From 464ad8c43a9ead98c2b0eaed86bea727f2ad106e Mon Sep 17 00:00:00 2001 From: Hans Yang Date: Tue, 1 Dec 2015 16:54:59 +0800 Subject: usb: core : hub: Fix BOS 'NULL pointer' kernel panic When a USB 3.0 mass storage device is disconnected in transporting state, storage device driver may handle it as a transport error and reset the device by invoking usb_reset_and_verify_device() and following could happen: in usb_reset_and_verify_device(): udev->bos = NULL; For U1/U2 enabled devices, driver will disable LPM, and in some conditions: from usb_unlocked_disable_lpm() --> usb_disable_lpm() --> usb_enable_lpm() udev->bos->ss_cap->bU1devExitLat; And it causes 'NULL pointer' and 'kernel panic': [ 157.976257] Unable to handle kernel NULL pointer dereference at virtual address 00000010 ... [ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0 [ 158.031442] LR is at usb_enable_lpm+0x98/0xac ... [ 158.137368] [] usb_enable_link_state+0x34/0x2e0 [ 158.143451] [] usb_enable_lpm+0x94/0xac [ 158.148840] [] usb_disable_lpm+0xa8/0xb4 ... [ 158.214954] Kernel panic - not syncing: Fatal exception This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm() to prevent from NULL pointer access. Issue can be reproduced by following setup: 1) A SS pen drive behind a SS hub connected to the host. 2) Transporting data between the pen drive and the host. 3) Abruptly disconnect hub and pen drive from host. 4) With a chance it crashes. Signed-off-by: Hans Yang Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hub.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index bdeadc112d29..585c3cb07da6 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -5326,9 +5326,6 @@ static int usb_reset_and_verify_device(struct usb_device *udev) if (udev->usb2_hw_lpm_enabled == 1) usb_set_usb2_hardware_lpm(udev, 0); - bos = udev->bos; - udev->bos = NULL; - /* Disable LPM and LTM while we reset the device and reinstall the alt * settings. Device-initiated LPM settings, and system exit latency * settings are cleared when the device is reset, so we have to set @@ -5337,15 +5334,18 @@ static int usb_reset_and_verify_device(struct usb_device *udev) ret = usb_unlocked_disable_lpm(udev); if (ret) { dev_err(&udev->dev, "%s Failed to disable LPM\n.", __func__); - goto re_enumerate; + goto re_enumerate_no_bos; } ret = usb_disable_ltm(udev); if (ret) { dev_err(&udev->dev, "%s Failed to disable LTM\n.", __func__); - goto re_enumerate; + goto re_enumerate_no_bos; } + bos = udev->bos; + udev->bos = NULL; + for (i = 0; i < SET_CONFIG_TRIES; ++i) { /* ep0 maxpacket size may change; let the HCD know about it. @@ -5442,10 +5442,11 @@ done: return 0; re_enumerate: - /* LPM state doesn't matter when we're about to destroy the device. */ - hub_port_logical_disconnect(parent_hub, port1); usb_release_bos_descriptor(udev); udev->bos = bos; +re_enumerate_no_bos: + /* LPM state doesn't matter when we're about to destroy the device. */ + hub_port_logical_disconnect(parent_hub, port1); return -ENODEV; } -- cgit v1.2.3