From 339e834fe06a2367ab8dcc18e57e810997ac9750 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 7 Oct 2013 17:12:24 +0200 Subject: ARM: dts: omap3-igep0020: Add HS USB Host support Add device nodes for the HS USB Host port 1, USB PHY and its required regulator and also pin mux setup for HS USB1 pins. Signed-off-by: Javier Martinez Canillas Tested-by: Enric Balletbo i Serra Acked-by: Roger Quadros Signed-off-by: Benoit Cousson --- arch/arm/boot/dts/omap3-igep0020.dts | 49 ++++++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index eedf0d8b42d5..35346f2473b6 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -55,6 +55,47 @@ regulator-name = "vdd33a"; regulator-always-on; }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */ + vcc-supply = <&hsusb1_power>; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_pins + >; + + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x5aa (PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ + 0x5a8 (PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ + 0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */ + 0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */ + 0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */ + 0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */ + 0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */ + 0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */ + 0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */ + 0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */ + 0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */ + 0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ + >; + }; }; &leds_pins { @@ -166,3 +207,11 @@ smsc,save-mac-address; }; }; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; -- cgit v1.2.3