton Makarov <am@3a-alliance.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220608091917.20345-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Swap around the GRE and VLAN parts in the flow-key offloaded by
the driver to fit in with other tunnel types and the firmware.
Without this change used cases with GRE+VLAN on the outer header
does not get offloaded as the flow-key mismatches what the
firmware expect.
Fixes: 0d630f58989a ("nfp: flower: add support to offload QinQ match")
Fixes: 5a2b93041646 ("nfp: flower-ct: compile match sections of flow_payload")
Signed-off-by: Etienne van der Linde <etienne.vanderlinde@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nfp_net_sriov_check is added in nfp_app_get_vf_config which intends
to ensure ivi->vlan_proto and ivi->max_tx_rate/min_tx_rate can be
read from VF config table only when firmware supports corresponding
capability.
However, "nfp_app_get_vf_config" can be called by commands like
"ip a", "ip link set $DEV up" and "ip link set $DEV vf $NUM vlan
$param" (with VF). When using commands above, many warnings
"ndo_set_vf_<cap_x> not supported" would appear if firmware doesn't
support VF rate limit and 802.1ad VLAN assingment. If more VFs are
created, things could get worse.
Thus, this patch add an extra bool parameter for nfp_net_sriov_check
to enable/disable the cap check warning report. Unnecessary warnings
in nfp_app_get_vf_config can be avoided. Valid warnings in kinds of
vf setting function can be reserved.
Fixes: e0d0e1fdf1ed ("nfp: VF rate limit support")
Fixes: 59359597b010 ("nfp: support 802.1ad VLAN assingment to VF")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a follow up of commit 3226b158e67c
("net: avoid 32 x truesize under-estimation for tiny skbs")
When/if we increase MAX_SKB_FRAGS, we better make sure
the old bug will not come back.
Adding a check in napi_get_frags() would be costly,
even if using DEBUG_NET_WARN_ON_ONCE().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 6454eca81eae ("net: Use lockdep_assert_in_softirq()
in napi_consume_skb()") added a check in napi_consume_skb()
which is a bit weak.
napi_consume_skb() and __napi_alloc_skb() should only
be used from BH context, not from hard irq or nmi context,
otherwise we could have races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove this check from fast path unless CONFIG_DEBUG_NET=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace four WARN_ON() that have not triggered recently
with DEBUG_NET_WARN_ON_ONCE().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sk_stream_kill_queues() has three checks which have been
useful to detect kernel bugs in the past.
However they are potentially a problem because they
could flood the syslog.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet_sock_destruct() has four warnings which have been
useful to point to kernel bugs in the past.
However they are potentially a problem because they
could flood the syslog.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One check in dev_loopback_xmit() has not caught issues
in the past.
Keep it for CONFIG_DEBUG_NET=y builds only.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Check against skb dst in socket backlog has never triggered
in past years.
Keep the check omly for CONFIG_DEBUG_NET=y builds.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a convenient helper, let's use it.
This will make the following patch easier to review and smaller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
